ENGLISH |
OPERATION MANUAL |
|
|
OPERATION MANUAL
Thank you for buying this Briteq® product. To take full advantage of all possibilities and for your own safety, please read these operating instructions very carefully before you start using this unit.
FEATURES
This unit is radio-interference suppressed. This product meets the requirements of the current European and national guidelines. Conformity has been established and the relevant statements and documents have been deposited by the manufacturer.
Cost effective LED theater spot with manual 10° ~ 50° zoom.
Not only for use in theatres but also perfect for showrooms, shops, exhibition booths, rental, …
The powerful 100W white COB makes it a perfect replacement for a traditional 1000W halogen theater spot: max 7800 lux @2m (beam angle: 10°)
No more heavy and expensive dimmer packs needed!
Color temperature 3200K with high CRI-factor: 85 for natural colors
LCD-display to select different working modes:
Standalone (master) Mode : set dimmer + strobe (if needed)
Master/slave mode: connect several projectors together, the first projector controls the others.
DMX-controlled, 1CH: dimmer
DMX-controlled, 2CH: dimmer, strobe
Selectable lamp behavior: halogen lamp (slow) or led (fast)
Four dimmer curves: linear, square, inverse square, S-curve
In case of DMX failure you can choose between blackout and freeze mode.
Partly extruded black anodized aluminium housing with strong bracket
Neutrik PowerCon in/outputs: easy daisy chaining of several units.
Both 3pin & 5pin DMX in/outputs for maximum compatibility
Forced very low noise fan cooling
Color frame for use of color filters and barn doors included
BEFORE USE
Before you start using this unit, please check if there’s no transportation damage. Should there be any, do not use the device and consult your dealer first.
Important: This device left our factory in perfect condition and well packaged. It is absolutely necessary for the user to strictly follow the safety instructions and warnings in this user manual. Any damage caused by mishandling is not subject to warranty. The dealer will not accept responsibility for any resulting defects or problems caused by disregarding this user manual.
Keep this booklet in a safe place for future consultation. If you sell the fixture, be sure to add this user manual.
Check the contents:
Check that the packing contains the following items:
Operating instructions
BT-THEATRE 100EC MK2
PowerCON mains cable
BRITEQ® |
1/35 |
BT-THEATRE 100EC MK2 |
ENGLISH |
OPERATION MANUAL |
|
|
SAFETY INSTRUCTIONS:
CAUTION: To reduce the risk of electric shock, do not remove the top cover. No user-serviceable parts inside. Refer servicing to qualified service personnel only.
The lightning flash with arrowhead symbol within the equilateral triangle is intended to alert the use or the presence of un-insulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock.
The exclamation point within the equilateral triangle is intended to alert the user to the presence of important operation and maintenance (servicing) instructions in the literature accompanying this appliance.
This symbol means: indoor use only
This symbol means: Read instructions
This symbol determines: the minimum distance from lighted objects. The minimum distance between light-output and the illuminated surface must be more than 1 meters
The device is not suitable for direct mounting on normally flammable surfaces. (suitable only for mounting on non-combustible surfaces)
CAUTION: Do not stare at operating lamp. May be harmful to the eyes.
To protect the environment, please try to recycle the packing material as much as possible.
To avoid condensation to be formed inside, allow the unit to adapt to the surrounding temperatures when bringing it into a warm room after transport. Condense sometimes prevents the unit from working at full performance or may even cause damages.
Don’t place metal objects or spill liquid inside the unit. Electric shock or malfunction may result. If a foreign object enters the unit, immediately disconnect the mains power.
Locate the fixture in a well ventilated spot, away from any flammable materials and/or liquids. The fixture must be fixed at least 50cm from surrounding walls.
Don’t cover any ventilation openings as this may result in overheating.
Prevent use in dusty environments and clean the unit regularly.
Keep the unit away from children.
Inexperienced persons should not operate this device.
Maximum safe ambient temperature is 40°C. Don’t use this unit at higher ambient temperatures.
Make sure the area below the installation place is free from unwanted persons during rigging, de-rigging and servicing.
Allow the device about 10 minutes to cool down before to start servicing.
Always unplug the unit when it is not used for a longer time or before to start servicing.
The electrical installation should be carried out by qualified personal only, according to the regulations for electrical and mechanical safety in your country.
Check that the available voltage is not higher than the one stated on the unit.
The power cord should always be in perfect condition. Switch the unit immediately off when the power cord is squashed or damaged. It must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.
Never let the power-cord come into contact with other cables!
