Briteq BTX-700BEAM Operation Manual

Download

Page 1

Page 2

Page 3

Please read carefully the instruction manual, which includes

important information about the installation, usage and maintenance.

1. Safety Instruction

WARNING

Please keep this User Guide for future consultation. If you sell the unit to another user, be sure that they also receive this instruction manual.

Important: Damages caused by the disregard of this user manual are not subject to warranty. The dealer will not accept liability for any resulting defects or problems.

 Unpack and check carefully that there is no transportation damage before using the

unit.

 The unit is for indoor use only. Use only in a dry location.  Do install and operate by qualified operator.  Do not allow children to operate the fixture.  Use safety chain when fixing the unit. Handle the unit by carrying its base instead of

head only.

 The unit must be installed in a location with adequate ventilation, at least 50cm from

adjacent surfaces.

 Be sure that no ventilation slots are blocked, otherwise the unit will be overheated.  Before operating, ensure that the voltage and frequency of power supply match the

power requirements of the unit.

 It’s important to ground the yellow/green conductor to earth in order to avoid electric

shock.

 Maximum ambient temperature TA: 40°C. Don’t operate it when the temperature is

higher.

 Don’t connect the device to any dimmer pack.  During initial start-up some smoke or smell may arise. This is a normal process and

does not necessarily mean that the device is defective, and it will decrease gradually within 15 minutes.

 Make sure there are no flammable materials close to the unit while operating to avoid

fire hazard.

 Examine the power wires carefully, replace them immediately if there is any damage.  Unit’s surface temperature may reach up to 85℃. Don’t touch the housing bare-handed

during its operation, and allow about 15 minutes for cooling the unit down before replacing bulb or maintenance as it could be very hot.

 Avoid any inflammable liquids, water or metal objects entering the unit. Once it

happens, cut off the mains power immediately.

 Do not operate in dirty or dusty environment, do clean fixtures regularly.  Do not touch any wire during operation as there might be a hazard of electric shock.  Avoid power wires together twist other cables.  The minimum distance between light output and the illuminated surface must be more

than 2.5 meters.

 Disconnect mains power before fuse/lamp replacement or servicing.  Replace fuse/lamp only with the same type.  In the event of serious operating problem, stop using the unit immediately.  Never turn on and off the unit time after time.  The housing, the lenses, or the ultraviolet filter must be replaced if they are visibly

damaged.

BRITEQ® 1 BTX-700BEAM

Page 4

 Do not open the unit as there are no user serviceable parts inside.  Never try to repair the unit by yourself. Repairs carried out by unskilled people can lead

to damage or malfunction. Please contact the nearest authorized technical assistance center if needed.

 Disconnect the mains power if the fixture is has not been used for a long time.  Do use the original packing materials before transporting it again.

Caution

 To prevent or reduce the risk of electrical shock or fire, do not expose the unit to rain or

moisture.

 Hot lamp explosion hazard. Do not open the unit within 15 minutes after switching off.  Do replace the bulb once it is damaged, deformed or life-expired.  Do not look directly at the light while the bulb is on.  Never touch bulb with bare fingers, as it is very hot after using.  Do not start on the unit without bulb enclosure or when housing is damaged.

Product Items

 User manual  2 x Omega clamps

2. Installation

Unpacking the fixture (for flight case pack only)

1. Stop the flight case via the brake sheet above the wheels.

2. Unlock the lock modules (1) and open the cover board.

3. Prop the cover board with lid bracket.

4. Take out the fixture.

5. Unlock the lock module (2) take out omega clamps.

Installation:

1. Bolt each clamp (1) to the Omega holder with screw and lock nut through the hole in the holder.

2. Fasten the omega holders (2) on the bottom of the base by inserting quick-lock fasteners (3) into the holes of the base and tighten fully clockwise.

3. Hang the fixture to the support (4) through clamp and fasten the screws (5). Fasten the safety cable (6) through the bottom of the base and over the support.

Fig.1 Fig.2

Attention:

 Always ensure that the structure to which you are attaching the unit is secure and is

able to support a weight of 10 times of the unit’s weight.

BRITEQ® 2 BTX-700BEAM

Page 5

 Also always use a safety cable that can hold 12 times of the weight of the unit when

installing the fixture.

 Always ensure that the unit is firmly fixed to avoid vibration and slipping while

operating.

 The equipment must be fixed by professionals. And it must be fixed at a place where is

out of the touch of people and has no one pass by or under it.

3. Technical Specification

Power supply

- AC 100V~240V 50/60Hz

Power Consumption

- 879W (230V)

- 909W (120V)

Fuse

- T 15 A

Lamp

- Philips MSR Gold 700/2 mini FastFit

Battery backup display

- Setting DMX address or other functions without connecting to mains power.

