Britax Advansafix IV R Service Manual

1. GENERAL SAFETY INSTRUCTIONS 2. USE IN THE VEHICLE 3. APPROVAL 4. CARE AND MAINTENANCE

6. Release the two press studs on the seat cover and fold the cover forwards.

Whendoing so, pull the SecureGuard

out of the cover.

7. Loosen the 5-point harness

on the child seat as far as possible.

Tip: Pull the two shoulder straps forward while pressing the adjustment button 18.

8. Release the two opened shoulder cushions

from the Velcro strip and fold them

around the shoulder straps

DANGER Make sure that the shoulder straps 08 pass correctly through theshoul-

der cushions

9. Remove the belt clips

from the recess provided on the 44 inside of the backrest.

10. Raise the grey release plate

and push it along with the SecureGuard 26 towards

the backrest

11. Turn the grey release plate

around so that the harness buckle 20 is at the top

and the SecureGuard

is at the bottom.

12. Store the SecureGuard

in the recess provided and push the grey release plate

back into its holder until it engages with an audible click.

13. Pass the harness buckle

through the slot in the cover which is nearer

tothebackrest.

We recommend using the 5-point harness as long as possible and making the conversion only when your child starts to weigh more than 15 kg and has reached the highest position of the headrest.

1. Loosen the 5-point harness on the child seat as far as possible

2. Open the harness buckle

and place the belt clips

in the belt guides

onthesides.

3. Loosen the press studs on the backrest and fold the upper half of the cover up- wards and the lower half downwards.

4. Insert the belt clips

in the recess provided on the 44 inside of the backrest.

5. Open the two shoulder cushions

by the Velcro fasteners on the side.

6. Push the Velcro strip of the two opened shoulder cushions

under the back-

restcover and attach it to the ﬂeece strip provided. Check that the two shoulder cushions are not overlapping.

7. Pull the adjusting strap

to tighten the harness.

8. Release the two press studs on the seat cover and fold the cover forwards.

Whiledoing this, pull the harness buckle

out of the cover.

9. Raise the grey release plate

and push it along with the harness buckle

towards the backrest

10. Turn the grey release plate around

so that the SecureGuard (B) 26 is at the top

and the harness buckle (A)

is at the bottom.

11. Stow the harness buckle

in the recess provided and push the grey release plate

back into the holder until it engages with an audible click.

12. Pass the SecureGuard

through the slot in the cover with sow-on B (15-36 kg).

13. Close the two bottom press studs on the cover.

14. Close the two top press studs on the cover.

15. Close the two press studs on the upper cover of the headrest.

11. REMOVING THE 5-POINT HARNESS AND RE-ATTACHING SECUREGUARD

12. RE-ATTACHING THE 5-POINT HARNESS AND REMOVING SECUREGUARD

9 to 36 kg 9 m. ~ 12 y.

www.britax.com

User instructions

ADVANSAFIX IV R

Child seat back

1. Slide the headrest

to the lowest position.

2. Press the safety catch at the centre of the group change switch

, at the same

time moving it to the lower position for use with Group 1 (9-18 kg).

Child seat front

3. Fold the lower part of the headrest cover upwards and lay it over the headrest.

4. Open the two press studs on the inside of the headrest cover.

5. Release the two press studs on the back of the cover.

Please refer to your vehicle’s instruction manual for instructions on how to use child restraint systems. This seat can be used in vehicles with ISOFIX & Top Tether anchorage points, in vehicles with ISOFIX & 3-point harness (see type list) and in vehicles with 3-point harness.

Please refer to your vehicle’s instruction manual for information on the seats approved aschild seats for weight class 9 to 36 kg.

The

ADVANSAFIX IV R is approved for three dierent installation methods:

This means that the child seat may only be used in vehicles listed on the enclosed vehicle type list. This type list is constantly being updated. The latest version can be obtained from us or from our website at www.britax.com

You can install your child seat as follows:

Facing forwards

(in the direction of travel)

Ye s

Facing backwards

(against the direction of travel)

With 2-point harness No

With 3-point harness

Ye s

with ISOFIX ﬁxing points

(between seat surface and backrest)

Ye s

On front passenger seat Yes

On outer rear seat Yes

On centre rear seat

(with 3-point harness)

Yes

1) Installation is permitted on backward-facing car seats (e.g. in a van or minibus) only if these seats are also approved for carrying adults. The seat must not be within the activated range of an airbag.

