Page 1
Other languages can be downloaded from:
Version: 1.0
ENGLISH
Operation Manual
WWW.BRITEQ-LIGHTING.COM
Page 2
Page 3
ENGLISH OPERATION MANUAL
BRITEQ
®
1/12 BT-THEATRE 261FC
OPERATION MANUAL
Thank you for buying this Briteq® product. To take full advantage of all possibilities and for your own safety,
please read these operating instructions very carefully before you start using this unit.
FEATURES
• A powerful “6-IN-1” FULL COLOR LED theater Fresnel with manual 15° ~ 50° zoom.
• No more need for separate white and color projectors, BT-THEATRE 261FC does it all:
• Perfect WHITE with high CRI > 93Ra and several CCT presets
• Rich COLOR selection with color presets following the LEE® numbering!
• Thanks to the Color Calibration System, there are no more the color differences between different batches!
• Different CCT presets for white: 1800K, 3000K, 4000K, …, 8000K
• Very realistic redshift emulation during projector dimming.
• The 94 most used color presets (LEE® numbering) can be selected!
• The 200watt 6-color RGBALC-LED (Red, Green, Blue, Amber, Lime, Cyan) assures a very wide color gamut.
• Very silent operation: heat-pipe technology with low noise cooling fan and different presets (live, studio, …)
• DMX-controlled: 10 different channel modes (1 to 21 channels) for maximum flexibility.
• Prepared for wireless DMX: just plug-in an optional WTR-DMX DONGLE ! (Briteq® code: 4645)
• RDM-functionality for easy remote setup: DMX addressing, channel mode, …
• Flicker free TV-recordings thanks to the adjustable high LED-refresh rate!
• Four dimmer settings with different behavior & speed.
• Standalone mode: manual control for dimming, color/CCT presets, green/magenta shift & zoom.
• OLED-display to navigate easily through the setup menu!
• In case of DMX failure, you can choose between manual, blackout and freeze mode.
• Lock function to avoid unwanted altering of the settings.
• Eight-leaf barndoor included.
• Rugged extruded aluminum housing.
• 3 & 5pin DMX in/outputs + PowerCON® compatible in/outputs for easy daisy chaining.
BEFORE USE
• Before you start using this unit, please check if there’s no transportation damage. Should there be any, do
not use the device and consult your dealer first.
• Important: This device left our factory in perfect condition and well packaged. It is absolutely necessary for
the user to strictly follow the safety instructions and warnings in this user manual. Any damage caused by
mishandling is not subject to warranty. The dealer will not accept responsibility for any resulting defects or
problems caused by disregarding this user manual.
• Keep this booklet in a safe place for future consultation. If you sell the fixture, be sure to add this user manual.
Check the contents:
Check that the carton contains the following items:
• English operating instructions, other languages can be downloaded from our website.
• BT-THEATRE 261FC
• Color frame
• Eight-leaf barndoor
• PowerCON® compatible mains cable
Page 4
ENGLISH OPERATION MANUAL
BRITEQ
®
2/12 BT-THEATRE 261FC
SAFETY INSTRUCTIONS:
• To protect the environment, please try to recycle the packing material as much as possible.
• To prevent fire or shock hazard, do not expose this appliance to rain or moisture.
• To avoid condensation to be formed inside, allow the unit to adapt to the surrounding temperatures when
bringing it into a warm room after transport. Condense sometimes prevents the unit from working at full
performance or may even cause damages.
• This unit is for indoor use only.
• Don’t place metal objects or spill liquid inside the unit. Electric shock or malfunction may result. If a foreign
object enters the unit, immediately disconnect the mains power.
• Locate the fixture in a well-ventilated spot, away from any flammable materials and/or liquids. The fixture
must be fixed at least 50cm from surrounding walls.
• Don’t cover any ventilation openings as this may result in overheating.
• Prevent use in dusty environments and clean the unit regularly.
• Keep the unit away from children.
• Inexperienced persons should not operate this device.
• Maximum safe ambient temperature is 40°C. Don’t use this unit at higher ambient temperatures.