- Battery for LCD display charges automatically when the fixtures connects to the mains power.

- No need to change battery. Wireless control (for the unit with wireless receiver built-in only)

- Wirelessly controlled by W-DMX (option).

- Each W-DMX is sending out 512 channels of DMX.

- License free band of 2.45 GHz

Optical system

- High efficiency optical system, delivering extremely powerful output

- High quality diachronic lenses

- Beam angle: 8°

Movement

- Pan: 540°

- Tilt: 270°

- Pan/Tilt moving speed adjustable.

- Automatic Pan/Tilt correction.

- Easy calibration and maintenance by magnetic home positioning.

- Pan/Tilt position lock for transporting protection.

Shutter/Dimmer

- Blackout, 0~100% smooth dimming, independent shutter and various strobe effect.

Color wheel

- Color wheel: 7 diachronic colors + open.

- Rainbow effect in both directions.

- Easy calibration and maintenance by magnetic home positioning.

CMY

- CMY speed adjustable.

- Optional multiple preset colors and macros available.

Gobo wheel

- Gobo size: Ø26.8mm (Ø24mm for image)

- Gobo Wheel: 7 rotating, index able, easily replaceable gobos + open.

- Easy calibration and maintenance by magnetic home positioning.

BRITEQ® 3 BTX-700BEAM

Page 6

- Module design for easy assembly and service.

Prism

- 3 facets prism with rotating effect.

Frost

- Variable, separate effect.

Cool

- Fan cooled

Protocols

- DMX 512

- Date input/output: 3/5 Pin XLR socket

Weight

- 21.5kgs Dimension

- 447× 369×604 mm

Photometric diagram

BRITEQ® 4 BTX-700BEAM

Page 7

Mode

Mode 1

18-CH

Mode 2

18-CH

Mode 3

25-CH

Pan

Shutter

Pan

Pan Fine

Dimmer

Pan Fine

Tilt

Cyan

Tilt

Tilt Fine

Magenta

Tilt Fine

Pan /Tilt Speed

Yellow

Pan /Tilt Speed

Shutter

Color

Dimmer

Gobo

Dimmer Fine

Color

R-Gobo

Shutter

Cyan

R-Gobo Fine

Color

Magenta

Prism

Cyan

Yellow

R-Prism

Magenta

Preset Color

Pan

Yellow

Gobo

Pan Fine

CMY Speed

R-Gobo

Tilt

Gobo

Prism

Tilt Fine

R-Gobo

R-Prism

Pan /Tilt Speed

R-Gobo Fine

Frost

Prism

Function

R-Prism

R-Prism Fine

Frost

P/T Macro

P/T Macro Speed

Preset Color

Color Macro

Function

DMX Channels

BRITEQ® 5 BTX-700BEAM

Page 8

POWER

Power on

DMX

DMX input present

To enter into move backward or leave the menu

To go backward to move up in the menu

DOWN

To move down in the menu

ENTER

To perform the desired functions

1. Arm

2. Front panel

3. head

4. Tilt lock button (Black)

5. Tilt unlock button (Gray)

6. Pan lock

7. Handle

8. Base

9. Antenna (for XP-700A BEAM WT only)

4. Description

4.1 Description of the fixture

The head can be locked for transportation protection-the tilt lock button (4) is pressed and the pan lock/unlock lever (6) is in lock position. To unlock the head, press the tilt unlock button (5) and move the pan lock/unlock lever (6) to unlock position.

Caution: The head and arm must be unlocked before operation!

4.2 Control Panel

Front view Rear view

,1 Monitor (Batter Back-up display):

○

,2 LED

○

,3 Button

○

,4 Antenna (optional)

○

Receive wireless signal from a wide range

BRITEQ® 6 BTX-700BEAM

Page 9

DANGER!

Install the gobos with the device switched off only.

Unplug from mains before changing gobos!

,5 DMX input/output:

○

For DMX 512 operation, use 3/5-pin XLR plug cable to link the units together

,6 Power Switch:

○

Turns On/Off the power

,7 Power Cable:

○

To connect to the mains supply

,8 Fuse (T 15 A):

○

Protect the unit from damage of over current.

5. Gobo and Lamp

5.1 Inserting/Exchanging rotating gobos

CAUTION: Never unscrew the screws of the rotating gobo as the ball bearing will otherwise be opened!

