Bunn ITCB-DV User Manual

2.34 Mb
Loading...

ITCB

ITCB-DV

Infusion Series®

OPERATING & SERVICE MANUAL

BUNN-O-MATIC CORPORATION

POST OFFICE BOX 3227

SPRINGFIELD, ILLINOIS 62708-3227

PHONE: (217) 529-6601 FAX: (217) 529-6644

36748.0000 03/07 ©2004 Bunn-O-Matic Corporation

www.bunn.com

BUNN-O-MATIC COMMERCIAL PRODUCT WARRANTY

Bunn-O-Matic Corp. (“BUNN”) warrants equipment manufactured by it as follows:

1)All equipment other than as specified below: 2 years parts and 1 year labor.

2)Electronic circuit and/or control boards: parts and labor for 3 years.

3)Compressors on refrigeration equipment: 5 years parts and 1 year labor.

4)Grinding burrs on coffee grinding equipment to grind coffee to meet original factory screen sieve analysis: parts and labor for 3 years or 30,000 pounds of coffee, whichever comes first.

These warranty periods run from the date of installation BUNN warrants that the equipment manufactured by it will be commercially free of defects in material and workmanship existing at the time of manufacture and appearing within the applicable warranty period. This warranty does not apply to any equipment, component or part that was not manufactured by BUNN or that, in BUNN’s judgment, has been affected by misuse, neglect, alteration, improper installation or operation, improper maintenance or repair, damage or casualty. This warranty is conditioned on the Buyer 1) giving BUNN prompt notice of any claim to be made under this warranty by telephone at (217) 529-6601 or by writing to Post Office Box 3227, Springfield, Illinois 62708-3227; 2) if requested by BUNN, shipping the defective equipment prepaid to an authorized BUNN service location; and 3) receiving prior authorization from BUNN that the defective equipment is under warranty.

THE FOREGOING WARRANTY IS EXCLUSIVE AND IS IN LIEU OF ANY OTHER WARRANTY, WRITTEN OR ORAL, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF EITHER MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. The agents, dealers or employees of BUNN are not authorized to make modifications to this warranty or to make additional warranties that are binding on BUNN. Accordingly, statements by such individuals, whether oral or written, do not constitute warranties and should not be relied upon.

If BUNN determines in its sole discretion that the equipment does not conform to the warranty, BUNN, at its exclusive option while the equipment is under warranty, shall either 1) provide at no charge replacement parts and/or labor (during the applicable parts and labor warranty periods specified above) to repair the defective components, provided that this repair is done by a BUNN Authorized Service Representative; or 2) shall replace the equipment or refund the purchase price for the equipment.

THE BUYER’S REMEDY AGAINST BUNN FOR THE BREACH OF ANY OBLIGATION ARISING OUT OF THE SALE OF THIS EQUIPMENT, WHETHER DERIVED FROM WARRANTY OR OTHERWISE, SHALL BE LIMITED, AT BUNN’S SOLE OPTION AS SPECIFIED HEREIN, TO REPAIR, REPLACEMENT OR REFUND.

In no event shall BUNN be liable for any other damage or loss, including, but not limited to, lost profits, lost sales, loss of use of equipment, claims of Buyer’s customers, cost of capital, cost of down time, cost of substitute equipment, facilities or services, or any other special, incidental or consequential damages.

BUNN, Infusion Series, BrewWISE, CDBC, DBC, ITCB, MHG, Pre-Infusion, Pulse Brew, Smart Funnel, Energy Savings, BUNNLink, Smart Reader, Freshness Timer and Sanitation Alert are either trademarks or registered trademarks of Bunn- O-Matic Corporation.

Page

36748 041504

 

INTRODUCTION

This equipment will brew either tea or coffee into an awaiting dispenser or reservoir. It can be easily configured for 120V 15 amp, 120/208V 20 amp or 120/240V 20 amp. The brewer may have an auxillary hot water faucet. It is only for indoor use on a sturdy counter or shelf.

The Infusion Series combines BrewWISE, CDBC and Tea Brewers into one. ITCB is able to brew both tea and coffee with recipe settings and has the following features: Pre-Infusion and Pulse Brew, quick and standard brew, and BrewWISE. It has an LCD for digital readout and programming along with the Smart Funnel options for coffee. The user is able to select regular or quick brew fof tea programming. Other features are Energy Savings mode, BUNNLink compatible, Smart Reader compatible, Freshness Timer and Sanitation Alert.

 

CONTENTS

Warranty..............................................................................................................

2

Introduction.........................................................................................................

3

User Notices........................................................................................................

4

Electrical Requirements.......................................................................................

6

Plumbing Requirements......................................................................................

7

Tank Drain...........................................................................................................

7

Operating Controls...............................................................................................

8

Initial Set-Up........................................................................................................

9

Tea Brewing.........................................................................................................

9

Coffee Brewing..................................................................................................

10

Cleaning.............................................................................................................

11

Glossary............................................................................................................

12

Programming....................................................................................................

14

Troubleshooting.................................................................................................

63

Wiring Diagrams................................................................................................

77

ITCB-DV..................................................................................................................

Dual Voltage Machine

ITCB-C-DV............................................................................................

Dual Voltage Machine for Canada

ITCBA............................................................................................................................

230 Volt Machine

ITCBB............................................................................................................................

200 Volt Machine

Page

36748 101505

 

USER NOTICES

Carefully read and follow all notices in this manual and on the equipment. All labels on the equipment should be kept in good condition. Replace any unreadable or damaged labels.

#00986.0000

37881.0000

Page

USER NOTICES (CONT.)

#03408.0000

#34056.0001

For 120/208V or 120/240 volt operation, replace Power Supply Cord only with Bunn-O-Matic part number 01699.0000.

#03409.0000

#34072.0000

/PTIONAL &IELD 7IRING

6 ! 7

0( ( 7IRE '.$ (:

#29710.0009

/PTIONAL &IELD 7IRING

6 ! !7 0( ( 7IRE '.$ (:

#29710.0010

Page

36748 101505

 

ELECTRICAL REQUIREMENTS

WARNING - The brewer must be disconnected from the power source until specified in Initial Set-Up.

Requirements for brewers without an attached cord set are as follows:

Refer to Data Plate on the Brewer, and local/national electrical codes to determine circuit requirements.

