Briteq COB PAR56-100WW Service Manual

ENGLISH USER MANUAL
Thank you for buying this BRITEQ® product. To take full advantage of all possibilities and for your own safety, please read these operating instructions very carefully before you start using this unit.
FEATURES
This unit is radio-interference suppressed. This product meets the requirements of the current European and national guidelines. Conformity has been established and the relevant statements and documents have been deposited by the manufacturer. This device was designed to produce decorative effect lighting and is used in light show systems.
High Power LED PARCAN, perfect for showrooms, shops, exhibition booths, rental, … Uses a powerful 100W white COB LED in a classic PAR armature Available in 2 color temperatures:
WW (warm white): 3200K for a warm and cozy atmosphere CW (cold white): 5600K daylight, perfect for showrooms, shops and TV/video
LCD-display to select different working modes:
Standalone (master): set dimmer + strobe (if needed) Master/slave mode: connect several projectors together, the first projector controls the others. DMX-controlled, 1CH: dimmer
DMX-controlled, 2CH: dimmer, strobe Selectable lamp behavior: halogen lamp (slow) or led (fast) Four dimmer curves: linear, square, inverse square, S-curve In case of DMX failure you can choose between blackout and freeze mode. Wide 60° beam angle for uniform output. Very low noise fan cooling. The filter frame can be used to add optional color filters. Available in Black and Silver polished
BEFORE USE
Before you start using this unit, please check if there’s no transportation damage. Should there be any, do
not use the device and consult your dealer first.
Important: This device left our factory in perfect condition and well packaged. It is absolutely necessary
for the user to strictly follow the safety instructions and warnings in this user manual. Any damage caused by mishandling is not subject to warranty. The dealer will not accept responsibility for any resulting defects or problems caused by disregarding this user manual.
Keep this booklet in a safe place for future consultation. If you sell the fixture, be sure to add this user
manual.
Check the contents:
Check that the packing contains the following items:
Operating instructions COB PAR56-100CW (5600K) or COB PAR56-100WW (3200K) Filter frame
BRITEQ® 1/39 COB PAR56-100
ENGLISH USER MANUAL
CAUTION: To reduce the risk of electric shock, do not remove the top cover. No user-serviceable parts inside. Refer servicing to qualified service personnel only.
The lightning flash with arrowhead symbol within the equilateral triangle is intended to alert the use or the presence of un-insulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock.
The exclamation point within the equilateral triangle is intended to alert the user to the presence of important operation and maintenance (servicing) instructions in the literature accompanying this appliance.
This symbol means: indoor use only
This symbol means: Read instructions
This symbol means: Safety Class I appliance
This symbol determines: the minimum distance from lighted objects. The minimum distance between light-output and the illuminated surface must be more than x meters
The device is not suitable for direct mounting on normally flammable surfaces. (suitable only for mounting on non-combustible surfaces)
CAUTION: Do not stare at operating lamp. May be harmful to the eyes.
SAFETY INSTRUCTIONS:
To protect the environment, please try to recycle the packing material as much as possible. To prevent fire or shock hazard, do not expose this appliance to rain or moisture. To avoid condensation to be formed inside, allow the unit to adapt to the surrounding temperatures when
bringing it into a warm room after transport. Condense sometimes prevents the unit from working at full performance or may even cause damages.
This unit is for indoor use only. Don’t place metal objects or spill liquid inside the unit. Electric shock or malfunction may result. If a foreign
object enters the unit, immediately disconnect the mains power.
Locate the fixture in a well ventilated spot, away from any flammable materials and/or liquids. The fixture
must be fixed at least 50cm from surrounding walls.
Don’t cover any ventilation openings as this may result in overheating.  Prevent use in dusty environments and clean the unit regularly. Keep the unit away from children. Inexperienced persons should not operate this device. Maximum safe ambient temperature is 40°C. Don’t use this unit at higher ambient temperatures. Make sure the area below the installation place is free from unwanted persons during rigging, de-rigging
and servicing.
