How it Works
Buffalo
Loading...
TeraStation 5000
User Manual
181 pgs7.07 Mb0
User manual [de]
194 pgs7.79 Mb0
Table of contents
Loading...

Buffalo TeraStation 5000 User Manual

TeraStation 5000
User Manual
www.buffalotech.com
35020018-04
2014-01
Contents
Chapter 1 Installation ......................................................10
For Initializing Settings ................................................................................19
For Resetting Password ................................................................................19
Chapter 2 Configuration .................................................21
Chapter 3 Access Restrictions .........................................25
Adding a Shared Folder ................................................................................25
Adding Users .................................................................................................27
Adding Groups ..............................................................................................28
Access Restrictions ........................................................................................29
2
Chapter 4 Managing Your Storage .................................38
Using JBOD ....................................................................................................40
Changing RAID Mode ...................................................................................40
Configuring a Hot Spare ...............................................................................41
RMM (RAID Mode Manager) .........................................................................42
RAID Scanning...............................................................................................44
Quotas for Users ............................................................................................52
Quotas for Groups ........................................................................................52
Size Limits ......................................................................................................53
Introduction ..................................................................................................55
Using the iSCSI Connection Tool ..................................................................59
Creating and Expanding Volumes ...............................................................62
Disconnecting Volumes ................................................................................63
Setting Access Restrictions ..........................................................................64
3
Hard Drive Replacement Examples .............................................................67
Chapter 5 Backup ............................................................74
Preparing a Backup Destination ..................................................................74
Configuring a Backup Job ............................................................................75
Ethernet Cable Connection Methods ..........................................................80
Configuring Failover .....................................................................................82
Chapter 6 Remote Access ................................................89
Configuration ................................................................................................89
Chapter 7 BitTorrent ........................................................94
4
Chapter 8 Multimedia .....................................................96
Configuration ................................................................................................96
Playing Files ..................................................................................................97
Connected DLNA-compatible Devices ........................................................97
Streaming to DLNA-compatible Devices ....................................................98
Disabling Playback from Specific Devices ..................................................99
iTunes Server ................................................................................... 100
Squeezebox Server ......................................................................... 101
Chapter 9 Surveillance Server ......................................103
Getting Started ............................................................................... 103
Installing Client Tools ................................................................................ 103
Connecting Devices to the Network ......................................................... 104
Enabling Surveillance Cameras ................................................................ 104
Enabling the Free License ......................................................................... 106
Registering Recording Policies ................................................................. 108
Checking Recording ................................................................................... 111
Email Error Notification ............................................................................. 112
Configuration .................................................................................. 112
Viewing Saved Video ................................................................................. 112
Export Recorded Data as a MOV Video File ............................................. 113
Viewing Video Real-time ........................................................................... 115
Moving Recorded Video Data to Another TeraStation ............................ 115
Backing Up Recorded Video to Another TeraStation .............................. 116
Automatically Delete Old Data when Space is Low ................................. 117
Changing Where Recorded Video Is Saved .............................................. 119
5
Client Utilities .................................................................................. 119
Camera Policies .......................................................................................... 119
Live Viewer ................................................................................................. 120
Data Service Policies .................................................................................. 121
Vault Admin ................................................................................................ 121
Surveillance Video Manager ..................................................................... 122
Network Activity ........................................................................................ 123
Mini Vault Stats .......................................................................................... 123
Activating Additional Licenses ...................................................... 124
When the TeraStation is Connected to the Internet ................................ 124
TeraStation Not Connected to the Internet ............................................. 126
Troubleshooting .............................................................................. 129
Chapter 10 Advanced Features ....................................130
