Bryant 597C User Manual

ELECTRIC
AIR CONDITIONER

The Reliant
tures to achieve ultra-low sound ratings.

Aerocoustic Design featuring the Aeromax opening and wire

dome top results in quieter and more efficient operation.

Energy-Efficient Fan and Fan Motor provide a slower fan

motor, reducing noise and improving efficiency.

Advanced Sound Hood to muffle noise from operation.

Model 597C Energy-Efficient Air Conditioners incorporate inno­vative scroll compressor technology to provide quiet, reliable
cooling performance. Built into these units are the features most
desired by homeowners today including SEER ratings up to 14.0
when combined with specific Bryant equipment. All models are
listed with UL, c-UL, ARI, CEC, and CSA-EEV. The 597C meets
the Energy Star

AeroQuiet System (AQS)

®

guidelines for energy efficiency.

consists of 3 design fea-

597C (60 Hz)

Sizes 018 thru 060

AVAILABLE OPTIONS

DURAGUARD™ COIL PROTECTION —Made of a coated steel

wire grid with vertical 3/8 in. spacing, is designed to help protect
the coil from inclement weather, vandalism, and incidental hits.
It provides protection while not restricting airflow and maintain­ing ease of coil inspection and cleaning.

ELECTRICAL RANGE —All units are offered in 208/230-v sin-

gle phase only.

WIDE RANGE OF SIZES —Available in 7 nominal sizes from

018 through 060 to meet the needs of residential and light com­mercial applications.

WEATHER-PROTECTIVE CABINET —Steel is galvanized and

coated with a layer of zinc phosphate. A coat of modified poly­ester powder is then applied and baked on, providing each unit
with a durable finish that will last for many years.

All screws on cabinet exterior are coated for a long-lasting, rust­resistant, quality appearance.

TO TALLY ENCLOSED FAN MOTOR —Provides greater reliabil-

ity under adverse weather conditions and dependable perfor­mance for many years. The permanent-split-capacitor type
motor was designed for optimum efficiency. Then, under
extreme conditions, the motor was tested and qualified to help
ensure the greatest reliability.

UNIT DESIGN —Copper tube, enhanced aluminum fin coil is

designed for optimum heat transfer. Vertical air discharge car­ries sound and hot condenser air up and away from adjacent
patio areas and foliage. Heat pump style base pan for easy
removal of water, dirt, and leaves.

APPLICATION VERSATILITY —The 597C can be combined

with a wide variety of evaporator coils and blower packages to
provide quiet, dependable comfort. Unit can be installed on a
roof or at ground level on a slab.

EXTERNAL SERVICE VALVES —Both service valves are

brass, back seating type with sweat connections. Valves are
externally located so refrigerant tube connections can be made
quickly and easily. Each valve has a service port for ease of
checking operating refrigerant pressures.

EASY SERVICEABILITY —One access panel provides access

to electrical controls and compressor. Removal of wire dome
gives access to fan motor and removal of the top gives access
to the coil.

COMPRESSOR PROTECTION —Each scroll compressor

motor is protected with internal temperature and current-sensi­tive overloads. For improved serviceability, each compressor is
equipped with a compressor terminal plug.

SOUND HOOD —A thick, sound dampening material wrapped

around the compressor muffles operational noise.

LIMITED WARRANTY —Standard 1-year warranty on parts,

with an additional 9-year warranty on compressor.

Form No. PDS 597C.18.8

DIMENSIONS

A97082

B

ACCESS

DIA

/8-IN.

7

DIA KNOCKOUT

/8-IN.

1

DIA KNOCKOUT

/8-IN.

3

FIELD POWER SUPPLY CONN

AND 1

HOLE WITH 1

FIELD CONTROL

SUPPLY CONN

"

"

/16

/2

9

1

1

2

C

PANEL

A

DIA HOLE

DIA VAPOR

LINE CONN

H

/8-IN.

7





G

F

DIA LIQUID

/8-IN.

3

LINE CONN

PAD DIMENSIONSABCDEFGHKLMN

MINIMUM MOUNTING

"

/4

1

1



M

"

/2

1

10

"

/16

3

4

"

/4

3

1

N

AIR DISCHARGE

DIA TIEDOWN KNOCKOUTS

/8-IN.

3

(2) PLACES IN BASEPAN

clearance to service end of unit, 48 in. above unit, 6 in. on one side, 12 in. on remaining side,

and 24 in. between units for proper airflow.

Minimum outdoor operating ambient in cooling mode is 55°F (unless low-ambient control is used) max 125°F.2.

Series designation is the 14th position of the unit model number.3.

1. Allow 30 in.

Center of gravity .4.

