Breville LAH400WHT User Manual

the Smart Mist

Instruction Book - LAH400

TM

Humidifier

LAH400_ANZ_IB_A19.indd 1 27/2/19 8:50 am

Contents

IMPORTANT
SAFEGUARDS

2 Breville Recommends Safety First
8 Components
9 Control Panel
10 Features
10 Assembly
11 Functions
15 Care, Cleaning & Storage
18 Troubleshooting

BREVILLE
RECOMMENDS
SAFETY FIRST

At Breville we are very safety
conscious. We design and
manufacture consumer
products with the safety of you,
our valued customer, foremost
in mind. In addition, we ask that
you exercise a degree of care
and adhere to the following
precautions.

Product Dimension 353x230x184mm

For Room Size 20 to 40m

Noise Level Up to 43dB

Power Consumption 110W

Weight 2.4kg

Water Capacity 5L

Evaporation Rate > 260ml/h

2

READ ALL
INSTRUCTIONS BEFORE
USE AND SAVE FOR
FUTURE REFERENCE

• Carefully read all instructions
before operating the
humidifier for the first time
and save for future reference.

• Remove and safely discard
any packaging material and
promotional labels before
using the humidifier for the
first time.

• To eliminate a choking
hazard for young children,
remove and safely discard the
protective cover fitted to the
power plug of this humidifier.

• When unpacking the
humidifier, check to see you
have received all the items
listed in the parts list before
discarding the packaging.

• Always ensure the humidifier
is properly assembled before
use. Follow the instructions
provided in this book.

• Always operate the
humidifier on a stable surface.
Ensure that the surface is
level, clean and free of water
and other substances.

2

LAH400_ANZ_IB_A19.indd 2 27/2/19 8:50 am

• Do not operate the humidifier
on an incline plane. Do not
move while the humidifier is
switched on.

• Do not place the humidifier
near the edge of a bench or
table during operation.

• Do not place the humidifier
on a rug, carpet, wooden
flooring, or any other surface
that may be damaged by
exposure to water or moisture.
It is recommended that a
waterproof mat or pad is
placed under the humidifier.

• Do not operate the humidifier
on a sink drain board.

• Do not locate the humidifier
directly below or close to
a mains electricity supply
socket.

• Do not use the humidifier
without water in the water
tank.

• Do not use the humidifier
unless it has been cleaned
according to instructions.

• Mist may not be visible in
certain conditions (impacted
by light, background colour,
etc.) or at lowest setting.

• Suitable for use in dry
locations only. Do not use
outdoors or on wet surfaces.
Do not use in bathrooms,
laundry areas or similar
indoor locations.

• Never place the humidifier
where it may fall into a bath
or other water container.
Do not use or store where
it may get wet or in the
immediate surroundings of
a bath, a shower, or a
swimming pool.

• Do not use in areas where
petrol, paint, or flammable
liquids are used or stored
or where there are vapours
present. Do not use in
conjunction with or directly
next to an air freshener or
similar products.

• Do not spray any flammable
materials such as insecticides
or fragrance around the
humidifier.

• Do not use this humidifier
when you have used indoor
smoke-type repellents or
in places with oily residue,
burning incense or chemical
fumes.

• Do not pour water into any
openings except for the water
tank. Do not allow water to
enter the air outlets on top of
the humidifier.

• When filling or refilling, only
fill the water tank with cold
tap water or distilled water.
Do not use ground water or
hot water.

3

LAH400_ANZ_IB_A19.indd 3 27/2/19 8:50 am

• Always switch the humidifier
off and then unplug from the
power outlet:

- Before filling or emptying
the water tank.

- Before cleaning and
maintenance, unless
otherwise specified in this
booklet.

- Immediately after use.

• Always use clean tap or
distilled water to prevent
clogging and damage to the
transducer.

• Do not put any substance
other than water in the water
tank. Do not add fragrance or
any chemical substance into
the water. Use only water (tap,
purified, mineral, any sort
of portable water). If other
additives are used, the plastic
material and the membrane
may become discoloured
and/or damaged.