This fixture must be earthed in order to comply with safety regulations.
Don’t connect the unit to any dimmer pack.
Always use an appropriate and certified safety cable when installing the unit.
In order to prevent electric shock, do not open the cover. There are no user serviceable parts inside.
Never repair a fuse or bypass the fuse holder. Always replace a damaged fuse with a fuse of the same type and electrical specifications!
In the event of serious operating problems, stop using the fixture and contact your dealer immediately.
The housing and the lenses must be replaced if they are visibly damaged.
Please use the original packing when the device is to be transported.
Due to safety reasons it is prohibited to make unauthorized modifications to the unit.
Important: Never look directly into the light source! Don’t use the effect in the presence of persons suffering from epilepsy.
BRITEQ® |
2/35 |
BT-THEATRE 100EC MK2 |
ENGLISH |
OPERATION MANUAL |
|
|
DESCRIPTION:
1.MAINS INPUT: equipped with original Neutrik PowerCON®. Connect the supplied mains cable or any PowerCon® extension cable here.
2.MAINS OUTPUT: used to daisy chain the power to several other projectors. Always pay attention to the maximum load while adding projectors! Special Multi cables (PowerCON® + DMX XLR-cables are optionally available: see our website!)
3.MAINS FUSE: protects the unit in case of electrical problems, always use the prescribed fuse!
4.DMX IN/OUT: both 3pin and 5pin in/outputs are available to daisy chain the projector with other units that will be controlled by a DMX-controller.
5.DISPLAY & BUTTONS: Backlit alphanumeric LCD-display and waterproof touch keys to select different options of the setup menu:
MENU-button: used to browse the different menu options or to exit a menu option.
DOWN-button: used to go to the next menu option or to decrease a parameter value.
UP-button: used to go to the previous menu option or to increase a parameter value.
ENTER-button: used to select a menu option or confirm a setting.
6.FOCUS KNOB: used to adjust the beam angle between 10° and 50°.
7.HANGING BRACKET: with knobs on both sides to fasten the unit.
8.SAFETY HOLE: used to attach a safety cable when the unit is rigged, see paragraph “overhead rigging”.
9.COLOR FRAME: used to fix color gels in front of the lens. The clip is used to keep the color frame in place.
10.BARN DOORS: they facilitate shaping of the beam of light from the fixture, and prevent the distinctive scatter of light created by the Fresnel lens from spilling into areas where it is not wanted, such as the eyes of audience members. Just rotate the barndoor leafs in the desired position.
OVERHEAD RIGGING
Important: The installation must be carried out by qualified service personal only. Improper installation can result in serious injuries and/or damage to property. Overhead rigging requires extensive experience! Working load limits should be respected, certified installation materials should be used, the installed device should be inspected regularly for safety.
Make sure the area below the installation place is free from unwanted persons during rigging, de-rigging and servicing.
Locate the fixture in a well ventilated spot, far away from any flammable materials and/or liquids. The fixture must be fixed at least 50cm from surrounding walls.
The device should be installed out of reach of people and outside areas where persons may walk by or be seated.
Before rigging make sure that the installation area can hold a minimum point load of 10times the device’s weight.
BRITEQ® |
3/35 |
BT-THEATRE 100EC MK2 |
ENGLISH |
OPERATION MANUAL |
|
|
Always use a certified safety cable that can hold 12times the weight of the device when installing the unit. This secondary safety attachment should be installed in a way that no part of the installation can drop more than 20cm if the main attachment fails.
The device should be well fixed; a free-swinging mounting is dangerous and may not be considered!
Don’t cover any ventilation openings as this may result in overheating.
The operator has to make sure that the safety-relating and machine-technical
installations are approved by an expert before using them for the first time. The installations should be inspected every year by a skilled person to be sure that safety is still optimal.
ELECTRICAL INSTALLATION + ADDRESSING
Important: The electrical installation should be carried out by qualified personal only, according to the regulations for electrical and mechanical safety in your country.
Master / Slave mode:
Connect the projectors together as shown on the drawing. Please refer to the paragraph “SETUP MENU” to setup the master. You can also switch the IR-remote on the master to ON and use the included IR-remote. All slaves must be set to SLAVE-mode. You can put as many slaves as you like on condition that the overall power consumption on the power line stays under 10A (2300W).
IMPORTANT: make sure that no DMX-controller is connected, this will result in unexpected behavior!
Electrical installation for two or more units in DMX-mode:
The DMX-protocol is a widely used high speed signal to control intelligent light equipment. You need to
“daisy chain” your DMX controller and all the connected units.