AIR IN

L

K

D

E

L

C

"

/16

3

8

AIR IN

NOTES:

AIR DISCHARGE

AIR IN

AIR DISCHARGE

UNIT DIMENSIONS

DIMENSIONS (IN.)

—2—

SIZE SERIES

UNIT

018 F 33-13/16 22-1/2 26-3/16 4-1/8 7-1/8 21-15/16 28-3/8 5/8 9-1/4 17-3/8 13-1/2 2-3/8 20 x 27

024 F 27-13/16 30 33 5-1/16 9-11/16 15-15/16 22-3/8 5/8 16-1/2 20-3/8 11 2-15/16 26 x 32

030 F 33-13/16 30 33 5-1/16 9-11/16 21-15/16 28-3/8 3/4 16-1/2 20-3/8 13-1/2 2-15/16 26 x 32

036 F 33-13/16 30 33 5-1/16 9-11/16 21-15/16 28-3/8 3/4 16-1/2 20-3/8 13-1/2 2-15/16 26 x 32

042 F 39-13/16 30 33 5-1/16 9-11/16 27-15/16 34-3/8 7/8 16-1/2 20-3/8 15 2-15/16 26 x 32

048 G,F 39-13/16 30 33 5-1/16 9-11/16 27-15/16 34-3/8 7/8 16-1/2 20-3/8 15 2-15/16 26 x 32

060 F 39-13/16 30 33 5-1/16 9-11/16 27-15/16 34-3/8 7/8 16-1/2 20-3/8 15 2-15/16 26 x 32

*

*

*

*

RECOMMENDED TUBE DIAMETERS

Liquid Tube Diameter (In.) Vapor Tube Diameter (In.)

UNIT
SIZE

018, 024
030, 036 3/4 7/8
042, 048 7/8 1-1/8

0 to 50 Ft

Tube Length Long-Line Applications

3/8 3/8

0 to 50 Ft

Tube Length

Long-Line Applications *

(Maximum Diameter)

5/8 3/4

060 1-1/8 1-1/8

For tube sets between 50 and 175 ft, consult Residential Split System Long-Line Application Guideline.

CHECK-FLO-RATER® PISTON

UNIT SIZE-SERIES

018-F 55
024-F 61
030-F 67
036-F 76
042-F 82
048-G 90
048-F 93
060-F 101

Piston listed is for any approv ed non-capillary tube coil combination. Piston
is shipped with outdoor unit and must be installed in an approved indoor
coil.

PISTON

IDENTIFICATION NO.

CHARGING SUBCOOLING (TXV-TYPE EXPANSION DEVICE)

UNIT SIZE-SERIES REQUIRED SUBCOOLING (°F)

018-F 10
024-F 12
030-F 15
036-F 12
042-F 12

048-G,F 11

060-F 12

T

O

D

E

A

I

R

F

I

I

T

A

R

S

E

C

O

A

M

I

R

C

P

O

Y

R

A

T

I

I

S

L

N

D

Y

I

T

I

N

I

O

G

N

I

N

W

G

I

T

E

T

H

T

Q

N

U

E

I

P

M

0

1

2

D

A

R

N

A

D

REGISTERED QUALITY SYSTEM

As an ENERGY STAR®
Partner, Bryant Heating
& Cooling Systems has
determined that this
product meets the
ENERGY STAR®
guidelines for energy
efficiency.

C

R

E

R

U

T

C

N

A

U

F

U

N

A

M

A

R

CERTIFICATION APPLIES

ONL Y WHEN THE

COMPLETE SYSTEM

IS LISTED WITH ARI.

—3—

*

**

SPECIFICATIONS

UNIT SIZE-SERIES 018-F 024-F 030-F 036-F 042-F 048-G/F 060-F

Operating Weight (Lb) 149 187 197 197 207 261 265

ELECTRICAL

Unit Volts—Hertz—Phase 208/230—60—1 208/230—60—1 208/230—60—1 208/230—60—1 208/230—60—1 208/230—1—60 208/230—1—60
Operating Voltage Range
Compressor— Rated Load Amps 10.0 11.4 15.0 17.9 20.0 23.7/19.9 28.8

Locked Rotor Amps 41.0 56.0 72.5 88.0 104.0 129.0/137.0 169.0
Condenser Fan Motor—Full Load Amps 0.5 0.5 0.5 1.1 1.1 1.1 1.4
Min Unit Ampacity for Wire Sizing 13.0 14.8 19.3 23.4 26.0 30.5/26.0 37.4
Min Wire Size (60°C Copper) AWG† 14 14 14 12 10 8/10 8
Min Wire Size (75°C Copper) AWG† 14 14 14 12 10 10 8
Max Wire Length (60°C) (Ft)‡ 61 53 39 52 77 77 82
Max Wire Length (75°C) (Ft)‡ 58 50 37 50 73 61 78
Max Branch Circuit Fuse Size (Amps)