Allow the device about 10 minutes to cool down before to start servicing. Always unplug the unit when it is not used for a longer time or before to start servicing. The electrical installation should be carried out by qualified personal only, according to the regulations for
electrical and mechanical safety in your country.
Check that the available voltage is not higher than the one stated on the unit. The power cord should always be in perfect condition. Switch the unit immediately off when the power cord
is squashed or damaged. It must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.
 Never let the power-cord come into contact with other cables!  This fixture must be earthed in order to comply with safety regulations.  Don’t connect the unit to any dimmer pack.  Always use an appropriate and certified safety cable when installing the unit.  In order to prevent electric shock, do not open the cover. There are no user serviceable parts inside.  Never repair a fuse or bypass the fuse holder. Always replace a damaged fuse with a fuse of the same
type and electrical specifications!
In the event of serious operating problems, stop using the fixture and contact your dealer immediately.
BRITEQ® 2/39 COB PAR56-100
ENGLISH USER MANUAL
The housing and the lenses must be replaced if they are visibly damaged. Please use the original packing when the device is to be transported. Due to safety reasons it is prohibited to make unauthorized modifications to the unit.
Important: Never look directly into the light source! Don’t use the effect in the presence of persons suffering
from epilepsy.
DESCRIPTION:
1. FILTER FRAME CLIPS: can be used to install color filters etc.
2. BRACKET: with knob to fasten the unit and a mounting hole to fix a mounting hook.
3. DMX INPUT: 3pin male XLR-connector used to connect the projector with the DMX controller or with the
previous unit in the DMX chain.
4. DMX OUTPUT: 3pin female XLR-connector used to connect the projector with the next unit in the DMX
chain.
5. DISPLAY shows the various menus and the selected functions.
6. DOWN button: to lower the values shown on the display.
7. UP button: to increase the values shown on the display.
8. ENTER button: used to confirm your choice or to enter the setup mode of a function.
9. MODE button: used to browse the different functions in the menu
10. Mains input: equipped with a 1.3m mains cable.
11. Fuse holder: always replace a damaged fuse with a fuse of the same type and electrical specifications!
OVERHEAD RIGGING
Important: The installation must be carried out by qualified service personal only. Improper
installation can result in serious injuries and/or damage to property. Overhead rigging requires extensive experience! Working load limits should be respected, certified installation materials should be used, the installed device should be inspected regularly for safety.
Make sure the area below the installation place is free from unwanted persons during rigging, de-rigging
and servicing.
The device should be installed out of reach of people and outside areas where persons may walk by or be
seated.
Before rigging make sure that the installation area can hold a minimum point load of 10times the device’s
weight.
Always use a certified safety cable that can hold 12times the weight of the device when installing the unit.
This secondary safety attachment should be installed in a way that no part of the installation can drop more than 20cm if the main attachment fails.
 The device should be well fixed; a free-swinging mounting is dangerous and may not be considered!  Don’t cover any ventilation openings as this may result in overheating.  The operator has to make sure that the safety-relating and machine-technical installations are approved by
BRITEQ® 3/39 COB PAR56-100
ENGLISH USER MANUAL
an expert before using them for the first time. The installations should be inspected every year by a skilled person to be sure that safety is still optimal.
ELECTRICAL INSTALLATION
Important: The electrical installation should be carried out by qualified personal only, according to the regulations for electrical and mechanical safety in your country.
Electrical installation for 1 standalone unit:
Insert the mains cable. The unit starts working immediately in the last selected mode. Refer to chapter HOW TO SETUP to learn how to switch between the different working modes.
Electrical installation for two or more units in master/slave:
Connect several units together using good quality balanced microphone cables. The unit that has no
cable connected to its DMX-input is the “master”, the others are the slave units.
Make sure that all units are connected to the mains. Refer to chapter HOW TO SETUP for more information. Done!