Use the supplied DMX input conversion cable (IP-cabling to XLR-male) to connect the first unit in the line to the controller.
Pin layout XLR-3pin: Pin1 = GND ~ Pin2 = Negative signal (-) ~ Pin3 = Positive signal
Pin layout XLR-5pin: Pin1 = GND ~ Pin2 = Negative signal (-) ~ Pin3 = Positive signal
(+)~ Pins4+5 not used.
To prevent strange behavior of the light effects, due to interferences, you must use a
90Ω to 120Ω terminator at the end of the chain. Never use Y-splitter cables, this simply won’t work!
Make sure that all units are connected to the mains.
Each unit in the chain needs to have its proper starting address so it knows which commands from the controller it has to decode. In the next section you will learn how to set the DMX addresses.
BRITEQ® |
4/35 |
BT-THEATRE 100EC MK2 |
ENGLISH |
OPERATION MANUAL |
|
|
HOW TO SETUP:
For both models all points are identical, except for the display messages: displays are shown on the left side.
To select any of the functions, press the MODE button until the required function is shown on the display or use the DOWN and UP buttons to browse the menu.
Select the function with the ENTER button.
Use DOWN and UP buttons to change the values.
Once the required value is selected, press the ENTER button to confirm.
DMX ADDR
Used to set the desired DMX-address.
Press the MODE button until the desired function is showing on the display.
Press the ENTER button: the values can be changed
Use DOWN and UP buttons to select the desired DMX512 address. The last occupied DMX-address is also shown: makes it easier to set the address of the next unit in the chain.
Once the correct address shows on the display, press the ENTER button to save it.
Note: on RDM-compatible controllers this option can also be remotely set.
CH. MODE
Used to set the desired channel mode.
Press the MODE button until the desired function is showing on the display.
Press the ENTER button: the values can be changed
Use DOWN and UP buttons to select the desired mode:
CH:01 master dimmer
CH:02 strobe + master dimmer
Once the correct option shows on the display, press the ENTER button to save it.
Remark: on RDM-compatible controllers this option can also be remotely set.
SLAVE MODE
Used to set the projector as slave in a master/slave setup.
Press the MODE button until SLAVE MODE is showing on the display.
MASTER DIM
Used to set the master dimmer while used as master.
Press the MODE button until the desired function is showing on the display.
Press the ENTER button: the values can be changed
Use DOWN and UP buttons to select the desired level for the master dimmer. (please note that the last selected static color will be used to set the value)
Once you have the desired level, press the ENTER button to save it.
Note: the setting of this option has NO effect while the projector is used as SLAVE or in DMX-mode.
DIMMER CURVE
Used to set the dimmer curve of the master dimmer.
Press the MODE button until the desired function is showing on the display.
Press the ENTER button: the values can be changed
Use DOWN and UP buttons to selected the desired curve:
BRITEQ® |
5/35 |
BT-THEATRE 100EC MK2 |
ENGLISH |
|
|
OPERATION MANUAL |
|||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Once you have the desired curve, press the ENTER button to save it.
LAMP BEHAVIOR
Used to select the reaction time of the projector.
Press the MODE button until the desired function is showing on the display.
Press the ENTER button: the values can be changed
Use DOWN and UP buttons to select the desired mode:
LED |
The projector follows the instructions instantly, no delay. |
HALOGEN The projector imitates the behavior of a halogen lamp (slower reaction time).
Once the correct option shows on the display, press the ENTER button to save it.
LOCKING MODE
Used to lock the setup menu against unwanted altering of the settings.
Press the MODE button until the desired function is showing on the display.
Press the ENTER button: the values can be changed
Use DOWN and UP buttons to select the desired mode:
OFF The setup menu can be used at any time.
ON After a short time the setup menu locks automatically, the display shows “ LOCKED ***** ”.
Unlock the display by pressing the buttons in this order: UP, DOWN, UP, DOWN, ENTER.Once the correct option shows on the display, press the ENTER button to save it.
NO DMX BEHAVIOR
Used to set how the projector reacts when the DMX-signal suddenly disappears.
Press the MODE button until the desired function is showing on the display.
Press the ENTER button: the values can be changed
Use DOWN and UP buttons to select the desired mode:
BLACKOUT output turns black while no DMX is detected.
FREEZE: output based on the last valid DMX-signal is kept on the projector.
Once the correct option shows on the display, press the ENTER button to save it.
Note: as soon as the input detects a DMX-signal, blackout or freeze mode will be cancelled.