COMPRESSOR & REFRIGERANT

Compressor— Manufacturer Copeland

Type Scroll
Temperature & Current Protection Internal Line Break
Refrigerant— Type R-22

Amount @ 15 Ft †† 4.25 5.25 6.25 6.25 7.00 10.50 11.00

CONDENSER COIL & FAN

Coil Face Area (Sq Ft) 10.9 12.2 15.2 15.2 18.3 18.3 18.3
Fins Per In.—Rows—Circuits 25—1—2 25—1—2 25—1—3 25—1—3 25—1—4 20—2—5 20—2—6
Fan Motor—PSC Type, HP & RPM 1/15 & 800 1/5 & 825 1/4 & 1125

Volts—Hertz—Phase 208/230—60—1

Condenser Airflow (CFM) 1500 2000 2000 3000 3000 3000 3300

OPTIONAL EQUIPMENT

Support Feet KSASF0101AAA
Coastal Filter KAACF0101SML KAACF0201MED

Time Delay Relay KAA TD0101TDR
Cycle Protector KSACY0101AAA
Crankcase Heater KAACH1201AAA
Start Assist—Capacitor/Relay Type KSAHS1501AAA
Start Assist—PTC Type KAACS0201PTC
TXV (RPB) KAATX0201RPB KAATX0301RPB KAATX0401RPB KAA TX0501RPB KAA TX0601RPB KAA TX0701RPB
TXV (Hard Shutoff)‡‡ KSATX0601HSO KSATX0701HSO
Low-Pressure Switch KAALP0101LPS
High-Pressure Switch KSAHI0101HPS
Filter Drier P502-8083S (RCD) P502-8163S (RCD)
Evaporator Freeze Thermostat
Liquid-Line Solenoid Valve KAALS0101LLS
Winter Start Control
Low-Ambient Pressure Switch KSALA0201R22
Low-Ambient Controller P251-0083 (RCD)
MotorMaster® Control††† 32LT660004 (RCD)

Ball Bearing Fan Motor Not Available HC38GE231 (RCD)
Thermostat, Auto Changeover,

Non-Programmable, °F/°C,
1-Stage Heat, 1-Stage Cool TSTATBBNAC01-B

Thermostat, Auto Changeover,

7-Day Programmable, °F/°C,
1-Stage Heat, 1-Stage Cool TSTATBBPAC01-B

Thermidistat™ Control—

Programmable/ Non-Programmable Thermostat
with Humidity Control TSTATBBPRH01-B

Builder’s Thermostat, Manual Changeover,

Non-Programmable, °F/°C,

1-Stage Heat, 1-Stage Cool TSTATBBBAC01-B
Outdoor Air Temperature Sensor TSTATXXSEN01-B
Backplate for Builder’s Thermostat TSTATXXBBP01
Backplate for Non-Programmable Thermostat TSTATXXNBP01
Backplate for Programmable Thermostat TSTATXXPBP01
Thermostat Conversion Kit (4 to 5 wire) TSTATXXCNV10

***

***

See notes on page 5.

187—253 187—253 187—253 187—253 187—253 187—253 187—253

20 20 30 40 40 50/40 60

KSAHS1601AAA

KAAFT0101AAA

KAAWS0101AAA

HC40GE232

(RCD)

—4—

*

**

Permissible limits of the voltage range at which the unit will operate satisfactorily. Operation outside these limits may result in unit failure.

† If wire is applied at ambient greater than 30°C (86°F), consult Table 310-16 of the NEC (ANSI/NFPA 70).

The ampacity of nonmetallic-sheathed cable (NM), trade name ROMEX, shall be that of 60°C (140°F) conductors, per the NEC (ANSI/NFPA 70) Article
336-26. If other than uncoated (non-plated), 60 or 75°C (140 or 167°F) insulation, copper wire (solid wire for 10 AWG and smaller, stranded wire for larger
than 10 AWG) is used, consult applicable tables of the NEC (ANSI/NFPA 70).

‡ Length shown is as measured 1 way along wire path between unit and service panel for a voltage drop not to exceed 2%.

Time-delay fuse or circuit breaker.
†† Charge quantity is for 15 ft of interconnecting tubing. For tubing lengths longer than 15 ft, add 0.6 oz of refrigerant per ft of tube length in excess of 15 ft.
‡‡ Do not use hard shutoff TXV with LSV.

*** See low-ambient controller Installation Instructions for application.

††† Fan motor with ball bearings required.

NOTES: 1. All motors/compressors contain internal overload protection.