Antivirus Software .......................................................................... 130
Licenses ...................................................................................................... 130
Activating Virus Scanning ......................................................................... 131
Configuring Security Settings .................................................................. 131
Connecting through a Proxy Server ......................................................... 132
Updating ..................................................................................................... 133
Excluding a Specific Folder from Antivirus Scanning ............................. 134
Virus Scanning ........................................................................................... 134
Checking the Log ....................................................................................... 135
Online Help ................................................................................................. 136
Email Notification ........................................................................... 136
Sleep Mode ...................................................................................... 137
Wake-on-LAN .................................................................................. 139
6
Port Trunking ................................................................................... 141
Connecting a Printer ....................................................................... 142
Setting Up a Printer with Windows 8.1, Windows 8, Windows 7, or
Windows Vista ............................................................................................ 142
Setting Up a Printer with Windows XP ..................................................... 143
TeraSearch ....................................................................................... 144
Offline Files ...................................................................................... 145
DFS ................................................................................................... 147
Accessing from a NFS Client ........................................................... 148
Encrypting Data Transmission ....................................................... 150
Encrypting Settings Data .......................................................................... 150
Encrypting FTP Transfer Data ................................................................... 150
SSL Keys ...................................................................................................... 151
Web Server ....................................................................................... 151
MySQL Server .................................................................................. 152
SNMP ................................................................................................ 153
Saving and Applying Settings ........................................................ 154
Saving Settings .......................................................................................... 154
Applying Settings ...................................................................................... 155
Restoring Factory Defaults ............................................................. 156
Initializing from Settings .......................................................................... 156
Creating an Initialization Drive ................................................................. 156
Initializing with the USB Drive .................................................................. 157
Resetting the Administrator Password ......................................... 157
Creating a Password Reset Drive .............................................................. 157
7
Resetting with the USB Drive .................................................................... 158
Logs .................................................................................................. 158
Updating the Firmware ................................................................... 159
Name, Date, Time, and Language .................................................. 160
Beep Alerts ...................................................................................... 161
LCD and LEDs ................................................................................... 162
Jumbo Frames ................................................................................. 163
Changing the IP Address ................................................................ 164
Chapter 11 Utilities ........................................................166
NAS Navigator2 for Windows ......................................................... 166
Mount as Network Drive............................................................................ 168
Changing the IP Address ........................................................................... 169
NAS Navigator2 for Mac ................................................................. 169
Mount as Network Drive............................................................................ 170
Changing the IP Address ........................................................................... 171
iSCSI Connection Tool ..................................................................... 172
Menu ........................................................................................................... 173
Chapter 12 Appendix ....................................................174
LCD Display ...................................................................................... 174
Modes ......................................................................................................... 174
Errors ........................................................................................................... 174
Status .......................................................................................................... 175
Default Settings .............................................................................. 178
8
Specifications .................................................................................. 178
Compliance Information ................................................................. 179
FCC Statement ............................................................................................ 179
CE Mark Statement .................................................................................... 180
Environmental Information ...................................................................... 180
KC ................................................................................................................ 180
BSMI ............................................................................................................ 180
CCC .............................................................................................................. 180
󰈏
Models ........................................................................................................ 181
9