 

 

 

 

 

 

 

 

BACK

 

 

 

 

 

 

 

 

WHITE

RED

L2

RED

L2

 

BLK

 

 

 

WHI

 

WHI

 

120V. A.C.

L1

 

 

N

N

 

 

 

208 or 240V. A.C.

RED

 

200 or 230V. A.C.

BLUE

 

120V. A.C.

 

 

120V. A.C.

L2

 

BLK

BLK

 

 

 

 

L1

L1

 

GREEN

 

GREEN

 

 

 

 

 

 

 

 

GREEN

GREEN

GREEN

 

GREEN

 

 

 

WHITE/VIOLET

120V AC

120/208 & 120/240V AC

single phase models

single phase models

Note: The two electrical services above require 3 current carring conductors (Neutral, L1 and L2) and a separate conductor for earth ground

200 or 230V AC single phase models

Note: This electrical service consists of 2 current carrying conductors (L1 and L2) and a separate conductor for earth ground.

FRONT

DUAL VOLT

TOGGLE SWITCH

ELECTRICAL HOOK-UP

CAUTION Improper electrical installation will damage electronic components.

1.An electrician must provide electrical service.

2.Determine the available on-site electrical service.

3.Select the desired unit voltage based on the available on-site electrical service.

4.Using a voltmeter, check the voltage and color coding of each conductor at the electrical source.

5.Remove the back access panel to gain access to the terminal block.

6.Feed the supply leads through the strain relief at the rear of the brewer.

7.Using the above diagrams, connect the desired electrical service to the field wiring terminal block.

8.If wiring the machine for operation on 120/208 or 120/240 volts with a Power Supply Cord, the Power Supply Cord must be UL Listed Flexible Cord Type SO, SJO, SJTO, HSJO or SJOW, No. 12 AWG, 4 Conductor, Rated 90° C. Attachment Plug Cap must be UL Listed, NEMA 14-20P or L14-20P Configuration, Rated 125/250V, 20 AMPS. If wiring the brewer for operation at 200V or 230V with a Power Supply Cord, the Power Supply Cord must be of type “H07RN-F” with <HAR> marking, 1.5 mm2 conductor size, rated mimimom 90°C. Attachment male plug must be appropriate for Local/National use and must meet any Local/National Regulatory requirements/certifications if applicable. The Power Supply Cord must be at least 3 feet (.91 m) long and maximum 6 feet (1.82 m) long (measured from Strain Relief to end of the Attachment Plug Cap).

NOTE: If the power cord is damaged, it must be replaced by the manufacturer or its service agent or a similarly qualified person in order to avoid a hazard.

9.Connect the brewer to the power source and verify th

9.Connect the brewer to the power source and verify the voltage at the terminal block.

10.Set toggle switch on component bracket to the appropriate position and replace the access panel.

11.If plumbing is to be hooked up later be sure the brewer is disconnected from the power source. If plumbing

has been hooked up, the brewer is ready for Initial Set-Up.

Page

36748 101505

 

PLUMBING REQUIREMENTS

This brewer must be connected to a cold water system with operating pressure between 20 and 90 psi (138 and 620 kPa) from a 12" (12.7 mm) or larger supply line. A shut-off valve should be installed in the line before the brewer. Install a regulator in the line when pressure is greater than 90 psi (620 kPa) to reduce it to 50 psi (345 kPa). The water inlet fitting is 14" (6.35 mm) flare.

NOTE - Bunn-O-Matic recommends 14" (6.35 mm) copper tubing for installations of less than 25 feet (7.62 m) and 38" (9.5 mm) for more than 25 feet (7.62 m) from the 12" (12.7) water supply line. A tight coil of copper tubing in the water line will facilitate moving the brewer to clean the counter top. Bunn-O-Matic does not recommend the use of a saddle valve to install the brewer. The size and shape of the hole made in the supply line by this type of device may restrict water flow.

This equipment must be installed to comply with the Basic Plumbing Code of the Building Officials and Code Administrators International, Inc. (BOCA) and the Food Service Sanitation Manual of the Food and Drug Administration (FDA). For models installed outside the U.S.A., you must comply with the applicable Plumbing/Sanitation Code for your area.

PLUMBING HOOK UP

1.Flush the water line and securely attach it to the inlet fitting at the bottom rear of the brewer.

2.Turn on the water supply.

TANK DRAIN

1.Remove back access cover.

2.Close the white clamp on the drain hose.

3.Unfasten the hose clamp at the inlet valve. Remove the hose from the valve.

4.Place the end of the drain hose in a container that has a minimum capacity of 2.0 gallons (7.5 liters).

5.Release the white clamp to drain the water from the tank.

6.When tank is empty, leave the white clamp open, and install the hose back on the valve. Tighten the hose clamp at the end of the hose around the valve fitting.

7.Replace the back access cover.

Page

36748 101505

 

OPERATING CONTROLS

A B F D

 

 

 

4-

READY TO BREW

 

WATER TEMP: 205°

 

 

 

 

FULL

 

 

 

E

"2%7

"2%7

"2%7

HALF

 

!

"

#

 

G C

A. ON/OFF SWITCH

Pressing the "ON/OFF" pad will alternately turn the brewer on and off. Pressing this pad during the brew cycle will interrupt the brew cycle, stopping the flow of water. Pressing this pad during programming of the brewer will exit the setup and return to the main screen.

B. PROGRAMMING (left)

This hidden pad can be used to scroll backwards through the function list while in programming mode.

C. BREW (A,B,C) and FUNCTION

When the ON/OFF is ON and the brewer is on the main screen (not in programming mode), momentarily pressing and releasing this pad will begin a brew cycle. These are also used to program the brewer when in the programming mode.

D. PROGRAMMING (right)

Pressing and holding this pad allows entry into the programming menus. Pressing and releasing the pad steps through each function screen while in the programming mode.

E. BATCH SELECTOR PADS

Pressing the pad corresponding to the Half or Full batch selects the amount of product to be brewed. Pressing a different pad after a brew cycle has been initiated does not change the brew batch in progress. Light indicates the selected batch to brew. Also used in programming to adjust settings on both batch sizes.

F. FUNCTION SCREEN

This is the display which shows the various functions of the brewer and allows the programming to be accomplished.

G. FUNNEL SENSING COIL

This is used to "receive" information from the Smart Funnel handle, recipe cards, and ad cards.