2. Copper wire must be used from service disconnect to unit.

3. Control circuit is 24v on all units and requires external power source.

—5—

*

1.

*

ACCESSORY USAGE GUIDELINE

REQUIRED FOR

LOW-AMBIENT

ACCESSORY

Crankcase Heater Yes Yes No

Evaporator Freeze Thermostat Yes No No

Winter Start Control Yes† No No

Accumulator No No No

Compressor Start Assist

Capacitor and Relay

Low Ambient Controller,

MotorMaster® Control,

Low-Ambient Pressure Switch

Liquid-Line Solenoid Valve

Ball Bearing Fan Motor Yes‡ No No

For tubing line sets between 50 and 175 ft, refer to the Residential Split-System Long-Line Application Guideline.
† Only when low-pressure switch is used.
‡ Required for Low-Ambient Controller (full modulation feature) and MotorMaster Control only.

or

Wind Baffle See Low-Ambient Instructions No No
Coastal Filter No No Yes
Support Feet Recommended No Recommended

or

Hard Shutoff TXV

APPLICATIONS

(Below 55°F)

Yes Yes No

Yes No No

No

REQUIRED FOR

LONG-LINE

APPLICATIONS

(Over 50 Ft)

See Long-Line

Application

Guideline

REQUIRED FOR

SEA COAST
APPLICATIONS
(Within 2 Miles)

No

ACCESSORY DESCRIPTION AND USAGE (Listed Alphabetically)

Ball Bearing Fan Motor

A fan motor with ball bearings which permits speed reduction while maintaining bearing lubrication.

SUGGESTED USE: Required on all units where Low-Ambient Controller (full modulation feature) or MotorMaster® Control has been added.

2.

Coastal Filter

A mesh screen inserted under the top cover and inside the base pan to protect the condenser coil from salt damage without restricting airflow.

SUGGESTED USE: In geographic areas where salt damage could occur.

3.

Compressor Start Assist — Capacitor/Relay Type

Start capacitor and start relay gives “hard” boost to compressor motor at each start-up.

SUGGESTED USE: Installations where interconnecting tube length exceeds 50 ft.

4.

Compressor Start Assist — PTC Type

Solid state electrical device which gives a “soft” boost to compressor motor at each start-up.

SUGGESTED USE: Installations with marginal power supply.

5.

Crankcase Heater

An electric resistance heater which mounts to the base of the compressor to keep the lubricant warm during off cycles. Improves compressor lubrication
on restart and minimizes chance of refrigerant slugging. May or may not include a thermostat control.

SUGGESTED USE: When interconnecting tube length exceeds 50 ft.

6.

Cycle Protector

Solid state timing device which prevents compressor rapid recycling. Control provides an approximate 5-minute delay after power to the compressor has
been interrupted for any reason, including normal room thermostat cycling.

SUGGESTED USE: Installations in areas where power interruptions are frequent.

7.

Evaporator Freeze Thermostat

An SPST temperature actuated switch which stops unit operation when evaporator reaches freeze-up conditions.

SUGGESTED USE: All units where Winter Start Control has been added.

8.

Filter Drier

A device for removing contaminants from refrigerant circulating in an air conditioner: 1-direction flow.

SUGGESTED USE: All split system air conditioners.

9.

High-Pressure Switch

Auto reset SPST switch activated by refrigerant pressure on high side of refrigerant circuit. Cycles compressor off if refrigerant pressure rises to 400 ± 10
psig and resets at 298 ± 20 psig. Provides protection against compressor damage due to loss of outdoor airflow. To prevent rapid compressor recycling,
Cycle Protector can be used with this switch.

SUGGESTED USE: Installations exposed to very ‘‘dirty’’ outdoor air.

10.

Liquid-Line Solenoid Valve (LSV)

An electrically operated shutoff valve to be installed at the outdoor or indoor unit (depending on tubing configuration) and which stops and starts refrigerant
liquid flow in response to compressor operation. Maintains a column of refrigerant liquid ready for action at next compressor operation cycle.

NOTE: Compressor Start Assist — Capacitor/Relay Type must also be used. Do not use with hard shutoff TXV.

SUGGESTED USE: For improved system performance in air conditioners for certain combinations of indoor and outdoor units. Refer to ARI Unitary Directory.

Installations where outdoor design temperature exceeds 105°F (40.6°C).
Replacement installations with hard shutoff expansion valve on indoor coil.
Installations where Liquid-Line Solenoid Valve has been added.

Replacement installations with rapid pressure balance (RPB) expansion valve on indoor coil.

When unit will be operated below 55°F (12.8°C) outdoor air temperature. Use with Low-Ambient Controller.
All commercial installations.

