Brother 5V6201 User Manual
User’s Guide
General Description
Operating Procedures
Appendix, etc.
z
Before using this printer, be sure to read this User’s Guide.
z
We suggest that you keep this manual in a handy place for future
reference.
MW-260
Mobile Printer
Introduction
Introduction
Thank you for purchasing the MPrint MW-260 (hereafter referred
to as “the printer”).
This monochrome thermal mobile printer is ultra-portable and
can be connected to a Pocket PC (PDA running Pocket PC) or a
computer to make quick printouts.
This User’s Guide contains operating precautions and instructions. Before using this printer, be sure to read this manual for
information on its correct operation.
In addition, we suggest that you keep this manual in a handy
place for future reference.
i
Federal Communications Commission (FCC) Declaration of Conformity (For USA Only)
Responsible Party:Brother International Corporation
declares that the product
Product Name : Brother MPrint MW-260
Model Number : MW-260
complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one
or more of the following measures:
-Reorient or relocate the receiving antenna
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
-Consult the dealer or an experienced radio / TV technician for
help.
-This device complies with FCC RF radiation exposure limits
set forth for an uncontrolled environment. The antenna used
for this transmitter must be installed to provide a separation
distance of at least 20 cm from all persons and must not be
co-located or operating in conjunction with any other antenna
or transmitter.
FCC WARNING
-Changes or modifications not expressly approved by Brother
Industries, Ltd. could void the user's authority to operate the
equipment.
100 Somerset Corporate Boulevard Bridgewater, NJ 08807-0911 USA
TEL : (908) 704-1700
MW-260 Quick Guide (English)
1
CAUTION
RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN
DISPOSE OF USED BATTERIES ACCORDING TO THE
The contents of this manual are subject to change without notice.
The contents of this manual may not be duplicated or reproduced,
partially or in full, without permission.
Please note that we assume no responsibility for damages
arising from earthquakes, fire, other disasters, actions of third
parties, the user's intentional or negligent operation, misuse or
operation under other special conditions.
Please note that we assume no responsibility for damage (such
as losses, loss of business profits, lost profits, business
disruptions or a lost means of communication) that may result
from the use or inability to use this printer.
If this printer should be defective due to faulty manufacturing, we
shall replace it during the warranty period.
We assume no responsibility for damages that may result from
incorrect operation of this printer by connecting incompatible
equipment or using incompatible software.
Microsoft® and Windows® are registered trademarks of
Microsoft Corporation in the United States and other countries.
The Bluetooth® word mark and logos are owned by the Bluetooth
Inc. and any use of such marks by Brother Industries, Ltd. under license.
This product contains IrFront of ACCESS CO., LTD.
Copyright (C) 1996-2006 ACCESS CO., LTD.
ACCESS and IrFront are trademarks or registered trademarks
of ACCESS CO., LTD. in Japan and other countries.
INCORRECT TYPE.
INSTRUCTIONS
.
®
SIG,
All other software and product names mentioned are trademarks or registered trademarks of their respective companies.
2
MW-260 Quick Guide (English)
1) What is Bluetooth?
Bluetooth is a type of short-range wireless technology that provides wireless
connectivity to users of computers and PDAs equipped with Bluetooth.
2) Precautions for using Bluetooth
Wireless connections are used in a wide range of fields. Therefore, in order to
prevent malfunctions with the following, Bluetooth should be turned off.
• Hospitals
• Aircraft
• Gasoline/Petrol stations
• Fire alarms
3) For better transmission
Bluetooth connectivity varies greatly according to its operating environment.
If a good connection cannot be achieved, try connecting again.
Connections are difficult to achieve in the following locations.
• Near electronic equipment
• Near broadcasting stations or wireless base stations
• Near wireless LAN (IEEE802.11)
4) Other features of Bluetooth technology
• Equipment using Bluetooth technology may require a few seconds until the
Bluetooth function can be used after it is turned on. This length of time differs
depending on the equipment. (This unit requires a maximum of 8 seconds.)
MW-260 Quick Guide (English)
3
Precautions
Precautions
Precautions indicated as shown below contain important safety
information and should be strictly observed.
If the printer malfunctions, immediately stop using it, and then
contact the sales representative where it was purchased.
The meanings for marks used in this manual are described below
Failur e to accurately obser ve instructions marked with
Danger
Warning
Caution
this symbol lead to an extremely high risk of death or
serious injuries.
Failur e to obser ve instructions marked with t his symbol
may result in death or serious injuries.
Failur e to obser ve instructions marked with t his symbol
may result in injuries or property damage.