FIRMWARE VERSION
Used to show the current version of the firmware.
Press the MODE button until the FIRMWARE is showing on the display.
The firmware of this unit can be upgraded using a special upgrade tool with Windows® software. (separately available from Briteq).
Each time the projector is switched on, the display shows “UPDATE Wait ….”: while this message shows on the display you can start the update using our special upgrade tool. More information about this can be found in the user manual of the upgrade tool and / or our website: www.briteq-lighting.com
RDM FUNCTIONS / REMOTE SETUP
RDM means “Remote Device Management”. This projector works with a brief set of RDM-functions which means that it can setup a bi-directional communication with an RDM-compatible DMX-controller. Some of these functions are briefly explained below, others will be added in the future.
The DMX-controller sends out a “discovery command”, all RDM devices respond and send their unique device ID.
The DMX-controller asks each RDM device for some basic data so it knows which devices are connected. The projector will respond:
Device name: the actual name of the unit
Manufacturer: Briteq®
BRITEQ® |
6/35 |
BT-THEATRE 100EC MK2 |
ENGLISH |
OPERATION MANUAL |
|
|
|
Category: LED Dimmer |
|
|
Firmware: x.x.x.x |
(firmware version of the projector) |
DMX address: xxx (current DMX start address of the projector)
DMX footprint: xx (number of DMX-channels used by the projector)
Personality: xx |
(current personality [or DMX-working mode] used by the projectors) |
The DMX-controller can send certain commands to each RDM device which allow remote setup of the units. Thanks to this the projectors can be setup remotely.
The following functions can be managed remotely:
No more need to take a ladder and set all units one by one!
DMX START ADDRESS: The start address can be set remotely from 001 to xxx.
PERSONALITY: The DMX working mode (DMX-chart) can be set remotely.
These 2 functions make it possible to prepare a complete DMX-patch of all projectors on the DMXcontroller and send these data to all projectors at once. More functions will be added later.
OPERATING INSTRUCTIONS
Note: when the projector is switched on the display shows “UPDATE WAIT …” This message informs you that IF you want to upgrade the firmware, you should do it while this message is shown on the display. For normal use you can ignore this message completely.
A.Standalone 1unit:
Just connect the projector to the mains.
Select menu option “MASTER” to set the desired light output.
Refer to chapter HOW TO SETUP to learn how to set the other menu options.
B.Two or more units in master/slave setup:
Connect the units together. Refer to the chapter “electrical installation” to learn how to do this.
Select menu option “MASTER” to set the desired light output on the master (the first projector in the
DMX chain)
Set all the other projectors in SLAVE mode
The projectors will now follow the settings of the master projector so they all work synchronously.
C.Controlled by universal DMX-controller:
Connect all units together. Refer to the chapter “Electrical installation for two or more units in DMXmode” to learn how to do this (don’t forget to address all units properly!)
Connect all units to the mains and turn on the DMX controller.
Since each unit has its own DMX-address, you can control them individually. Remember that each unit uses 1 or 2 DMX-channels, depending on the DMX-mode you have selected in the menu. See the different DMX charts below:
DMX Chart for the 1 channel DMX-Mode
|
|
Channel: |
|
|
Value: |
|
|
Function: |
|
|
Remarks: |
|
|
|
|
|
|
|
|
|
|
||||
|
1 |
|
000-255 |
|
|
Master dimmer (0-100%) |
|
|
|
|
||
DMX Chart for the 2 channel DMX-Mode |
|
|
|
|
||||||||
|
|
Channel: |
|
|
Value: |
|
|
Function: |
|
|
Remarks: |
|
|
1 |
|
000-255 |
|
|
Master dimmer (0-100%) |
|
|
|
|
||
|
2 |
|
000-005 |
|
|
Open |
|
|
No strobe |
|
||
|
|
006-255 |
|
|
Increasing strobe speed |
|
|
006 = slow 255 = fast |
|
|||
|
|
|
|
|
|
|
|
|
||||
MAINTENANCE
Make sure the area below the installation place is free from unwanted persons during servicing.
Switch off the unit, unplug the mains cable and wait until the unit has been cooled down.
During inspection the following points should be checked:
All screws used for installing the device and any of its parts should be tightly fastened and may not be corroded.
Housings, fixations and installations spots (ceiling, truss, suspensions) should be totally free from any deformation.
BRITEQ® |
7/35 |
BT-THEATRE 100EC MK2 |
ENGLISH |
OPERATION MANUAL |
|
|
When an optical lens is visibly damaged due to cracks or deep scratches, it must be replaced.