Where user is likely to “play” with the room thermostat.
All commercial installations.
Installations where interconnecting tube length exceeds 50 ft.
High-rise applications.

Installations where condenser inlet air temperature exceeds 125°F (51.7°C).

In certain long line-applications. Refer to Residential Split System Long-Line Application Guideline.

—6—

ACCESSORY DESCRIPTION AND USAGE (Listed Alphabetically) Continued

11. Low-Ambient Controller
Head pressure controller is a cycle control device activated by a temperature sensor mounted on a header tube of the outdoor coil. It is designed to cycle
the outdoor fan motor in order to maintain condensing temperature within normal operating limits (appro ximately 100°F high and 60°F lo w). The control will
maintain working head pressure at low-ambient temperatures down to 0°F when properly installed.

SUGGESTED USE: Cooling operation at outdoor temperatures below 55°F (12.8°C).

12.

Low-Ambient Pressure Switch

A long life pressure switch which is mounted to outdoor unit service valve. It is designed to cycle the outdoor fan motor in order to maintain head pressure
within normal operating limits (approximately 100 psig to 225 psig). The control maintains w orking head pressure at low-ambient temper atures down to 0°F
when properly installed.

SUGGESTED USE: Cooling operation at outdoor temperatures below 55°F (12.8°C).

13.

Low-Pressure Switch

Auto reset SPST switch activated by refrigerant pressure on liquid side of refrigerant circuit. Cycles compressor off if refrigerant charge is lost. To prevent
rapid compressor recycling, Cycle Protector can be used with this switch.

SUGGESTED USE: Where indoor coil is exposed to ‘‘dirty’’ air.

14.

MotorMaster® Control

A fan speed control device activated by a temperature sensor. Designed to control condenser fan motor speed in response to the saturated, condensing
temperature during operation in cooling mode only. For outdoor temperatures down to –20°F, it maintains condensing temperature at 100°F ± 10°F.

SUGGESTED USE: Cooling operation at outdoor temperatures below 55°F.

15.

Outdoor Air Temperature Sensor

A device that allows the temperature at a remote location (outdoors) to be displayed at the thermostat.

SUGGESTED USE: All corporate programmable thermostats.

16.

Support Feet

Four stick-on plastic feet which raise the unit 4 in. above the mounting pad. This allows sand, dirt, and other debris to be flushed from the unit base
minimizing corrosion.

SUGGESTED USE: Coastal installations.

17.

Thermostatic Expansion Valve (TXV)

A modulating flow-control valve which meters refrigerant liquid flow rate into the evaporator in response to the superheat of the refrigerant gas leaving the
evaporator. Kit includes valve, adapter tubes, and external equalizer tube. Both hard shutoff and RPB type valves are available. Do not use hard shutoff
TXV with Liquid-Line Solenoid Valve.

SUGGESTED USE: For improved system performance in cooling mode for certain combinations of indoor and outdoor units. Refer to ARI Unitary Directory.

18.

Time-Delay Relay

An SPST delay relay which briefly continued operation of the indoor blower motor to provide additional cooling after the compressor cycles off.

SUGGESTED USE: For improved efficiency ratings for certain combinations of indoor and outdoor units. Refer to ARI Unitary Directory.

19.

Winter Start Control

An SPST delay relay which bypasses the low-pressure switch for approximately 3 minutes to permit start-up for cooling operation under low-load
conditions.

SUGGESTED USE: All air conditioners where Low-Ambient Controller has been added.

All commercial installations.

All commercial installations.

Windy areas or where debris is normally circulating.
Rooftop installations.
For improved sound rating.

Required for use on all zoning systems.

Required for use on all zoning systems.

SOUND POWER (dBA)

UNIT
SIZE

018 68 50.0 56.5 61.0 63.5 59.0 54.5 45.5
024 70 55.0 61.5 62.5 64.5 61.0 55.0 49.0
030 72 55.0 58.0 61.5 63.5 62.5 56.5 51.5
036 74 56.5 63.5 68.0 70.0 63.0 57.5 52.0
042 74 56.5 60.5 64.5 67.5 61.5 58.0 53.0
048 74 56.0 61.0 67.0 67.5 66.0 63.0 56.5
060 76 63.5 66.0 69.0 69.0 66.5 64.0 56.5

SOUND

LEVEL

(dBA)

125 250 500 1000 2000 4000 8000

OCTAVE BAND CENTER FREQUENCY (Hz)

—7—

UNIT
SIZE-

SERIES

CC5A/CD5AA018 17,400 NONE — 12.00 12.00 12.00 11.05
CC5A/CD5AA024 17,800 NONE — 12.20 12.20 12.20 11.25
CC5A/CD5AW024 17,800 NONE — 12.20 12.20 12.20 11.25