• Make sure the area below the installation place is free from unwanted persons during rigging, de-rigging and
servicing.
• Allow the device about 10 minutes to cool down before to start servicing.
• Always unplug the unit when it is not used for a longer time or before to start servicing.
• The electrical installation should be carried out by qualified personal only, according to the regulations for
electrical and mechanical safety in your country.
• Check that the available voltage is not higher than the one stated on the unit.
• The power cord should always be in perfect condition. Switch the unit immediately off when the power cord
is squashed or damaged. It must be replaced by the manufacturer, its service agent or similarly qualified
persons in order to avoid a hazard.
• Never let the power-cord come into contact with other cables!
• This fixture must be earthed in order to comply with safety regulations.
• Don’t connect the unit to any dimmer pack.
• Always use an appropriate and certified safety cable when installing the unit.
• In order to prevent electric shock, do not open the cover. Apart from the mains fuse there are no user
serviceable parts inside.
• Never repair a fuse or bypass the fuse holder. Always replace a damaged fuse with a fuse of the same type
and electrical specifications!
• In the event of serious operating problems, stop using the fixture and contact your dealer immediately.
• The housing and the lenses must be replaced if they are visibly damaged.
• Please use the original packing when the device is to be transported.
• Due to safety reasons it is prohibited to make unauthorized modifications to the unit.
Important: Never look directly into the light source! Don’t use the effect in the presence of persons suffering
from epilepsy.
CAUTION: To reduce the risk of electric shock, do not remove
the top cover. No user-serviceable parts inside. Refer servicing
to qualified service personnel only.
The lightning flash with arrowhead symbol within the equilateral triangle is intended to alert the
use or the presence of un-insulated “dangerous voltage” within the product’s enclosure that may
be of sufficient magnitude to constitute a risk of electric shock.
The exclamation point within the equilateral triangle is intended to alert the user to the presence
of important operation and maintenance (servicing) instructions in the literature accompanying
this appliance.
This symbol means: indoor use only
This symbol means: Read instructions
This symbol determines: the minimum distance from lighted objects. The minimum distance
between light-output and the illuminated surface must be more than 1 meters
CAUTION: Do not stare at operating lamp.
May be harmful to the eyes.
Page 5
ENGLISH OPERATION MANUAL
BRITEQ
®
3/12 BT-THEATRE 261FC
DESCRIPTION:
1. MAINS INPUT: equipped with PowerCON® compatible connectors. Connect the supplied mains cable or
any PowerCON® compatible extension cable here.
2. MAINS OUTPUT: used to daisy chain the power to several other projectors. Always pay attention to the
maximum load while adding projectors! Special Multi cables (PowerCON® + DMX XLR-cables are optionally
available: see our website!)
3. FOCUS KNOB: used to adjust the beam angle manually.
4. MAINS FUSE: protects the unit in case of electrical problems, always use the prescribed fuse!
5. DMX IN/OUT: both 3pin and 5pin in/outputs are available to daisy chain the projector with other units that
will be controlled by a DMX-controller.
6. M-DMX INPUT: Please note that this USB-connector is NOT used for updates or to connect the unit to a
PC! Instead this USB-connector makes it very easy to add wireless DMX to the unit! Just add the (optional)
WTR-DMX DONGLE from BRITEQ® and you will get wireless DMX! Moreover, you will be able to connect
other DMX-controlled equipment to the DMX-output so you can share the wireless DMX function with all
connected units! No extra settings to be made in the setup menu, just follow the procedure in the user
manual supplied with the WTR-DMX DONGLE from BRITEQ®. The separate WTR-DMX DONGLE is
available from WWW.BRITEQ-LIGHTING.COM (order code: 4645)
7. DISPLAY: shows the various menus and the selected functions.
8. MENU-button: used to enter and exit the setup menu or to jump to a higher level in the setup menu.
9. ENTER-button: used to select a menu option or confirm a setting.
10. ▲-button: used to go to the previous menu option or to increase a parameter value.
11. ▼-button: used to go to the next menu option or to decrease a parameter value.
12. DIMMER KNOB: turn the encoder to change the light output manually. Press the encoder for 2 seconds
if you want to save the new light output value for future use.