Please follow the steps below to insert/change rotating gobos

1. Open the cover by loosening the fastening screws on the cover.

2. Push the gobo plate (follow the direction 1) and gently pull out the plate (follow the direction 2).

3. Take out the ring with an appropriate tool. Do not touch the surface of the glass gobo.

4. Remove the original gobo and inset a new one (glazy side towards the lamp). Insert the ring to secure it in the gobo holder.

5. Install the gobo plate back into the gobo wheel. Make sure the gobo plate is installed under the pressure plate.

BRITEQ® 7 BTX-700BEAM

Page 10

In case of replacement of the lamp or maintenance, do not open the fixture within 15 minutes until the unit cools down after switching off.

5.2 Lamp

MSR/ MSD Gold 700/2 miniFastFit

 Because of its high internal pressure, there might be a risk that the Discharge

lamp would explode during operation. The lamp emits intense UV radiation which is harmful to the eyes and skin. The high luminance of the arc can cause severe damage to the retina if you take a close look at the lamp.

 To protect the lamp, always turn off the lamp first (via control panel or DMX

controller) and let the unit run at least five minutes to cool down before switching off the mains supply. Never handle the lamp or luminaries when it is hot.

 Do not touch the bulb with bare hands. If this happens, clean the lamp with

denatured alcohol and wipe it with a lint free cloth before installation.

 The lamp generates UV radiation. Never operate the lamp without appropriate

shielding.

 When lighting up, the lamp operates at high pressure and there is a slight risk of arc

tube rupture. The risk increases with age, temperature and improper handling of the lamp. Do not use the lamp longer than its lifespan.

 Make sure the lamp is located in the center of the reflector for the best projection.

Change Lamp

WARNING

1. Turn off the power.

2. Unscrew the two screws (A), open the lamp cover, turn it to the position as the sketch shown below.

3. Hold the base of the lamp, anticlockwise turn until it is parallel to the groove.

4. Inset a new lamp follow the groove, turn it clockwise to fix the lamp.

5. Tighten the screws (A) to fix the lamp cover.

6. Turn the screws (B) to adjust the lamp position be sure it is located in the center of the reflector for the best projection.

BRITEQ® 8 BTX-700BEAM

Page 11

Lamp 40°C

Present temperature of base CPU is 40°C

001

Present start address

Md.3 25Ch.

Present channel mode is mode 3 (25 channels mode)

Lamp 30°C

Present temperature of lamp is 30°C

Warning signal blinking direct resetting error

6. How To Set The Unit

6.1 Power On Display

Every time you turn on the unit, it will run built-in program to reset all motors to their home position, the display will show as fig.4, you may hear some noises for about 20 seconds. It will show warning sign if it goes wrong during resetting and you can press the MENU button to view the error information. After that the unit will be ready to receive DMX signal and the display will show as fig.5.

Fig.4 Fig.5

Explanation of fig.5:

6.2 Main Function

Turn on the unit, press MENU button into menu mode, press UP and DOWN button until the required function is shown on the monitor. Select the function by ENTER button. Use UP and DOWN button to choose the submenu, press the ENTER button to store and automatically return to the last menu. Press MENU button or let the unit idle one minute to exit menu mode. In the event of disconnecting with mains power, press UP button for one minute to enter into menu mode. Press MENU button or let the unit idle one minute to exit.

The main functions are shown below（the grayed boxes are preset settings）:

BRITEQ® 9 BTX-700BEAM

Page 12

BRITEQ® 10 BTX-700BEAM

Page 13

DMX Functions

Enter menu mode, select DMX Functions, press ENTER button to confirm, use UP and DOWN button to select DMX Address, DMX Channel Mode, View DMX Value or

WDMX Setting.

DMX Address—DMX512 address setting

Select DMX Address, press ENTER button to confirm, the present address will blink on the display, use UP and DOWN button to adjust the address from 0 to 512, press ENTER button to store. Press MENU button back to the last menu or let the unit idle one minute to exit menu mode.

DMX Channel Mode—channel mode

Select DMX Channel Mode, press ENTER button to confirm, present channel mode will blink on the display, use UP and DOWN button to select Mode1 (18 channels mode) or Mode 2 (18 channels mode) or Mode 3 (25 channels mode), press ENTER button to store. Press MENU button back to the last menu or let the unit idle one minute to exit menu mode.

View DMX Value

Select View DMX Value, press ENTER button to confirm. Channel function and its value will show on the display, use UP and DOWN button to view other DMX value. Press MENU button back to the last menu or let the unit idle one minute to exit menu mode.

BRITEQ® 11 BTX-700BEAM

Page 14

WDMX Setting—wireless control setting

(For the unit with wireless receiver built-in only)

Select WDMX Setting, press ENTER button to confirm. Use UP and DOWN button to select Active, Retransmit or Reset Memory, press ENTER button to store. Press MENU button back to the last menu or let the unit idle one minute to exit menu mode.