The mains cables must be in impeccable condition and should be replaced immediately when even a small problem is detected.
In order to protect the device from overheat the cooling fans (if any) and ventilation openings should be cleaned monthly.
The cleaning of internal and external optical lenses and/or mirrors must be carried out periodically to optimize light output. Cleaning frequency depends on the environment in which the fixture operates: damp, smoky or particularly dirty surroundings can cause greater accumulation of dirt on the unit’s optics.
Clean with a soft cloth using normal glass cleaning products.
Always dry the parts carefully.
Attention: We strongly recommend internal cleaning to be carried out by qualified technician!
SPECIFICATIONS
Mains Input: |
AC 110V - 240V, 50/60Hz |
Power consumption: |
125 Watt max. |
Fuse: |
250V T2A (20mm glass) |
DMX connections: |
3pin + 5pin XLR male / female |
DMX channels used: |
1+2 channels |
Lamp: |
100W warm white COB 3200K |
|
CRI = 85 |
LED Refresh rate: |
1200 Hz |
Beam Angle: |
10° – 50° |
Size: |
see drawing |
Weight: |
6,5 kg |
The information might be modified without prior notice
You can download the latest version of this user manual on our website: www.briteq-lighting.com
BRITEQ® |
8/35 |
BT-THEATRE 100EC MK2 |
FRANÇAIS |
GUIDE D'UTILISATION |
|
|
GUIDE D'UTILISATION
Nous vous remercions d'avoir acheté ce produit Briteq®. Pour tirer pleinement profit de toutes les possibilités du produit et pour votre propre sécurité, lisez ces instructions très attentivement avant d'utiliser cet appareil.
CARACTÉRISTIQUES
Cet appareil ne produit pas d'interférences radio. Ce produit répond aux exigences des directives européennes et nationales actuelles. La conformité a été établie et les déclarations et documents correspondants ont été déposés par le fabricant.
Projecteur théâtre à LED économique avec zoom manuel de 10° à 50°.
Convient également pour les showrooms, magasins, stands d’exposition, location, …
Grace à sa puissante LED COB blanche de 100W white COB il devient le remplaçant idéal du projecteur théâtre traditionnel à lampe halogène de 1000W: max 7800 lux @2m (sous un angle de 10°)
Plus besoin de gradateurs lourds et coûteux!
Température de couleur de 3200K et facteur CRI élevé: 85 pour un rendu des couleurs naturel
Écran LCD pour sélectionner les différents modes:
Mode autonome (maitre): réglez la gradation et la vitesse du stroboscope (si nécessaire)
Mode maitre/esclave: reliez plusieurs projecteurs ensemble, le premier projecteur contrôle les autres.
Contrôlé par 1 canal DMX: gradation
Contrôlé par 2 canaux DMX: gradation, stroboscope
Sélection de la vitesse de réaction de la lampe: lampe halogène (lent) ou LED (rapide)
4 courbes de gradation: linéaire, logarithmique, anti-logarithmique, courbe S
En cas de défaillance du DMX: présélectionnez si le projecteur doit garder la dernière commande ou si il doit passer en mode ‘blackout’.
Boitier en aluminium partiellement extrude, anodisé noir avec une solide attelle de suspension
Entrées / sorties Neutrik PowerCon: chainage facile de plusieurs unités.
Entrées/sorties DMX à 3 broches et à 5 broches pour un maximum de flexibilité
Refroidissement forcé par ventilateur à très faible bruit
Le porte-filtre peut être utilisé pour y poser des gélatines de couleur
AVANT UTILISATION
Avant d'utiliser cet appareil, vérifiez s'il n'a pas été endommagé durant le transport. En cas de dommages, n'utilisez pas l'appareil et consultez immédiatement votre revendeur.
Important : Cet appareil est expédié de notre usine en parfait état et bien emballé. Il est absolument nécessaire que l'utilisateur suive strictement les instructions et les avertissements de sécurité se trouvant dans ce manuel. Tout dommage dû à une mauvaise manipulation n'est pas garanti. Le revendeur n'accepte aucune responsabilité pour tous les défauts et problèmes dus au non-respect de ce manuel.
Conservez ce manuel dans un endroit sûr pour toute consultation future. Si vous vendez l'appareil, assurez-vous de joindre ce manuel.