Electrical installation for two or more units in DMX-mode:
The DMX-protocol is a widely used high speed signal to control intelligent light equipment. You need to
“daisy chain” your DMX controller and all the connected units with a good quality
balanced cable.
To prevent strange behavior of the light effects, due to interferences, you must use
a 90Ω to 120Ω terminator at the end of the chain. Never use Y-splitter cables, this simply won’t work!
Make sure that all units are connected to the mains. Each projector in the chain needs to have its proper start address so it knows which commands from the
controller it has to decode. In the section HOW TO SETUP you will learn how to set the DMX addresses. If for example you use the 2 channel DMX mode, a possible address setup could be: unit1 = 001 ~ unit2 = 003 ~ unit3 = 005 ~ unit4 = 007 ~ etc.
BRITEQ® 4/39 COB PAR56-100
ENGLISH USER MANUAL
HOW TO SETUP:
MAIN MENU:
To select any of the menu options, press the MODE button (or UP/DOWN buttons) up to when the
required option is shown on the display.
Select the function with the ENTER button. Use DOWN and UP button to choose the desired value. Once the required value is selected, press the ENTER button to select.
DMX512 Address Setting Used to set the start address in a DMX setup.
Press the MODE button until DMX ADDR is
shown on the display.
Press the ENTER button to select. Use DOWN and UP buttons to change the
“xxx” DMX512 address.
Once the correct address is shown on the
display, press the ENTER button to confirm.
DMX Channel Mode
The unit has 2 different DMX channel modes. With this function you can choose the DMX mode you want to use. Refer to the DMX­charts to see the differences.
Press the MODE button until CH.MODE is
shown on the display.
Press the ENTER button to select. Use DOWN and UP button to select one of
the available channel modes.
Once the mode is selected, press the ENTER
button to confirm.
SLAVE MODE Used to set the unit in slave mode when you want to synchronize the output with the master unit. (when no controller is used and the first unit is running as master)
Press the MODE button until SLAVE MODE is
shown on the display.
Press the ENTER button to select.
MASTER MODE Used to set the light output while the projector is working in standalone (master) mode.
Press the MODE button until MASTER is shown on the display. Press the ENTER button to select. Use DOWN and UP buttons to change the light output from 000 to 255. (or from 000 to 100%) Once the desired light output is shown on the display, press the ENTER button to confirm.
DIMMER RESPONSE Used to select the dimmer mode you want to use.
Press the MODE button until DIMCURVE is shown on the display. Press the ENTER button to select. Use DOWN and UP buttons to select the dimmer mode you want to use:
BRITEQ® 5/39 COB PAR56-100
ENGLISH USER MANUAL
Once the correct mode is shown on the display, press the ENTER button to confirm.
Note: SQUARE is the best choice for smooth dimming of LED lighting.
LAMP BEHAVIOR Used to select the behavior of the projector while it is dimmed
Press the MODE button until BEHAVIOR is shown on the display. Use DOWN and UP buttons to toggle between:
LED: the projector reacts instantly (without any delay) to the DMX-control signal.  HALOGEN: the projector imitates the behavior of a traditional halogen lamp. The afterglow effect
introduces a certain delay in the reaction time of the projector. Dimming will also be a little smoother.
“NO DMX” BEHAVIOR (BLACKOUT MODE) Used to select the behavior of the projector when DMX fails (no DMX detected).
Press the MODE button until NO DMX is shown on the display. Use DOWN and UP buttons to toggle between:
 BLACKOUT: output turns black while no DMX is detected.  FREEZE: output based on the last valid DMX-signal is kept on the projector.
Note: as soon as the input detects a DMX-signal, blackout or freeze mode will be cancelled.
LOCKING MODE Used to lock the control panel against unauthorized altering of the settings.
Press the MODE button until LOCKING is shown on the display. Use DOWN and UP buttons to toggle between:
OFF: the controls are always available.  ON: after about 30 seconds the controls are automatically locked to avoid unauthorized altering of the
settings in the setup menu. To unlock the controls press the following buttons in the correct order: UP, DOWN, UP, DOWN, ENTER.