• Water in the water tank is not
suitable for drinking. Do not
drink this water, and do not
use it to feed animals or water
the plants. When you empty
the water tank, pour the
water in the water tank
down a drain.

• Do not use the humidifier
in a room with major
temperature changes as this
may cause condensation
inside the humidifier.

• If not using the humidifier for
a long time, clean and dry the
water tank before storage.

• Clean the water tank
every week.

• Always disconnect the
humidifier from the power
supply and empty the water
tank before moving. Always
carry the humidifier upright.

• It is important to check the
humidity of your ambient
air regularly. Intensive
continuous operation can
cause the ambient air to
become excessively humid.

• A comfortable humidity level
is considered to be between
40%RH to 60%RH.

• Never use the humidifier
underneath a cover such as
a blanket, pillow, etc.

• Never plug in or switch on
the humidifier without filling
the removable water tank
with water and correctly
replacing the tank onto the
base of the humidifier.

• Do not remove the mist
nozzle during operation.

• Position the humidifier so
that the mist nozzle is not
directed towards objects or a
wall as the immediate vicinity
of the air humidifier may
become damp.

4

LAH400_ANZ_IB_A19.indd 4 27/2/19 8:50 am

• The humidifier is not
intended to be operated by
means of an external timer
or separate remote-control
system or any other device
that switches the humidifier
on automatically.

• Do not use chemicals, steel
wool, metal scouring pad or
abrasive cleaners to clean
the outside of the humidifier
housing as these can
damaged the housing of the
humidifier.

• Cleaning procedures must be
routinely followed to ensure
that the humidifier continues
to operate efficiently.

• Empty any remaining water
from the water tank and
water inlet basin when the
humidifier is not in use.

• You may optionally add drops
of essential/scented oils to
the aroma tray. This will emit
a pleasant odour into the
surrounding area.

• The air humidifier transducer
is highly sensitive. Do not
touch the transducer with
bare fingers or scrape it
with any metal tools, as it
may reduce the mist output
permanently.

• Keep the humidifier
clean. Follow the cleaning
instructions provided
in this book.

IMPORTANT
SAFEGUARDS
FOR ALL
ELECTRICAL
APPLIANCES

• Fully unwind the power cord
before use.

• Connect only to a 230V or
240V power outlet.

• Do not let the power cord
hang over the edge of a bench
or table, touch hot surfaces or
become knotted.

• To protect against electric
shock, do not immerse the
power cord, power plug
or appliance in water or
any other liquid or allow
moisture to come in contact
with the part, unless it is
recommended in the cleaning
instructions.

• The appliance is not
intended for use by persons
(including children) with
reduced physical, sensory
or mental capabilities, or
lack of experience and
knowledge, unless they have
been given supervision or
instruction concerning use
of the appliance by a person
responsible for their safety.

5

LAH400_ANZ_IB_A19.indd 5 27/2/19 8:50 am

• Children should be supervised
to ensure that they do not play
with the appliance.

• It is recommended to
regularly inspect the
appliance. To avoid a hazard,
do not use the appliance if
power cord, power plug or
appliance becomes damaged
in any way. Return
the entire appliance to
the nearest authorized
Breville Service Centre for
examination and/or repair.

• Any maintenance other than
cleaning should be performed
at an authorised Breville
Service Centre.

• This appliance is for
household use only.
Do not use this appliance
for anything other than its
intended use. Do not use in
moving vehicles or boats.
Do not use outdoors.

Misuse may cause injury.

• The installation of a residual
current device (safety switch)
is recommended to provide
additional safety protection
when using electrical
appliances. It is advisable that
a safety switch with a rated
residual operating current not
exceeding 30mA be installed
in the electrical circuit
supplying the appliance.
See your electrician for
professional advice.

• During electrical storms,
the appliance should be
disconnected from the power
source at the wall socket to
prevent any electrical surges
that may arise during the
storm and which may
inadvertently cause damage
to the appliance and its
electronic componentry.

• Always turn the appliance to
the off position, switch off at
the power outlet and unplug
at the power outlet when the
appliance is not in use.