2) The safety belt must be approved to ECE R 16 (or a comparable standard), which is indicated on the harness test label by an "E" or "e" inside a circle.

3) If there is a front airbag: Slide the car seat well back and follow the relevant instructions in the vehicle’s instruction manual.

4) It cannot be used if there is only a 2-point belt available.

Group Installation method Approval type Section

of user

instructions

1 (9-18 kg) ISOFIX + Top Tether universal A

2/3 (15-36 kg) ISOFIT + car seat belt semi-universal

2/3 (15-36 kg) Car seat belt universal B2

BRITAX RÖMER

Child seat

Testing and certiﬁcation

In accordance with ECE* R 44/04

Group Body weight

ADVANSAFIX IV R

I+II+III 9 to 36 kg

*ECE = European Standard for Child Safety Equipment

The child seat has been designed, tested and approved according to the requirements of the European Standard for Child Safety Equipment (ECE R 44/04). The E certiﬁcation mark (in a circle) and approval number can be found on the orange approval label (sticker on the child seat).

DANGER! The certiﬁcation is invalidated if you make any modiﬁcations to the

child seat. Only the manufacturer is permitted to make modiﬁcations to the child seat.

DANGER! Never secure your child or the child seat with a 2-point belt. If you

secure your child in the child seat with a 2-point belt only, this may cause serious injuries to your child in the event of an accident and could even cause death.

WARNING! The

ADVANSAFIX IV R

must be used exclusively for securing your

child in the vehicle. It is in no way suitable for use as a seat or toy in the home.

Please take the time to read these instructions carefully and always keep

them in the storage pouch provided

14 on the child seat for later reference.

The instructions must accompany the child seat if it is later passed on to athird party.

DANGER! For the protection of your child:

• Before closing the vehicle door, check that neither your child nor any parts

of the child seat can get jammed in the door.

• In the event of an accident at a collision velocity greater than 10 km/h, it is pos-

sible that the child seat may be damaged without the damage being immediately visible. In this case the child seat must be replaced. Please dispose of it properly.

• Always have the child seat examined if it has been damaged (e.g. if it falls to the

ground).

• Regularly check all important parts for damage. In particular, ensure that

all the mechanical parts are fully functional.

• Never lubricate any parts of the child seat with grease or oil.

•

Never leave your child unattended in the child seat in the vehicle.

• Have your child enter and exit the vehicle on the pavement side only.

• When not in use, protect the child seat from direct exposure to sunlight.

The child seat can become very hot in direct sunshine. Children's skin is sensitive and could be harmed as a result.

•

7KHPRUHVQXJO\WKHEHOW¿WVRYHU\RXUFKLOGVERG\WKHVDIHU\RXUFKLOGZLOOEH7KHUHfore, avoid having your child wear thick clothes under the belt.

• On long journeys, take regular breaks in order to give your child a chance to run

about and play.

• If using on the rear seat: Move the front seat far enough forward to ensure that

your child's feet will not knock against the backrest of the front seat (to prevent the risk of injury).

DANGER! For the protection of all vehicle occupants:

In the case of an emergency stop or accident, unsecured objects or people may cause injury to other occupants in the vehicle. Therefore, please always ensure that ...

QRORDGEHDULQJFRQWDFWSRLQWVDUHXVHGRWKHUWKDQWKRVHVSHFL¿HGLQWKHVH

instructions and those marked on the child seat.

• the backrests of the car seats are secured (for example, check that any fold-

down rear seat bench has snapped into place).

• all heavy or sharp-edged objects present in the vehicle (e.g. on the parcel shelf)

are held securely.

• all persons in the vehicle have their seatbelts fastened.

• the child seat is secured whenever it is in the vehicle, even if it is not carrying

a child.

WARNING! For your protection when handling the child seat:

• Never use the child seat in a free-standing position, not even for testing.