CHECKING THE FIRMWARE Used to check the current firmware in the unit.
Press the MODE button until FIRMWARE is shown on the display The current software version is shown on the display.
Note: you can always check the download zone of the product page on our website. If a higher software version is available, it can be uploaded using a special firmware upload device. Further instructions for upgrading are included with the downloaded software.
OPERATING INSTRUCTIONS
Note: when the projector is switched on the display shows “UPDATE WAIT …” This message informs you
that IF you want to upgrade the firmware, you should do it while this message is shown on the display. For normal use you can ignore this message completely.
A. Standalone 1unit:
Just connect the projector to the mains. Select menu option “MASTER” to set the desired light output. Refer to chapter HOW TO SETUP to learn how to set the other menu options.
B. Two or more units in master/slave setup:
Connect the units together. Refer to the chapter “electrical installation” to learn how to do this. Select menu option “MASTER” to set the desired light output on the master (the first projector in the
DMX chain)
Set all the other projectors in SLAVE mode The projectors will now follow the settings of the master projector so they all work synchronously.
C. Controlled by universal DMX-controller:
Connect all units together. Refer to the chapter “Electrical installation for two or more units in DMX-
mode” to learn how to do this (don’t forget to address all units properly!)
Connect all units to the mains and turn on the DMX controller.
Since each unit has its own DMX-address, you can control them individually. Remember that each unit
BRITEQ® 6/39 COB PAR56-100
ENGLISH USER MANUAL
Channel:
Value:
Function:
Remarks:
1
000-255
Master dimmer (0-100%)
Channel:
Value:
Function:
Remarks:
1
000-255
Master dimmer (0-100%)
2
000-005
Open
No strobe
006-255
Increasing strobe speed
006 = slow 255 = fast
uses 1 or 2 DMX-channels, depending on the DMX-mode you have selected in the menu. See the different DMX charts below:
DMX Chart for the 1 channel DMX-Mode
DMX Chart for the 2 channel DMX-Mode
MAINTENANCE
Make sure the area below the installation place is free from unwanted persons during servicing. Switch off the unit, unplug the mains cable and wait until the unit has been cooled down.
During inspection the following points should be checked:
All screws used for installing the device and any of its parts should be tightly fastened and may not be
corroded.
Housings, fixations and installations spots (ceiling, truss, suspensions) should be totally free from any
deformation.
When an optical lens is visibly damaged due to cracks or deep scratches, it must be replaced. The mains cables must be in impeccable condition and should be replaced immediately when even a
small problem is detected.
In order to protect the device from overheat the cooling fans (if any) and ventilation openings should be
cleaned monthly.
The interior of the device should be cleaned annually using a vacuum cleaner or air-jet. The cleaning of internal and external optical lenses and/or mirrors must be carried out periodically to
optimize light output. Cleaning frequency depends on the environment in which the fixture operates: damp, smoky or particularly dirty surroundings can cause greater accumulation of dirt on the unit’s optics.
Clean with a soft cloth using normal glass cleaning products. Always dry the parts carefully.
Attention: We strongly recommend internal cleaning to be carried out by qualified personnel!
SPECIFICATIONS
Mains Input: 110-250Vac, 50/60Hz Power consumption: 130 Watt Fuse: 250V 2A slow blow (20mm glass) Sound Control: none DMX connections: XLR 3pin LEDs: 100W COB warm white: 3200K, CRI = 85
100W COB cold white: 5600K, CRI = 75
Beam angle: 60° Size: see drawing Weight: 2,9 kg
Every information is subject to change without prior notice
You can download the latest version of this user manual on our website: www.briteq-lighting.com
BRITEQ® 7/39 COB PAR56-100
FRANCAIS GUIDE DUTILISATION
GUIDE D'UTILISATION
Nous vous remercions d'avoir acheté ce produit BRITEQ®. Pour tirer pleinement profit de toutes les possibilités du produit et pour votre propre sécurité, lisez ces instructions très attentivement avant d'utiliser cet appareil.