6

LAH400_ANZ_IB_A19.indd 6 27/2/19 8:50 am

• Before cleaning, always turn
the appliance to the off
position, switch off at the
power outlet, unplug at the
power outlet and remove the
power cord, if detachable,
from the appliance and allow
all parts to cool.

• Do not place this appliance
on or near a heat source, such
as hot plate, oven or heaters.

• Position the appliance at a
minimum distance of 20cm
away from walls, curtains and
other heat or steam sensitive
materials and provide
adequate space above and on
all sides for air circulation.

WARNING

To avoid electric shock, do not
connect the plug to the power
outlet when hands are wet.

FOR HOUSEHOLD USE ONLY
SAVE THESE INSTRUCTIONS

7

LAH400_ANZ_IB_A19.indd 7 27/2/19 8:50 am

Components

A

B

C

D

E

F

G

H

I

J

K
L

M

A. Mist Nozzle
B. Top Cover
C. Water Tank Handle
D. Water Tank
E. Water Purification Filter
F. Water Tank Cap
G. Heating Element
H. Water Inlet Basin
I. Blue Power Indicator Light
J. Water Buoy

K. Transducer
L. Base
M. Aroma Tray
N. Front Panel
O. Control Area
P. Remote Control

N

O

P

NOT PICTURED
Sensor (located on power cord)
Power Cord
Aroma Tray Felt Pad
Non-slip Feet

8

LAH400_ANZ_IB_A19.indd 8 27/2/19 8:50 am

Control Panel

A

B

C

D

A. Power On/Off
B. Mode
C. Mist Level Control

Scroll left or right to change the mist level.

D. Night/Sleep
E. Warm Mist
F. Timer
G. Humidity Setting

NIGHT HUMIDITY

MODE

POWER

TIMER

WARM MIST

Display Screen Icons

Auto

Night

Humidity

Health
Warm Mist

Timer

E

F

G

Baby
Water Empty

9

LAH400_ANZ_IB_A19.indd 9 27/2/19 8:50 am

Features

Assembly

WHAT IS A HUMIDIFIER?

Your Breville humidifier will assist in keeping
a comfortable and healthy environment at home
by artificially adding water vapour (moisture) to
the surrounding atmosphere. It may assist with
common winter symptoms such as dry skin,
dry throat, cracked or dry lips, dry nasal cavity,
and itchy eyes, as well as some sinus and
respiratory issues.

HOW DOES A HUMIDIFIER WORK?

Your Breville humidifier uses a high-frequency
oscillator to break water into tiny water particles.
The ventilation system then blows these water
particles into the dry air in the form of a mist
where it evaporates to increase the relative
humidity.

WHAT IS RELATIVE HUMIDITY?

Relative humidity (RH) is the amount of water
vapour in the air and it is commonly expressed
as a percentage of the maximum amount of
water vapour that the air can hold at a given
temperature. Every environment has a different
humidity level. A standard comfortable level is
considered to be between 40-60%RH.

BEFORE FIRST USE

1. Before using your humidifier for the first
time, remove all packaging material and
promotional labels.

2. Check for any missing or damaged parts
as per the components list.

3. Clean all parts according to the Care, Cleaning
& Storage section.

4. Place the humidifier on a flat surface that
will not be damaged by exposure to water
or moisture.

IMPORTANT

It is recommended that a waterproof mat or pad
is placed under the humidifier when in use.

5. Remove the cover from the top of the
humidifier and set aside.

6. Using the handle, lift and remove the water
tank from the humidifier.

7. Turn the water tank gently upside-down,
unscrew the water tank cap and fill the tank
with clean water.

IMPORTANT

Only fill the water tank with cold tap or distilled
water. Do not use ground water or hot water.

8. Replace the water tank cap securely back
onto the water tank and place the tank onto
the humidifier base.

NOTE

The water purification filter is attached to the
water tank cap. Ensure both are properly fitted
before using the humidifier.

IMPORTANT

Ensure the water tank cap is properly and tightly
screwed back onto the water tank as leakage may
occur if loose or incorrectly fitted.