Chapter 1 Installation

Diagrams

TS5800D
TS5600D
TS5400D
10
TS5200D
TS5400R
1 Power Button
To power on, connect the power cable and wait for 10 seconds, then press the power button. To power off, press the power button twice.
2 Info LED
If there is a status message, the amber info LED will light up. Check the LCD panel to see the status message.
3 Error LED
If there is an error, the red error LED will light up. Check the LCD panel to see the error message.
4 LAN1 LED
When LAN port 1 is connected, this LED glows green. It blinks when the connection is active.
5 LAN2 LED
When LAN port 2 is connected, this LED glows green. It blinks when the connection is active.
6 LCD Panel
This display shows the status of many TeraStation settings. It also displays errors and messages when available.
7 Display Button
Switches between the different display modes. Also, if the TeraStation is beeping, press this button to stop it.
8 Function Button
Use this button for Direct Copy, dismounting USB devices, rebuilding RAID arrays, and configuring failover.
9 Drive Lock
Open the front panel with the key to replace hard drives or access the reset button.
11
10 Reset Button
To shut down and reboot the TeraStation, hold down the reset button.
11 Status LEDs
Normally, these LEDs blink green when hard drives are accessed. If a drive fails, its LED will turn red or amber.
12 Factory Use Only
13 Boot Mode Switch
Leave the switch in the HDD position during normal operation. To recover settings, insert the recovery USB drive into a USB 2.0 port, move the boot switch to the USB position, and press the power button.
14 UPS Port
Connect to a UPS.
15 USB 3.0 Port
Compatible Buffalo USB 3.0 hard drives can be connected. USB hubs are not supported.
16 USB 2.0 Port
Compatible Buffalo USB hard drives, USB flash drives, digital cameras, and USB UPS connection can be connected. USB hubs are not supported.
17 LAN Port 1
Use an Ethernet cable to connect this port to your network.
18 LAN Port 2
This second Ethernet port may be used for network redundancy or backup. You may connect a second TeraStation directly to this port for backup.
19 Power Connector
Use the included power cable to connect to an UPS, surge protector, or outlet.
20 Fan
Do not block the fan.
21 Anti-Theft Security Slot
Use this slot to secure your TeraStation with a cable lock (not included).
22 UID Button
Press the UID button on the front or the back of the unit to cycle the blue LED on and off.
23 Serial Number
This sticker shows the TeraStation’s serial number.
24 Link LED
Glows orange when the unit is connected to a network.
25 Act LED
This LED shows network activity. It blinks orange when the TeraStation is accessed over the network.
12

Installation

1 Insert the TeraNavigator CD into your computer. TeraNavigator will launch.
2 Click Begin Installation.
3 Follow the steps on the screen to connect the TeraStation’s Ethernet and power cables and turn it on.
Note: Use LAN port 1 for initial setup. After setup, you may connect a second cable to LAN port 2. If you use LAN port 2, configure the IP address at Network - IP Address in Settings.
4 Follow the steps on the screen to install NAS Navigator2.
5 Click Finish. NAS Navigator2 will open.
6 Right-click on your TeraStation’s icon and choose Properties.
Note: For Mac OS, select the TeraStation’s icon while holding down the control key, then click Configure.
7 Click the IP Address tab, enter the desired settings, and click OK.
13
If you are prompted to enter the administrator password for the TeraStation, it is “password” by default.
8 Right-click on your TeraStation’s icon and choose Settings.
9 Changing the password from the default is recommended.
10 Go to Management - Name/Time/Language and configure the TeraStation’s time and date.
14
Notes:
• For best results, use an NTP server to maintain the time settings on the TeraStation and other network devices. Clocks for the network devices may run at slightly different speeds. If these devices get out of sync it may cause network problems.
• Buffalo is not responsible for any losses and damages incurred from using the ntp.jst.mfeed.ad.jp service or ser­vice outages.
• If the TeraStation cannot automatically obtain the time from an NTP server, check its DNS settings. If the NTP server is specified by a hostname instead of an IP address, make sure that a DNS server address is configured in Network - IP Address.
11 In NAS Navigator2, double-click your TeraStation’s icon. This will open the shared folder of the TeraStation. For Mac
OS, the TeraStation is mounted as a drive icon on the desktop or it is displayed in the sidebar of the Finder. You can now use the TeraStation’s shared folder to save files just like any other folder.

Turning the TeraStation On and Off

Press the power button on the TeraStation to turn it on.
To turn off the TeraStation, press the power button twice. Don’t unplug the TeraStation without turning it off first. You can also shut it down and restart it remotely from Settings.
15
Shutdown or Restart from Settings
1 Double-click the icon.
2 Right-click your TeraStation’s icon and select Settings. For Mac OS, select the TeraStation’s icon while holding down
the control key, then select Settings.
3 Enter the username and password, then click OK.
Note: The default username and password are “admin” and “password”.
4 Settings will open.
16
5 Click at the top-right of Settings and choose either Restart or Shut Down.
When all the LEDs on the front of the TeraStation turn off, the shutdown process is complete.