13. CONTROL KNOB: this knob has several functions.
• CHANGE CCT: press the encoder until the display shows [CCT]. Turn the encoder to select the desired
CCT-preset. Press the encoder for 2 seconds if you want to save the new CCT for future use. Press the
encoder again shortly to select the next function.
• CHANGE GREEN/MAGENTA CORRECTION: press the encoder until the display shows [TINT]. Turn
the encoder to select the desired color correction. Press the encoder for 2 seconds if you want to save
the new correction for future use. Press the encoder again shortly to select the next function.
• COLOR PRESETS: press the encoder until the display shows [COLOR PRESET]. Turn the encoder to
select the desired color preset. Press the encoder for 2 seconds if you want to save the new color preset
for future use. Press the encoder again shortly to select the next function.
Page 6
ENGLISH OPERATION MANUAL
BRITEQ
®
4/12 BT-THEATRE 261FC
14. HANDLE: used for aligning the spotlight. Can also be used to attach the safety cable during installation,
see paragraph “overhead rigging”.
15. HANGING BRACKET: with a knob on both sides to fasten the unit in the desired position. You can use the
hole in the center of the bracket to fix a hook or truss clamp.
16. LOCKING CLIP: The clip is used to keep the barndoor and color frame in place. Push the clip aside to
open it.
17. BARN DOOR: they facilitate shaping of the beam of light from the fixture, and prevent the distinctive scatter
of light created by the Fresnel lens from spilling into areas where it is not wanted, such as the eyes of
audience members. Just rotate the barndoor in the desired position.
SETUP MENU / HOW TO SETUP
With the setup menu you can fully configure the projector. All settings are preserved when the unit is
disconnected from the mains.
■ [MENU] button: press to enter / leave the setup menu.
► [ENTER] button: press to select / confirm or store the current menu option or value.
▲/▼ [UP/DOWN] button: press to navigate the setup menu or change a value.
DMX-Address
001 - XXX
CHAN. Mode
DIM (1CH)
CCT (4CH)
EASY (6CH)
HSI (6CH)
HSIC FULL (12CH)
CMY (12CH)
FULL 8bit (14CH)
FULL 16bit(21CH)
RAW 8bit (9CH)
RAW 16bit (16CH)
FIXTURE Set
NO DMX Mode
Freeze
Blackout
Blackout delayed
Manual
DIM Curve
Linear
Square
Inv. Square
S-Curve
DIM Behavior
HALOGEN / LED
Red Shift
ON /OFF
LED PWM-freq
1200Hz → 25kHz
1CH CCT preset
1800K → 8000K
Color Cal
ON /OFF
FAN Set
Low Auto High
DISPLAY Set
AUTO LOCK
ON /OFF
noDMX blink
ON /OFF
Temp °C/F
Celcius/Fahrenheit
DEFAULTS
Factory Settings
LOAD ?
USER Settings
LOAD / SAVE ?
INFORMATION
Total LED Hours
xxxx Hrs
Last JOB hours
xxxx Hrs
LED Temp.
xxx °C / F
ERROR info
xxxxxxxx
Model Name
BT-THEATRE 261FC
Firmware V.
V x.xx
RDM UID
0x21220043xxxx
Page 7
ENGLISH OPERATION MANUAL
BRITEQ
®
5/12 BT-THEATRE 261FC
OVERHEAD RIGGING
Important: The installation must be carried out by qualified service personal only. Improper installation
can result in serious injuries and/or damage to property. Overhead rigging requires extensive
experience! Working load limits should be respected, certified installation materials should be used,
the installed device should be inspected regularly for safety.
• Make sure the area below the installation place is free from unwanted persons
during rigging, de-rigging and servicing.
• Locate the fixture in a well-ventilated spot, far away from any flammable materials
and/or liquids. The fixture must be fixed at least 50cm from surrounding walls.
• The device should be installed out of reach of people and outside areas where
persons may walk by or be seated.
• Before rigging make sure that the installation area can hold a minimum point
load of 10times the device’s weight.