CARACTÉRISTIQUES
Cet appareil ne produit pas d'interférences radio. Ce produit répond aux exigences des directives européennes et nationales actuelles. La conformité a été établie et les déclarations et documents correspondants ont été déposés par le fabricant. Cet appareil a été conçu pour produire un effet d'éclairage décoratif et est utilisé dans les systèmes de jeu de lumière. Projecteur à réflecteur parabolique en version LED, parfait pour les salles d'exposition, magasins, stands
d'exposition, la location d'éclairage...
Doté d'une puissante LED COB blanche 100 W dans une structure PAR classique Disponible en 2 températures de couleur :
WW (blanc chaud) : 3200 K pour une ambiance chaude et confortable
CW (blanc froid) : 5600 K lumière du jour, parfait pour les salles d'exposition, magasins et TV/vidéo Écran LCD de sélection des différents modes de fonctionnement :
Autonome (maître) : définir le gradateur + l'effet stroboscopique (si nécessaire)
Mode maître/esclave : connecter plusieurs projecteurs ensemble, le premier projecteur commande les
autres.
Piloté par DMX, 1 canal : gradateur
Piloté par DMX, 2 canaux : gradateur, effet stroboscopique Comportement des lampes au choix : lampe halogène (lente) ou LED (rapide) Quatre courbes de variation de l'intensité : linéaire, carré, carré inversé, courbe en S En cas d'échec DMX, le mode « tout éteint » ou « maintien » resteront disponibles. Grand angle de faisceau 60° pour une projection uniforme. Refroidissement par ventilateur à très faible niveau sonore. Le porte-filtre permet d'ajouter des filtres de couleur en option. Finition noire ou argentée disponible
AVANT UTILISATION
Avant d'utiliser cet appareil, vérifiez s'il n'a pas été endommagé durant le transport. En cas de dommages,
n'utilisez pas l'appareil et consultez immédiatement votre revendeur.
Important : Cet appareil est expédié de notre usine en parfait état et bien emballé. Il est absolument
nécessaire que l'utilisateur suive strictement les instructions et les avertissements de sécurité se trouvant dans ce manuel. Tout dommage dû à une mauvaise manipulation n'est pas garanti. Le revendeur n'accepte aucune responsabilité pour tous les défauts et problèmes dus au non-respect de ce manuel.
Conservez ce manuel dans un endroit sûr pour toute consultation future. Si vous vendez l'appareil,
assurez-vous de joindre ce manuel.
Vérifiez le contenu :
Vérifiez que l'emballage contient les éléments suivants :
Instructions d'utilisation COB PAR56-100CW (5600 K) ou COB PAR56-100WW (3200 K) Porte-filtre
BRITEQ® 8/39 COB PAR56-100
FRANCAIS GUIDE DUTILISATION
ATTENTION : Pour réduire le risque de choc électrique, ne retirez pas le panneau supérieur. L'appareil ne contient aucun composant réparable par l'utilisateur. Confiez toute réparation à un personnel qualifié uniquement.
Le symbole de l'éclair à l'intérieur d'un triangle équilatéral, est destiné à alerter l'utilisateur de la présence de « tensions dangereuses » non isolées à l'intérieur de l'appareil, d'une magnitude pouvant constituer un risque d'électrocution.
Le symbole du point d'exclamation dans un triangle équilatéral sert à avertir l'utilisateur que d'importants conseils d'utilisation et de maintenance sont fournis dans la documentation accompagnant l'appareil.
Ce symbole signifie : pour usage intérieur uniquement
Ce symbole signifie : Lisez les instructions
Ce symbole signifie : Appareil de classe de sécurité I
Ce symbole détermine : la distance minimale requise avec les objets éclairés. La distance minimale entre la sortie de lumière et la surface éclairée doit être supérieure à un « x » mètre
Cet appareil n'est pas adapté pour un montage direct sur des surfaces normalement inflammables. (ne convient que pour le montage sur surfaces non combustibles)
ATTENTION : Ne fixez pas votre regard sur une lampe allumée. Peut être nocif pour les yeux.