Page

36748 041504

 

1.Insert an empty funnel into the funnel rails.

2.Place an empty server under the funnel.

3.Connect the brewer to the power source. Make sure the ON/OFF switch is ON (LED will be lit).

4.Water will flow into the tank and stop when the tank is filled to its capacity. Display will show PLEASE WAIT...TANK FILLING until tank is filled with water.

5. Wait approximately twenty minutes for the water in the tank to heat to the proper temperature. Display will show READY TO BREW...WATER TEMP: 205° when tank is at operating temperature. Some water will drip from the funnel during this time; this is due to expansion and should not occur thereafter.

6.Place a small vessel beneath the faucet and open the faucet handle. Release it when you hear the tank refilling.

7.Water volumes and flow settings have been preset at the factory. Refer to adjustments for the Set Brew Volumes section of this manual should the volume need to be increased or decreased.

8.The brewer is now ready for use in accordance with the

instructions for Tea Brewing and Coffee Brewing.

VIEWING ASSIGNED RECIPES & ASSET NUMBER

1.Make sure the ON/OFF switch is OFF (LED will not be lit).

2.Press and hold BREW A. The display will show the name of the recipe assigned to Brew A along with SWITCH NOT ON. This is to indicate that a brew cannot be initiated while the ON/OFF switch is OFF.

3.Repeat for BREW B and BREW C.

4.Make sure the ON/OFF switch is OFF. To view the asset number of the machine, press and hold the left hidden button until the display reads: ANXXXXXX...ASSET NUMBER. Release the left hidden button.

5.After a 5 second delay, the display will read: ITCBXXXXXX. This is the serial number of the machine.

Page

36748 101505

 

TEA BREWING

1.Begin each brew cycle with a clean empty brew funnel and server. (Be sure the server lid doesn’t interfere with the flow of dilution water.)

2.Insert a BUNN filter into the funnel.

3.Pour the packet of loose fresh tea leaves into the filter. Approximately three to five ounces is recommended for three gallons of beverage.

4.Level the bed of tea leaves by gently shaking.

5.Slide the funnel into the funnel rails until it stops.

6.The ON/OFF must be ON. Select which batch size to brew.

7.Momentarily press and release the assigned BREW button. There may be certain situations in which the brew cycle will not begin when BREW is pressed:

a.SWITCH NOT ON - ON/OFF must be ON.

b.BREW TEMPERATURE TOO LOW – wait until heated or cancel BREW LOCKOUT option (Page 17).

c.CHECK FUNNEL – remove funnel, empty previously brewed leaves and replace with fresh tea leaves.

d.DISABLED - select different brew button or batch size.

8.If none of the above messages are displayed, the display will read NOW BREWING and show the time remaining in the brew cycle.

9.Following the brew will be a countdown of drip time DRIPPING which shows the time remaining until the tea no longer drips from the funnel tip.

10.Carefully remove the brew funnel and discard the tea leaves and filter only after visible dripping stops.

COFFEE BREWING

WITHOUT A SMART FUNNEL AND G9-2T DBC GRINDER:

1.Begin each brew cycle with a clean empty brew funnel.

2.Insert a BUNN filter into the funnel.

3.Pour the fresh coffee into the filter and level the bed of grounds by gently shaking.

4.Slide the funnel into the funnel rails until it stops.

5.Place an empty server under the funnel.

6.The ON/OFF must be ON. Select the FULL batch size.

7.Momentarily press and release the assigned BREW button. There may be certain situations in which the brew cycle will not begin when BREW is pressed:

a.SWITCH NOT ON - ON/OFF must be ON.

b.BREW TEMPERATURE TOO LOW – wait until heated or cancel BREW LOCKOUT option (Page 17).

c.CHECK FUNNEL – remove funnel, empty previously brewed grounds and replace with fresh.

d.DISABLED - select different brew button or batch size.

e.COFFEE FUNNEL? – appears when brew volume is greater than 86.0 oz. (2.54 L) and pulse brew is disabled. Check to make sure the correct funnel is in place, and then press BREW again.

8.If none of the above messages are displayed, the display will read NOW BREWING and show the time remaining in the brew cycle.

9.Following the brew will be a countdown of drip time DRIPPING which shows the time remaining until the coffee no longer drips from the funnel tip.

10.Carefully remove the brew funnel and discard the grounds and filter only after visible dripping stops.

WITH A SMART FUNNEL AND G9-2T DBC or MHG GRINDER:

1.Select the small batch size on the grinder.

2.Insert a BUNN filter into the funnel.

3.Grind the selected amount of fresh coffee into the Smart Funnel using the G9-2T DBC or MHG with Smart Funnel operation and level the grounds by gently shaking.

4.Slide the funnel into the funnel rails. The brewer will read the coffee name and size ground through the chip

in the funnel handle.

Page 10

36748 101505

 

NOTE: The brewer will automatically match the brew batch size to the grinder batch size:

GRINDER

BREWER

Small

Half Batch

Medium

Full Batch

Large

*Full Batch

*If BREW is pressed with a large grinder batch, the display will read: INCORRECT GRIND...BATCH SIZE WRONG, and then PRESS BREW TO BREW ANYWAY.

5.Place an empty server under the funnel.

6.The ON/OFF must be ON.

7.Momentarily press and release the assigned BREW button. There may be certain situations in which the brew cycle will not begin when BREW is pressed:

a.SWITCH NOT ON - ON/OFF must be ON.

b.BREW TEMPERATURE TOO LOW – wait until heated or cancel BREW LOCKOUT option (Page 17).

c.CHECK FUNNEL – remove funnel, empty previously brewed grounds and replace with fresh.

d.INCORRECT GRIND - Indicates a large batch was ground using the grinder. Check batch size and grind weight.

8.If none of the above messages are displayed, the display will read NOW BREWING and show the time remaining in the brew cycle.

9.Following the brew will be a countdown of drip time DRIPPING which shows the time remaining until the coffee no longer drips from the funnel tip.

10.Carefully remove the brew funnel and discard the grounds and filter only after visible dripping stops.

CLEANING

CAUTION – CLEAN AND SANITIZE YOUR ICED TEA BREWER DAILY

1.Remove and thoroughly clean the entire brew funnel. The funnel tip and screen must be free from any tea particles or residue. Reassemble the funnel.