• Always use a certified safety cable that can hold 12times the weight of the
device when installing the unit. This secondary safety attachment should be
installed in a way that no part of the installation can drop more than 20cm if
the main attachment fails.
• The device should be well fixed; a free-swinging mounting is dangerous and
may not be considered!
• Don’t cover any ventilation openings as this may result in overheating.
• The operator has to make sure that the safety-relating and machine-
technical installations are approved by an expert before using them for the
first time. The installations should be inspected every year by a skilled
person to be sure that safety is still optimal.
ELECTRICAL INSTALLATION
Important: The electrical installation should be carried out by qualified personal only,
according to the regulations for electrical and mechanical safety in your country.
Electrical installation for two or more units in DMX-mode:
• The DMX-protocol is a widely used high speed signal to control intelligent light equipment. You need to
“daisy chain” your DMX controller and all the connected units.
• Pin layout XLR-3pin: Pin1 = GND ~ Pin2 = Negative signal (-) ~ Pin3 = Positive signal (+)
• To prevent strange behavior of the light effects, due to interferences, you must use
a 90Ω to 120Ω terminator at the end of the chain. Never use Y-splitter cables, this
simply won’t work!
• Make sure that all units are connected to the mains.
• Each unit in the chain needs to have its proper starting address so it knows which
commands from the controller it has to decode.
Page 8
ENGLISH OPERATION MANUAL
BRITEQ
®
6/12 BT-THEATRE 261FC
Electrical installation for two or more units in WIRELESS DMX:
Same procedure as for a standard DMX-setup but 2 possibilities:
• Pure W-DMX: all projectors are equipped with an optional WTR-DMX DONGLE ! (Briteq code: 4645).
The DMX-controller send a WIRELESS DMX-signal to all units.
• Mixed W-DMX: the first projector is equipped with an optional WTR-DMX DONGLE ! (Briteq code:
4645). The wireless DMX-signal sent to the first projector is also available on its DMX-output. All other
DMX-equipment can be connected to the first projector using a standard DMX-cable.
RDM FUNCTIONS / REMOTE SETUP
RDM means “Remote Device Management”. This projector works with a brief set of RDM-functions which
means that it can setup a bi-directional communication with an RDM-compatible DMX-controller. Some of
these functions are briefly explained below, others will be added in the future.
• The DMX-controller sends out a “discovery command”, all RDM devices respond and send their unique
device ID.
• The DMX-controller asks each RDM device for some basic data so it knows which devices are connected.
The projector will respond:
• Device name: BT-THEATRE 261FC
• Manufacturer: Briteq®
• Category: LED Dimmer
• Firmware: x.x.x.x (firmware version of the projector)
• DMX address: xxx (current DMX start address of the projector)
• DMX footprint: xx (number of DMX-channels used by the projector)
• Personality: xx (current personality [or DMX-working mode] used by the projectors)
• The DMX-controller can send certain commands to each RDM device which allow remote setup of the units.
Thanks to this the projector can be setup remotely.
The following functions can be managed remotely:
No more need to take a ladder and set all units one by one!
• DMX START ADDRESS: The start address can be set remotely from 001 to xxx.
• PERSONALITY: The DMX working mode (DMX-chart) can be set remotely.
These 2 functions make it possible to prepare a complete DMX-patch of all projectors on the DMX-controller
and send these data to all projectors at once. More functions will be added later.