INSTRUCTIONS DE SÉCURITÉ :
Pour protéger l'environnement, essayez de recycler autant que possible les matériaux d'emballage. Pour éviter tout incendie ou électrocution, n'exposez pas cet appareil à la pluie ou à l'humidité. Pour éviter une formation de condensation interne, laissez l'appareil s'adapter à la température ambiante
quand vous le mettez dans une pièce chaude après le transport. La condensation empêche parfois l'appareil de fonctionner à plein rendement ou peut même causer des dommages.
Cet appareil est destiné à un usage intérieur seulement. Ne placez pas d'objets métalliques et ne renversez pas de liquides à l'intérieur de l'appareil. Un choc
électrique ou un dysfonctionnement peut en résulter. Si un corps étranger pénètre dans l'appareil, débranchez immédiatement le cordon d'alimentation de la prise secteur.
Placez l'appareil dans un endroit bien aéré, loin de tout matériau et/ou liquide inflammable. L'appareil doit
être fixé à au moins 50 cm des murs environnants.
Ne couvrez pas les ouvertures de ventilation, cela pourrait entraîner une surchauffe. Évitez une utilisation dans des environnements poussiéreux et nettoyez l'appareil régulièrement. Gardez l'appareil loin de la portée des enfants. Les personnes inexpérimentées ne doivent pas utiliser cet appareil. La température ambiante de fonctionnement maximale est de 40°C. N'utilisez pas cet appareil à des
températures ambiantes plus élevées.
Assurez-vous qu'aucune personne étrangère ne se trouve dans la zone en dessous de l'emplacement
d'installation durant le montage, le démontage et l'entretien.
Laissez environ 10 minutes à l'appareil pour refroidir avant de commencer l'entretien. Débranchez toujours l'appareil lorsqu'il ne va pas être utilisé pendant une longue période ou avant de
commencer l'entretien.
L'installation électrique doit être effectuée par du personnel qualifié, conformément à la réglementation en
matière de sécurité électrique et mécanique dans votre pays.
Vérifiez que la tension secteur n'est pas supérieure à celle indiquée sur l'appareil. Le cordon d'alimentation doit toujours être en parfait état. Éteignez immédiatement l'appareil dès que le
cordon d'alimentation est écrasé ou endommagé. Il doit être remplacé par le fabricant, son agent de service ou une personne de même qualification afin d'éviter tout danger.
Ne laissez jamais le cordon d'alimentation entrer en contact avec d'autres câbles ! Ce luminaire doit être mis à la terre pour être conforme à la réglementation en matière de sécurité. Ne connectez pas l'appareil à un variateur de lumière. Utilisez toujours un câble de sécurité approprié et certifié lors de l'installation de l'appareil. Afin d'éviter un choc électrique, n'ouvrez aucun panneau. L'appareil ne contient aucun composant
réparable par l'utilisateur.
BRITEQ® 9/39 COB PAR56-100
FRANCAIS GUIDE DUTILISATION
Ne réparez jamais un fusible et ne court-circuitez jamais le porte-fusible. Remplacez toujours un fusible
endommagé par un fusible du même type ayant les mêmes spécifications électriques !
En cas de sérieux problèmes de fonctionnement, cessez d'utiliser l'appareil et contactez immédiatement
votre revendeur.
Le boîtier et l'objectif doivent être remplacés s'ils sont visiblement endommagés. Utilisez l'emballage d'origine pour transporter l'appareil. Pour des raisons de sécurité, il est interdit d'apporter des modifications non autorisées à l'appareil.
Important : Ne regardez jamais directement la source de lumière ! N'utilisez pas le jeu de lumière en présence de personnes souffrant d'épilepsie.