Active

Select Active, press ENTER button to confirm, use UP and DOWN button to select Yes (wireless control available) or No (wireless control unavailable), press ENTER button to store. Press MENU button back to the last menu or let the unit idle one minute to exit menu mode.

(Set wireless control to be available, the power indicate LED will strobe)

Retransmit

Select Retransmit, press ENTER button to confirm, use UP and DOWN button to select Yes or No, press ENTER button to store. Press MENU button back to the last menu or let the unit idle one minute to exit menu mode.

Reset Memory

Select Reset Memory, press ENTER button to confirm, use UP and DOWN button to select Yes (refuse wireless signal) or No , press ENTER button to store. Press MENU button back to the last menu or let the unit idle one minute to exit menu mode.

Fixture Setting

Enter menu mode, select Fixture Setting, press ENTER button to confirm, use UP and DOWN button to select Pan Inverse, Tile Inverse, BL.O. P/T Moving, BL.O. Color

Change or BL.O. Gobo Change.

Pan Inverse

Select Pan Inverse, press ENTER button to confirm, present mode will blink on the display, use UP and DOWN button to select No (normal) or Yes (pan inverse), press ENTER button to store. Press MENU button back to the last menu or let the unit idle one minute to exit menu mode.

Tilt Inverse Select Tilt Inverse, press ENTER button to confirm, present mode will blink on the display, use UP and DOWN button to select No (normal) or Yes (tilt inverse), press ENTER button to store. Press MENU button back to the last menu or let the unit idle one minute to exit menu mode.

BL.O. P/T Moving—Blackout while pan/tilt moving

Select BL.O. P/T Moving, press ENTER button to confirm, present mode will blink on the display, use UP and DOWN button to select No (normal while pan/tilt moving) or Yes (blackout while pan/tilt moving), press ENTER button to store. Press MENU button back to the last menu or let the unit idle one minute to exit menu mode.

BRITEQ® 12 BTX-700BEAM

Page 15

BL.O. Color Change—Blackout while change color

Select BL.O. Color Change, press ENTER button to confirm, present mode will blink on the display, use UP and DOWN button to select No (normal while changing color) or Yes (blackout while change color), Press MENU button back to the last menu or let the unit idle one minute to exit menu mode.

BL.O. Gobo Change—Blackout while change gobo

Select BL.O. Gobo Change, press ENTER button to confirm, present mode will blink on the display, use UP and DOWN button to select No (normal while changing gobo) or Yes (blackout while changing gobo), press ENTER button to store. Press MENU button back to the last menu or let the unit idle one minute to exit menu mode.

Lamp Setting

Attention: The lamp will not be on unit detected temperature is lower than 45°C.

Enter menu mode, select Fixture Setting, press ENTER button to confirm, use UP and DOWN button to select On/Off, State/Power on, Off Via DMX, On if DMX on, Off if

DMX off, Cooling Mode, Ignition Delay or Low Power Delay..

On/Off—Turn on/off the lamp

Select On/Off, press ENTER button to confirm, present mode will blink on the display, use UP and DOWN button to select On (lamp on) or Off (lamp off), press ENTER button to store. Press MENU button back to the last menu or let the unit idle one minute to exit menu mode.

State/Power On—Lamp state while power on

Select State/Power On, press ENTER button to confirm, present mode will blink on the display, use UP and DOWN button to select On (Lamp on while power on) or Off (Lamp off while power on), press ENTER button to store. Press MENU button back to the last menu or let the unit idle one minute to exit menu mode.

Off Via DMX—Turn off the unit via DMX controller

Select Off Via DMX, press ENTER button to confirm, present mode will blink on the display, use UP and DOWN button to select Yes (turn off the unit via DMX controller available) or No (turn off the unit via DMX controller impracticable), press ENTER button to store. Press MENU button back to the last menu or let the unit idle one minute to exit menu mode.

(When you operate the unit via DMX controller, set the value of channel “special function” to “lamp off”, waiting for 5 seconds, then the lamp will be off if you choose “yes” mode).

On If DMX On—Lamp turns on when DMX signal is detected

Select On If DMX On, press ENTER button to confirm, present mode will blink on the display, use UP and DOWN button to select Yes (Lamp turns on when DMX signal is detected) or No (keep the present state), press ENTER button to store. Press MENU button back to the last menu or let the unit idle one minute to exit menu mode.(If the lamp is off via DMX signal, you can reconnect the DMX controller to make the lamp on).