.
v
Meanings for symbols used in this manual
Indicates danger
Indicates danger of fire under certain circumstances
Indicates danger of electric shock under certain circumstances
Indicates danger of burns under certain circumstances
Indicates an action that must not be performed
Indicates danger of combustion if fire is nearby
Indicates danger of sustaining injuries if the indicated part of the
printer is touched
Indicates danger of injuries, such as electric shock, if the indicated part if the printer is disassembled
Indicates danger of electric shock if the operation is performed
with wet hands
Indicates danger of electric shock if the printer is exposed to
wate r
Indicates an action that must be performed
Indicates that the power supply cord must be unplugged fr om the
electrical outlet
vi
Precautions
Concerning this printer (Recharge Lithium-ion Battery
Danger
Do not use thi s printer with any rechargeable batt ery other than
y
that specified, otherwise a f ire or an electric shock may result.
Carefully observe the following precautions for the
y
rechargeable lit hium-ion batter y (BT-200; hereaf ter, referred to
as “rechargeable battery”) i ncluded wit h the printer, ot herwise
heat or cracks may be produced, or a fire, an electric shock or
damage may result.
{
To recharge the battery, insert the rechargeable battery
into the MW-260, and then use the AC adapter designed
specifically for this printer.
{
Do not insert or use the rechargeable battery in any equip-
ment other than the MW-260. Do not directly connect it to
a power supply, car cigarette lighter or electrical outlet.
{
Do not expose the rechargeable battery or the printer with the
rechargeable battery installed to pressure, heat or an electric
charge (for example, an oven or microwave oven, clothes
dryer, high-voltage equipment or electromagnetic cooker).
{
Do not place the rechargeable battery or the printer with
the rechargeable battery installed near a fire or in a location exposed to heat or high temperatures (for example,
near a flame or stove, in the sun, or in a location where
the temperature is 60 °C or more, such as in a hot car).
{
Do not place the rechargeable battery or the printer with the
rechargeable battery installed near water or seawater. In
addition, do not drop them in water or allow them to get wet.
{
Do not short-circuit the terminals of the rechargeable bat-
tery or the printer with the rechargeable battery installed,
such as with a metal object.
{
Do not pierce or poke a hole in the rechargeable battery
or the printer with the rechargeable battery installed with
a sharp object, such as a nail.
{
Do not hit with a hammer, step on, throw, drop or apply a
strong shock to the rechargeable battery or the printer
with the rechargeable battery installed.
{
Do not disassemble or alter the rechargeable battery or
the printer with the rechargeable battery installed.
{
Do not use a damaged or deformed rechargeable battery.
{
Do not use in a corrosive environment (for example, exposed
to salty air or salt water, or acidic, alkaline or corrosive gas).
)
vii
Warning
Do not use this printer wherever it is prohibited, for exam-
y
ple, on an airplane, otherwise it may affect equipment,
resulting in an accident.
If this print er is to be used in special environments, for
y
example, near medical equipment, make sure in advance
that there would be no harmful effects from electromagnetic waves. Please note that we assume no responsibility
for injuries resulting from interference from electromagnetic
waves.
Do not insert foreign objects into the printer or its connec-
y
tors and ports, otherwise a fire, an electric shock or damage may result.
If foreign objects are dropped into the printer, immediately
y
turn it off, unplug the AC adapter from the electrical outlet,
and then contact the sales representative where it was purchased. If you continue to operate the printer, a fire, an
electric shock or damage may result.
Do not operate, recharge or store the printer in the follow-
y
ing locations, otherwise it may leak or fire, electric shock or
damage may result.
{
Near water, such as in a bathroom or near a water
heater, or in an extremely humid location
{
In a location where it is exposed to rain or moisture
{
In an extremely dusty location
{
In an extremely hot location, such as naked flames, or
heaters or direct sunlight
{
In a closed car under a hot sun
{
In a location where condensation may form
When lightening is seen, unplug the AC adapter from the
y
electrical outlet. If lightening hits nearby, do not touch the
printer, since there is a chance of electric shock.
viii
Precautions
Warning
Liquid leaking from the printer or rechargeable lithium-ion
y
battery may indicate that the rechargeable bat tery is damaged. Immediately move the printer or rechargeable battery away from flames to avoid the risk of a fire.
In addition, do not touch the leaking liquid. This liquid may
damage your eyes or skin if brought in contact with them. If
the liquid contacts your eyes, immediately ri nse them with
water and consult a medical professional. If the liquid contacts your skin or clothing, immediately r inse them with
water. Place the printer in a bag to isolate it.