DESCRIPTION :
1. ATTACHES DU PORTE-FILTRE : Permet d'installer les filtres de couleur, etc.
2. SUPPORT : avec molette pour attacher l'appareil et un trou pour crochet de suspension.
3. ENTRÉE DMX : connecteur XLR 3 broches mâle pour connecter le projecteur au contrôleur DMX ou à
l'unité précédente dans la chaîne DMX.
4. SORTIE DMX : connecteur XLR 3 broches femelle pour connecter le projecteur à l'unité suivante dans la
chaîne DMX.
5. L'écran affiche les différents menus et les fonctions sélectionnés.
6. Touche BAS : pour diminuer les valeurs affichées à l'écran.
7. Touche HAUT : pour augmenter les valeurs affichées à l'écran.
8. Touche ENTER : pour confirmer votre choix ou pour accéder au mode configuration d'une fonction.
9. Touche MODE : pour parcourir les différentes fonctions du menu
10. Entrée d'alimentation secteur : équipé d'un câble d'alimentation secteur de 1,3 m.
11. PORTE-FUSIBLE : remplacez toujours un fusible endommagé par un fusible du même type ayant les
mêmes spécifications électriques !
MONTAGE AU PLAFOND
Important : L'installation ne doit être effectuée que par un personnel qualifié. Une mauvaise
installation peut entraîner des blessures et/ou des dommages graves. Un montage au plafond exige une grande expérience ! Les limites de charge de fonctionnement doivent être respectées, des matériels d'installation certifiés doivent être utilisés, l'appareil installé doit être inspecté régulièrement pour vérifier les conditions de sécurité.
Assurez-vous qu'aucune personne étrangère ne se trouve dans la zone en dessous de l'emplacement
d'installation durant le montage, le démontage et l'entretien.
L'appareil doit être installé hors de portée des personnes, loin des passages et des endroits où des
personnes peuvent aller et venir, et s'asseoir.
Avant de soulever l'appareil, assurez-vous que le point de suspension peut supporter une charge d'au
moins 10 fois le poids de l'appareil.
Lors de l'installation de l'appareil, utilisez toujours un câble de sécurité certifié qui peut supporter 12 fois le
poids de l'appareil. Ce support de suspension de sécurité secondaire doit être installé de manière à ce
BRITEQ® 10/39 COB PAR56-100
FRANCAIS GUIDE DUTILISATION
qu'aucune partie de l'installation ne puisse tomber de plus de 20 cm si le support principal lâche.
L'appareil doit être bien fixé, un montage balançant est dangereux et ne doit pas être envisagé ! Ne couvrez pas les ouvertures de ventilation, cela pourrait entraîner une surchauffe. L'opérateur doit s'assurer que la sécurité relative à l'installation et les conditions techniques sont
approuvées par un expert avant d'utiliser l'appareil pour la première fois. Les installations doivent être inspectées chaque année par une personne qualifiée pour être sûr que la sécurité est toujours optimale.
INSTALLATION ÉLECTRIQUE
Important : L'installation électrique doit être effectuée par du personnel qualifié, conformément à la réglementation en matière de sécurité électrique et mécanique dans votre
pays. Installation électrique d'une unité autonome :
Insérez le câble d'alimentation secteur. L'appareil démarre immédiatement avec le dernier mode
sélectionné.
Reportez-vous au chapitre COMMENT CONFIGURER pour apprendre comment basculer entre les
différents modes de fonctionnement.
Installation électrique de deux ou plusieurs unités en maître / esclave :
Connectez plusieurs unités entre elles en utilisant de bons câbles de qualité microphone symétrique.
L'unité qui n'a pas de câble connecté à son entrée DMX est l'unité maître, les autres sont des unités esclave.
Assurez-vous que toutes les unités sont branchées au secteur. Reportez-vous au chapitre COMMENT CONFIGURER pour plus d'informations. C'est fait !