CK5A/CK5BA024 17,800 NONE — 12.20 12.20 12.20 11.25

CK5A/CK5BW024 17,800 NONE — 12.20 12.20 12.20 11.25
F(A,B)4AN(F,C)018 17,000 TDR 12.00 — 12.00 — 10.95
F(A,B)4AN(F,C)024 17,600 TDR 12.50 — 12.50 — 11.45

FF1(B,C,D)NA018 17,000 TDR 12.20 — 12.20 — 11.30

FF1(B,C,D)NA024 17,600 TDR 12.20 — 12.20 — 11.30

018-F

CC5A/CD5AA018 17,000 TDR 13.50 — 13.50 — 12.30

CC5A/CD5AA024 17,600 TDR 14.00 — 14.00 — 12.65

CK5A/CK5BA018 17,000 TDR 13.50 — 13.50 — 12.30

CK5A/CK5BA024 17,600 TDR 14.00 — 14.00 — 12.65

CC5A/CD5AW024 17,600 TDR 13.50 — 13.50 — 12.45

CK5A/CK5BW024 17,600 TDR 13.50 — 13.50 — 12.45

CC5A/CD5AW024 17,600 TDR 13.50 — 13.50 — 12.55

CK5A/CK5BW024 17,600 TDR 13.50 — 13.50 — 12.55

CC5A/CD5AA024

CC5A/CD5AA030 23,200 NONE — 12.20 12.20 12.20 10.95

CC5A/CD5AW024 23,000 NONE — 12.00 12.00 12.00 10.85

CC5A/CD5AW030 23,200 NONE — 12.20 12.20 12.20 10.95

CK5A/CK5BA024 23,000 NONE — 12.00 12.00 12.00 10.85

CK5A/CK5BA030 23,200 NONE — 12.20 12.20 12.20 11.05

CK5A/CK5BW024 23,000 NONE — 12.00 12.00 12.00 10.85

CK5A/CK5BW030 23,200 NONE — 12.20 12.20 12.20 11.05

F(A,B)4ANF024 23,200 TDR 12.00 — 12.00 — 10.95
F(A,B)4ANF030 23,600 TDR 12.20 — 12.20 — 11.25

FF1(B,C,D)NA024 23,000 TDR 12.00 — 12.00 — 10.85

FF1(B,C,D)NA030 23,600 TDR 12.20 — 12.20 — 11.10

024-F

CC5A/CD5AA030 23,600 TDR 13.50 — 13.50 — 12.25

CK5A/CK5BA024 23,000 TDR 13.00 — 13.00 — 11.90

CK5A/CK5BA030 23,200 TDR 13.50 — 13.50 — 12.15

CK5A/CK5BW030 23,200 TDR 13.50 — 13.50 — 12.15

CC5A/CD5AA024 23,200 TDR 13.00 — 13.00 — 11.90

CC5A/CD5AA030 23,600 TDR 13.50 — 13.50 — 12.20

CK5A/CK5BW030 23,200 TDR 13.00 — 13.00 — 12.05

CC5A/CD5AA024 23,200 TDR 13.00 — 13.00 — 11.90

CC5A/CD5AA030 23,600 TDR 13.50 — 13.50 — 12.20

CK5A/CK5BW024 23,000 TDR 13.00 — 13.00 — 11.75

CK5A/CK5BW030 23,200 TDR 13.00 — 13.00 — 12.00

CC5A/CD5AA024 23,200 TDR 13.00 — 13.00 — 11.90

CC5A/CD5AA030 23,600 TDR 13.50 — 13.50 — 12.20

See notes on page 13.

*

*

COMBINATION RATINGS

SEER

FACTORY­SUPPLIED

INDOOR

SECTION

CK5BA018

CE3AA024 17,600 NONE — 12.20 12.20 12.20 11.25
CK3BA024 17,800 NONE — 12.20 12.20 12.20 11.25

FC4BNF024 17,600 TDR & TXV 12.50 — — — 11.45

FG3AAA024 17,400 NONE — 12.00 12.00 12.00 11.05
FK4CNF001 18,000 TDR & TXV 14.00 — — — 12.85
FK4CNF002 18,000 TDR & TXV 14.00 — — — 12.95

CK3BA024 17,600 TDR 14.00 — 14.00 — 12.65

CE3AA024 23,000 NONE — 12.00 12.00 12.00 10.95
CE3AA030 23,200 NONE — 12.20 12.20 12.20 11.10
CF5AA024 23,000 NONE — 12.00 12.00 12.00 10.95
CK3BA024 23,000 NONE — 12.00 12.00 12.00 10.85
CK3BA030 23,200 NONE — 12.20 12.20 12.20 11.05