•

To avoid damage, ensure that the child seat is not jammed in between hard objects (car door, seat rails, etc.).

•

Keep the child seat in a safe place when not in use. Do not place heavy objects on the seat and do not store directly next to heat sources or in direct sunlight.

CAUTION! To protect your vehicle:

• Certain car seat covers made from more sensitive materials (e.g. velour, leather,

etc.) may show wear marks after a child seat has been used. For optimum protection of your car seat covers, we recommend using the BRITAX RÖMER car seat protector from our range of accessories.

Child seat back

16. Press the safety catch at the centre of the group change switch

, at the same

time moving it to the upper position for use with Group 2/3 (15-36 kg).

14. Close the two bottom press studs on the cover.

15. Close the two top press studs on the cover.

16. Close the two press studs on the upper cover of the headrest.

TAKING CARE OF THE HARNESS BUCKLE

To ensure the safety of your child, it is essential that the harness buckle continues tofunction correctly. Harness buckle malfunctions are usually caused by dirt accumulation or by external objects. Such malfunctions may be:

• When you press the red release button, the buckle clips are ejected only slowly.

• The buckle clips no longer engage (i.e. they pop out again when you try to push

them in).

• The buckle clips do not engage without an audible click.

• The buckle clips are dicult to push in (you feel a certain amount of resistance).

• It takes a lot of force to open the harness buckle.

Remedy

Rinse out the harness buckle so that it works perfectly again:

CLEANING THE HARNESS BUCKLE

1. Open the Velcro fastener on the crotch cushion

and remove it.

2. Remove the grey release plate

as described in Section “11. REMOVING

THE5-POINT HARNESS AND RE-ATTACHING SECUREGUARD”.

3. Place the release plate

along with the harness buckle 20 in warm water

withsome washing-up liquid for at lease one hour.

4. Thoroughly rinse the harness buckle

and dry it completely.

5. Attach the grey release plate

as described in Section 11. “ REMOVING

THE5-POINT HARNESS AND RE-ATTACHING SECUREGUARD”.

6. Attach the crotch cushion

CLEANING

CAUTION Please ensure that you use only original BRITAX replacement seat cov-

ers, as the seat cover is an integral part of the child seat and is important for correct functioning of the system. Replacement seat covers are available from your dealer.

CAUTION! The child seat must not be used without its cover.

• The seat cover can be removed and washed with a mild detergent in a washing

machine with the “Delicates” programme (30 °C). Please follow the instructions onthe washing label of the seat cover.

• The shoulder cushions can be removed and washed in lukewarm soapy water.

• The plastic parts, belts, and SecureGuard can be cleaned with soapy water.

Donotuse any aggressive cleaning agents (such as solvents).

Removing the shoulder cushions

1. Loosen the shoulder straps

as far as possible.

2. Open the shoulder cushions

by the Velcro fasteners at the side.

Child seat back

3. Bring the top tether

forward over the front of the seat.

4. Unhook the storage pouch

at the top.

5. Pull out the shoulder straps

a little so that you can see the rubber loops

oftheshoulder cushions 19 underneath.

6. Unhook the rubber loops from the plastic bars

on the shoulder strap height

adjuster

7. Pull the shoulder cushions

forwards out of the harness slots.

Reattaching the shoulder cushions

Simply follow the steps above in reverse order.

CAUTION The shoulder cushions

and belts must not be twisted or swapped over. The shoulder straps 08 must be located under the black cover band 43 inthe shoulder cushions 19.

Removing the cover Headrest

1. Open the two press studs

at the belt slots.

2. Push the headrest of the child seat to the topmost position.

3. Pull the elastic band up from the edge of the tray and pull the tabs

out

ofthetwo slots in the seat pan.

4. Pull the cover edge out of the gap between the seat pan and the inlay cushion.

5. Unhook the rubber loops

under the headrest.

Seat pan

6. Undo the Velcro fastener on the crotch cushion

and remove it.

7. Open the four press studs

on the seat and back surface.

8. Push the harness buckle

or SecureGuard 26 through the cover slot.

9. Unhook the rubber loops

at the front under the seat surface and pull the tabs

out of the seat pan.