10

LAH400_ANZ_IB_A19.indd 10 27/2/19 8:50 am

9. Replace the top cover with the nozzle back on
top of the water tank.

10. Connect the power plug to a 230V or 240V
power outlet and switch the outlet on.

POWER symbol will illuminate red.

The
The humidifier is now in Standby mode.

11. Touch the
activate the control panel and display screen.
The humidifier is now switched on and will
automatically begin operation in Auto mode.

POWER symbol again to

IMPORTANT

Water may remain in the water inlet basin even
though the water tank may be empty. However,
once the water in the tank and/or basin is too low
to keep the humidifier running, the humidifier
will stop working. Refill the tank with water.
Do not use the humidifier without water in the
water tank.

NOTE

Take care when removing the water tank from the
base after use as residual water may drip.

Functions

YOUR BREVILLE HUMIDIFIER

• The control panel lights will dim after

15 seconds if not touched. Touch the centre of
the control panel where the control symbols are
located to wake up the screen.

• The Timer feature can be used in any mode.

• The humidifier will check the humidity level

once every minute.

• Manual adjustment of the Mist intensity control

bar will exit any programmed settings, except
Night mode and manual Humidity setting.

• Touch and hold the

turn off the blue light in the water tank.
Repeat to turn back on.

• The humidifier will automatically turn off

if it has insufficient water to operate.
Any programmed operating setting will be
cancelled if the water tank runs empty.

SensAir™ LIVE COMFORT CONTROL

• Your Breville Smart Mist™ Humidifier has

a sensor to detect changes to humidity and
temperature in the surrounding area.

• The SensAir™ can automatically keep the

humidity in “the Sweet Spot” by setting
the appropriate level of relative humidity,
depending on ambient air temperature for
maximum comfort.

WARM MIST symbol to

OPERATING YOUR HUMIDIFIER
AUTO MODE

• AUTO mode is the default setting for the

humidifier when turned on from standby.
Auto mode can also be manually selected.

• The Timer feature and Warm Mist feature can

be used with this setting. Mist Intensity cannot
be manually adjusted.

1. Touch the
panel until the
the display screen.

2. Auto mode automatically adjusts the mist
intensity to regulate the humidity level
between 40-65%RH based on the temperature
within the room.

LAH400_ANZ_IB_A19.indd 11 27/2/19 8:50 am

MODE symbol on the control

AUTO icon illuminates on

11

NOTE

Auto mode is not recommended where room
temperatures reach above 30°C.

3. The humidifier will continue to monitor and
regulate the mist intensity as required to
maintain the relative humidity level.

4. If the Timer has not been programmed, the
humidifier will continue to operate in Auto
mode until turned off or programmed to
another mode.

NOTE

The room temperature shown on the display
screen is taken only within the vicinity of the
sensor and may be influenced by positioning,
airflow and other environmental factors. Actual
room temperature may vary.

HEALTH MODE

• In

HEALTH mode, the humidifier
automatically adjusts the mist intensity to
maintain a relative humidity level of 60% and
activates the

• The Timer feature can be used with this setting

and the Warm Mist can be turned off,
if desired. Mist Intensity cannot be manually
adjusted.

1. Touch the
panel until the

WARM MIST icon both illuminate on the

display screen.

2. Once relative humidity has reached 60%,
the humidifier will continue to monitor and
regulate the mist intensity maintaining the
60% relative humidity level.

3. If the Timer has not been programmed,
the humidifier will continue to operate
in Health mode until turned off or
programmed to another mode.

WARM MIST feature.

MODE symbol on the control

HEALTH icon and the

IMPORTANT

Any programmed operating mode will be
cancelled if the water tank runs empty.

The humidifier will automatically shut off when
there is insufficient water to operate.

BABY MODE

• In BABY mode, the humidifier automatically

adjusts the mist intensity to maintain a relative
humidity level of 55% and activates the WARM
MIST feature.

• The Timer feature can be used with this setting

and the Warm Mist can be turned off, if desired.
Mist Intensity cannot be manually adjusted.