2.Remove and thoroughly rinse the sprayhead. The holes must be open and clear of any mineral deposits. Wipe the sprayhead panel clean with a damp cloth.

NOTE – Any buildup on the sprayhead may restrict water flow, and impact yuor brewing. For consistently great tea and coffee, clean sprayhead weekly with sprayhead cleaning tool (#38227.0000). Upon visual inspection it may appear that light passes through all holes in the sprayhead, but a thin film of residue can pass light and still impede water flow.

a.Remove sprayhead from brewer.

b.Use the pointed end of sprayhead cleaning tool to remove any mineral deposits from the sprayhead holes.

c.Insert the long end of sprayhead cleaning tool into the sprayhead fitting, and rotate several times to remove any mineral deposits from the fitting.

3.The use of a damp cloth rinsed in any mild, nonabrasive, liquid detergent is recommended for cleaning all surfaces on Bunn-O-Matic equipment. Do NOT clean this equipment with a water jet device.

CAUTION – DO NOT KEEP BREWED ICED TEA OVERNIGHT. THE SERVER MUST BE CLEANED DAILY.

See page 50 of instruction manual for calibration routine to verify sprayhead flow rate matches programmed flow rate. Brewer may need to be re-calibrated due to lime build up. If brewer is cleaned and build up removed, brewer must be re-calibrated to achieve desired volumes.

Page 11

36748 101505

 

GLOSSARY

AD CARD: An assembly consisting of computer chips and an instruction label. Used for loading advertising messages into the brewer.

AUTO PULSE BREW SETUP: The setting of a pulse brew routine by entering in the total desired brew time. The brewer will then calculate and perform a pulse brew routine using a predetermined formula.

BREW LOCKOUT: The inability to initiate a brew if the water temperature is less than the ready temperature programmed into the brewer.

CHIP: A computer chip containing either recipes for specific coffee flavors or advertising messages that are read by the sensing coil on the brewer. One chip is embedded in each Smart Funnel handle to carry the coffee flavor name and batch size ground from the grinder to the brewer.

DILUTION: Water added to tea concentrate.

DILUTION DELAY: The length of time from when the brew is initiated until the dilution water starts.

DRIP TIME: The length of time from when the water spray over the grounds ends to the time when no water or product drips from the funnel tip.

ENERGY SAVINGS MODE: If enabled, the brewer will either shut down or reduce the tank holding temperature to 140°F (60°C) after the set idle time.

FACTORY DEFAULTS: The factory preset brew settings that were installed into the brewer’s memory.

FIRST ON-TIME: During a pulse brew, this is the time set for the initial flow of water over the grounds or tea leaves.

FRESHNESS TIMER: If enabled, the brewer will display an alert if a new tea or coffee batch has not been brewed before the set time has expired.

FUNNEL SENSING COIL: A sensor at the front of the brewer that reads what name and batch size of coffee was ground into the funnel and allows for the brewer to automatically set itself to what is read from the funnel handle. Also used to read in recipe and ad card information.

IDLE TIME (ENERGY SAVINGS MODE): If ENERGY SAVINGS Mode is enabled, the length of time the brewer is inactive before the machine turns off or holds at 140°F (60°C).

LAST ON-TIME: During a pulse brew, this is the time set for the second on-time and each alternative on-time for the remainder of the brew.

MAIN SCREEN: The term used to describe the screen that is displayed when the brewer is not in use. This screen is also displayed after exiting the programming mode.

MANUAL PULSE BREW SETUP: The setting of a pulse brew routine by manually entering in the 1st on time, off time and last on time.

MASTER TEMP: The temperature at which the tank will heat to and hold. If the brewer is in Master Temp mode, all initiated brews will be at this temperature.

OFF-TIME: During a pulse brew or preinfusion, this is the time set for the length of time that the water is not spraying over the grounds.

PREINFUSION: The process of beginning a brewing cycle with an initial spray of water onto the grounds followed by a pause in the spray. After the programmed pause, the spray continues without interruption until the end of the brewing cycle.

PULSE BREW: The process that allows the brew water to start, and then stop, repeatedly over the grounds or tea leaves in order to derive the best flavor from the coffee or tea. Pulse brew is also used in some instances to prevent a funnel overflow.

Page 12

36748 041504

 

GLOSSARY (Continued)

RECIPE: Set of brewing parameters stored in the brewer. The parameters are unique for each tea and coffee name. Tea recipes include brew ounces, dilution ounces, dilution delay, pulse brew, and drip time. Coffee recipes include brew ounces, pulse brew and drip time.

RECIPE CARD: An assembly consisting of a computer chip and an instruction label. Used for loading a recipe into the brewer and the companion DBC Grinder.

RECIPE TEMPS: Allows a different temperature to be set for each brew recipe.

NOTE – Using this setting will override the Master Temp setting. The tank will hold at the lowest set temperature. A short heating time may be required if all brew recipes are not set at the same temperature.

SANITATION MODE: If enabled, the brewer will display a message after a set amount of time indicating the machine needs cleaning and sanitizing.

TEA 1, TEA 2, TEA 3, HOT TEA, ICED COFFEE, NO-NAME COFFEE: The preset recipes stored in the brewer. Used by the brewer when there is no coffee name stored in the Smart Funnel or if a recipe card is not used. WARNING TIME (FRESHNESS TIMER): If the Freshness Timer is enabled, the length of time from when the brew was completed until a “Freshness Alert” message will display, communicating that a fresh batch of product needs to be brewed.

Page 13

36748 080904

 

Using the menu-driven display on the front of brewing parameters such as brew temperatures, for the precise brewing of various flavors of tea

Programming of the brewer is achieved programming switches and the brew/function specifications.