FC4BNF024 23,200 TDR & TXV 12.00 — — — 10.95
FC4BNF030 23,600 TDR & TXV 12.20 — — — 11.25

FG3AAA024 22,800 NONE — 11.80 11.80 11.80 10.70
FK4BNF001 23,400 TDR & TXV 13.50 — — — 12.35
FK4BNF002 23,600 TDR & TXV 13.50 — — — 12.50
FK4BNF003 23,600 TDR & TXV 14.00 — — — 12.80
FK4BNF004 24,000 TDR & TXV 14.00 — — — 12.80
FK4CNF001 23,400 TDR & TXV 13.50 — — — 12.35
FK4CNF002 23,600 TDR & TXV 13.50 — — — 12.50
FK4CNF003 23,600 TDR & TXV 14.00 — — — 12.80

CE3AA030 23,600 TDR 13.50 — 13.50 — 12.35
CK3BA024 23,000 TDR 13.00 — 13.00 — 11.90
CK3BA030 23,200 TDR 13.50 — 13.50 — 12.15

CK3BA024 23,000 TDR 13.00 — 13.00 — 11.75
CK3BA030 23,200 TDR 13.00 — 13.00 — 12.05

CK3BA024 23,000 TDR 13.00 — 13.00 — 11.75
CK3BA030 23,200 TDR 13.00 — 13.00 — 12.00

TOTAL CAP.

BTUH

17,400 NONE — 12.00 12.00 12.00 11.05

23,000 NONE — 12.00 12.00 12.00 10.85

ENHANCE-

MENT

COILS + 333(B,J)AV036060 VARIABLE SPEED FURNACE

COILS + 355MAV042060 VARIABLE SPEED FURNACE

COILS + 355MAV042080 VARIABLE SPEED FURNACE

COILS + 333(B,J)AV036060 VARIABLE SPEED FURNACE

COILS + 355MAV042040 VARIABLE SPEED FURNACE

COILS + 355MAV042060 VARIABLE SPEED FURNACE

COILS + 355MAV042080 VARIABLE SPEED FURNACE

ST ANDARD

RA TING

BRYANT GAS

FURNACE OR

ACCESSORY

TDR†

ACCESSOR Y

TXV‡ LLS

EER

—8—

UNIT

SIZE-

SERIES

024-F

030-F

See notes on page 13.

CK5A/CK5BW024 23,000 TDR 13.00 — 13.00 — 12.00
CK5A/CK5BW030 23,200 TDR 13.50 — 13.50 — 12.25

CC5A/CD5AA030

CC5A/CD5AA036 29,600 NONE — 12.50 12.50 12.50 10.90
CC5A/CD5AW030 29,000 NONE — 12.00 12.00 12.00 10.55

CK5A/CK5BA030 29,000 NONE — 12.00 12.00 12.00 10.60
CK5A/CK5BA036 29,600 NONE — 12.50 12.50 12.50 10.95

CK5A/CK5BN036 27,600 NONE — 12.50 12.50 12.50 10.95
CK5A/CK5BW030 29,000 NONE — 12.00 12.00 12.00 10.60
CK5A/CK5BW036 29,600 NONE — 12.50 12.50 12.50 10.95