10. Pull the rubber loops carefully out of the gap around the belt guides

11. Pull the cover edge and tabs

out of the gap between the seat pan

andtheinlay cushion.

12. Pull the rubber loops

at the top of the back of the backrest out of the gap

inthe seat pan and and unhook them.

Reattaching the cover:

Simply follow the steps above in reverse order.

CAUTION! If the child seat is installed with Method A, always install the harness

buckle

correctly, and if installed with Method B, always install SecureGuard 26

correctly. Make sure that the release plate 45 is correctly attached.

CAUTION! Check that the straps are not twisted and are laid correctly through

the slots in the cover. The rear slot in the seat cover is provided for the harness buckle

and the front slot is provided for the SecureGuard 26. The slot at the front edge

of the seat is for the harness adjusting strap 22.

2000029899 - 0/18

0506

1 cm

26 25

A properly adjusted headrest 07 ensures optimal protection for your child on the child seat. Regularly check that the height of the headrest 07 is suitable for the body height of your child: The headrest

must be adjusted so that the shoulder straps

are at the same level as your child’s shoulders, or slightly

higher.

A correctly adjusted headrest

ensures that the diagonal belt 11 is optimally positioned and gives your child optimum protection. Regularly check that the height of the headrest 07 is suitable for the body height of your child: The headrest

must be positioned so that two ﬁngers can be inserted between the headrest 07 and your child's shoulders.

To adjust the height of the headrest to ﬁt your child:

1. Press and hold the adjustment handle

on the back

ofthe headrest

2. The headrest

is now unlocked and can be moved to the desired height. When you release the adjustment handle 10, the headrest 07 locks into place.

3. Place the child seat on the car seat.

4. Sit your child on the child seat and check the height.

Repeat this procedure until the headrest

is at thecor-

rect height.

5.3 Adjusting the headrest for Group II +III (15-36 kg)

1. If your vehicle is not ﬁtted with ISOFIX insertion aids

as standard, clamp the two insertion aids 02 (which are supplied along with the seat*), with recess facing upwards, into the two ISOFIX ﬁxing points

in your

vehicle.

TIP: The ISOFIX ﬁxing points are located between

theseat surface and the backrest of the car seat.

2. Move the headrest of the car seat to its topmost position.

3. Pull the grey fabric loop at the back of the child seat

until the ISOFIX locking arms

are fully extended.

4. On both sides of the ISOFIX locking arms, squeeze the

green locking button 05 and the red release button

together. This ensures that both hooks on the ISOFIX

locking arms 04 are open and ready to use.

* The insertion aids make it easier to install the child seat using the ISOFIX ﬁxing points and they prevent damage to the car seat covers. If they are not being used, remove them and keep them in a safe place. For vehicles with a folding backrest, the insertion aids need to be removed before folding the backrest. Any problems that occur are usually caused by dirt or external objects on the insertion aids and onthe hook. Remove the dirt or external objects to resolve such problems.

5.1 Preparing ISOFIX

5.2 Adjusting the headrest for Group I (9-18 kg)

First please read the section describing the desired installation method in Section 6.

GROUP 2 (15-25 kg) & GROUP 3 (22-36 kg)

With ISOFIT + car seat belt

GROUP 1 (9-18 kg)

With ISOFIX + Top Tether

1. PREPARATORY STEPS

1.1 Follow the steps described in Section 5.1

“PREPARING ISOFIX”.

1.2 Follow the steps in Section 5.2 “ADJUSTING

THEHEADREST FOR GROUP I”.

2. PREPARING THE TOP TETHER

2.1 Unhook the snap-on hook

of the top tether 13

from the fastening on the back of the child seat.

2.2 Take the top tether

out of the pouch 14 and lay

itover the child seat.

TIP: Remove the outer rubber band only if the length

of the top tether

is not sucient for your vehicle

model.

2.3 Place the child seat in the direction of travel on an approved car seat. Adjust the backrest angle of the car seat so that the gap between the car seat and the child seat is as small as possible.

2.4 Take the top tether

and press the metal tongue 15

away from the belt to extend it, and pull the top tether

at the snap-on hook 12 until it forms a V shape.