To access the programming mode, and to switches are used. There are five of these switches

PROGRAMMING SECTION

 

 

REVIEW/MODIFY/SETUP COFFEE RECIPES

 

 

 

-------------------------------------------------------BREW OZ

34

 

 

---------------------------------------------------PULSE BREW

35

BREW LOCKOUT

17

------------------------------------------------------DRIP TIME

39

 

 

-SET----------------------------------------------------------TEMP

40

 

 

-READY---------------------------------------------------DEGREE

41

 

 

-ENABLE-------------------------------------------------------ADS

42

 

 

-ENABLE---------------------------------------------SANITATION

44

DISABLE BREW SWITCH

21

-ENABLE-----------------------------------------ENERGY SAVER

45

 

 

-ENABLE------------------------------------FRESHNESS TIMER

46

FUNNEL AND GRINDER)

22

-REFILL--------------------------------------------------------------

47

 

 

-FLOW-------------------------------------------------------RATES

48

 

 

-CALIBRATE-------------------------------------------------FLOW

50

---------------------------------GRINDER OR RECIPE CARD)

25

-BREW-------------------------------------------------COUNTERS

52

 

 

-SET-----------------------------------------------RECIPE TEMPS

53

-------------------------------------------------------BREW OZ

26

-ASSET---------------------------------------------------NUMBER

54

 

26

-SERVICE------------------------------------------------NUMBER

55

------------------------------------------------------DILUTE OZ

27

-SERVICE---------------------------------------------------TOOLS

56

 

28

-FACTORY----------------------------------------------DEFAULTS

60

---------------------------------------------------PULSE BREW

29

-DEFAULT-----------------------------------------------SETTINGS

61

------------------------------------------------------DRIP TIME

33

 

 

(justbcto the leftd of the display):e This is used to scroll backwards through

PROGRAMMING THE BREWER

The programming of the brewer is divided into two levels. There is one function in Level 1. All other functions are accessed in Level 2.

The following function screens are in order of appearance. Each screen will have instructions on how to access and the procedures to program the various functions of the brewer.

IMPORTANT PROGRAMMING NOTES

- READ CAREFULLY -

To exit the programming mode at any time, press and release the ON/OFF pad located on the front switch panel. The display will return to the MAIN SCREEN.

If none of the five programming switches are pressed within one minute during the setup of the brewer, the programming of the function screen that is being set will be exited and the display will return to the MAIN

SCREEN.

Always remember to place a container and funnel under the sprayhead when operating the brewer during the set-up of CALIBRATE FLOW, and testing the brew and dilution valves in SERVICE TOOLS/TEST OUTPUTS.

MAIN SCREEN

READY TO BREW

WATER TEMP: 205°

BREW

BREW

BREW

A

B

C

This screen will be shown when the brewer is ready for use. The screen displays the water temperature in the tank. When the water in the tank reaches the correct set temperature, the display will change from

HEATING to READY TO BREW.

PROGRAMMING LOCKOUT SWITCH ((located on the memory module board prior to S/N ICB0007479 - located on the main circuit board S/N ICB0007479 and after))

This switch can be set to prevent access to the programming settings of the brewer. Once all the correct brew settings are programmed, the operator can set the switch to the "ON" position to prohibit anyone from changing the settings. With the switch in the "ON" position, the programming menus can still be accessed to view the current settings. However, no changes will be saved.

UNLOCK

MEMORY

 

LOCK

 

PROGRAMMING

LOCKOUT SWITCH

P3048

Page 15

36748 070706

 

PROGRAMMING THE BREWER (cont.)

PROGRAMMING FUNCTIONS - FLOW CHART

PROGRAMMING FUNCTIONS - LEVEL I

PROGRAMMING FUNCTIONS - LEVEL 2

BREW LOCKOUT? NO DONE YES

BREW

BREW

BREW

A

B

C

SET LANGUAGE?

 

UNITS

 

REVIEW RECIPES

ASSIGN RECIPE

NO

 

YES

METRIC DONE

ENG

NO

 

YES

NO

 

YES

BREW

BREW

BREW

BREW

BREW

BREW

BREW

BREW

BREW

BREW

BREW

BREW

A

B

C

A

B

C

A

B

C

A

B

C

SET NEW RECIPE?

SET TEMP 205°

READY DEGREE 5°

ENABLE ADS?

NO

 

YES

(-)

DONE

(+)

(-)

DONE

(+)

NO

DONE

YES

BREW

BREW

BREW

BREW

BREW

BREW

BREW

BREW

BREW

BREW

BREW

BREW

A

B

C

A

B

C

A

B

C

A

B

C

ENABLE SANITATION

ENABL ENERGYSAVR

ENABLE FRESH TIMER

XX

REFILL

XXX

NO

DONE

YES

NO

DONE

YES

NO

DONE

YES

(-)

DONE

(+)

BREW

BREW

BREW

BREW

BREW

BREW

BREW

BREW

BREW

BREW

BREW

BREW

A

B

C

A

B

C

A

B

C

A

B

C

SPRAY OZ/M:

XX.X

DILUTE OZ/M:

XX.X

CALIBRATE FLOW?

BREW COUNTERS?

(-)

DONE

(+)

(-)

DONE

(+)

NO

 

YES

NO

 

YES

BREW

BREW

BREW

BREW

BREW

BREW

BREW

BREW

BREW

BREW

BREW

BREW

A

B

C

A

B

C

A

B

C

A

B

C

SET RECIPES TEMPS

ENTER ASSET #

ENTER SERVICE #

SERVICE TOOLS

NO

 

YES

NO

 

YES

NO

 

YES

NO

 

YES

BREW

BREW

BREW

BREW

BREW

BREW

BREW

BREW

BREW

BREW

BREW

BREW

A

B

C

A

B

C

A

B

C

A

B

C

FACTORY DEFAULTS

 

 

 

 

 

 

 

 

 

NO

 

YES

 

 

 

 

 

 

 

 

 

BREW

BREW

BREW

 

 

 

 

 

 

 

 

 

A

B

C

 

 

 

 

 

 

 

 

 

Page 16

36748 080904

 

PROGRAMMING THE BREWER (cont.)

PROGRAMMING FUNCTIONS - LEVEL I

BREW LOCKOUT

This function allows the operator to prevent or allow brewing if the water temperature is less than the set READY temperature.

Procedure for setting Brew Lockout:

1. To access this function screen press and hold the right hidden button. Release when the display reads:

BREW LOCKOUT?

NO DONE YES

BREW

BREW

BREW

A

B

C

Press here Press here Press here for NO for DONE for YES

2.The YES or NO should be flashing. Select YES to prevent brewing if the water temperature is below the set READY temperature. Select NO to permit brewing at any water temperature.

3.When finished, press and release DONE. This will exit this function screen and return to the MAIN SCREEN on the display.

Page 17

36748 041504

 

PROGRAMMING THE BREWER (cont.)

