Briggs & Stratton 7800229, 7800607, 7800228, 7800419, 7800189 User Manual

...
Page 1
Not for
Reproduction
Parts Manual fo
r
8
8
8
2" STEEL DECK WALK BEHIND MOWERS
DescriptionModel No.
780041 780022 7800607 NS22675 7800419 NSP2265 7800229 NSP2265 780060 7800189 S2265 7800604 S22675 7800165 SP2265 7800605 SP22675
NS2265 NS2265
NSP22675
Briggs & Stratton Yard Power Products Group
535 Macon Road McDonough, GA, 30253 U.S.A. 800-935-2967
Manual No. Revision:
7006258
E
3/25/2011
Page 2
Not for
Reproduction
Page 3
Not for
Reproduction
s
PAGE GROUP
4 6
8 10 12 14 16
Handles & Controls (Push) Handles & Controls (Self-Propelled) Deck Assembly (Push) Deck Assemby (Self-Propelled) Engine, Blade & Front Cover Height-of-Cut Assemblies Decals
Table Of Content
22" STEEL DECK WALK BEHIND MOWERS
Manual No.
3
7006258
Page 4
Not for
Reproduction
Handles & Controls (Push)
Manual No.
7006258
22" STEEL DECK WALK BEHIND MOWERS
4
Page 5
Not for
Reproduction
Handles & Controls (Push)
Part No DescriptionItem Qty
1 7101405 1 UPPER HANDLE, Plastic, Snapper Push 2 7101321BH 1 BAIL, Plastic Handle, WBM 3 7090015 2 BOLT, 1/4-20 x 1-3/4” Round Head Square Neck, GR 2, YZ 4 2860694 3 NUT, 1/4-20, Hex Flange (Esna) YZ 5 7300649BH 2 HANDLE, Connecting, 21”/22” WBM 6 7101410 1 ROPE GUIDE (1/4-20 thread) 7 7035744 2 KNOB, 5/16-18 Wing (5/16-18 thread) (Black) 8 7091189 2 BOLT, 5/16-18 x 2” Curved Head Square Neck, GR 2 9 7090391 2 WASHER, 5/16” Internal Tooth Lock 10 7300628BH 1 HANDLE, Lower, 22” WBM 11 7101395 1 CABLE, Bail, 22” WBM 12 7101202 2 KNOB, Quick Release 13 7101199 2 BUSHING, Handle Pin 14 7101200 2 SPRING, Compression 15 7101198 2 PIN, Handle Adjust 16 7090958 2 BOLT, 5/16-18 x 1-1/2” Round Head Short Square Neck, GR 5 or 7091303 17 7090951 2 NUT, 5/16-18 Large Flange Center Lock 18 7102573 1 GRASS BAG, 22” Rear Discharge replaces 7101246 19 7101230A 1 BAG FRAME, 22” WBM (Weldment) 20 7024649 3 WIRE TIE,11” Standard Black Nylon 21 7026421 1 GRIP, Rectangular (Black)
Footnotes:
Manual No.
5
700625822" STEEL DECK WALK BEHIND MOWERS
Page 6
Not for
Reproduction
Handles & Controls (Self-Propelled)
Manual No.
7006258
22" STEEL DECK WALK BEHIND MOWERS
6
Page 7
Not for
Reproduction
Handles & Controls (Self-Propelled)
Part No DescriptionItem Qty
1 7101312 1 UPPER HANDLE, Plastic, WBM 2 7101417 1 ASSY, Control Head, 22” WBM, Single Speed (incl.Clutch Lever, Box, & Drive Cable) 3 7101321BH 1 BAIL, Plastic Handle, WBM 4 7090015 2 BOLT, 1/4-20 x 1-3/4” Round Head Square Neck, GR 2, YZ 5 2860694 3 NUT, 1/4-20, Hex Flange (Nyloc) YZ 6 7300670A 1 PLATE, Control Panel 7 95050 4 SCREW, #8-16 x 5/8” Recessed Pan Head Twin Helix (Torx) or 7100225 8 7300649BH 2 HANDLE, Connecting, 21”/22” WBM 9 7101410 1 GUIDE, Rope (1/4-20 thread) 10 7035744 2 KNOB, 5/16-18 Wing (5/16-18 thread) (Black) 11 7091189 2 BOLT, 5/16-18 x 2” Curved Head Square Neck, GR 2 12 7090391 2 WASHER, 5/16” Internal Tooth Lock 13 7300628BH 1 HANDLE, Lower, 22” WBM 14 7101395 1 CABLE, Bail, 22” WBM 15 7101202 2 KNOB, Quick Release 16 7101199 2 BUSHING, Handle Pin 17 7101200 2 SPRING, Compression 18 7101198 2 PIN, Handle Adjust 19 7090958 2 BOLT, 5/16-18 x 1-1/2” Round Head Short Square Neck, GR 5 or 7091303 20 7090951 2 NUT, 5/16-18 Large Flange Center Lock 21 7102573 1 GRASS BAG, 22” Rear Discharge or 7101246 22 7101230A 1 BAG FRAME, 22” WBM (Weldment) 23 7026421 1 GRIP, Rectangular (Black) 24 7024649 3 WIRE TIE, 11” Standard Black Nylon
Footnotes:
Manual No.