2.5 Guide the top tether 13 past the headrest on the left and right.

3. FIXING THE TOP TETHER

Attach the snap-on hook

to the anchorage point

recommended in your vehicle's instruction manual.

CAUTION! Check that you are not using lug-

gagehooks instead of the top-tether anchorage points.

Look for the following symbol in your vehicle:

4. FASTENING THE ISOFIX

4.1 Position the two ISOFIX locking arms 04 directly infront of the two insertion aids 02.

4.2 Push the two ISOFIX locking arms

into the insertion

aids

until the ISOFIX locking arms 04 engage

onboth sides with an audible click.

DANGER! The green locking button 05 must

bevisible on both sides indicating that the child seat iscorrectly fastened.

5. PRESS THE CHILD SEAT BACKWARDS

Push the child safety seat ﬁrmly backwards as far as it will go.

6. CHECK FOR CORRECT FASTENING

Shake the child seat to check that it is securely fastened

and check the locking buttons

to make sure that the

two indicators are fully green.

7. TIGHTEN THE TOP TETHER

Tighten the top tether

, until the belt tension indicator

turns green and the top tether 13 is tight.

1. PREPARATORY STEPS

1.1 Follow the steps described in Section 5.1

„PREPARINGISOFIX”.

1.2 Follow the steps in Section 5.3 “ADJUSTING THEHEADREST FOR GROUP II+III”.

2. Place the child seat facing forward on an approved car

seat. Make sure that the backrest

is ﬂush with the back-

rest of the vehicle seat.

Tip: If the headrest of the car seat prevents the child seat

from being fastened properly, it should be removed (see vehicle’s instruction manual). Secure the removed headrest in a suitable place in the vehicle so that it will not be tossed around.

3. FASTENING THE ISOFIX

3.1 Position the two ISOFIX locking arms

directly

infrontof the two insertion aids

3.2 Push the two ISOFIX locking arms

into the inser-

tion aids

until the ISOFIX locking arms 04 engage

onboth sides with an audible click.

DANGER! The green locking button 05 must bevisi-

ble on both sides indicating that the child seat iscorrectly fastened.

4. PRESS THE CHILD SEAT BACKWARDS

Push the child safety seat ﬁrmly backwards as far as it will go.

1. Follow the steps in Section 8 „ADJUSTING THE HEAD-

REST FOR GROUP II+III“ .

2. Place the child seat on the car seat. Ensure that the back-

rest

is ﬂat against the backrest of the car seat.

Tip: If the headrest of the car seat prevents the child

seat from being fastened properly, it should be removed (see vehicle’s instruction manual). Secure the removed headrest in a suitable place in the vehicle so that it will not be tossed around.

3. Follow the steps in Section 8 “SECURING YOUR CHILD”.

5. CHECK FOR CORRECT FASTENING

Shake the child safety seat to ensure that it is securely fas-

tened, and check the locking buttons

again to ensure

that they are fully green.

6. Follow the steps in Section 8 “SECURING YOUR CHILD”.

Before every journey, for your child’s safety, check that ...

Źthe child seat is engaged on both sides with the ISOFIT locking arms in the ISOFIT

ﬁxing points and both locking buttons are fully green;

Źthe child seat is securely fastened; Źthe lap belt passes through the bright red belt guides on both sides of the seat

cushion;

Źthe

lap belt passes through the bright red

SecureGuard;

Źthe diagonal belt on the car seat belt buckle side also passes through the bright

red belt guide on the seat cushion;

Źthe diagonal belt passes through the dark red belt holder at the headrest; Źthe SICT side impact protection is correctly installed and functional; Źthe diagonal belt runs diagonally backwards;

Źthe straps are tight and not twisted; Źthe car seat belt buckle is not placed in the bright red belt guide on the seat

cushion.

Before every journey, for your child’s safety, check that ...

Źthe child seat is securely fastened; Ź the lap belt 25 passes through the bright red belt guides 28 on both sides of the

seat cushion;

Źthe

lap belt 25 passes through the bright red

SecureGuard 26;

Źthe diagonal belt 11 on the side of the car seat belt buckle 27 also passes through

the bright red belt guide

on the seat cushion;

Źthe diagonal belt

passes through the dark red belt holder 29 at the headrest;

Źthe diagonal belt 11 runs diagonally backwards; Źthe straps are tight and not twisted;

Źthe SICT side impact protection 17 is correctly installed and functional; Źthe car seat belt buckle 27 is not placed in the bright red belt guide 28 on the seat

cushion.