PROGRAMMING FUNCTIONS - LEVEL 2 (cont.)

The functions in the second level of programming allow the operator to adjust brew settings and other feature options.

To access the level 2 function screens press and hold the right hidden button. Release when the display reads:

SET LANGUAGE

This function allows the operator to select the language used for the display.

Procedure for setting Language:

1.Press and hold the right hidden button until the display reads SET LANGUAGE? and release.

2.Press YES to proceed. The display should now read ENGLISH. Using (-) and (+), scroll through the available languages until the desired language is shown on the display.

3.When finished, press DONE. If the language selected is different from the current settings,the display will read CHANGE LANGUAGE? ARE YOU SURE? and then will change to CHANGE LANGUAGE? To convert the display to the new language, press YES. To retain the current language, press NO.

4.The display should now read UNITS. To exit programming and return to the MAIN SCREEN, press and release the ON/OFF button.

SET LANGUAGE?

NO

 

YES

BREW

BREW

BREW

A

B

C

 

ENGLISH

 

 

 

 

(-)

DONE

(+)

 

 

 

 

 

 

 

UNITS

 

BREW

BREW

BREW

METRIC DONE

ENG

A

B

C

 

 

 

 

 

 

BREW

BREW

BREW

 

 

 

A

B

C

 

ESPANOL

 

 

 

 

(-) SELECCIONE (+)

 

 

 

BREW

BREW

BREW

 

 

 

A

B

C

 

 

 

Scrolls through all available languages in memory

Page 18

36748 080904

 

PROGRAMMING THE BREWER (cont.)

PROGRAMMING FUNCTIONS - LEVEL 2 (cont.)

UNITS

This function allows the operator to select if numeric settings are displayed in English or Metric units.

Procedure for setting the Units:

1.Press and hold the right hidden button until the display reads SET LANGUAGE? Press and release the right hidden button until the display raeds UNITS. The METRIC or ENG should be flashing.

2.Select METRIC to have settings displayed in Metric units. Select ENG to have setting displayed in English units.

NOTE: Changing the UNIT settings will restore ALL settings to Factory Default.

3. When done, press and release DONE to retain your settings and advance to the next programming screen. To exit programming and return to the Main Screen, press and release the ON/OFF button.

NOTE: This manual is written based on Factory Default settings (English Units). If the brewer is set for Metric Units, display will be different. (ex: Brew oz will become Brew ml).

SET LANGUAGE?

 

UNITS

 

NO

 

YES

METRIC DONE

ENG

BREW

BREW

BREW

BREW

BREW

BREW

A

B

C

A

B

C

Page 19

36748 101505

 

PROGRAMMING THE BREWER (cont.)

PROGRAMMING FUNCTIONS - LEVEL 2 (cont.)

REVIEW RECIPES (Modify recipe, set up standard recipes)

This function has three parts:

1.It allows the operator to view the brew settings for the various tea and coffee recipes stored into the brewer.

2.It allows the operator to modify (change) any of the brew settings for a particular recipe stored in the brewer.

3.It is used to set up the standard recipes for Tea, Hot Tea, Iced Coffee and No-Name Coffee.

Procedure for reviewing the recipes:

1.Press and hold the right hidden button until the display reads SET LANGUAGE. Press the right hidden button until the display reads REVIEW RECIPES. Press YES.

2.The display should now read TEA 1, along with

MODIFY SHOW and NEXT.

3.Press and release SHOW. The screen will scroll through all the brew settings for that particular recipe. When finished, the display will return to the recipe name just viewed.

4.To see the settings again, press SHOW. To advance to the next recipe, press NEXT.

5.To exit, press NEXT until the display reads THAT WAS THE LAST RECIPE.

6.After 5 seconds, the display will return to the REVIEW RECIPES screen. Press and release NO to advance to the next function screen, or press and release the ON/OFF pad to exit the programming mode and return to the MAIN SCREEN.

 

REVIEW RECIPES

 

 

 

 

 

NO

 

 

 

YES

 

 

 

 

 

BREW

BREW

BREW

 

 

 

 

 

A

 

B

C

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

PRESSING NO WILL

 

 

 

 

 

TEA 1

 

 

 

ADVANCE TO NEXT

 

 

 

 

 

 

 

 

FUNCTION SCREEN

 

 

MODIFY SHOW NEXT

 

 

 

 

 

 

 

 

 

 

 

 

 

BREW

BREW

BREW

 

 

 

 

 

 

 

PRESSING BREW B

 

 

SCROLLS THROUGH

 

A

B

C

 

ALL BREW SETTINGS

 

 

 

 

 

 

 

 

FOR THAT RECIPE

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

TEA 2

 

 

 

 

 

 

 

MODIFY SHOW NEXT

 

 

 

 

 

 

 

 

 

 

PRESSING BREW B

 

BREW

BREW

BREW

 

SCROLLS THROUGH

 

 

ALL BREW SETTINGS

 

A

B

C

 

FOR THAT RECIPE

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

SCROLLS THROUGH

 

 

 

 

 

 

 

 

 

ALL DEFAULT RECIPES

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

NO-NAME COFFEE

MODIFY SHOW NEXT

ARE YOU CREATING OR CHANGING

A RECIPE FOR A COFFEE NAME PRE-

VIOUSLY USED IN THIS BREWER?

 

DON'T

YES

NO

 

 

KNOW

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

HAVE YOU RECIEVED A

 

 

 

 

 

RECIPE CARD CONTAINING

 

 

 

 

 

 

THE NEW RECIPE?

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

YES

 

 

 

NO

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

FOLLOW INSTRUCTIONS

 

DOES THE GRINDER HAVE

 

 

ON THE RECIPE CARD

 

THE NAME IN ITS MEMORY?