1. Touch the
panel until the

WARM MIST icon both illuminate on the

display screen.

2. Once relative humidity has reached 55%,
the humidifier will continue to monitor and
regulate the mist intensity maintaining the
55% relative humidity level.

3. If the Timer has not been programmed, the
humidifier will continue to operate in Baby
mode until turned off or programmed to
another mode.

MODE symbol on the control

BABY icon and the

NIGHT MODE

• In NIGHT mode, the humidifier turns off the

lights, except the blue water tank light.
The humidifier will operate in Auto mode.

• The Timer feature and Warm Mist feature can

be used with this setting. Mist Intensity cannot
be manually adjusted.

NOTE

Night mode will cancel all other programmed
settings and return to Auto mode.

1. Touch the
panel. The
the display screen.

2. After 15 seconds, all the lights will turn off,
except the blue water tank light and the

NIGHT icon on the display screen.

NIGHT symbol on the control

NIGHT icon will illuminate on

NOTE

Turn off the blue water tank light manually before
setting Night mode if not needed.

3. Touch the centre of the control panel to
reactivate the control panel.

4. Touch the
The control panel lights will illuminate and
the humidifier will continue to operate in
Auto mode.

NIGHT symbol again to cancel.

12

LAH400_ANZ_IB_A19.indd 12 27/2/19 8:50 am

MANUAL MODES

This humidifier can be manually programmed
in four ways:

NOTE

Manually setting the Mist Level or Humidity
Setting will cancel any other programmed
functions.

1. MIST INTENSITY CONTROL

• This humidifier has 7 mist intensity levels which

can be manually selected between Low (1) to
High (7).

• The Timer feature and Warm Mist feature can

be used with this setting.

1. Touch or slide your finger along the

on the control panel to change the intensity.
The intensity level will show on the
display screen.

2. Select another program or touch the
POWER symbol to cancel.

2. HUMIDITY SETTING

• The humidity level can be manually selected

between 30% and 75%RH.

• The Timer feature can be used with this setting.

1. Touch the

control panel repeatedly to cycle through
30% to 75% RH. The
illuminate on the display screen.

2. When the desired relative humidity level is

displayed, it will flash 5 times before starting.
Once activated, the current humidity level will
return to the display screen.

3. Once the humidity reaches the selected level,

the humidifier will continue to monitor and
regulate as required to maintain that level,
adjusting the mist intensity and turning the
mist off and on. Touch the
symbol to check the selected relative humidity
level.

4. Touch and hold the

until the
from the display screen or touch the POWER
symbol to cancel.

5. If Warm Mist is needed, it can be selected

when the desired humidity level is above the
room humidity level.

6. If ‘- -‘ flashes on the display screen, it is a

reminder that a humidity level has not been
set. It will flash for 5 seconds, then return the
humidifier to Auto mode.

MIST LEVEL CONTROL bar

HUMIDITY symbol on the

HUMIDITY icon will

HUMIDITY

HUMIDITY symbol

HUMIDITY icon disappears

3. TIMER

• This humidifier has a Timer feature that will turn

the humidifier off after a chosen number of hours.

1. Touch the
panel repeatedly to cycle through 1 to 12 hours.
The
display screen.

2. When the desired number of hours is displayed,
it will flash 5 times before starting the
countdown. Once activated, the temperature will
return to the display screen.

3. The Timer will begin to count down in 1-hour
increments. The humidifier will automatically
turn off once the chosen time has elapsed.

4. Touch and hold the
the
screen to cancel this feature.

5. If ‘- -‘ flashes on the display screen, it is a
reminder that the timer has not been set. It will
flash for 5 seconds, then return the humidifier to
Auto mode.

TIMER symbol on the control

TIMER icon will illuminate on the

TIMER symbol until

TIMER icon disappears from the display

NOTE

When the Timer is programmed, the display screen
will alternate every 30 seconds between the current
room temperature and the remaining countdown
time.

4. WARM MIST

• This humidifier has a Warm Mist feature.