BRITEQ® 13 BTX-700BEAM

Page 16

Off If DMX Off—l Lamp turns off when DMX signal is cut off

Select Off If DMX Off, press ENTER button to confirm, present mode will blink on the display, use UP and DOWN button to select Yes (Lamp turns off when DMX signal is cut off), press ENTER button to store. Press MENU button back to the last menu or let the unit idle one minute to exit menu mode.

Cooling Mode—Lamp turns off when DMX signal is cut off

Select Cooling Mode, press ENTER button to confirm, present mode will blink on the display, use UP and DOWN button to select Auto (fans speed adjust automatically) or High (fans run in high speed), press ENTER button to store. Press MENU button back to the last menu or let the unit idle one minute to exit menu mode.

Ignition Delay—Delay time between power on and lamp on

Select Ignition Delay, press ENTER button to confirm, present mode will blink on the display, use UP and DOWN button to adjust the delay time from 0S to 255S, press ENTER button to store. Press MENU button back to the last menu or let the unit idle one minute to exit menu mode.

Low Power Delay—Delay time between reduce lamp power and shutter off the unit

Select Low Power Delay, press ENTER button to confirm, present mode will blink on the display, use UP and DOWN button to adjust the delay time from 0S to 255S, press ENTER button to store. Press MENU button back to the last menu or let the unit idle one minute to exit menu mode.

(If you set the low power delay time to 3S, the lamp will run in half power 3 seconds after the unit shutter off)

Display Setting

Enter menu mode, select Display Setting, press ENTER button to confirm, use UP and DOWN button to select Display Inverse, Backlight Auto Off, Backlight Intensity or Temperature unit.

Display Inverse Select Display Inverse, press ENTER button to confirm, present mode will blink on the display, use UP and DOWN button to select No (normal display) or Yes (inverse display), press ENTER button to store. Press MENU button back to the last menu or let the unit idle one minute to exit menu mode.

Backlight Auto Off Select Backlight Auto Off, press ENTER button to confirm, present mode will blink on the display, use UP and DOWN button to select No (display always on) or Yes (display goes off one minute after exiting menu mode), press ENTER button to store. Press MENU button back to the last menu or let the unit idle one minute to exit menu mode.

Backlight Intensity Select Backlight Intensity, press ENTER button to confirm, present mode will blink on the display, use UP and DOWN button to adjust backlight intensity from 1 (dark) to 10 (bright), press ENTER button to store. Press MENU button back to the last menu or let the unit idle one minute to exit menu mode.

BRITEQ® 14 BTX-700BEAM

Page 17

Temperature Unit Select Temperature Unit, press ENTER button to confirm, present mode will blink on

the display, use UP and DOWN button to select ℃ or ℉, press ENTER button to store. Press MENU button back to the last menu or let the unit idle one minute to exit menu

mode.

Fixture Test

Enter menu mode, select Fixture Test, press ENTER button to confirm, use UP and DOWN button to select Auto Test or Manual Test

Auto Test Select Auto Test, press ENTER button to confirm, the unit will run built-in programs to automatically test pan, tilt, color, CMY, gobo, gobo rotation, shutter, dimmer, prism, prism rotation, frost, zoom, iris, focus, flatb and lamp on/off. Press MENU button back to the last menu or exit menu mode after auto test.

Manual Test Select Manual Test, press ENTER button to confirm, the present channel will show on the display, use Up and DOWN button to select channel, press ENTER button to confirm, then use UP and DOWN button to adjust the value, press ENTER button to store, the fixture will run as the channel value indicates. Press MENU button back to the last menu or exit menu mode idling one minute.

(All channels value will become 0 after exiting Manual Test menu)

Fixture Information

Enter menu mode, select Fixture Information, press ENTER button to confirm, use UP and DOWN button to select Fixture Use Time, Lamp On Time or Firmware

Version.

Fixture Use Time

Select Fixture Use Time, press ENTER button to confirm, fixture use time will show on the display, press MENU button back to exit.

Lamp On Time Select Lamp On Time, press ENTER button to confirm, lamp on time will show on the display, press ENTER button to confirm, use UP and DOWN button to select Exit or Reset Time, press ENTER button to confirm. Press MENU button back to the last menu or exit menu mode let the unit idle one minute.

Firmware Version Select Firmware Version, press ENTER button to confirm, firmware version will show on the display, press MENU button back to exit.

Reset Functions

Enter menu mode, select Reset Function, press ENTER button to confirm, use UP and DOWN button to select Pan/Tilt, Color/CMY, Gobo, Shutter/Dimmer, Focus/Zoom/Prism/Frost , Iris/Flatb or All.