Changing the Administrator Password

After initial setup, follow this procedure to change your password.
1 Double-click the icon. NAS Navigator2 will start.
2 Right-click on your TeraStation’s icon and select Settings. On the Mac, select the TeraStation’s icon while holding
down the control key, then select Settings.
17
3 Click Easy Admin.
4 Click Change Password.
5 If this screen is displayed, enter the current password and click OK. The default password is “password”.
6 Enter the new password (twice).
18
7 Click OK. You have changed the admin password.

Recovery Drive

To initialize all of the TeraStation’s settings, or just restore the admin password to its factory default value, create the recovery drives as described below.

For Initializing Settings

A system initialization drive can reset all settings to their default values.
Notes:
• Normally, making and using the system initialization drive will not affect data. However, always back up your data regularly!
• This USB drive can be used to recover the system if your TeraStation doesn’t boot at all. In this case, if the data partition is damaged, then all your data will be deleted by the recovery process.
1 Insert a 1 GB or larger USB flash drive into a USB port on the TeraStation.
Note: All data on the USB flash drive will be erased!
2 In Settings, navigate to Management-Restore/Erase-USB Options.
3 Select Create a USB drive for initializing settings.
4 Select the USB memory device from “Target USB drive”, then click Execute.
5 Enter the 4 digit confirmation number and click OK. The TeraStation will create the initialization drive. This will take
about a minute.
6 When the “finished” dialog opens, the USB initialization drive is ready to use. Dismount the USB drive before
unplugging it. See “Dismounting Drives” in chapter 4 for the instructions on dismounting drives.

For Resetting Password

A password initialization drive can reset the administrator password to its default value (“password”). This could be very
19
useful if you forget your admin password.
1 Insert a 1 GB or larger USB memory device (not included) to a USB 2.0 port on the TeraStation.
Note: All data on the USB flash drive will be erased!
2 In Settings, navigate to Management - Restore/Erase - USB Options.
3 Select Create a USB drive for resetting the admin password.
4 Select the USB memory device from “Target USB drive” list, then click Execute.
5 Enter the 4 digit confirmation number and click OK. The TeraStation will create the password reset drive. This will
take about a minute.
6 When the “finished” dialog opens, the password reset drive is ready to use. Dismount the USB drive before
unplugging it. See “Dismounting Drives” in chapter 4 for the instructions on dismounting drives.
For instructions on using system initialization or password initialization drives, see chapter 10.
20

Chapter 2 Configuration

Configure and administer your TeraStation using the Settings interface, accessible from a browser window. Open the interface using the procedure below or type the TeraStation’s IP address in the URL field of your browser. Within Settings, the Easy Admin page gives you quick access to commonly used settings.
Note: Internet Explorer 9, Firefox 18, Google Chrome 24, Safari 5, and later are supported. If you have difficulty viewing Settings, check the following:
• If there are a large number of registered users, groups, or shared folders, use Firefox instead of Internet Explorer.
• If you have a proxy server enabled in the browser settings, disable the proxy server.
• With Internet Explorer, set security to Local intranet. On Windows Server 2008, higher-level security is configured by default. Set the security to a lower level temporarily.

Opening Settings

1 Open NAS Navigator2 by double-clicking the icon.
2 Right-click on your TeraStation’s icon in NAS Navigator and select Settings. For Mac OS, click your TeraStation’s icon
while holding down the control key, then select Settings.
3 Enter the username and password and click OK.
21
Username/Password Combinations:
Username Password Settings Available admin password All
guest blank
your username your password
Notes:
• If the time-out period is set to “10 minutes”, you will be logged out of Settings after 10 minutes of inactivity.
• Click Secure Connection to log in with an encrypted connection.
TeraStation name, IP address, workgroup, drive status, hardware version
TeraStation’s name, IP address, workgroup, drive status, firmware version, and your password.
4 Settings will open.
Notes:
• Click to open Easy Admin.
• Click to play a tone from the TeraStation for easy location.
• You can also use Bonjour to log in to Settings from OS X 10.4 or later. In Safari, click View - Show Bookmarks Bar. From Bookmarks, click Bonjour - TeraStation name.
22

