Brinkmann Universal Rotisserie User Manual

OWNER’S MANUAL

MANUAL DEL PROPIETARIO

UNIVERSAL ROTISSERIE ROTISSERIE UNIVERSAL

ASSEMBLY AND OPERATING INSTRUCTIONS INSTRUCCIONES DE ARMADO Y OPERACIÓN

SAVE THIS MANUAL FOR

FUTURE REFERENCE

WARNING

READ AND FOLLOW ALL

WARNINGS AND

INSTRUCTIONS IN THIS

MANUAL TO AVOID PERSONAL

INJURY, INCLUDING DEATH OR

PROPERTY DAMAGE.

GUARDE ESTE MANUAL

PARA REFERENCIA FUTURA

ADVERTENCIA

LEA Y SIGA TODAS LAS

ADVERTENCIAS E

INSTRUCCIONES EN ESTE MANUAL PARA EVITAR LESIONES PERSONALES, INCLUSO MUERTE

O DAÑOS MATERIALES.

WE WANT YOU TO ASSEMBLE AND USE YOUR ROTISSERIE AS SAFELY AS POSSIBLE.

THE PURPOSE OF THIS SAFETY ALERT SYMBOL IS TO ATTRACT YOUR ATTENTION

TO POSSIBLE HAZARDS AS YOU ASSEMBLE AND USE YOUR ROTISSERIE.

WHEN YOU SEE THE SAFETY ALERT SYMBOL

PAY CLOSE ATTENTION TO THE INFORMATION WHICH FOLLOWS!

READ ALL SAFETY WARNINGS AND INSTRUCTIONS CAREFULLY BEFORE ASSEMBLING AND OPERATING YOUR ROTISSERIE.

WARNING

IMPORTANT SAFETY

WARNINGS

• Always check the grill prior to each use as indicated in the “Pre-Start Check List” section of the Brinkmann Owner’s Manual.

• Keep children and pets away. DO NOT allow children to use or play near the grill or rotisserie.

• DO NOT leave the grill unattended while in use.

• DO NOT use the side burner when using a rotisserie. Burner lid could be hot from prior use.

• To avoid body injury, DO NOT touch spit rod while in use or soon after use, rod can be EXTREMELY HOT.

• Keep any electrical supply cords away from water or hot surfaces.

• DO NOT operate with a damaged cord or plug.

• Turn rotisserie motor switch to “OFF” before removing plug from outlet.

• Unplug the rotisserie motor when not in use and before cleaning.

• DO NOT exceed 12 lbs. of food on the rotisserie.

• Keep a fire extinguisher acceptable for use with gas products close by. Refer to your local authority to determine proper size and type.

• For household use only. DO NOT use the grill or this rotisserie for anything other than its intended purpose.

• DO NOT use while under the influence of drugs or alcohol.

• When using an AC current rotisserie, it must be electrically grounded in accordance with local codes, or in the absence of local codes:

• In the US: The National Electrical Code – ANSI-NFPA No. 70 – Latest Edition

• In Canada: the Canadian Electrical Code – CSA C22.1

USE CAUTION AND COMMON SENSE WHEN OPERATING YOUR GAS GRILL.

FAILURE TO ADHERE TO THE SAFETY WARNINGS AND GUIDELINES IN THIS MANUAL

COULD RESULT IN SEVERE BODILY INJURY OR PROPERTY DAMAGE.

SAVE THIS MANUAL FOR FUTURE REFERENCE.

ELECTRICAL GROUNDING INSTRUCTIONS:

This appliance (rotisserie motor) is equipped with a three-prong (grounding) plug for your protection against electrical shock hazard. It should be plugged directly into a properly grounded three-prong receptacle. DO NOT cut or remove the grounding prong from this plug.

5 M5 X 10mm Screws 5 M5 Washers 5 M5 Nuts 1 Right Support Bracket

PARTS LIST:

1 Motor 5 Spit Rod Sections 2 Forks 2 Motor Mount Bracket (A & B) 1 Motor Mount Bracket 3 M6 X 10mm Screws

ASSEMBLY INSTRUCTIONS

READ ALL SAFETY WARNINGS & ASSEMBLY INSTRUCTIONS CAREFULLY

BEFORE ASSEMBLING OR OPERATING YOUR ROTISSERIE.

READ THE OWNERS MANUAL TO THE GRILL

BEFORE ASSEMBLING OR USING THIS ROTISSERIE.

THE FOLLOWING TOOLS ARE REQUIRED TO ASSEMBLE THIS UNIVERSAL ROTISSERIE:

• Phillips & Flathead Screwdrivers

• Adjustable Wrench

(Proof of purchase will be required.)

Inspect contents of the box to ensure all parts are included and undamaged.

FOR MISSING PARTS, PLEASE CALL CUSTOMER SERVICE AT 800-527-0717.

Right Support

Bracket

ASSEMBLY STEPS

Most Brinkmann grill models will use motor mount bracket (Step 1 - Step 6), if your grill is model 810-7400-S or 810-7500-S, use motor mount bracket

and skip to Step 7.

Step 1

Open grill hood and remove cooking grills. Refer to your original grill owner’s manual.

Step 2

Attach motor mount bracket 4B on the left hand side of the grill using two screws, washers and nuts.

Note: Motor mount bracket 4B may

be flipped to fit properly on certain grills.

Step 3

Attach motor mount bracket 4A to bracket 4B using one screw as shown. Keep screw loose until height adjustment has been set.

Step 4

If a notch on the right side of the grill does not exist for your spit rod, attach the spit rod support bracket to the outside right hand side of the grill using two screws, washers and nuts. (Two sets of holes are provided depending on your grill model.)

Step 5

Using a combination of sections, securely assemble the spit rod to a length that will rest on both the motor mount bracket to the spit rod bracket.

Step 6

To set the proper height for your motor mount bracket, place the motor on the motor mount bracket, place the spit rod in the motor and slide the bracket adjustment up or down until the spit rod is level. After adjustment has been made, tighten motor mount bracket 4A to bracket 4B with screw.

Motor Mount

Bracket 4A

Motor Mount

Bracket 4B

Motor Socket

Grill Body Notch

STEPS 7 - 11 ARE FOR MODELS 810-7400-S & 810-7500-S

Step 7

Open grill hood and remove cooking grills. Refer to your original grill owner’s manual.

Step 8

Attach motor mount bracket on the left hand side of the grill using two M6 X 10mm screws. Screw holes are located underneath side table.

Step 9

Slide the motor onto the support bracket. Slide spit rod into motor socket.

Step 10

Using a combination of sections, assemble the spit rod to a length that will rest on both the motor mount bracket and the spit grill body notch.

Step 11

Lock right hand side of spit rod into grill body notch.

+ 11 hidden pages