7
700625822" STEEL DECK WALK BEHIND MOWERS
Page 8
Not for
Reproduction
Deck Assembly (Push)
Manual No.
7006258
22" STEEL DECK WALK BEHIND MOWERS
8
Page 9
Not for
Reproduction
Deck Assembly (Push)
Part No DescriptionItem Qty
1 7300401D 1 DECK, 22” Walk 2 7900067 3 SCREW, 1/4-20 x 11/16” Pan Head Self-Tap (Torx) or 722848 3 7091020 4 PUSHNUT, 1/4” 4 7300855D 1 BRACKET, Chute 5 7300856D 1 PLATE, Mulch, 22” RB Scott's 6 722507 1 SPRING, Chute (Torsion) 7 7101067 1 ROD, Pivot (1/4” Dia. x 5.55”) 8 721682 1 COVER, Mulch, Plastic, Black 9 721681 1 SIDE CHUTE, Plastic, Black 10 7103347 1 GUARD, Rear 11 7091286 4 SCREW, #10-24 x 1/2” Hex Washer Self-Tap (Sems) 12 7091619 4 NUT, 3/8-16 Hex Flange Lock, YZ 13 7501055 1 * ASSY, Height-Of-Cut, Left Rear, 22” WBM, Push & Propelled 14 7501056 1 * ASSY, Height-Of-Cut, Right Rear, 22” WBM, Push & Propelled 15 7501294 1 * ASSY, Height-Of-Cut, Left Front, 22” WBM, Push 16 7501293 1 * ASSY, Height-Of-Cut, Right Front, 22” WBM, Push 17 7100633 4 GRIP, Height Latch 18 7500540 4 ASSY, Wheel & Bearing, 8 x 2 Idle, DW Tread incl. two 1-1/8” O.D. Flanged Ball Bearings (p/n
7101380) 19 7300440D 1 BAFFLE, Front, 22” WBM 20 722604 4 WASHER, 1” O.D. x .387 I.D. Flat 21 7091585 4 NUT, 3/8-16 Hex Center Lock, YZ 22 7101350 4 HUBCAP, Black 23 7300854D 1 BAFFLE, Rear, 22” Deck or 725105 24 7101243 1 DOOR, 22” Rear 25 7101070 1 ROD, Pivot, Rear Door (1/4” Dia. X 17-1/2”) 26 7101461 1 SPRING, Torsion, Rear Door, 22” WBM 27 7300668BH 1 BRACKET, Lower Handle, RH, 22” WBM 28 7300669BH 1 BRACKET, Lower Handle, LH, 22” WBM 29 7091318 2 BOLT, 5/16-18 x 3/4” Hex Head Cap, GR5 30 7091601 2 NUT, 5/16-18 Flange Lock, YZ
Footnotes:
Note: * This assembly is also shown on Height-of-Cut Assemblies page.
Manual No.
9
700625822" STEEL DECK WALK BEHIND MOWERS
Page 10
Not for
Reproduction
Deck Assemby (Self-Propelled)
Manual No.