BRITEQ® 15 BTX-700BEAM

Page 18

Pan/Tilt—Reset Pan/Tilt

Select Pan/Tilt, press ENTER button to confirm, use UP and DOWN button to select Yes (the unit will run built-in program to reset pan and tilt to their home positions) or No,

press ENTER button to store. Press MENU button to exit.

Shutter/Dimmer—Reset Shutter/Dimmer Select Shutter/Dimmer, press ENTER button to confirm, use UP and DOWN button to

select Yes (the unit will run built-in program to reset shutter and dimmer to their home positions) or No, press ENTER button to store. Press MENU button to exit.

Color/CMY—Reset Color/CMY

Select Color/CMY, press ENTER button to confirm, use UP and DOWN button to select Yes (the unit will run built-in program to reset color and CMY to their home positions) or No, press ENTER button to store. Press MENU button to exit.

GOBO—Reset GOBO

Select GOBO, press ENTER button to confirm, use UP and DOWN button to select Yes (the unit will run built-in program to reset GOBO wheel to their home positions) or No, press ENTER button to store. Press MENU button to exit.

Prism/Frost—Reset Prism/Frost

Select Prism/Frost, press ENTER button to confirm, use UP and DOWN button to select Yes (the unit will run built-in program to reset prism and frost to their home positions) or No, press ENTER button to store. Press MENU button to exit.

All—Reset All

Select All, press ENTER button to confirm, use UP and DOWN button to select Yes (the unit will run built-in program to reset all motors to their home positions) or No, press ENTER button to store. Press MENU button to exit.

Special Functions

Enter menu mode, select Special Functions, press ENTER button to confirm, use UP and DOWN button to select Fixture Maintenance or Factory Setting.

Fixture Maintenance Select Fixture Maintenance, press ENTER button to confirm, use UP and DOWN button to select Interval or Remain Time.

Interval

Select Interval, press ENTER button to confirm, the interval time will show on the display. Press MENU button to exit.

Remain Time

Select Remain Time, press ENTER button to confirm, the remaining time will show on the display, press ENTER button to confirm, use UP and DOWN button to select Exit or Reset time, press MENU button to exit.

BRITEQ® 16 BTX-700BEAM

Page 19

Factory Setting Select Factory Setting, press ENTER button to confirm, the fixture will reset to factory settings and exit menu mode.

6.3. Home Position Adjustment

Press MENU button into menu mode, then press ENTER button for about 3 seconds into offset mode to adjust the home position. Select the function by ENTER button. Use UP and DOWN button to choose the submenu, press the ENTER button to store and automatically return to the last menu. Press MENU button to exit.

Pan—pan home position adjust Enter offset mode, Select Pan, press ENTER button to confirm, the present position will

blink on the display, use UP and DOWN button to offset the value from -128 to 127, press ENTER button to store. Press MENU button to exit.

Tilt—Tilt home position adjust Enter offset mode, Select Tilt, press ENTER button to confirm, the present position will

blink on the display, use UP and DOWN button to offset the value from -128 to 127, press ENTER button to store. Press MENU button to exit.

Shutter—Shutter home position adjust Enter offset mode, Select Shutter, press ENTER button to confirm, the present position will

blink on the display, use UP and DOWN button to offset the value from 0 to 255, press ENTER button to store. Press MENU button to exit.

Dimmer—Dimmer home position adjust Enter offset mode, Select Dimmer, press ENTER button to confirm, the present position

will blink on the display, use UP and DOWN button to offset the value from 0 to 255, press ENTER button to store. Press MENU button to exit.

BRITEQ® 17 BTX-700BEAM

Page 20

Color—Color home position adjust Enter offset mode, Select Color, press ENTER button to confirm, the present position will

blink on the display, use UP and DOWN button to offset the value from -128 to 127, press ENTER button to store. Press MENU button to exit.

Cyan—Cyan home position adjust Enter offset mode, Select Cyan, press ENTER button to confirm, the present position will

blink on the display, use UP and DOWN button to offset the value from 0 to 255, press ENTER button to store. Press MENU button to exit.

Magenta—Magenta home position adjust Enter offset mode, Select Magenta, press ENTER button to confirm, the present position

will blink on the display, use UP and DOWN button to offset the value from 0 to 255, press ENTER button to store. Press MENU button to exit.

Yellow—Yellow home position adjust Enter offset mode, Select Yellow, press ENTER button to confirm, the present position will

blink on the display, use UP and DOWN button to offset the value from 0 to 255, press ENTER button to store. Press MENU button to exit.

Gobo—Gobo home position adjust Enter offset mode, Select Gobo, press ENTER button to confirm, the present position will

blink on the display, use UP and DOWN button to offset the value from -128 to 127, press ENTER button to store. Press MENU button to exit.