A small internal heating element will heat the
water to create a warm vapour.

WARM MIST operates automatically

• The

in Health and Baby modes or can be manually
selected in other programmes.

1. Touch the
control panel to turn on. The
icon will illuminate on the display screen
and warm mist will emit from the mist nozzle
gradually within 10-15 minutes.

2. Touch the
off.

WARM MIST symbol on the

WARM MIST

WARM MIST symbol again to turn

NOTE

Warm mist will start after the water has time to heat.
The time will vary depending on factors such as the
temperature of the water in the tank.

IMPORTANT

Any manual operating mode will be cancelled if the
water tank runs empty.

The humidifier will automatically shut off when
there is insufficient water to operate.

13

LAH400_ANZ_IB_A19.indd 13 27/2/19 8:50 am

AROMA TRAY

• Press the aroma tray on the side of the

humidifier and it will click out of the unit.

• Add 2–3 drops of essential oil (not included)

directly to the pad in the aroma tray.

• Push the aroma tray back into the humidifier

until it clicks into place.

• Turn the humidifier on and the aroma will start

emitting automatically with the mist. Increase
the mist intensity as desired.

WARNING

Never add essential oil directly to the water tank,
the water inlet basin or any other part of the
humidifier except the aroma tray felt pad. Do not
use more than 2–3 drops of oil on the aroma tray
felt pad at any one time. Only add more oil when
the aroma in the surrounding air has dissipated.

AUTO SHUT-OFF

• Once the water in the water tank and water inlet

basin is too low to keep the machine running,

WATER EMPTY symbol will illuminate

the
red on the display screen for 5 minutes and the
humidifier will stop working. The
symbol will turn red and stay illuminated.

• Fill the water tank, turn the humidifier on and

program the desired mode.

POWER

USING THE REMOTE CONTROL

The humidifier comes equipped with a remote
control which can be used to operate all the
functions on the humidifier.

NOTE

On first use, remove the transparent plastic
protector that separates the Lithium battery from
the connectors.

• A CR2025 3V Lithium battery is provided

with the remote. When it is time to replace the
battery, open the battery compartment at the
back of the remote, pushing the small arched
groove to the right and simultaneously pulling
out the battery compartment cover by pushing
the rectangular groove.

• Insert the battery, paying attention to

the polarity (+ and -). Reinsert the battery
compartment into the remote control ensuring
that the + symbol is facing upwards when
inserted. Make sure the battery compartment is
correctly secured.

• To use the remote control, point it at the display

screen on the humidifier and used within
five meters.

• HINT: When correctly inserted, the text on the

battery will be facing the bottom of the remote
and the compartment is fitted correctly when it
slides in all the way.

WARNING FOR
BUTTON BATTERIES

KEEP OUT OF REACH OF CHILDREN

• Swallowing may lead to serious injury in as little

as 2 hours or death, due to chemical burns and
potential perforation of the oesophagus.

• If you suspect your child has swallowed or

inserted a button battery immediately call the
24-hour Poisons information Centre on 13 11 26
for fast, expert advice.

• Examine devices and make sure the battery

compartment is correctly secured, e.g. that the
screw or other mechanical fastener is tightened.
Do not use if compartment is not secure.

• Dispose of used button batteries immediately

and safely. Flat batteries can still be dangerous.

• Tell others about the risk associated with button

batteries and how to keep their children safe.

14

LAH400_ANZ_IB_A19.indd 14 27/2/19 8:50 am

Care, Cleaning
& Storage

Before cleaning, ensure the power is switched
off and then remove the power plug from the
power outlet.

BREVILLE RECOMMENDS

• Only use cold water or distilled water in the

water tank.

• Change the water often to keep it fresh.

• Clean the transducer, water tank and water

basin at a minimum of once every week when
in constant use.

• Use a small brush or a cotton swab to assist with

cleaning the transducer and basin. Never use
metal or sharp objects.

• After cleaning, ensure all parts are completely

dry before using the humidifier.

NOTE

Clean the whole humidifier and make sure that
all parts are dried completely.