7006258
22" STEEL DECK WALK BEHIND MOWERS
10
Page 11
Not for
Reproduction
Deck Assemby (Self-Propelled)
Part No DescriptionItem Qty
1 7300400D 1 DECK, 22” Walk, 3 N 1 2 7900067 3 SCREW, 1/4-20 x 11/16” Pan Head Self-Tap (Torx) or 722848 3 7091020 4 PUSHNUT 1/4” 4 7300855D 1 BRACKET, Chute or 726768 5 7300856D 1 PLATE, Mulch, 22” RB Scott's or 726766 6 722507 1 SPRING, Chute (Torsion) 7 7101067 1 ROD, Pivot (1/4” Dia. x 5.55”) 8 721682 1 COVER, Mulch, Plastic, Black 9 721681 1 SIDE CHUTE, Plastic, Black 10 7103347 1 GUARD, Rear or 721685 11 7091286 4 SCREW, #10-24 x 1/2” Hex Washer Self-Tap (Sems) 12 7091619 10 NUT, 3/8-16 Hex Flange Lock, YZ 13 7501055 1 * ASSY, Height-Of-Cut, Left Rear, 22” WBM 14 7501056 1 * ASSY, Height-Of-Cut, Right Rear, 22” WBM 15 7501058 1 * ASSY, Height-Of-Cut, LF, 22” WBM, Propelled 16 7501057 1 * ASSY, Height-Of-Cut, RF, 22” WBM, Propelled 17 7100633 4 GRIP, Height Latch 18 7500540 2 ASSY, Wheel & Bearing, 8 x 2 Idle, DW Tread incl. two 1-1/8” O.D. Flanged Ball Bearings (p/n
7101380) 19 7500542 2 ASSY, Drive Wheel & Bearing, 8 x 2, DW Tread incl. two 1-1/8” O.D. Flanged Ball Bearings (p/n
7101380) 20 722604 4 WASHER, 1” O.D. x .387 I.D. Flat 21 7091585 4 NUT, 3/8-16 Hex Center Lock, YZ 22 7101350 4 HUBCAP, Black 23 7102671 1 SPACER, .526" ID, .840" OD, .502" Wide (Was 720508) 24 7101243 1 DOOR, 22” Rear 25 7101070 1 ROD, Pivot, Rear Door (1/4” Dia. X 17-1/2”) 26 7101461 1 SPRING, Torsion, Rear Door, 22” WBM 27 7300668BH 1 BRACKET, Lower Handle, RH, 22” WBM 28 7300669BH 1 BRACKET, Lower Handle, LH, 22” WBM 29 7091811 2 BOLT, 5/16-18 x 5/8” Hex Flange Lock, YZ 30 7091601 3 NUT, 5/16-18 Flange Lock, YZ 31 7014341 4 RING, External Retaining (Waldes 5133-50) 32 7101207 2 GEAR, Pinion, 22” WBM, Front Wheel Drive 33 7101402 2 DUST SHIELD, Forward, 22” WBM 34 7900054 4 SCREW, 3/8-16 x 3/4” Hex Head Cap, GR 5, YZ 35 7101206 1 TRANSMISSION, 22” WBM Single Speed, Front Wheel Drive used on SP2265 & NSP22656 36 7101270 2 DRIVE PIN, 22” WBM, Front Wheel Drive 37 7300854D 1 BAFFLE, Rear, 22” Deck or 725105 38 7300440D 1 BAFFLE, Front, 22” WBM 39 722410 1 SPRING, Compression
Footnotes:
Note: * This assembly is also shown on Height-of-Cut Assemblies page.
11
Manual No.
700625822" STEEL DECK WALK BEHIND MOWERS
Page 12
Not for
Reproduction
Engine, Blade & Front Cover
Manual No.
7006258
22" STEEL DECK WALK BEHIND MOWERS
12
Page 13
Not for
Reproduction
Engine, Blade & Front Cove
r
Part No DescriptionItem Qty
1 7100851 1 BLADE, 22”, Walk Mower 2 7101449 1 ASSEMBLY, Engine Spacer, 22” WBM, Self-Propelled Includes 7101209 (spacer) & 7101448
(3) (bushings) 3 7101195 1 FRONT DECK COVER, 22” Front Wheel Drive 4 7101310 1 FRONT DECK COVER, Rear Discharge WBM 5 7900018 2 SCREW, 4.8 x 1.59 x 13mm, Round Washer Head Hi-Lo (Torx) 6 720351 3 BOLT, 3/8-16 NS x 2-1/2” 7 7090324 3 SCREW, 3/8-16 x 1” Hex Washer Self-Tap 8 7100763 1 PULLEY, Engine, 22” Deck, Single Speed 9 722884 1 SCREW, #8-11 x 5/8” Poly 10 7101193 1 ** BELT, Drive (3L Section, 33.75” effective length) 11 7100740 1 BLADE HUB, 22” Deck, Self Propelled 12 7100862 1 BLADE HUB, 22” Deck, Push 13 721890 1 WASHER, .38” I.D. x 1.183 O.D. Bellville 14 7090824 1 SCREW, 3/8-24 x 1-1/4” Hex Head Cap, GR 5 used on push models 15 720209 1 BOLT, 3/8-24 x 3-1/4” Hex Head, GR 8 used on self-propelled models 16 124T02-0650-B3 1 * ENGINE, B&S, 650 Series X-Spec (used on 7800165 & 7800189 models) 16 124L02-0650-F3 1 * ENGINE, B&S, 650 Series X-Spec (used on 7800228 & 7800229 models) 16 124L02-4650-F3 1 * ENGINE, B&S, 650 Series X-Spec (used on 7800418 & 7800419 models) 16 126T02-0675-B3 1 * ENGINE, B&S, 675 Series X-Spec (used on 7800604 model) 16 126T02-0675-B3 1 * ENGINE, B&S, 675 Series X-Spec (used on 7800605 model) 16 126L02-4675-F3 1 * ENGINE, B&S, 675 Series X-Spec (used on 7800607 & 7800608 models)
Footnotes:
NOTE: * Purchase engine parts from engine manufacturer dealer. NOTE: ** Part number appears on belt.