Page 9
ENGLISH OPERATION MANUAL
BRITEQ
®
7/12 BT-THEATRE 261FC
DMX CHARTS
Personalities: Dim (1ch), CCT (4ch), Easy (6ch), HSI (6ch), HSIC Full (12ch), CMY (12ch), Full 8bit (14ch),
Full 16bit (21ch), RAW 8bit (9ch), RAW 16bit (16ch)
SIMPLE CHART
DIM
CCT
EASY
HSI
HSIC
FULL
CMY
FULL
8bit
FULL
16bit
RAW
8bit
RAW
16bit
VALUE
FUNCTION
1CH
4CH
6CH
6CH
12CH
12CH
14CH
21CH
9CH
16CH
1 1 1 1 1 1 1 1 1
1
000-255
MASTER DIMMER
2 2 2
2
000-255
MASTER DIMMER FINE
2 2 2 3 3 2 3 2
3
000-255
STROBE
3 3 4 4 3 4
000-255
CCT (Color temperature)
4 5 5 4 5
000-255
TINT: GREEN / MAGENTA
correction
4 6 6 5 6
000-255
X-FADE: CCT ↔ COLOR
5 7 7 6 7
000-255
COLOR FILTER PRESETS (White
point = 3200K)
6 8 8 7 8
000-255
COLOR FILTER FADE-OVER TIME
3 9
000-255
HUE
4 10
000-255
HUE FINE
5 11
000-255
SATURATION
8 9 3
4
000-255
RED
10 5
000-255
RED FINE
9
11 4 6
000-255
GREEN
12 7
000-255
GREEN FINE
10
13 5 8
000-255
BLUE
14 9
000-255
BLUE FINE
11
15 6 10
000-255
AMBER
16 11
000-255
AMBER FINE
12
17 7 12
000-255
LIME
18 13
000-255
LIME FINE
9 13
19 8 14
000-255
CYAN
20 15
000-255
CYAN FINE
10
000-255
MAGENTA
11
000-255
YELLOW
6 12
12
14
21 9 16
000-255
CONTROL (active after 3s)
FULL CHART
DIM
CCT
EASY
HSI
HSIC
FULL
CMY
FULL
8bit
FULL
16bit
RAW
8bit
RAW
16bit
VALUE
FUNCTION
1 1 1 1 1 1 1 1 1
1
000-255
MASTER DIMMER
2 2 2
2
000-255
MASTER DIMMER FINE
2 2 2 3 3 2 3 2
3
STROBE
000-005
Open (no strobe)
006-125
Normal strobe (slow → fast)
126-135
Open (no strobe)
136-255
Random strobe (slow → fast)
3 3 4 4 3 4
CCT (Color temperature)
000-009
NO FUNCTION
010-255
1800K ↔ 8000K
4 5 5 4 5
TINT: GREEN / MAGENTA correction
000-016
NEUTRAL / no effect
017-116
MAGENTA 99% ↔ 1%
117-139
NEUTRAL / no effect
140-239
GREEN 1% ↔ 99%
240-255
GREEN 100%
4 6 6 5 6
000-255
X-FADE: CCT ↔ COLOR
5 7 7 6 7
COLOR FILTER PRESETS (White point = 3200K)
000-005
NO FUNCTION - No Filters, color channels used
006-193
Color filter presets SEE NEXT TABLE for details!
194-195
USER Color 1
196-197
USER Color 2
198-199
USER Color 3
200-201
USER Color 4
202-204
USER Color 5
205-255
COLOR SCROLL: slow ↔ fast
6 8 8 7 8
000-255
COLOR FILTER FADE-OVER TIME
3 9
000-255
HUE
Page 10
ENGLISH OPERATION MANUAL
BRITEQ
®
8/12 BT-THEATRE 261FC
4 10
000-255
HUE FINE
5 11
000-255
SATURATION
8 9 3
4
000-255
RED
10 5
000-255
RED FINE
9
11 4 6
000-255
GREEN
12 7
000-255
GREEN FINE
10
13 5 8
000-255
BLUE
14 9
000-255
BLUE FINE
11
15 6 10
000-255
AMBER
16 11
000-255
AMBER FINE
12
17 7 12
000-255
LIME
18 13
000-255
LIME FINE
9 13
19 8 14
000-255
CYAN
20 15
000-255
CYAN FINE
10
000-255
MAGENTA
11
000-255
YELLOW
6 12
12
14
21 9 16
CONTROL (active after 3 seconds)
000-005
NO FUNCTION
006-010
DIM CURVE: LINEAR
011-015
DIM CURVE: SQUARE
016-020
DIM CURVE: INVERSE SQUARE
021-025
DIM CURVE: S-CURVE
026-035
RESERVED
036-040
DIM BEHAVIOR: LED
041-045
DIM BEHAVIOR: HALOGEN
046-055
RESERVED
056-060
No DMX: Freeze MODE
061-065
No DMX: blackout delayed MODE
066-070
No DMX: blackout MODE
071-075
No DMX: Manual MODE
076-085
RESERVED
086-090
Display: BLINK ON
091-095
Display: BLINK OFF