1. Turn the SICT

anti-clockwise

(on the side nearer thevehicle door) until there is a gap of 5 mm between it and the vehicle door or until it is fully unscrewed. Pullout the car seat belt, pass it in front of your child and into the car seat belt buckle

DANGER! Check that the car seat belt is not twist-

ed, otherwise the full protective action of the restraint system will be impaired.

2. Insert the buckle clip in the car seat belt buckle

until

there is an audible click.

3. Place the diagonal belt

and lap belt 25 on the side of the car seat belt buckle 27 in the bright redbelt guide

on the seat cushion.

DANGER! The seat belt buckle

must

notbeplaced near the bright red belt guide

4. Also place the lap belt

on the other side

oftheseatcushion in the light red belt guide 28.

DANGER! The lap belt

must be placed as

lowaspossible over your child's hips on both sides.

5. Insert the lap belt

in the bright red SecureGuard 26.

DANGER! Do not insert the diagonal belt 11 in the

bright red SecureGuard

6. Place the diagonal belt

in the dark red belt holder 29 atthe headrest 07 until it is fully in the belt holder 29 without twisting.

Tip: If the backrest 30 is covering the dark red belt

holder

, you can adjust the headrest 07 upwards.

Thediagonal belt

can now be easily inserted. You

cannow adjust the headrest 07 back to the correct height.

7. Make sure that the diagonal belt

passes over thecollarbone of your child, not the neck, and that the button on the dark red belt holder is 29 fully closed.

Tip: You can adjust the height of the headrest 07

again in the vehicle.

DANGER! The diagonal belt

must run diagonally backwards. You can adjust the position of the belt with the adjustable belt deﬂector of the vehicle.

DANGER! The diagonal belt

must never run forwards towards the belt deﬂector on the vehicle. Inthiscase, use the child seat on the back seat only.

8. Tighten the car seat belt by pulling on the diagonal belt

9. Follow the safety instructions for the installation method

concerned.

UNFASTENING YOUR CHILD AND REMOVAL:

To unfasten your child or to remove the child seat, follow the steps in Section 9 "REMOVING THE CHILD SEAT".

The

ADVANSAFIX IV R

is not permanently installed in the vehicle. It is simply secured

along with your child by the vehicle's 3-point seat belt.

UNFASTENING YOUR CHILD AND REMOVAL:

To unfasten your child or to remove the child seat, follow the steps in Section 9 “REMOVING THE CHILD SEAT”.

ŹThe shoulder straps 08 must be adjusted so that they

arehorizontal or just above your child’s shoulders.

ŹThe shoulder straps 08 must not be passed behind the

child’s back, or placed level with or above the child’s ears.

The shoulder straps are adjusted as follows:

1. Loosen the 5-point harness

on the child seat as far

aspossible.

2. Press and hold the adjustment handle

on the back

ofthe headres t07.

3. The unlocked headrest

can now be moved to the

desired height. When you release the adjustment handle

, the headrest 07 locks into place.

9. LOOSEN THE SHOULDER STRAPS

To loosen the shoulder straps, press the adjustment button

while at the same time pulling both shoulder straps 08

forward.

CAUTION! Do not pull the shoulder cushions 19.

10. OPEN THE HARNESS BUCKLE

To open the harness buckle

press the red button

onthe buckle.

11. SET THE CHILD IN THE CHILD SEAT

Place your child in the child seat. Check that the harness buckle

is facing forwards.

12. PLACE THE SHOULDER STRAPS

Pass the shoulder straps

over your child’s shoulders.

WARNING! Do not twist or swap the shoulder

straps, as this will remove their protective function.

13. FASTENING THE HARNESS BUCKLE

Take the two buckle clips

and hold them together before inserting them in the harness buckle 20 – they must make an audible click when inserted.