Use a damp cloth only.
Do not immerse the unit in water.
Clean the transducer, water tank and basin at least

once a week.

IMPORTANT

If you do not use the humidifier for a long time,
clean and dry the water tank and the water
purification filter, and all parts before storage.

TO CLEAN EXTERNAL PARTS

• Use a clean, dry cloth to clean all external

surfaces of the humidifier.

• A soft, slightly-damp cloth may be used to wipe

the external housing of the humidifier if more
thorough cleaning is required. Never use
chemical substances or scourers as this could
damage the housing and the control panel.

• Dry thoroughly before storing or using the

humidifier.

TO CLEAN INTERNAL PARTS

In cases when the water is hard (where water
contains too much calcium and magnesium),
leave heavy scale on the surface of water basin,
transducer and inner surface of the water tank.
Scale, or calcification, on the surface of transducer
will reduce the reliability of the unit.

To clean internal parts of the humidifier, create a
cleaning solution of 1-part vinegar to 1-part water.

WATER TANK

• It is important to clean the water tank regularly

and ensure it is dry before reassembling and
using the humidifier.

• To clean, create a vinegar and water solution

enough to fill the tank about half way.
Making sure the cap is replaced on the tank,
swish the solution around for a minute,
then fill the rest of the tank up with tap water.
Leave to sit for 1–2 hours, or even overnight.

• Empty and rinse well with clean water.

NOTE

To assist with emptying all the water from the
water tank, it may help to slightly shake the tank
over a sink or drain.

WARNING

Do not use chemicals, steel wool, metal scouring
pad or abrasive cleaners to clean the outside of
the humidifier housing as these may damage the
humidifier.

IMPORTANT

Cleaning procedures must be routinely followed
to ensure that the humidifier continues to operate
efficiently. Do not use the humidifier unless it has
been cleaned according to instructions.

MIST NOZZLE

• If the mist output is reducing due to

calcification, turn the top cover over and
immerse the nozzle in a vessel filled with
vinegar and water solution and soak for at least
10 minutes.

• Rinse with clean or distilled water and allow

to dry.

15

LAH400_ANZ_IB_A19.indd 15 27/2/19 8:50 am

WATER INLET BASIN

• The water inlet basin includes the water

reservoir in the base of the unit that also houses
the transducer and the heating element.

• Clean the water basin with a soft cloth. If there

is excess film or calcification on the surface,
then soak the cloth with the vinegar and water
solution and repeat the process.

• If there is film or calcification in any of the

depressions along the basin, drop a bit of
vinegar and water solution into the depression
and lightly clean it with a brush or a cotton
swab.

• Rinse with clean or distilled water and allow

to dry.

OPTIONAL CLEANING SOLUTION FOR
CALCIFICATION ISSUES

• If a build-up of calcification on the transducer

or heating element occurs and cannot be
removed with a simple vinegar and water
solution, use a de-calcifying agent or citric acid.

STRICTLY FOLLOW THE INSTRUCTIONS ON
THE PACKAGING FOR THESE CLEANING
PRODUCTS.

• Brush off any scale deposits from the transducer

and heating element surfaces using the brush or
a cotton swab.

• Rinse with clean or distilled water and allow to

dry.

WATER PURIFICATION FILTER

It is recommended that you clean the water
purification filter every time you clean the
humidifier, especially if in frequent use.

If the filter is cleaned regularly and as per
instructions, it should last for the life of the
humidifier.

• Remove the cover from the top of the humidifier

and set aside.

• Using the handle, remove the water tank from

the humidifier.

• Turn the water tank gently upside down and

remove the water tank cap.

• The water purification filter is connected to the

water tank cap. Unscrew the filter from the cap
to clean.

• Dip the filter cartridge in a vinegar and water

solution for about 10 minutes before thoroughly
rinsing with clean water. Alternatively, rinse the
filter under running tap water for a minute.

WARNING

Never use sharp or solid objects to clean the
transducer and heating element. Avoid touching
the transducer and heating element with your
fingers.