13
Manual No.
700625822" STEEL DECK WALK BEHIND MOWERS
Page 14
Not for
Reproduction
Height-of-Cut Assemblies
Manual No.
7006258
22" STEEL DECK WALK BEHIND MOWERS
14
Page 15
Not for
Reproduction
Height-of-Cut Assemblies
Part No DescriptionItem Qty
1 7501056 1 * ASSY, Height-Of-Cut, Right Rear, 22” WBM, Push & Propelled 2 7501055 1 * ASSY, Height-Of-Cut, Left Rear, 22” WBM, Push & Propelled 3 7501057 1 * ASSY, Height-Of-Cut, RF, 22” WBM, Propelled 4 7501058 1 * ASSY, Height-Of-Cut, LF, 22” WBM, Propelled 5 7501293 1 * ASSY, Height-Of-Cut, Right Front, 22” WBM, Push 6 7501294 1 * ASSY, Height-Of-Cut, Left Front, 22” WBM, Push 7 7091497 1 SCREW, 3/8-16 x 1-1/2” Hex Head Cap, GR 5, YZ 8 7900047 1 WASHER, .391 x 1” x 14 Ga. Flat 9 7900046 1 WASHER, .76 x 1.25 x .180 Flat 10 7101205 1 LEVER, Height-Of-Cut, 22” WBM 11 7500409 1 ASSY, Rear Axle, RH 22” WBM 12 7500408 1 ASSY, Rear Axle, LH 22” WBM 13 722611 1 WASHER, 1” I.D. x 1.64 O.D. Bellville 14 7300529 1 INDEX PLATE, Height-Of-Cut, Rear 15 721899 1 SPACER, Height Adjust 16 7013847 1 RETAINER, 3/8” Bolt 17 720118 1 RING, .906 I.D. x .078 Thick, External Retaining 18 7500404 1 ASSY, Front Axle 22”, Propelled 19 7101212 1 LEVER, Height-Of-Cut, 22” WBM 20 7300528 1 INDEX PLATE, Height-Of-Cut, Front Right, 22” WBM 21 7300527 1 INDEX PLATE, Height-Of-Cut, Front Left, 22” WBM 22 720685 1 RETAINER, Bearing 23 720761 1 BALL BEARING, 1/2 I.D. x 1-1/8” O. D. Flanged w/seal 24 7500476 1 ASSY, Front Axle, 22” WBM, Push
Footnotes:
Note: * This assembly is also shown on Deck Assemby page.
15
Manual No.
700625822" STEEL DECK WALK BEHIND MOWERS
Page 16
Not for
Reproduction
Decals
Manual No.
7006258
22" STEEL DECK WALK BEHIND MOWERS
16
Page 17
Not for
Reproduction
Part No DescriptionItem Qty
1 7102153 1 DECAL, Briggs Engine, Snapper 2 7101537 1 DECAL, Front Cover, 22” Snapper, Push 3 7101538 1 DECAL, Front Cover, 22” Snapper, Front Wheel Drive 4 7102152 1 DECAL, Briggs Engine, 650 Series 5 7102151 1 DECAL, Briggs Engine, 675 Series 6 7102303 1 DECAL, Control Head, Single Speed, Snapper 7 7101394 1 DECAL, Warning, Rear Discharge Door 8 7102746 1 DECAL, Spark Arrestor 9 7102275 1 DECAL, Customer Service, MY08, Snapper 10 7013010 1 DECAL, Danger, Cut Finger
Decals
Footnotes:
17
Manual No.
700625822" STEEL DECK WALK BEHIND MOWERS
Page 18
Not for
Reproduction
Page 19
Not for
Reproduction
Page 20
Not for
Reproduction
Parts Manual fo
r
©
22" STEEL DECK WALK BEHIND MOWERS
IT IS THE POLICY OF BRIGGS & STRATTON CORP. TO IMPROVE ITS
PRODUCTS WHENEVER IT IS POSSIBLE AND PRACTICAL TO DO SO.
WE RESERVE THE RIGHT TO MAKE CHANGES OR ADD
IMPROVEMENTS AT ANY TIME WITHOUT INCURRING ANY OBLIGATION
TO MAKE SUCH CHANGES ON PRODUCTS MANUFACTURED
Briggs & Stratton Yard Power Products Group
535 Macon Road McDonough, GA, 30253 U.S.A. 800-935-2967
www.snapper.com
Copyright Milwaukee, WI USA. All Rights Reserved
Briggs & Stratton Corporation
2011
Manual No. 7006258
Revision:
E 3/25/2011
Loading...