Installation électrique de deux ou plusieurs unités en mode DMX :
Le protocole DMX est largement utilisé pour contrôler des équipements lumineux multifonctions au
moyen d'un signal à haute vitesse. Vous devez mettre en chaîne votre contrôleur DMX avec toutes les unités connectées par un câble symétrique de bonne qualité.
Pour éviter un comportement anormal des effets de lumière, à cause des
interférences, vous devez utiliser un terminateur de 90 Ω à 120 Ω à la fin de la
chaîne. N'utilisez jamais de séparateurs de câbles en Y, cela ne fonctionne pas !
Assurez-vous que toutes les unités sont branchées au secteur. Chaque projecteur dans la chaîne doit avoir sa propre adresse et donc gère les
commandes que le contrôleur envoie. Dans la section COMMENT CONFIGURER vous apprendrez comment configurer les adresses DMX. Si par exemple vous utilisez le mode DMX 2 canaux, un réglage de l'adresse possible pourrait être : unité1 = 001 ~ unité2 = 003 ~ unité3 = 005 ~ unité4 = 007 ~ etc.
BRITEQ® 11/39 COB PAR56-100
FRANCAIS GUIDE DUTILISATION
COMMENT CONFIGURER :
MENU PRINCIPAL :
Pour sélectionner une option du menu, appuyez sur la touche MODE (ou touche HAUT/BAS) jusqu'à ce
que l'option voulue s'affiche sur l'écran.
Utilisez la touche ENTER pour sélectionner la fonction. Utilisez les touches BAS et HAUT pour choisir la valeur souhaitée. Une fois la valeur voulue sélectionnée, appuyez sur la touche ENTER pour valider.
Configuration de l'adresse DMX512 Permet de définir l'adresse de début dans une configuration DMX.
Appuyez sur la touche MODE jusqu'à ce que
DMX ADDR s'affiche à l'écran.
Appuyez sur la touche ENTER pour
sélectionner.
Utilisez les touches BAS et HAUT pour
changer l'adresse « xxx » DMX512.
Une fois que la bonne adresse apparaît à
l'écran, appuyez sur la touche ENTER pour confirmer.
Mode canal DMX L'unité offre 2 différents modes canal DMX. Cette fonction permet de sélectionner le mode DMX à utiliser. Reportez-vous au tableau DMX pour voir les différences.
Appuyez sur la touche MODE jusqu'à ce que
CH.MODE s'affiche à l'écran.
Appuyez sur la touche ENTER pour
sélectionner.
Utilisez les touches BAS et HAUT pour
sélectionner un des modes canal disponibles.
Une fois que le mode est sélectionné,
appuyez sur la touche ENTER pour confirmer.
MODE ESCLAVE Permet de définir l'unité en mode esclave quand vous souhaitez synchroniser la sortie avec l'unité maître. (quand aucun contrôleur n'est utilisé, la première unité agit en tant qu'unité maître)
Appuyez sur la touche MODE jusqu'à ce que
SLAVE MODE s'affiche à l'écran.
Appuyez sur la touche ENTER pour sélectionner.
MODE MAÎTRE Permet de régler l'intensité lumineuse alors que le projecteur fonctionne en mode autonome (maître).
Appuyez sur la touche MODE jusqu'à ce que MASTER s'affiche à l'écran. Appuyez sur la touche ENTER pour sélectionner. Utilisez les touches BAS et HAUT pour modifier l'intensité lumineuse de 000 à 255. (ou de 000 à 100%) Une fois que l'intensité lumineuse souhaitée s'affiche à l'écran, appuyez la touche ENTER pour confirmer.
MODE DE FONCTIONNEMENT DU GRADATEUR Permet de sélectionner le mode gradateur à utiliser.
Appuyez sur la touche MODE jusqu'à ce que DIMCURVE s'affiche à l'écran. Appuyez sur la touche ENTER pour sélectionner. Utilisez les touches BAS et HAUT pour sélectionner le mode gradateur à utiliser.
BRITEQ® 12/39 COB PAR56-100
Loading...
+ 30 hidden pages