Breville LAD500WHT User Manual

Download

Page 1

the Smart Dry Ultimate

Instruction Book - LAD500

™

Dehumidiﬁer

LAD500_ANZ_IB_C19.indd 1 8/4/19 1:38 pm

Page 2

Contents

2 Breville Recommends Safety First 6 Components 7 Control Panel 8 Features 8 Assembly 9 Functions 13 Care, Cleaning & Storage 16 Troubleshooting

BREVILLE RECOMMENDS SAFETY FIRST

At Breville we are very safety conscious. We design and manufacture consumer products with the safety of you, our valued customer, foremost in mind. In addition, we ask that you exercise a degree of care and adhere to the following

precautions.

IMPORTANT SAFEGUARDS

READ ALL INSTRUCTIONS BEFORE USE AND SAVE FOR

FUTURE REFERENCE

• Carefully read all instructions before operation and save for future reference.

• Remove and safely discard any packaging material and promotional labels from both the dehumidiﬁer and the air ﬁlter before using for the ﬁrst time.

• To eliminate a choking hazard for young children, remove and safely discard the protective cover ﬁtted to the power plug of this dehumidiﬁer.

• When unpacking the dehumidiﬁer, check to see you have received all the items listed in the parts list before discarding the packaging.

• The dehumidiﬁer is intended for household use only and not for commercial or industrial use. Do not use outdoors.

• Always ensure the dehumidiﬁer is properly assembled before use. Follow the instructions provided in this booklet.

• Do not place the dehumidiﬁer near the edge of a bench or table during operation. Ensure the surface is level, clean and free of water.

• Do not run the cord under carpeting or cover the cord with rugs, runners or the like. Arrange the cord away from

LAD500_ANZ_IB_C19.indd 2 8/4/19 1:38 pm

Page 3

trafﬁc areas and where it will not be tripped over.

• Do not route the power cord under furniture or appliances.

• To protect against electrical hazards, do not immerse any part of the dehumidiﬁer in water or other liquids. Do not use the dehumidiﬁer in the immediate surroundings of a bath, shower or swimming pool.

• Water in the water tank is not suitable for drinking. Do not drink this water, and do not serve to animals or use to water the plants. Pour the water down a drain.

• Always turn off and unplug the dehumidiﬁer before moving, removing the water tank, changing ﬁlters, cleaning or whenever the dehumidiﬁer is not in use.

• Do not unplug the dehumidiﬁer by pulling on the cord. Use the plug to disconnect.

• Never insert ﬁngers, pencils or any other objects through the grilles whenever the power plug is connected, in particular while the dehumidiﬁer is switched on.

• Do not operate the dehumidiﬁer with a damaged cord or plug, or if the dehumidiﬁer has been dropped or damage in any manner, return the

dehumidiﬁer to your nearest Breville service centre for examination, electrical or mechanical adjustment or repair.

• Do not use the dehumidiﬁer with an external timer, programmer or any other device that switches the dehumidiﬁer on automatically since a ﬁre risk may exist if the dehumidiﬁer is covered or positioned incorrectly.

• Do not place anything on top of the dehumidiﬁer when assembled, when in use and when stored.

• Never block the air openings, grilles and outlets, or place on a soft surface such as a bed or sofa as this could cause the unit to tip over, blocking the air inlet or outlet.

• Do not attempt to repair or adjust any electrical or mechanical functions on this unit. Doing so will void your warranty. The inside of the unit contains no user serviceable parts. All servicing should be performed by qualiﬁed personnel only.

• If the dehumidiﬁer ever tips or falls over when the water reservoir is full, immediately unplug the power cord.

LAD500_ANZ_IB_C19.indd 3 8/4/19 1:38 pm

Page 4

Ensure the unit is dried thoroughly before resuming operation.

• Keep the dehumidiﬁer and dust ﬁlters clean. Follow the cleaning instructions provided in this book.

Dehumidiﬁcation Capacity ^

Product Dimension

Water Capacity

For Room Size

Noise Level

Power Consumption

Weight

Refrigerant

^ Without the air ﬁlter

30 Litres/day (30°C 80%) 15 Litres/day (27°C 60%)

370x250x585mm

Up to 80m²

51dBa

510W

15kg

R134a (165g)

IMPORTANT SAFEGUARDS FOR ALL ELECTRICAL

APPLIANCES

• Fully unwind the power cord before use.