 

 

 

 

 

 

NO

DON'T

 

 

 

 

 

 

 

 

 

 

 

 

YOU WILL MODIFY

 

YOU WILL MODIFY

 

 

AN EXISTING RECIPE

 

THE NO NAME COFFEE

 

 

 

 

BREW SETTINGS

 

 

 

 

 

 

 

 

 

 

 

 

 

 

GO TO REVIEW RECIPES, PAGE

 

 

 

 

 

 

 

 

26 AND FOLLOW INSTRUCTIONS

 

 

 

OR

 

 

 

 

 

 

 

 

 

 

 

 

SEE RECIPE CHART ON THIS PAGE

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

FOR A LIST OF EXISTING RECIPES.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

KNOW YES

GO TO SET NEW RECIPE,

PAGE 21 AND FOLLOW

THE INSTRUCTIONS

REFER TO NAME LIST

IN GRINDER MANUAL

CONTACT BUNN-O-MATIC

FOR ASSISTANCE

Page 20

PRESSING BREW B

BREW

BREW

BREW

SCROLLS THROUGH

ALL BREW SETTINGS

A

B

C

FOR THAT RECIPE

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

(RECIPE NAME)

 

 

MODIFY SHOW NEXT

PRESSING BREW B

 

BREW

BREW

BREW

 

SCROLLS THROUGH

 

ALL BREW SETTINGS

 

A

B

C

FOR THAT RECIPE

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

THAT WAS THE

 

 

LAST RECIPE

 

 

 

P2859

 

 

 

 

 

 

RECIPE CHART

 

 

Tea 1

 

Iced Coffee

 

 

Tea 2

 

No Name Coffee

 

OR

Tea 3

 

 

 

Hot Tea

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

36748 070706

PROGRAMMING THE BREWER (cont.)

PROGRAMMING FUNCTIONS - LEVEL 2 (cont.)

ASSIGN RECIPE

This function allows the operator to assign recipes to the three brew buttons. Standard recipes (TEA 1, TEA 2, TEA 3, HOT TEA, ICED COFFEE, NO-NAME COFFEE) and any saved recipes from a Smart Funnel or Recipe Card can be assigned to a brew button. Only one recipe per brew button is allowed, for a total three recipes available to brew.

NOTE: Factory Defaults assign the TEA 1 recipe to Brew A, HOT TEA recipe to Brew B, and NO-NAME COFFEE to Brew C.

Procedure to select switch recipes:

1.Press and hold the right hidden button until the display reads SET LANGUAGE. Press the right hidden button until the display reads SELECT SWITCH RECIPE? Press YES.

2.The display should now read SELECT RECIPE BREW SWITCH A, and then TEA 1.

3.Using (-) and (+), scroll through the stored recipes in the brewer’s memory until the desired recipe name is reached.

4.Press and release DONE to set that recipe for brew button A.

5.The display should now read SELECT RECIPE BREW SWITCH B, and then HOT TEA.

6.Using (-) and (+), scroll through the stored recipes in the brewer’s memory until the desired recipe name is reached.

7.Press and release DONE to set that recipe for brew button B.

8.The display should now read SELECT RECIPE BREW SWITCH C, and then NO-NAME COFFEE.

9.Using (-) and (+), scroll through the stored recipes in the brewer’s memory until the desired recipe name is reached.

10.Press and release DONE to set that recipe for brew button C.

11.The display should now read REVIEW RECIPES.

Procedure to disable a Brew Switch:

1.Follow the same procedure as above. When selecting the recipe for the brew switch to be disabled, use (-) and (+) to scroll until the display reads DISABLED.

2.Press and release DONE to disable that brew switch on that side.

ASSIGN RECIPE

NO

 

 

YES

BREW

BREW

BREW

A

B

C

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

EXIT TO

 

 

SELECT RECIPE

NEXT FUNCTION

 

 

SCREEN

 

 

BREW SWITCH A

 

 

 

 

 

 

 

 

TEA 1

(-) DONE (+)

SCROLL THROUGH

BREW

BREW

BREW

STORED RECIPES

A

B

C

IN BREWER MEMORY

 

 

 

 

SELECT RECIPE

BREW SWITCH B

HOT TEA

(-) DONE (+)

SCROLL THROUGH

BREW

BREW

BREW

STORED RECIPES

IN BREWER MEMORY

A

B

C

 

 

 

 

SELECT RECIPE

BREW SWITCH C

NO-NAME COFFEE (-) DONE (+)

SCROLL THROUGH

BREW

BREW

BREW

STORED RECIPES

IN BREWER MEMORY

A

B

C

SET NEW RECIPE

NO YES

BREW

BREW

BREW

P2858

A

B

C

Page 21

36748 101505

 

PROGRAMMING THE BREWER (cont.)

PROGRAMMING FUNCTIONS - LEVEL 2 (cont.) SET NEW RECIPE (to set a new COFFEE recipe using a Smart Funnel or RECIPE CARD)

Using a Smart Funnel and a G9-2T DBC or MHG Grinder:

This function allows the operator to set BREW VOLUMES, PULSE BREW TIMES AND DRIP OUT TIMES for each coffee name preset in the grinder’s memory.

SET NEW RECIPE?

NO YES

BREW

BREW

BREW

A

B

C

MASTER TEMP XXX°

NO YES

Certain coffee names are stored in the grinder’s memory. When a particular name of coffee is ground into the Smart Funnel, that name and the batch size selected are transferred from the grinder to the programming CHIP located in the funnel handle. The funnel is then inserted into the brewer’s funnel rails. The SENSING COIL on the brewer reads the information contained in the handle. The name of the coffee flavor will then appear on the display. This allows the operator to set the BREW VOLUME, PULSE BREW TIMES and DRIP OUT TIME for that particular coffee name. It also allows the operator to set other brewing parameters, such as

BREW TEMPERATURE, BREW LOCKOUT, etc. Each coffee name can be set individually to provide optimum brewing quality.

 

INSERT FUNNEL

CYCLES THROUGH

WITH NEW NAME

TWO SCREENS

 

 

 

 

 

2 SEC.

 

 

QUIT SETUP?

 

 

YES

 

 

BREW

BREW

BREW

 

A

B

C

 

 

FUNNEL DETECTED

 

FUNNEL

 

FUNNEL CONTAINS

 

CONTAINS NAME

NO NAME

(COFFEE NAME)

 

 

 

MUST GRIND INTO

NO

 

 

YES

 

 

 

FUNNEL FIRST

BREW

BREW

BREW

 

 

 

 

 

A

B

C

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

BEGIN SETUP OF

 

 

 

 

 

 

 

 

 

 

(COFFEE NAME)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

SET UP BREW VOLUMES, BYPASS PERCENTAGE,

 

SEE SEPARATE DIAGRAMS

 

 

 

PULSE BREW TIMES, AND DRIP OUT TIME

 

FOR SETUP INSTRUCTIONS

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

2 BATCHES DONE?

 

 

 

 

 

NO

 

 

 

 

YES

 

 

 

 

 

BREW

BREW

BREW

 

 

 

 

 

A

B

C

 

 

 

 

 

 

 

 

 

 

 

 

 

 

P2854-1

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

(COFFEE NAME) SETUP COMPLETE

Page 22

36748 101505

 

Page 23

PROGRAMMING THE BREWER (cont.)