NOTE

The heating element in the base of the humidifier
will lose its stainless steel finish over time - this
is normal. It is still recommended to de-calcify
as per instructions noting that cleaning may not
bring it back to its original shine.

16

LAH400_ANZ_IB_A19.indd 16 27/2/19 8:50 am

• Once clean, place the filter in direct sunlight

and allow to dry for at least an hour.

• Reconnect the filter to the water tank cap,

then screw the cap onto the water tank.

• Turn the water tank the right-side up and

place the tank onto the base carefully.

• Place the nozzle and top cover on top of the

water tank.

STORAGE

• Never store the humidifier with water in

the unit.

• Clean as per instructions and make sure that all

parts are dry before storing.

• Allow the water tank and water inlet basin time

to dry thoroughly before storing the humidifier.

• Keep the humidifier in a dry cool place.

• Do not place anything on top of the humidifier.

17

LAH400_ANZ_IB_A19.indd 17 27/2/19 8:50 am

Troubleshooting

TROUBLESHOOTING GUIDE

Before carrying out any of the following service checks, unplug the unit from the mains.

PROBLEM POSSIBLE CAUSES WHAT TO DO

Power indicator (on/off ) red
light is off or does not work.

Water tank indicator blue light
is off or does not work.

Humidifier is not plugged into

•

the power outlet or the plug may
be loose or the power outlet is not
switched on.

No, or insufficient water in the

•

tank.

Blue light has been manually

•

turned off.

Check the power cord is connected

•

to a power outlet and turned on, then
press the power on button.

Fill the water tank.

•

Touch and hold the WARM MIST

•

symbol to turn blue light on.

The mist has a strange odour.

Abnormal noise.

The volume of the mist is
too low.

Mist is leaking out from
area surrounding the
mist nozzle.

When the humidifier is first used,

•

there may be some residual odour
that should dissipate.

Water in the tank may be dirty or

•

stagnant.

Mineral scale has built up in the

•

water inlet basin.

Essential oil.

•

Vibration in the water basin

•

because the water level is too low.

Mineral scale has built up in

•

the water inlet basin and/or the
nozzle.

Mineral scale has built up in

•

the water inlet basin and/or the
nozzle.

The cover/mist nozzle is not

•

sitting correctly.

This is normal for first use. If the

•

smell does not dissipate, check water
quality as below.

Clean the water tank and refill with

•

fresh, clean water.

Clean as per instructions.

•

If using the aroma feature, check that

•

the essential oil used is not the cause
of the odour and/or too much oil has
been added.

Fill the water tank with clean water.

•

Clean as per instructions.

•

Clean as per instructions.

•

Ensure the cover/mist nozzle has

•

been fitted correctly.

18

LAH400_ANZ_IB_A19.indd 18 27/2/19 8:50 am

PROBLEM POSSIBLE CAUSES WHAT TO DO

Mist is leaking from between
the water tank and water base.

Discolouration on the
heating element.

Lights and beeps on the unit
continue for a short time after
being disconnected from
power.

Mineral scale has built up in the

•

water inlet basin or the nozzle.

Water tank is not sitting correctly

•

on base.

This is normal.

•

This is normal.

•

Clean as per instructions.

•

Ensure water tank has been fitted on

•

the base correctly.

The element should be cleaned

•

regularly, however, discolouration
that cannot be removed is normal
with use.

Residual energy will fade in a few

•

seconds.

19

LAH400_ANZ_IB_A19.indd 19 27/2/19 8:50 am

Breville Customer Service Centre

Australian Customers
Phone: [phone]
Web: www.breville.com

New Zealand Customers

0800 273 845

Phone:
Web: www.breville.com

Breville, the Breville logo, Master Every Moment and Smart Mist

are trademarks of Breville Pty. Ltd. A.B.N. 98 000 092 928.

Due to continued product improvement, the products illustrated/photographed in this booklet

LAH400_ANZ_IB_A19.indd 20 27/2/19 8:50 am

Copyright Breville Pty. Ltd. 2019.

may vary slightly from the actual product.

LAH400 ANZ A19