R-Gobo—Gobo rotation home position adjust Enter offset mode, Select R-Gobo, press ENTER button to confirm, the present position will

blink on the display, use UP and DOWN button to offset the value from -128 to 127, press ENTER button to store. Press MENU button to exit.

Prism—Prism home position adjust Enter offset mode, Select Prism, press ENTER button to confirm, the present position will

blink on the display, use UP and DOWN button to offset the value from 0 to 255, press ENTER button to store. Press MENU button to exit.

R-Prism—Prism rotation home position adjust Enter offset mode, Select R-Prism, press ENTER button to confirm, the present position

will blink on the display, use UP and DOWN button to offset the value from -128 to 127, press ENTER button to store. Press MENU button to exit.

Frost—Frost home position adjust Enter offset mode, Select Frost, press ENTER button to confirm, the present position will

blink on the display, use UP and DOWN button to offset the value from 0 to 255, press ENTER button to store. Press MENU button to exit.

6.4. Error Information

Lamp Startup Fail

It appears when there is no lamp or some wires are damaged.

Temperature Sense Error

It appears when temperature check board is damaged.

BRITEQ® 18 BTX-700BEAM

Page 21

Lamp Too Hot Power Off

It appears when temperature is detected higher than 110℃. Check if the unit is properly ventilated, or fans or temperature check board may is damaged.

Lamp Too Hot Low Power

It appears when detected temperature is over 105℃. the unit will run on a low power level.

Maintenance Fixture

It appears when the maintenance remaining time becomes 0S, please enter menu mode and reset the time.

Lamp On Over 700 Hour

It appears when the lamp has been on over 700 hours, please turn off the lamp.

Memory Initial Fail

It appears when the memory IC is damaged.

CPU-B Error, CPU-C Error, CPU-D Error

They appear when board P.C or some wires are damaged.

Pan Reset Error, Pan Encode Error, Tilt Reset Error, Tilt Encode Error, Shutter Reset Fail, Dimmer Reset Fail, Color Reset Fail, Cyan Reset Fail, Magenta Reset Fail, Yellow Reset Fail, Gobo Reset Fail, R-Gobo Reset Fail, Effect Reset Fail, R-Effect Reset Fail, and Frost Reset Fail

They may appear when turn on or reset the unit, for some parts such as board P.C are damaged. Please contact the qualified maintenance.

7. Control By Universal DMX Controller

7.1 Connection

BRITEQ® 19 BTX-700BEAM

Page 22

Channel mode

Unit 1

Address

Unit 2

Address

Unit 3

Address

Unit 4

Address

18 channels

25 channels

ATTENTION

Termination reduces signal errors and to avoid signal transmission

problems and interference. It is always advisable to connect a DMX terminal

(Resistance 120 ohm 1/4W between pin2 (DMX-) and pin3 (DMX+) of the last

1. At last unit, the DMX cable has to be terminated with a terminator. Solder a 120-ohm 1/4W resistor between pin 2(DMX-) and pin 3(DMX+) into a 3-pin XLR-plug and plug it in the DMX-output of the last unit.

2. Connect the unit together in a “daisy chain” by XLR plug cable from the output of the unit to the input of the next unit. The cable cannot be branched or split to a “Y” cable. DMX 512 is a very high-speed signal. Inadequate or damaged cables, soldered joints or corroded connectors can easily distort the signal and shut down the system.

3. The DMX output and input connectors are pass-through to maintain the DMX circuit, when one of the units’ power is disconnected.

4. Each lighting unit needs to have a DMX address to receive the data by the controller. The address number is between 0-511 (usually 0 & 1 are equal to 1).

5. The end of the DMX 512 system should be terminated to reduce signal errors.

6. 3 pin XLR connectors are more popular than 5 pins XLR. 3 pin XLR: Pin 1: GND, Pin 2: Negative signal (-), Pin 3: Positive signal (+) 5 pin XLR: Pin 1: GND, Pin 2: Negative signal (-), Pin 3: Positive signal (+), Pin4, Pin5 not used.

7.2 Channel Mode Setting

Enter menu mode, select DMX Functions, press ENTER button to confirm, use UP and DOWN button to select DMX Channel Mode, press ENTER button to confirm, present channel mode will blink on the display, use UP and DOWN button to select Mode1 (18 channels mode) or Mode 2 (18 channels mode) or Mode 3 (25 channels mode), press ENTER button to store. Press MENU button back to the last menu or let the unit idle one minute to exit menu mode.