PROGRAMMING FUNCTIONS - LEVEL 2 (cont.) Procedure for Setting the Recipe:

NOTE: Before beginning setup, place a server beneath the brew funnel.

1.Insert the funnel into the grinder and select the small batch size to grind. It is not necessary to have coffee beans in the hopper(s) in order to program the brewer. The coffee name is pre-selected and stored in the grinder’s memory for the side being ground.

2.Press the GRIND pad. When the grinder stops grinding, remove the funnel.

3.On the brewer, press and hold the right hidden button until the display reads SET LANGUAGE. Press and release the right hidden button until the display reads SET NEW RECIPE. Release the right hidden button.

4.Press and release YES. The display should read

INSERT FUNNEL WITH NEW NAME, then QUIT SETUP? These two displays will repeatedly cycle.

5.Insert the funnel into the rails on the brewer. The display should read the name of the coffee that was ground into the funnel, along with a NO and YES. If the name on the display is correct, press YES.

6.If, for some reason, the name of the coffee from the grinder did not load properly into the funnel, or if a grind has not yet been done, the display will read MUST GRIND INTO FUNNEL FIRST. It will be necessary to grind another batch following steps 1 and 2.

NOTE: If brewer memory is full, the display will read

RECIPE STORAGE AREA IS FULL and then REMOVE A FLAVOR? To remove a recipe press and release YES.PressNEXTtoscrollthroughthestoredrecipes. When the display reads the name of the recipe to be removed, press and release REMOVE. The display will read REMOVE? Press CANCEL to exit the SET NEW RECIPE function. Press OK to remove that recipe. The display will then show BEGIN SETUP OF (COFFEE NAME). Continue with step 7.

7.If the grind is acknowledged by the brewer, the display will read BEGIN SETUP OF (COFFEE NAME). Then the screen will display BREW OZ and a batch light will be blinking. (Refer to page 34 for description of BREW OZ function).

8.Using (-) and (+), set the amount of brew water to be dispensed for that batch size.

9.When finished, press the other batch size and repeat step #8.

10.When finished setting both batch sizes, press and release DONE. The display should read 2 BATCHES

DONE?

11.If both batch sizes are not correct press and release NO to return to the BREW OZ setup screen and repeat steps #8, 9 and 10.

12.If both batch sizes are correct, press and release YES to advance to the SET PULSE BREW function. (Refer to page 35 for description of the SET PULSE BREW function.

13.To SET PULSE BREW press YES and proceed with the setup instructions for SETTING PULSE BREW, on page 35.

14.To skip setting the PULSE BREW and to use the FACTORY DEFAULTS, press NO to proceed to the

DRIP TIMES function.

BREW OZ XX.X (-) DONE (+)

BREW

BREW

BREW

A

B

C

SET PULSE BREW

NO YES

BREW

BREW

BREW

A

B

C

DRIP TIME XX.X (-) DONE (+)

BREW

BREW

BREW

A

B

C

(COFFEE NAME) SETUP COMPLETE

5 SEC.

THAT WAS THE

LAST RECIPE

P2855

MASTER TEMP XXX°

NO YES

36748 051304

PROGRAMMING THE BREWER (cont.)

PROGRAMMING FUNCTIONS - LEVEL 2 (cont.)

15.The display should now read DRIP TIME, along with either the word OFF or a time showing. A batch light will also be blinking.

16.Using (-) and (+), set the amount of time from when the brew spray ends to when the funnel is emptied of hot liquid.

17.When finished, press the other batch size and repeat step #16

18.When finished setting both batch sizes, pressDONE. The display should read 2 BATCHES DONE?

19.Press and release YES.The screen should show the name of the coffee being programmed (modified) along with SETUP COMPLETE.

20.After a 5 second delay, the display will advance to the next coffee name in the brewer’s memory. If no other coffee names are present, the display will read THAT WAS THE LAST RECIPE, and advance to the MASTER TEMP screen.

SET NEW RECIPE

Using a RECIPE CARD to load coffee names and brew settings

The G9-2T DBC or MHG Grinder’s memory contains certain coffee names. If the operator uses a coffee name that is not already stored in the grinder’s memory, a RECIPE CARD can be obtained from the factory. The RECIPE CARD would include all the information needed to set up that particular coffee name. The information from the RECIPE CARD is loaded into the grinder’s memory, then into the brewer’s memory by holding the chip area up to the equipment’s SENSING COIL. This information can include the coffee name, BREW VOLUMES, PULSE BREW TIMES and DRIP OUT TIME for that particular coffee name. These can all be loaded in seconds.

Contact Bunn-O-Matic Corporation for the availability of RECIPE CARDS.

NOTE: Instructions to program the brewer and grinder are printed on the RECIPE CARD, along with the coffee name that is being programmed.

Procedure to program the coffee name:

1.Remove the funnel (if present) from the funnel rails.

2.Position the RECIPE CARD vertically, so that the top end of the CHIP is beneath the SENSING COIL (located on the middle of the underneath side of the front display panel).

3.After a short pause the display will read CARD CONTAINS RECIPE FOR then will change to (COFFEE NAME) SHOW QUIT SAVE. All brewing parameters for that coffee flavor are now transferred from the CARD to the brewer.

READY TO BREW

WATER TEMP: 205°

POSITION CARD UNDER

SENSOR COIL

CARD CONTAINS

RECIPE FOR

5 SEC.

(COFFEE NAME) SHOW QUIT SAVE

BREW

BREW

BREW

A

B

C

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

SCROLLS THROUGH

 

 

(COFFEE NAME)

ALL BREW SETTINGS

 

 

FOR THAT RECIPE

 

 

SETUP COMPLETE

 

 

 

 

 

 

 

 

 

 

 

 

 

 

(COFFEE NAME)

NOT SAVED

READY TO BREW

WATER TEMP: 205°

P2856

Page 24

36748 101505

 

+ 55 hidden pages