Do not try to disassemble or alter this printer, otherwise
y
fire, electric shock or damage may result. For servicing,
adjustments or repairs, contact the sales representative
where it was purchased. (The warrant y does not cover
repairs for damage resulting from disassembly or alterations performed by the user.)
The printer may be damaged if it is dropped or subjected to
y
strong shocks, for example, from being stepped on. If you
continue to operate a damaged printer, a fire or an electric
shock may result. If the printer is damaged, immediately
turn it off, unplug the AC adapter from the electrical outlet,
and then contact the sales representative where it was purchased.
If the printer operates abnormally, for example, if it pro-
y
duces smoke, an unusual odor or an unusual noise, stop
using it, otherwise fir e, electric shock or damage may
result. Immediately turn off the printer, unplug the AC
adapter from the electrical outlet, and then contact the
sales representative where it was purchased for repairs.
Do not charge the printer with a charger other than that
y
specified.
ix
Warning
If the printer is not fully charged after the specified amount
y
of time has passed, stop charging it, otherwise fire, electric
shock or damage may result.
Caution
Keep the printer and its accessories (rechargeable battery,
y
consumables, plastic bags, labels, etc.) out of the reach of
children, particularly infants, otherwise injuries or accidents
(such as ingestion) may result.
Stop operating the printer if it leaks or becomes discolored,
y
deformed or otherwise defective.
Do not operate the printer while holding only the paper cas-
y
sette cover. If the cover comes off and the printer falls, injuries may result.
Others
The Recharge Lithium-ion Battery is slightly charged so
y
that t he operation of the printer can be veri fied; however,
the battery should be fully charged with the AC adapter
before the print er is used.
If the printer will not be used for a long period of time,
y
remove the rechargeable lithium-ion battery from the
printer, and then store it in a location where it is not
exposed t o high humidity, high temperatur es (15 °C or less
is recommended) or static electricity. In order to maintain
the efficiency and life of the rechargeable lithium-ion battery, recharge it at least every six months.
x
Others
This printer is powered with a Recharge Lith-
y
ium-ion Battery. If this printer can only be
used for a short period of time, even though it
is fully charged, the battery may have reached
the end of its service life. Replace the
Recharge Lithium-ion Battery with a new one.
When replacing the battery, disconnect it by
affixing tape to the terminals that contact the
printer.
Concerning the AC adapter
Warning
Only use the AC adapter designed specifically for this
y
printer, otherwise fire, electric shock or damage may result.
Do not plug the printer into an electrical outlet other than a
y
household outlet (AC 220 V
tric shock or damage may result.
Do not touch the AC adapter or the power supply plug with
y
wet hands, otherwise electric shock may occur.
Precautions
Li-ion
–
240 V), otherwise fire, elec-
Do not try to disassemble, alter or repair the AC adapter,
y
otherwise fire, electric shock or injuries may result.
For servicing, adjustments or repairs, contact the sales
representative where the printer was purchased.
xi
Warning
Do not spill water or drinks, such as coffee or juice, on the
y
AC adapter. In addition, do not use the adapter in a location where it may get wet, otherwise combustion or electric
shock may result.
If the power supply pl ug becomes dir ty, for example, with
y
dust, unplug it from the electrical outlet, and then wipe it
with a dry cloth. If you continue to use a dirty power supply
plug, a fire may result.
Caution
When unplugging the power supply cord, do not pull on the
y
cord, otherwise fire or electric shock may result.
Do not insert foreign objects into the terminals of the AC
y
adapter, otherwise burns or electric shock may result.
Incorrectly using the AC adapter may result in fire or
y
electric shock. Therefore, observe the following precautions.
{
Do not damage it.
{
Do not modify it.
{
Do not twist it.
{
Do not severely bend it.{Do not allow it to be
{
Do not pull on it. pinched.
If the AC adapter is damaged, request a new one from the
y
sales representative where the printer was purchased.
Keep the AC adapter out of the reach of children, particu-
y
larly infants, otherwise injuries may result.
{
Do not place objects on it.
{
Do not subject it to heat.
{
Do not bind it.
xii
Precautions
Caution
Do not use the AC adapter near microwave ovens, other-
y
wise damage may r esult.
Do not use the AC adapter near flames or heaters. If the
y
covering of the AC adapter cord melts, fire or electric shock
may result.
Before maintaining the printer, for example, when cleaning
y
it, unplug the AC adapter from the electrical outlet, otherwise electric shock may result.
If the printer is not to be used for a long period of time, be
y
sure to unplug the AC adapter from the unit and the electrical outlet for safety reasons.
Do not wind the AC adapter cable around the adapter or
y
bend the cable, otherwise the cable may be damaged.
xiii
Loading...