RCT 520
USER GUIDE
Read Before Use!
www.BulletTools.com • 208-772-0175
RCT 526
SERIES
RCT 520
PRT-INS-5RCT.RevA.11.13 ©2013 Bullet Tools
1
1 ����� READ AND UNDERSTAND THIS INSTRUCTION MANUAL BEFORE OPERATING THE RCT�
2 �����If you are not thoroughly familiar with the operation of the RCT Shear, obtain advice from a
qualied instructor or call 800-406-8998 (Intl.: 208-772-0175).
3 �����Stay alert. Do not operate while under the inuence of drugs, alcohol, or medication.
4 �����Always wear safety approved eye protection with side shields (ANSI Z87.1).
5 �����Keep work area clean and free of debris.
6 �����Recommended operating temperature range: 20° F (-6° C) to 115° F (46° C)
7 �����Keep children and unauthorized persons away from the Shear and work area.
8 �����Make sure tool is secure. Operate only on a rm substrate or solid stand.
9 �����Use the right tool. Do not force the RCT Shear or use it for a job for which it was not intended;
the RCT Shear is designed to cut carpet tile, VCT, LVT, PVC tile, vinyl tile & residential grade/
low-pressure laminate ooring. See Cut Guide page 7.
10 ���Keep Blade sharp. A dull Blade will not perform properly.
11 ���Always keep hands away from Blade while operating or carrying.
12 ���Do not alter or misuse this tool. The RCT Shear is precision built; modications not specied in
this manual may result in a dangerous condition.
13 ���Maintain RCT Shear with care. Keep Blade sharp and clean. Follow instructions for lubricating
and changing accessories. See page 7.
14 ���Use only recommended accessories. The use of improper accessories may cause hazards or
injur y.
15 ���Never leave the RCT Shear unattended. Secure the Handle with the Safety Lock when not in
use. See page 6.
16 ���Warning: The dust generated by cutting certain wood, wood ber and/or PVC products can
be hazardous to your health. The RCT Shear generally does not produce any dust; however,
minimal creation of dust may be possible. Avoid ingesting any dust created through cutting.
SAFETY GUIDE FOR THE
MAGNUM
™
RCT SERIES
WARNING: FAILURE TO FOLLOW THIS GUIDE MAY RESULT IN SERIOUS
INJURY! USING THIS MACHINE WITH RESPECT AND CAUTION WILL
CONSIDERABLY REDUCE THE RISK OF PERSONAL INJURY.
2
520 SEt Up
WELCOME! YOUR MAGNUM RCT SHEAR COMES READY TO ASSEMBLE.
*
*You will need #2 & #3 Phillips head screwdrivers
and a 1/2” (13mm) socket or wrench.
Please Review and Verify Parts Included in Box:
A S S E m b ly
1. ATTACH RAILS
Attach rails to Power Assembly base using Item A
machine screws, fitted with Item B star washers.
2. ATTACH TAIL
Attach tail to rails using Item C machine screws.
Make sure holes in tail are facing up.
F.
5.
1.
1a.
A.
B.
D.
E.
H.
C.
2.
3.
7.
4.
6.
Item A. (4) 6mm x 60mm PH Phillips Machine Screws
Item B. (4) M6 Star Washers
Item C. (4) 6mm x 25mm PH Phillips Machine Screws
Item D. (5) M6 x 16mm FH Phillips Machine Screws
Item E. (4) #10 x 1 FH Phillips Self Tapping Screws
Item F. (2) M8 x 50mm Hex Bolts
Item G. (1) M6 Thumbscrew
HARDWARE KIT:
A.
C.
D.
E.
F.
B.
G.
1. Power Assembly
1a. Safety Lock pin
2. Handle Assembly
3. Table
4. Tail
5. Rails (2)
6. Angle Guide
7. Hone Stone
8. Hardware Kit
1
2
Loading...