Opening Easy Admin

The Easy Admin page makes it easy to change common settings. Follow the steps below to open Easy Admin.
1 Open NAS Navigator2 by double-clicking the icon.
2 Right-click on your TeraStation’s icon and choose Settings. For Mac OS, click the TeraStation icon while holding
down the control key, then select Settings.
3 Click Easy Admin.
4 The Easy Admin screen will open.
23
Notes:
• If you click any buttons , you will need to enter a username and password.
• You can open Easy Admin anytime by clicking the icon at the top left of Settings.
24

Chapter 3 Access Restrictions

You may restrict access to specific shared folders, including external USB drives.
Notes:
• Access restrictions can be set separately for each shared folder, but not for folders within the shared folders.
• Configure access restrictions through Settings. Configuring access restrictions through Windows is not supported and may cause unexpected behavior.
• You can also configure users, groups, and shared folders from Easy Admin by clicking Access Restrictions.
• Shared folders with limited access can still be used as backup destinations.
• If you change access restrictions for a user or group while they are accessing files, unexpected behavior may result.

Configuring Access Restrictions for Users and Groups

Adding a Shared Folder

1 In Settings, click the icon to the right of “Folder Setup”.
2 Click Create Folder.
3 Configure the settings, then click OK.
25
Notes:
• Names may contain up to 27 alphanumeric characters, hyphens (-), and underscores (_). Do not use a symbol as the first character in a name.
• The description may contain up to 75 alphanumeric characters, hyphens (-), underscores (_), and spaces. Do not use a symbol or space as the first character.
• You may create up to 400 shared folders.
• The names of shared folders should not use characters from more than one language. For example, mixing Japa­nese and Korean characters in names is not supported.
• If multi-byte characters are used in shared folder names, configure the client language to match the characters in Management - Name/Time/Language.
Recycle Bin
To protect your data from accidental deletion, you may configure your TeraStation to use a recycle bin instead of deleting files immediately. The recycle bin will only work with SMB connections. To empty the recycle bin, click File Sharing - Folder Setup - Empty Recycle Bin in Settings.
Notes:
• You can prevent guests and other users from emptying the trash by navigating to File Sharing - SMB - Permissions for Trashbox and selecting “Administrator only”.
• If you use Mac OS, make sure that your recycle bin enables “Exclude Mac OS temp files from recycle bin”. If this setting is changed, files in the recycle bin may be corrupted.
26
Accounts
Your TeraStation username and password should be the same as your Windows username and password. If they are different, you may not be able to access folders on the TeraStation with access restrictions configured.
Read-only Shares
By default, new shares are set with read & write access, but you may change the attribute to Read-only in Shared Folder Attributes. Read-only shares and HFS+ formatted USB hard drives will have “Read-only” added to the shared folder
description.
Hidden Shares
To hide a shared SMB folder, select “Hidden Share (SMB Only)” and click OK. To open a hidden folder, click Start - Search programs and files and enter “\\TeraStation name\Shared folder name$\” for the name. Example: If the TeraStation name
is “TS-XX001” and the shared folder name is “share”, then enter “\\TS-XX001\share$\” to open it.
Note: FTP, SFTP, and AFP folders cannot be hidden.