Vérifiez le contenu :
Vérifiez que le carton contient les éléments suivants :
Instructions d'utilisation
BT-THEATRE 100EC MK2
Câble d’alimentation PowerCON®
BRITEQ® |
9/35 |
BT-THEATRE 100EC MK2 |
FRANÇAIS |
GUIDE D'UTILISATION |
|
|
INSTRUCTIONS DE SÉCURITÉ :
ATTENTION : Pour réduire le risque de choc électrique, ne retirez pas le panneau supérieur. L'appareil ne contient aucun composant réparable par l'utilisateur. Confiez toute réparation à un personnel qualifié uniquement.
Le symbole de l'éclair à l'intérieur d'un triangle équilatéral est destiné à alerter l'utilisateur de la présence de « tensions dangereuses » non isolées à l'intérieur de l'appareil, d'une magnitude pouvant constituer un risque d'électrocution.
Le symbole du point d'exclamation dans un triangle équilatéral sert à avertir l'utilisateur que d'importants conseils d'utilisation et de maintenance sont fournis dans la documentation accompagnant l'appareil.
Ce symbole signifie : pour usage intérieur uniquement
Ce symbole signifie : Lisez les instructions
Ce symbole définit : la distance minimale requise avec les objets éclairés. La distance minimale entre la sortie de lumière et la surface éclairée doit être supérieure à un 1 mètre
Cet appareil n'est pas adapté pour un montage direct sur des surfaces normalement inflammables. (ne convient que pour le montage sur surfaces non combustibles)
ATTENTION : Ne fixez pas votre regard sur une lampe allumée.
Peut être nocif pour les yeux.
Pour protéger l'environnement, essayez de recycler autant que possible les matériaux d'emballage.
Pour éviter une formation de condensation interne, laissez l'appareil s'adapter à la température ambiante quand vous le mettez dans une pièce chaude après le transport. La condensation empêche parfois l'appareil de fonctionner à plein rendement ou peut même causer des dommages.
Ne placez pas d'objets métalliques et ne renversez pas de liquides à l'intérieur de l'appareil. Un choc électrique ou un dysfonctionnement peut en résulter. Si un corps étranger pénètre dans l'appareil, débranchez immédiatement le cordon d'alimentation de la prise secteur.
Placez l'appareil dans un endroit bien aéré, loin de tout matériau et/ou liquide inflammable. L'appareil doit être fixé à au moins 50 cm des murs environnants.
Ne couvrez pas les ouvertures de ventilation, cela pourrait entraîner une surchauffe.
Évitez une utilisation dans des environnements poussiéreux et nettoyez l'appareil régulièrement.
Gardez l'appareil loin de la portée des enfants.
Les personnes inexpérimentées ne doivent pas utiliser cet appareil.
La température ambiante de fonctionnement maximale est de 40°C. N'utilisez pas cet appareil à des températures ambiantes plus élevées.
Assurez-vous qu'aucune personne étrangère ne se trouve dans la zone en dessous de l'emplacement d'installation durant le montage, le démontage et l'entretien.
Laissez environ 10 minutes à l'appareil pour refroidir avant de commencer l'entretien.
Débranchez toujours l'appareil lorsqu'il ne va pas être utilisé pendant une longue période ou avant de commencer l'entretien.
L'installation électrique doit être effectuée par du personnel qualifié, conformément à la réglementation en matière de sécurité électrique et mécanique dans votre pays.
Vérifiez que la tension secteur n'est pas supérieure à celle indiquée sur l'appareil.
Le cordon d'alimentation doit toujours être en parfait état. Éteignez immédiatement l'appareil dès que le cordon d'alimentation est écrasé ou endommagé. Il doit être remplacé par le fabricant, son agent de service ou une personne de même qualification afin d'éviter tout danger.
Ne laissez jamais le cordon d'alimentation entrer en contact avec d'autres câbles !
Ce luminaire doit être mis à la terre pour être conforme à la réglementation en matière de sécurité.
Ne connectez pas l'appareil à un variateur de lumière.
Utilisez toujours un câble de sécurité approprié et certifié lors de l'installation de l'appareil.
Afin d'éviter un choc électrique, n'ouvrez aucun panneau. L'appareil ne contient aucun composant réparable par l'utilisateur.
Ne réparez jamais un fusible et ne court-circuitez jamais le porte-fusible. Remplacez toujours un fusible endommagé par un fusible du même type ayant les mêmes spécifications électriques !
En cas de sérieux problèmes de fonctionnement, cessez d'utiliser l'appareil et contactez immédiatement votre revendeur.
BRITEQ® |
10/35 |
BT-THEATRE 100EC MK2 |
Loading...