WIPCG-106GN
User’s Guide
IEEE 802.11BGN module
Federal Communication Commission Interference
Statement
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there is no
guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try
to correct the interference by one of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and
receiver.
- Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician
for help.
FCC Caution: Any changes or modifications not expressly
approved by the party responsible for compliance could void the
user's authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation
is subject to the following two conditions: (1) this device may not
cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause
undesired operation.
IMPORTANT NOTE:
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set
forth for an uncontrolled environment. This equipment should be
installed and operated with minimum distance 20cm between
the radiator & your body.
This transmitter must not be co-located or operating in
conjunction with any other antenna or transmitter.
IEEE 802.11b or 802.11g operation of this product in the U.S.A.
is firmware-limited to channels 1 through 11.
This device is intended only for OEM integrators under the
following conditions:
1) The antenna must be installed such that 20 cm is
maintained between the antenna and users, and
2) The transmitter module may not be co-located with
any other transmitter or antenna,
3) For all products market in US, OEM has to limit the
operation channels in CH1 to CH11 for 2.4G band by
supplied firmware programming tool. OEM shall not
supply any tool or info to the end-user regarding to
Regulatory Domain change.
As long as 3 conditions above are met, further transmitter test
will not be required. However, the OEM integrator is still
responsible for testing their end-product for any additional
compliance requirements required with this module installed.
IMPORTANT NOTE: In the event that these conditions can not
be met (for example certain laptop configurations or co-location
with another transmitter), then the FCC authorization is no
longer considered valid and the FCC ID can not be used on the
final product. In these circumstances, the OEM integrator will be
responsible for re-evaluating the end product (including the
transmitter) and obtaining a separate FCC authorization.
End Product Labeling
This transmitter module is authorized only for use in device
where the antenna may be installed such that 20 cm may be
maintained between the antenna and users. The final end
product must be labeled in a visible area with the following:
“Contains FCC ID: XV4-WCB-100A”.
Manual Information To the End User
The OEM integrator has to be aware not to provide information
to the end user regarding how to install or remove this RF
module in the user’s manual of the end product which
integrates this module.
The end user manual shall include all required regulatory
information/warning as show in this manual.
Table of Contents
Introduction
While Orthogonal Frequency Division Multiplexing (OFDM) is
Introduction……………………………………………..1
Hardware Installation………………………………….2
adopted by 802.11bgn for the high-speed transfer rate in a
2.4GHz range. Gemtek’s WIPCG-106GN fully utilizes the
benefits of 802.11bg and 802.11n-draft standard on the proven
compatibility between two transfer modes and the high speed
bit transfer that is desirable for multimedia application in
Wireless environment.
The internal Wireless LAN module allows your system (for
example, your notebook) to connect wirelessly to other
802.11-enabled systems, devices, or network.
Features
The WIPCG-106GN has the following features:
Wireless LAN Data rates of 1Mbps to 54Mbps for 802.11g ,
1Mbps to 11Mbps for 802.11b, and 150Mbps for 802.11n
draft.
Wireless security using WPA with TKIP encryption, 802.1X
with EAP-type Authentication
Hardware Installation
must be installed to provide a separation distance of at least 20
cm from all persons and must not be co-located or operating in
Please follow the instruction to install your 11BGN WiFi module
on your system :
Your computer comes with a unique pin holes, which allows the
system to add wireless LAN (IEEE802.11bg, IEEE802.11n
draft ).
Step 1 Insert the WiFi module to the pin holes.
Step 2 Connect the antenna.
Congratulations! You have just completed the Wireless LAN
hardware installation. When you boot up the computer, you
conjunction with any other antenna or transmitter.
should expect to see the wireless LAN connection capacity.
IMPORTANT NOTE: To comply with FCC RF exposure
compliance requirements, the antenna used for this transmitter
Loading...