F(A,B)4ANF030 29,200 TDR 12.00 — 12.00 — 10.70
F(A,B)4ANF036 29,600 TDR 12.00 — 12.00 — 10.65

FF1(B,C,D)NA030 29,600 TDR 12.00 — 12.00 — 10.70

CC5A/CD5A036 30,000 TDR 13.50 — 13.50 — 12.05

CK5A/CK5BA030 29,000 TDR 13.00 — 13.00 — 11.30

CK5A/CK5BA036 29,600 TDR 13.50 — 13.50 — 11.85

CK5A/CK5BN036 27,600 TDR 13.00 — 13.00 — 11.70
CK5A/CK5BW030 29,000 TDR 13.00 — 13.00 — 11.30

CC5A/CD5AA036 30,000 TDR 13.50 — 13.50 — 12.05

CK5A/CK5BW030 29,000 TDR 13.00 — 13.00 — 11.50
CK5A/CK5BW036 29,600 TDR 13.50 — 13.50 — 12.00

CC5A/CD5AA030 29,600 TDR 13.00 — 13.00 — 11.45
CC5A/CD5AA036 30,000 TDR 13.50 — 13.50 — 11.95

CK5A/CK5BW030 29,000 TDR 12.50 — 12.50 — 11.10
CK5A/CK5BW036 29,600 TDR 13.00 — 13.00 — 11.65

CC5A/CD5AA030 29,600 TDR 13.00 — 13.00 — 11.45
CC5A/CD5AA036 30,000 TDR 13.50 — 13.50 — 11.95

CK5A/CK5BA036 29,600 TDR 13.00 — 13.00 — 11.65
CK5A/CK5BW030 29,000 TDR 12.50 — 12.50 — 11.10

CC5A/CD5AA030 29,600 TDR 13.00 — 13.00 — 11.45
CC5A/CD5AA036 30,000 TDR 13.50 — 13.50 — 11.95

CK5A/CK5BW030 29,000 TDR 12.50 — 12.50 — 11.20
CK5A/CK5BW036 29,600 TDR 13.00 — 13.00 — 11.75

CK5A/CK5BW030 29,000 TDR 12.50 — 12.50 — 11.05
CK5A/CK5BW036 29,600 TDR 13.00 — 13.00 — 11.60

CK5A/CK5BW030 29,000 TDR 13.00 — 13.00 — 11.45
CK5A/CK5BW036 29,600 TDR 13.50 — 13.50 — 12.00

*

COMBINATION RATINGS Continued

SEER

FACTORY-

SUPPLIED

INDOOR

SECTION

CK3BA024 23,000 TDR 13.00 — 13.00 — 12.00
CK3BA030 23,200 TDR 13.50 — 13.50 — 12.25

CD5AW036 29,600 NONE — 12.50 12.50 12.50 10.90

CE3AA030 29,000 NONE — 12.00 12.00 12.00 10.65
CE3AA036 29,600 NONE — 12.20 12.20 12.20 10.80
CF5AA036 29,600 NONE — 12.50 12.50 12.50 10.90
CK3BA030 29,000 NONE — 12.00 12.00 12.00 10.60
CK3BA036 29,600 NONE — 12.50 12.50 12.50 10.95

FC4BNF030 29,200 TDR & TXV 12.00 — — — 10.70
FC4BNF036 29,600 TDR & TXV 12.00 — — — 10.65

FG3AAA036 29,400 NONE — 12.00 12.00 12.00 10.70
FK4BNF001 29,600 TDR & TXV 13.00 — — — 11.45
FK4BNF002 29,600 TDR & TXV 13.40 — — — 11.55
FK4BNF003 30,000 TDR & TXV 13.80 — — — 12.10
FK4BNF004 30,200 TDR & TXV 14.00 — — — 12.00
FK4CNF001 29,600 TDR & TXV 13.00 — — — 11.45
FK4CNF002 29,600 TDR & TXV 13.40 — — — 11.55
FK4CNF003 30,000 TDR & TXV 13.80 — — — 12.10

CE3AA036 29,800 TDR 13.50 — 13.50 — 11.80
CK3BA030 29,000 TDR 13.00 — 13.00 — 11.30
CK3BA036 29,600 TDR 13.50 — 13.50 — 11.85

CE3AA036 29,800 TDR 13.50 — 13.50 — 11.80
CK3BA030 29,000 TDR 13.00 — 13.00 — 11.50
CK3BA036 29,600 TDR 13.50 — 13.50 — 12.00

CK3BA030 29,000 TDR 12.50 — 12.50 — 11.10
CK3BA036 29,600 TDR 13.00 — 13.00 — 11.65

CK3BA030 29,000 TDR 12.50 — 12.50 — 11.10
CK3BA036 29,600 TDR 13.00 — 13.00 — 11.65

CK3BA030 29,000 TDR 12.50 — 12.50 — 11.20
CK3BA036 29,600 TDR 13.00 — 13.00 — 11.75

CK3BA030 29,000 TDR 12.50 — 12.50 — 11.05
CK3BA036 29,600 TDR 13.00 — 13.00 — 11.60

CK3BA030 29,000 TDR 13.00 — 13.00 — 11.45
CK3BA036 29,600 TDR 13.50 — 13.50 — 12.00

TOTAL CAP.

BTUH

29,000 NONE — 12.00 12.00 12.00 10.55

ENHANCE-

MENT

COILS + 333(B,J)AV036060 VARIABLE SPEED FURNACE

COILS + 333(B,J)AV048080 VARIABLE SPEED FURNACE

COILS + 355MAV042040 VARIABLE SPEED FURNACE

COILS + 355MAV042060 VARIABLE SPEED FURNACE

COILS + 355MAV042080 VARIABLE SPEED FURNACE

COILS + 355MAV060080 VARIABLE SPEED FURNACE

COILS + 355MAV060100 VARIABLE SPEED FURNACE

ST ANDARD

RA TING

BRYANT GAS
FURNACE OR

ACCESSORY

TDR†

ACCESSOR Y

TXV‡ LLS

EER

—9—