Adding Users

1 In “File Sharing”, select Users.
2 Click Create User.
3 Enter the desired settings, then click OK.
Notes:
• Usernames may contain up to 128 characters, including hyphens (-), underscores (_), periods (.), !, #, &, @, $, *, ^, and %. Do not use a symbol as the first character.
27
• For Windows 8.1 and Windows 8, use a local username instead of your Windows Live ID.
• The user ID should be a number from 1000 to 1999. Each user ID should be unique. If this field is left blank, a user ID is assigned automatically.
• Do not duplicate user IDs, group IDs, usernames, or group names. Each should be distinct and unique.
• The description may contain up to 75 alphanumeric characters, hyphens (-), underscores (_), and spaces. Do not use a symbol or space as the first character.
• When setting users with access privileges, a maximum of 300 users, including “admin” and “guest”, can be regis­tered in the TeraStation.
• Passwords may contain up to 20 alphanumeric characters and the following characters: - _ @ ! # $ % & ‘ ( ) * + , . / ; < > = ? “ [ ] ^ { } | ~. Do not use a symbol other than an underscore (_) as the first character.
• Use the same username and password for both Windows and the TeraStation or you may not be able to access shared folders.
Importing User Information
You can import users in File Sharing - Users by clicking Import CSV File. Existing users will be overwritten.
Format for user data: Username (required), password (required), and user description (optional).
Examples:
username1,password1,comment1
username2,password2,comment2
username3,password3,comment3
Guidelines:
• Use commas (,) as separators. Do not put spaces before or after commas.
• If a line has an incorrect format, the user on that line will not be registered.
• If a username exists, the new user information will overwrite the old information.
• Do not use commas (,) in the username, password, or user description.
Note: Imported users are added to the “hdusers” group automatically.
Shared Folder Owners
To confirm the owner of a shared folder from Windows XP, from the Properties screen of the file or folder, open a new window from the Security tab. Click Advanced, then click the Owner tab.

Adding Groups

1 In “File Sharing”, select Groups.
2 Click Add Group.
3 Enter settings, then click OK.
28
Notes:
• Group names may contain up to 20 alphanumeric characters, hyphens (-), underscores (_), and periods (.). Do not use a symbol other than an underscore (_) as the first character.
• Group descriptions may contain up to 75 alphanumeric characters, hyphens (-), underscores (_), and spaces. Do not use a symbol or space as the first character.
• If the group ID field is left blank, a group ID is automatically assigned. Use numbers between 1000 and 1999 to set a group ID manually. Don’t use duplicate group IDs.
• You may register up to 300 groups with the TeraStation.
• If you are logged in as a member of the general users group, you can only change your own password. If you’re logged in as an administrator, you can change any settings, including other users’ passwords. If you are logged in as a member of the power users group, you can create and edit shared folders, users, and groups.

Access Restrictions

1 In “File Sharing”, select Folder Setup.
2 Click the shared folder that you want to set access restrictions for.
29
3 Click Edit.
4 Enable “Access Restrictions”.
5 Select the level of access for the user or group you added.
: Read and write access allowed : Read access allowed : Access prohibited
6 Click OK.
Notes
• The example above shows access restriction by user. To restrict access by group, click the Local Groups tab and select group permissions.
• If both read-only and read & write permissions are given to a user, the user will have read-only access. The most restrictive access always applies.
• The following characters are handled differently by Mac OS and Windows. Avoid using these characters when sharing data between Mac OS and Windows:
• Windows does not support some characters that Mac OS and the TeraStation allow. If you create a filename on a Mac with any of the following characters, it will not display correctly on a Windows computer. With OS X 10.2 or later, you may have to connect to the TeraStation via AFP in order to display or copy any of the following characters.
? [ ] / \ = + < > ; : “ , | *
• Do not use any of the following words as a username or group name: root, bin, daemon, sys, adm, tty, disk, lp, sync, shutdown, halt, operator, nobody, mail, news, uucp, ftp, kmem, utmp, shadow, users, nogroup, all, none, hdusers, admin, guest, man, www, sshd, administrator, ftpuser, apache, mysql
• Do not use any of the following words as the name of a shared folder. These words are reserved for internal use by
30
Loading...
+ 151 hidden pages
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use