096-160
RESERVED
106-110
FAN MODE = low / silent
111-115
FAN MODE = auto
116-120
FAN MODE = high / performance
121-130
RESERVED
131-135
LED PWM = 1200Hz
136-140
LED PWM = 2400Hz
141-145
LED PWM = 3600Hz
146-150
LED PWM = 7200Hz
151-155
LED PWM = 14400Hz
156-160
LED PWM = 20000Hz
161-165
LED PWM = 25000Hz
166-175
RESERVED
176-180
RED SHIFT OFF
181-185
RED SHIFT ON
186-195
RESERVED
196-200
LED CALIBRATION OFF
201-205
LED CALIBRATION ON
206-215
RESERVED
216-220
RECORD USER Color 1
221-225
RECORD USER Color 2
226-230
RECORD USER Color 3
231-235
RECORD USER Color 4
236-240
RECORD USER Color 5
241-255
RESERVED
COLOR PRESETS + LEE FILTER NAMES + CIE 1931 X/Y coordinates @ 3200K
Color preset
Value
Filter Preset
X
Y
Color preset 1
006-007
Filter 004 (Medium Bastard Amber)
0,488
0,391
Color preset 2
008-009
Filter 009 (Pale Amber Gold)
0,479
0,417
Color preset 3
010-011
Filter 017 (Surprise Peach)
0,544
0,395
Color preset 4
012-013
Filter 019 (Fire)
0,665
0,33
Color preset 5
014-015
Filter 021 (Gold Amber)
0,611
0,383
Color preset 6
016-017
Filter 025 (Sunset Red)
0,62
0,354
Color preset 7
018-019
Filter 026 (Bright Red)
0,701
0,299
Color preset 8
020-021
Filter 029 (Plasa Red)
0,702
0,298
Page 11
ENGLISH OPERATION MANUAL
BRITEQ
®
9/12 BT-THEATRE 261FC
Color preset 9
022-023
Filter 035 (Light Pink)
0,462
0,37
Color preset 10
024-025
Filter 036 (Medium Pink)
0,495
0,345
Color preset 11
026-027
Filter 049 (Medium Purple)
0,474
0,197
Color preset 12
028-029
Filter 052 (Light Lavender)
0,391
0,315
Color preset 13
030-031
Filter 058 (Lavender)
0,312
0,185
Color preset 14
032-033
Filter 068 (Sky Blue)
0,174
0,207
Color preset 15
034-035
Filter 071 (Tokyo Blue)
0,154
0,035
Color preset 16
036-037
Filter 075 (Evening Blue)
0,198
0,192
Color preset 17
038-039
Filter 079 (Just Blue)
0,153
0,139
Color preset 18
040-041
Filter 088 (Lime Green)
0,429
0,505
Color preset 19
042-043
Filter 089 (Moss Green)
0,311
0,58
Color preset 20
044-045
Filter 090 (Dark Yellow Green)
0,196
0,685
Color preset 21
046-047
Filter 102 (Light Amber)
0,492
0,479
Color preset 22
048-049
Filter 103 (Straw)
0,458
0,416
Color preset 23
050-051
Filter 106 (Primary Red)
0,693
0,305
Color preset 24
052-053
Filter 108 (English Rose)
0,515
0,397
Color preset 25
054-055
Filter 111 (Dark Pink)
0,522
0,324
Color preset 26
056-057
Filter 113 (Magenta)
0,662
0,29
Color preset 27
058-059
Filter 115 (Peacock Blue)
0,198
0,414
Color preset 28
060-061
Filter 116 (Med Blue-Green)
0,13
0,4
Color preset 29
062-063
Filter 117 (Steel Blue)
0,332
0,39
Color preset 30
064-065
Filter 118 (Light Blue)
0,174
0,309
Color preset 31
066-067
Filter 119 (Dark Blue)
0,137
0,109
Color preset 32
068-069
Filter 121 (LEE Green)
0,392
0,53
Color preset 33
070-071
Filter 122 (Fern Green)
0,336
0,549
Color preset 34
072-073
Filter 124 (Dark Green)
0,212
0,618
Color preset 35
074-075
Filter 126 (Mauve)
0,463
0,18
Color preset 36
076-077
Filter 127 (Smokey Pink)
0,53
0,34
Color preset 37
078-079
Filter 128 (Bright Pink)
0,565
0,256
Color preset 38
080-081