7.3 Address Setting

If you use a universal DMX controller to control the units, you have to set DMX address from 1 to 512 so that the units can receive DMX signal. Press MENU button to enter menu mode, select DMX Functions, press ENTER button to confirm, use UP and DOWN button to select DMX Address, press ENTER button to confirm, the present address will blink on the display, use UP and DOWN button to adjust the address from 0 to 512, press ENTER button to store. Press MENU button back to the last menu or let the unit idle one minute to exit menu mode. Please refer to the following diagram to address your DMX512 channel for the first 4 units.

BRITEQ® 20 BTX-700BEAM

Page 23

7.4 DMX 512 Configuration

Please refer to below configurations to control the fixtures

Attention:

1. The unit will maintain the last condition until reset if you cut-off the DMX signal)

2. For the channel Function, keep the value for about 5 seconds, then the corresponding

function will take into effect.

18 Channels mode 1:

BRITEQ® 21 BTX-700BEAM

Page 24

18 Channels mode 2:

BRITEQ® 22 BTX-700BEAM

Page 25

BRITEQ® 23 BTX-700BEAM

Page 26

25 Channels mode:

BRITEQ® 24 BTX-700BEAM

Page 27

BRITEQ® 25 BTX-700BEAM

Page 28

8. Update Software

Download update file (if available) from www.briteq-lighting.com , follow the user manual of our firmware updater (not included, order code: 4319) to update the fixture.

9. Troubleshooting

Following are a few common problems that may occur during operation. Here are some suggestions for easy troubleshooting: A. The unit does not work, no light and the fan does not work

1. Check the connect power and main fuse.

2. Measure the mains voltage on the main connector.

3. Check the power on LED to see if it can be light up or not.

B. Not responding to DMX controller

1. DMX LED should be on. If not, check DMX connectors, cables to see if they are linked

properly.

2. If the DMX LED is on and no response to the channel, check the address settings and

DMX polarity.

3. If you have intermittent DMX signal problems, check the pins on connectors or on PCB

of the unit or the previous one.

4. Try to use another DMX controller.

5. Check to see if the DMX cables run near or run alongside high voltage cables that may

cause damage or interference to DMX interface circuit.

C. One of the channels is not working well

1. The stepper motor might be damaged or the cable connected to the PCB is broken.

2. The motor’s drive IC on the PCB might be out of condition.

D. The lamp is cutting out intermittently

1. The lamp is not working well. Check the mains voltage either too high or too low.

2. Internal temperature may be too high. Check if replacement of fan is needed on the

head.

E. If The pan belt is broken

1. Turn off the mains power.

2. Loosen the screws (A)，open the cover (B).

3. Loosen the screws (C).

4. Unplug all the connect wires over the belt.

5. Change a new belt (D), put the belt around the axis gear and

motor gear.

6. Plug all the connect wires back upon the belt.

7. Tighten all the screws.

F. If The tilt belt is broken

1. Turn off the mains power.

2. Loosen all the screws (A) and open the right arm

cover (B).

3. Loosen the screws (C) that fix the bridge.

4. Change a new belt (D). Please adjust the tension of

the belt properly. Note: do not fix the belt too tight as it is can easily rupture.

5. Reverse the procedures from step 3 to 2.

BRITEQ® 26 BTX-700BEAM

Page 29

10. Maintenance and Cleaning

Maintenance:

Ignitor Ballast Filter

A. As the pictures shown above, please replace the cable or cable joints immediately once

they’ve turned yellow.

B. Do maintain the fixtures every two months and make sure that all the screws and

terminals have been locked firmly to make sure the normal performance of the fixtures. Negligence of maintenance would cause malfunction of the fixture.

Cleaning:

The cleaning of internal and external optical lenses and/or mirrors must be carried out periodically to optimize light output. Cleaning frequency depends on the environment in which the fixture operates: damp, smoky or particularly dirty surrounding can cause greater accumulation of dirt on the unit’s optics.

 Clean with soft cloth and use normal glass to clean fluid.  Always dry the parts carefully.  Clean the external optics at least every 20 days. Clean the internal optics at least every

30/60 days.

Fresnel Lens:

Clean the lens with neutral soap and water, and then dry it with soft cloth. Be aware that alcohol or other detergent could cause damage to lens. Please note the lens would be burnt yellow or cracked after three-month use of average 8 hours per day, which can reduce the output in some degree. The lens is consumable with a warranty of three months only. Please change with genuinely new lens when necessary.

BRITEQ® 27 BTX-700BEAM

Page 30

Page 31

Page 32

WWW.BRITEQ-LIGHTING.COM

‘t Hofveld 2C ~ B1702 Groot-Bijgaarden ~ Belgium

Reproduction or publication of the content in any manner, without express permission of the publisher, is prohibited.