14. TIGHTENING THE ADJUSTMENT STRAP

Pull the adjustment strap

until the strap lies ﬂat

andsnug around your child’s body.

WARNING! The hip belts must be positioned

aslowas possible across your child's hips.

Before each journey, in order to ensure your child’s safety, make

sure that ...

Źthe child seat is engaged on both sides with the ISOFIT locking arms 04

intheISOFIX ﬁxing points 01 and that both locking buttons 05 are fully green;

Źthe child seat is securely fastened; Źthe top tether 13 is tight over the backrest of the car seat and the belt tension

indicator 16 is green;

Źthe child seat belts ﬁt snugly around the child’s body without causing constriction; Źthe shoulder straps 08 are correctly adjusted and are not twisted; Źthe shoulder cushions 19 are in the correct position for your child’s body; Źboth buckle clips 21 are fully engaged in the harness buckle 20;

Źthe SICT side impact protection 17 is correctly installed and functional.

UNFASTENING YOUR CHILD AND REMOVAL:

To unfasten your child or to remove the child seat, follow the steps in Section 9 "REMOVING THE CHILD SEAT".

The seat pan of the

ADVANSAFIX IV R

has three different angles of tilt:

To adjust the seat angle:

Pull the adjustment handle

forwards and push/slide

the seat pan 24 into the desired position.

DANGER! The seat pan

PXVWEH¿UPO\HQJDJHG

whatever the position. Pull on the seat pan 24 to check that it has engaged.

TIP: You can adjust the tilt angle of the child seat 24

even while your child is sitting on it.

Please observe the waste disposal regulations in your country.

Disposal of packaging Container for cardboard boxes

Seat cover Residual waste, waste incineration

Plastic parts To be placed in the corresponding container

according to the labels

Metal parts Container for metals

Belt straps Container for polyester

Buckle and clip Residual waste

DANGER!

If your child tries to open the car seat belt buckle 27 or insert the

diagonal belt

in the bright red SecureGuard 26, stop your vehicle immediately, or as soon as possible. Check that the child seat is correctly fastened and that your child is correctly secured. Explain to your child the dangers caused by such actions.

DANGER! If your child tries to open the car seat belt buckle

or insert the diagonal belt 11 in the bright red SecureGuard 26, stop the vehicle immediately, oras soon as possible. Check that the child safety seat is correctly fastened and that your child is correctly secured. Explain to your child the dangers caused by such actions.

DANGER! Remove the child seat from the vehicle. Never carry the child seat

inthe car if it is not fastened properly.

A) GROUP 1 (ISOFIX & TOP TETHER)

1. Loosen the top tether

by pushing the metal tongue 15 away from the belt.

2. Release the snap-on hook 12 from the anchorage point in the vehicle and lay the top tether 13 to the front over the child seat.

3. Loosen the ISOFIX fastening on both sides by squeezing the green locking button 05 and red release button 06 together.

4. Pull the seat forward and store the top tether

in the storage pouch 14 and attach the snap-on hook of the top tether 13 to the fastening on the back of the child seat.

5. Move the ISOFIX locking arms 04 back into the seat pan 24.

B) GROUP 2/3 (ISOFIT & CAR SEAT BELT / CAR SEAT BELT)

1. Press the release button on your car seat buckle

2. Open the dark red belt holder

by pressing the button on the belt holder 29

backwards and pull out the diagonal belt 11.

Only for installation method with ISOFIT:

3. To release the ISOFIT fastening, squeeze the green locking button

and red release button

WRJHWKHU¿UVWRQRQHVLGHWKHQRQWKHRWKHU

4. Move the ISOFIX locking arms

back into the seat pan 24.

GROUP 2 (15-25 kg) & GROUP 3 (22-36 kg)

With car seat belt

8. ADJUSTING THE SICT

Turn the SICT 17 anti-clockwise (on the side nearer

thevehicle door) until there is a gap of 5 mm between itand the vehicle door, or until it is fully unscrewed.

5. PREPARATORY STEPS

6. INSTALLATION & USE

7. ADJUSTING THE SEAT ANGLE

8. SECURING YOUR CHILD

9. REMOVING THE CHILD SEAT

10. DISPOSAL