Buffalo TeraStation iSCSI, TeraStation TS-ITGL, TeraStation iSCSI TS-ITGL/R5 User Manual
User Manual
TeraStation iSCSI
TS-ITGL/R5
www.buffalotech.com
v1.4
2
Introduction
Congratulations on your new TeraStation! Your TeraStation iSCSI is a huge block of iSCSI
storage, ready to add to your server or PC via ordinary wired Ethernet connections. This
guide will help you congure it.
There are many ways to congure and use iSCSI storage products like the TeraStation. In
this guide we give one example of conguring a simple iSCSI volume on a single workstation.
Many other congurations are usable.
Because we’re constantly updating our product, the images and text in this manual may vary
slightly from the images and text displayed by your TeraStation. These changes are minor
and should not affect the ease of setup adversely. As time passes, future user interfaces,
updated software, and later versions of this manual may be available for download at our
web site: www.buffalotech.com.
If you run into difculties or need additional help, feel free to contact our technical support.
Contact information for Buffalo Technology and our technical support is available on pages
47 and 48.
3
Table of Contents
TeraStation Layout............................................................4
Installation .......................................................................7
Conguration GUI ..........................................................15
Login .......................................................................16
IP Address ...............................................................20
RAID Settings ..........................................................22
UPS ......................................................................... 27
Alerts ....................................................................... 29
Troubleshooting ..............................................................39
Replacing a Hard Drive ................................................... 41
Technical Specications ..................................................46
Technical Support ...........................................................47
GPL Information .............................................................49
4
Layout
Power Switch
Door Lock (Turn counterclockwise to release)
Door opens for access
to hard drives.
Display Mode Switch
5
Hard Drives
(Squeeze tabs to release)
Layout
Init Button returns
settings to factory
defaults.
6
USB in
Layout
Power Cable (to outlet
or surge protector)
UPS
Ethernet (to NIC,
Router, or Switch
7
Insert the TeraNavigator CD into your computer’s CD-ROM drive.
On a PC, setup should automatically launch. If it does not, manually
launch setup.exe by pressing Start and selecting the Run... option.
When the Run dialog opens, type d:\TSnavi.exe (where d is the drive
letter of your CD-ROM drive). Press OK to continue.
Begin by connecting your TeraStation’s power and Ethernet cables. The Ethernet cable should be
connected to an extra NIC on your server or to a router, hub, or switch on your network.
For best performance, all network equipment should be gigabit or better. Use a NIC with enough
RJ-45 ports for all your iSCSI devices, or separate NICs for each iSCSI device. Assign static IP
addresses for each iSCSI device. Bridge the ports for all the NICs in the server (including the LAN
connection). Statically assign the IP address for the LAN to the “Bridged” connection, not on the
actual NIC for the LAN. Provided uninterruptable power supplies for all iSCSI devices, as well
as the server itself. Simpler congurations may work, but this kind of uncompromising setup is
recommended for best performance and reliability.
After all connections are made, turn the TeraStation on by pushing the power button on the front
panel. It will take about a minute to boot.
Installation
8
Press the Begin Installation button to begin.
Easy Setup will step you through physically connecting your
TeraStation. It will then install software.
Advanced Setup skips the connection tutorial and goes
directly to installing software.
Installation
9
If your TeraStation is connected correctly when you get
to this window, it will be highlighted in the drop-down
list. If you have multiple units to set up, select the correct
TeraStation from the list.
Select First Setup for the initial installation.
To install the software on additional computers, chose
Additional Setup.
Installation
10
Once the TeraStation is installed, you’ll need to install
the iSCSI connection tool. Click Next, then continue to
click Next, stepping through the menus until the iSCSI
connection tool is installed.
Click Yes to launch the iSCSI connection tool.
Installation
11
If the TeraStation has more than one volume, choose
the volume you want to connect to from the drop
down list. Check Resume connection at start up.
Click Connect. Repeat to add additional volumes if
desired.
Installation
Make sure that your ISCSI TeraStation is selected in the
Target product window. Click Register the iSCSI Hard Disk,
and then OK.
12
Installation
If Disk Management does not open automatically, you may launch
it manually. From the Setup menu at the top of the window,
choose Launch Disk Management.
Each connected volume from your ISCSI TeraStation now
appears as a hard drive in Disk Management.
13
Installation
The Initialize and Convert Disk Wizard will
open. Use it to convert your new volumes
to dynamic volumes. Put a checkmark next
to each of your disks and click Next to step
through the menu.
Right-click on the volume in Disk Management
and click New Volume to start the New Volume
Wizard. Click Next.
14
Choose your desired volume type. Use Simple if
you have only one volume to mount. Spanned and
Striped volumes require multiple disk volumes to
create. Click Next when ready.
Add all dynamic disks that will be included in the
volume to the Selected column by highlighting them
and then clicking the Add button.
Installation
15
Installation
Choose your desired drive letter. Click Next.
Choose your desired format and volume label. Click Next.
Your new volume is installed and ready to use!
Loading...