• Increase the distance between the
equipment and receiver.
• Connect the equipment to an outlet
on a circuit different from that to
which the receiver is connected.
• Consult the dealer or an
experienced radio/TV technician
for help.
1. Micro USB Charging Port
2. Dust Cover
3. Aux-In Port
4. Power/Pairing Button
5. Volume Down Button
6. Play/Pause/Call Button
7. Volume Up Button
8. Micro USB Charging Cable
(not shown)
4 5 6 7
1 32
Fold Fold Fold Fold Fold
CHARGING THE PACK
SPEAKER
1. Turn off Pack Speaker before
charging.
2. Connect the speaker to a PC/
Laptop or a 5V USB adapter (not
included) with the included USB
charging cable.
3. The Battery Indicator will turn on
red during charging and will turn
off when fully charged. It takes
about 2 hours to fully charge.
NOTE: The red LED will keep flashing
fast and the indication tone will repeat
every 30 seconds when battery is low.
TURNING ON/OFF THE
SPEAKER
1. Press and hold the Power Button
for 3 seconds to turn on the
speaker. The Battery and
Bluetooth
®
indicators turn on at the
same time.
2. Press and hold the Power Button
for 3 seconds to turn the speaker
off.
PAIRING YOUR DEVICE
1. Please keep the Pack Speaker and
the mobile device within 1 meter
of each other.
2. Turn on the Speaker. When the red
LED blinks quickly, the speaker is in
standby for pairing.
LOCATION OF PARTS AND
CONTROLS
This equipment complies with Part 15
ot the FCC Rules. Operation is subject
to the following two conditions:
1. This equipment may not cause
harmful interference.
2. This equipment must accept any
interference received, including
interference that may cause
undesired operation.
Modifications not authorized by the
manufacturer may void the user’s
authority to operate this device.
FCC ID: 2ABPRV9
Merrimack, New Hampshire, USA 03054
800-846-3000 • Brookstone.com
310850/310851/310848/310849
SPECIFICATIONS
Power Output: 3W
DC Input: 5V 500mA
Range: Class 2, up to 33 ft (10m)
Battery Capacity: 3.7V 800mAh
Charging Time: Approx. 2 hours
Battery Life: Approx. 5 hours
Compatibility: Bluetooth 2.0 or above
device with A2DP/AVRCP/HFP/HSP
Fold Fold Fold Fold Fold
The Bluetooth® word mark and logos
are registered trademarks owned of
Bluetooth SIG, Inc. and any use
of such marks by Brookstone is under
license.
Store the speaker in a cool, dry place.
1. When you have an incoming call,
the speaker sounds an incoming
call tone. Both the speaker and your
cellphone may ring, depending on
your cellphone settings.
2. To answer an incoming call, short
press Play/Pause Button to answer
the call.
3. To reject an incoming call, long
press Play/Pause Button to reject
the call.
4. To end a call, short press
Play/Pause Button once.
5. If, while you are listening to music,
your phone rings and you answer
the call, the music selection will
then continue from where it had
stopped after you end the call.
NOTES:
LISTENING TO YOUR AUDIO
DEVICE
1. Play your audio device as you
normally would.
2. Volume may be adjusted on your
audio device or by pressing and
holding the Volume Up or Down
buttons on the speaker.
3. A single press of the Volume Up
or Down buttons will advance to
the next track or go back to the
previous track.
4. To pause audio, press the Play/Pause
Button on the Speaker. To resume
audio playback, press the Play/Pause
Button again.
PLAYING MUSIC THROUGH A
WIRED CONNECTION
You can connect your audio device to
the speaker with a 3.5mm audio cable
(not included).
1. Plug one end of the cable into your
audio device, just like you would a
pair of headphones.
2. Plug the other end of the cable into
the speaker's AUX-IN port.
3. Use your audio device to control
music playback and volume
through speaker.
WATER-RESISTANT
1. Pack Speaker is compliant with
IPX4 waterproof standard “splash
proof in all directions.”
2. Never place the speaker under
running water or submerge
the speaker in water.
3. Once the speaker is in pairing mode
and your device is ready to pair,
select ‘Pack Speaker.’ If prompted,
use 0000 as a PIN for the pairing
code. Once the speaker is selected,
LED indicator will change to solid
blue to complete pairing.
.
1. If pairing is not successful, turn
the speaker off and on again.
2. After successful pairing, paired
devices will remember each other.
3. The AUX-IN will take priority over
Bluetooth
®
. Bluetooth® connection
is disconnected when AUX-IN is
plugged in. Bluetooth
®
will be
reconnected when AUX-IN is
unplugged.
CARE AND STORAGE
MOBILE PHONE OPERATION
Loading...