Filter 131 (Marine Blue)
0,268
0,419
Color preset 39
082-083
Filter 132 (Medium Blue)
0,148
0,195
Color preset 40
084-085
Filter 134 (Golden Amber)
0,559
0,398
Color preset 41
086-087
Filter 135 (Deep Golden Amber)
0,649
0,35
Color preset 42
088-089
Filter 136 (Pale Lavender)
0,412
0,348
Color preset 43
090-091
Filter 137 (Special Lavender)
0,348
0,3
Color preset 44
092-093
Filter 138 (Pale Green)
0,419
0,463
Color preset 45
094-095
Filter 139 (Primary Green)
0,212
0,717
Color preset 46
096-097
Filter 140 (Summer Blue)
0,277
0,367
Color preset 47
098-099
Filter 141 (Bright Blue)
0,147
0,267
Color preset 48
100-101
Filter 143 (Pale Navy Blue)
0,241
0,32
Color preset 49
102-103
Filter 147 (Apricot)
0,534
0,404
Color preset 50
104-105
Filter 148 (Bright Rose)
0,617
0,302
Color preset 51
106-107
Filter 152 (Pale Gold)
0,472
0,4
Color preset 52
108-109
Filter 154 (Pale Rose)
0,465
0,393
Color preset 53
110-111
Filter 157 (Pink)
0,558
0,348
Color preset 54
112-113
Filter 158 (Deep Orange)
0,612
0,387
Color preset 55
114-115
Filter 161 (Slate Blue)
0,25
0,291
Color preset 56
116-117
Filter 162 (Bastard Amber)
0,458
0,402
Color preset 57
118-119
Filter 164 (Flame Red)
0,663
0,327
Color preset 58
120-121
Filter 165 (Daylight Blue)
0,211
0,273
Color preset 59
122-123
Filter 169 (Lilac Tint)
0,418
0,372
Color preset 60
124-125
Filter 170 (Deep Lavender)
0,412
0,317
Color preset 61
126-127
Filter 172 (Lagoon Blue)
0,151
0,332
Color preset 62
128-129
Filter 174 (Dark Steel Blue)
0,302
0,33
Page 12
ENGLISH OPERATION MANUAL
BRITEQ
®
10/12 BT-THEATRE 261FC
Color preset 63
130-131
Filter 180 (Dark Lavender)
0,283
0,164
Color preset 64
132-133
Filter 181 (Congo Blue)
0,187
0,058
Color preset 65
134-135
Filter 182 (Light Red)
0,686
0,311
Color preset 66
136-137
Filter 194 (Surprise Pink)
0,364
0,293
Color preset 67
138-139
Filter 197 (Alice Blue)
0,235
0,225
Color preset 68
140-141
Filter 200 (double C.T. Blue)
0,25
0,256
Color preset 69
142-143
Filter 201 (Full C.T. Blue)
0,33
0,339
Color preset 70
144-145
Filter 202 (Half C.T. Blue)
0,372
0,374
Color preset 71
146-147
Filter 203 (Quarter C.T. Blue)
0,398
0,39
Color preset 72
148-149
Filter 204 (Full C.T. Orange)
0,51
0,42
Color preset 73
150-151
Filter 205 (Half C.T. Orange)
0,474
0,417
Color preset 74
152-153
Filter 206 (Quarter C.T. Orange)
0,45
0,41
Color preset 75
154-155
Filter 219 (Fluorescent Green)
0,319
0,426
Color preset 76
156-157
Filter 241 (LEE Fluor 5700K)
0,324
0,396
Color preset 77
158-159
Filter 242 (LEE Fluor 4300K)
0,358
0,436
Color preset 78
160-161
Filter 247 (LEE Minus Green)
0,457
0,359
Color preset 79
162-163
Filter 248 (Half Minus Green)
0,441
0,378
Color preset 80
164-165
Filter 281 (Three Quarter C.T. Blue)
0,0349
0,35
Color preset 81
166-167
Filter 285 (Three Quarter C.T. Orange)
0,498
0,42
Color preset 82
168-169
Filter 328 (Follies Pink)
0,532
0,266
Color preset 83
170-171
Filter 352 (Glacier Blue)
0,217
0,304
Color preset 84
172-173
Filter 353 (Lighter Blue)
0,25
0,366
Color preset 85
174-175
