BT SPEEDWAY ISDN TA User Manual

IMPORTANT

Please read this guide before attempting to install your TA

Windows 2000

Speedway
ISDN TA

USB Software Installation Guide

1

Introduction

Follow the instructions contained within the Speedway ISDN TA installation guide
up to the section, Installing the Speedway ISDN TA software. Then proceed with
the installation by following the instructions contained in this supplement.

Installing the Speedway ISDN TA software
Installing the Speedway ISDN TA software using the Windows 2000 USB

connection

Ensure no windows applications are running.

Connect the USB cable to the PC that has been previously attached to your TA.

Windows 2000 will detect the TA (If this does not happen refer to the ‘Trouble
shooting’ section at the end of this supplement.) A Found New Hardware window
will show that a USB ISDN-Connector has been detected, please wait whilst the PC
prepares for the next stage of installation.

The Found New Hardware Wizard appears and displays that it is going to help
install the drivers for your hardware.

Click Next.

Insert the Speedway CD ROM. (If the Welcome to BT Speedway TA screen is
displayed, please close this screen.)

In the next Window (shown below) the wizard details the device to be installed
USB ISDN-Connector, under the question What do you want the wizard to do?
select the option Search for a suitable driver for my device.

2

Click Next

In the next Window (shown below) tick only the Specify a location option.

Click Next

At the next window (shown below) either enter (your CD drive):\windows.2k into
the Copy Manufacturer’s files from: input box, or use the Browse button to bring
up a browse window (shown below) and open the Windows.2k folder found on the
Speedway CD ROM.

3

Click Open

Click OK

Windows now searches for drivers for the new hardware, this may take a few
minutes. Wait until it displays the correct location of the drivers, (your CD
drive):\windows.2k\speedta.inf.

Click Next

The next window (shown below) appears, this is a Digital Signature not found
window.

Click Yes

Windows then copies the files to the system

The next window confirms the system has finished installing the drivers.

Click Finish

Eject and re-insert the Speedway CD ROM. The CD should automatically load and
you should see the Welcome screen (shown below). If the CD does not
automatically load use Windows Explorer (or Start menu/Run…) to open the
intro.hlp file on the Speedway CD ROM.

4

Click on the BT icon.

The next screen (shown below) shows the operating systems under which the
Speedway ISDN TA can be installed.

Click on the Microsoft Windows 2000 button.

5

Click on the Install button.

The installation for Speedway! Applications program will now start and the BT
Speedway Welcome screen is displayed. It is best to follow the on-screen
instructions that are now displayed, but you may find it easier to refer to the
section: Installing the Speedway! Applications contained in the Speedway ISDN
TA installation guide.

The next screen (shown below) provides instructions on how to install the device.

6

Troubleshooting & Support

Problem: Found New Hardware Wizard does not start when installing USB device.

If the hardware wizard fails to start check the following:
Make sure the ‘Universal Serial Bus controller’ is installed in your Windows

system. This can be checked by opening the Control Panel (Start – Settings ­Control Panel). Double-Click on the System icon, click on Hardware tab, click on
Device Manager button and scroll down list. The ‘Universal Serial Bus controller’
should be shown in the device list. If this is not available refer to your Windows
manual in order to install new components.

Hints & Tips

It is a good idea to view the Readme file on the CD for the latest

product information and installation advice.

Offices worldwide

Windows is a registered trademark of Microsoft Corporation.
Adobe and Acrobat are trademarks of Adobe Systems, Inc

Speedway and Speedway! are trademarks of British Telecommunications plc.

Touchtone

TM

is a registered trade mark of

British Telecommunications plc in the UK.

© British Telecommunications plc 2000.
Registered Office: 81 Newgate Street, London EC1A 7AJ.
Registered in England No. 1800000.
Speedway USB (Windows 2000) (7/00) 6
Designed by The Art & Design Par tnership Limited.
Printed in Germany.

Printed on paper which meets international environmental standards.

CE compliant to 89/336/EEC
(EMC Directive) & 73/23/EEC
(Low Voltage Directive)