Filter 363 (Special Medium Blue)
0,141
0,095
Color preset 86
176-177
Filter 507 (Madge)
0,668
0,331
Color preset 87
178-179
Filter 706 (King False Lavender)
0,271
0,168
Color preset 88
180-181
Filter 711 (Cold Blue)
0,319
0,318
Color preset 89
182-183
Filter 724 (Ocean Blue)
0,251
0,339
Color preset 90
184-185
Filter 728 (Steel Green)
0,358
0,402
Color preset 91
186-187
Filter 747 (Easy White)
0,497
0,396
Color preset 92
188-189
Filter 778 (Millennium Gold)
0,628
0,369
Color preset 93
190-191
Filter 793 (Vanity Fair)
0,591
0,258
Color preset 94
192-193
Filter 798 (Chrysalis Pink)
0,302
0,122
MAINTENANCE
• Make sure the area below the installation place is free from unwanted persons during servicing.
• Switch off the unit, unplug the mains cable and wait until the unit has been cooled down.
During inspection the following points should be checked:
• All screws used for installing the device and any of its parts should be tightly fastened and may not be
corroded.
• Housings, fixations and installations spots (ceiling, truss, suspensions) should be totally free from any
deformation.
• When an optical lens is visibly damaged due to cracks or deep scratches, it must be replaced.
• The mains cables must be in impeccable condition and should be replaced immediately when even a small
problem is detected.
• In order to protect the device from overheat the cooling fans (if any) and ventilation openings should be
cleaned monthly.
• The interior of the device should be cleaned annually using a vacuum cleaner or air-jet.
• The cleaning of internal and external optical lenses and/or mirrors must be carried out periodically to optimize
light output. Cleaning frequency depends on the environment in which the fixture operates: damp, smoky or
particularly dirty surroundings can cause greater accumulation of dirt on the unit’s optics.
• Clean with a soft cloth using normal glass cleaning products.
• Always dry the parts carefully.
Attention: We strongly recommend internal cleaning to be carried out by qualified personnel!
Page 13
ENGLISH OPERATION MANUAL
BRITEQ
®
11/12 BT-THEATRE 261FC
SPECIFICATIONS
This unit is radio-interference suppressed. This product meets the requirements of the current European and
national guidelines. Conformity has been established and the relevant statements and documents have been
deposited by the manufacturer.
Mains Input: AC 110 - 240V, 50/60Hz
Fuse: T5A / 250V (20x5mm)
Power consumption (max): 230 Watts
Power connections: PowerCON® compatible input / output
DMX connections: 3&5 pin-XLR male / female inputs + outputs
Lamp: RGBALC LED 200W
CRI: >93
Beam Angle: manual zoom 15° ~ 50°
Field Angle: 30° ~ 70°
IP-Rating: IP20
Operating Temperature: 0°C – 45°C
Size: See drawing
Weight: 8,2 kg
DIMENSIONS:
Page 14
ENGLISH OPERATION MANUAL
BRITEQ
®
12/12 BT-THEATRE 261FC
LUX CHART (CCT: 3200K)
LUX CHART (FULL ON)
The information might be modified without prior notice
You can download the latest version of this user manual on our website: www.briteq-lighting.com
Page 15
Page 16
Loading...