• Connect only to a 230V or 240V power outlet.

• Do not let the power cord hang over the edge of a bench or table, touch hot surfaces or become knotted.

• To protect against electric shock, do not immerse the power cord, power plug or appliance in water or any

other liquid or allow moisture to come in contact with the part, unless it is recommended in the cleaning instructions.

• The appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.

• Children should be supervised to ensure that they do not play with the appliance.

• It is recommended to regularly inspect the appliance. To avoid a hazard, do not use the appliance if power cord, power plug or appliance becomes damaged in any way. Return the entire appliance to the nearest authorized Breville Service Centre for examination and/or repair.

• Any maintenance other than cleaning should be performed at an authorised Breville Service Centre.

• This appliance is for household use only. Do not use this appliance for anything other than its intended use. Do not use in

LAD500_ANZ_IB_C19.indd 4 8/4/19 1:38 pm

Page 5

moving vehicles or boats. Do not use outdoors.

Misuse may cause injury.

• The installation of a residual current device (safety switch) is recommended to provide additional safety protection when using electrical appliances. It is advisable that a safety switch with a rated residual operating current not exceeding 30mA be installed in the electrical circuit supplying the appliance.

• See your electrician for professional advice.

• During electrical storms, the appliance should be disconnected from the power source at the wall socket to prevent any electrical surges that may arise during the storm and which may inadvertently cause damage to the appliance and its electronic componentry.

• Always turn the appliance to the off position, switch off at the power outlet and unplug at the power outlet when the appliance is not in use.

• Before cleaning, always turn the appliance to the off position, switch off at the power outlet, unplug at the power outlet and remove the power cord, if detachable, from the appliance and allow all parts to cool.

• Do not place this appliance on or near a heat source, such as hot plate, oven or heaters.

• Position the appliance at a minimum distance of 20cm away from walls, curtains and other heat or steam sensitive materials and provide adequate space above and on all sides for air circulation.

WARNING

To avoid electric shock, do not connect the plug to the power outlet when hands are wet.

FOR HOUSEHOLD USE ONLY SAVE THESE INSTRUCTIONS

LAD500_ANZ_IB_C19.indd 5 8/4/19 1:38 pm

Page 6

Components

D E

Front

A. Control Panel B. Carry Handle C. Air Outlet D. Water Tank Handle E. Water Tank Cover F. Water Tank G. Wheels H. Housing Body I. Air Inlet and Filter J. Continuous Drainage Outlet (with Plug) K. Pump Drainage Outlet L. Cord Storage

Back

Not Pictured

Air Filter Dust Filter Carbon Filter Pump Drainage Hose (8m) Pump Outlet Clip Pump Suction Hose (20cm) Pump Suction Joint Drainage Hose (gravity-assisted) Power Cord Water Level Sensor

LAD500_ANZ_IB_C19.indd 6 8/4/19 1:38 pm

Page 7

Control Panel

A. Humidity Setting B. Child Lock C. Night Mode D. Timer E. Pump On/Off F. Mode G. Power On/Off H. Fan Speed

I. Display Screen

CHILD LOCK

NIGHT

HUMIDITY SETTING

TIMER

MODE

LOW HIGH

SPEED

PUMP

Display Screen Icons & Lights

Auto Dehumidiﬁcation

Continuous Dehumidiﬁcation

Laundry Ventilation Pump

Relative Humidity Level (%)

Empty Me Light

Defrost Light

LAD500_ANZ_IB_C19.indd 7 8/4/19 1:38 pm

Page 8

Features

Assembly

WHAT IS A DEHUMIDIFIER?

Your Breville dehumidiﬁer is designed to reduce and maintain the level of humidity in the air as well as to prevent condensation and mildew on the ceilings and walls.

HOW DOES A DEHUMIDIFIER WORK?

Your Breville dehumidiﬁer regulates the relative humidity of your home by drawing moist, humid air from the surrounding area and passing it over cooled evaporator coils causing the moisture to condense into water. The water is dispensed into the water tank or drainage hose, while the now non-humid air is re-warmed and passed back into the room.

WHAT IS RELATIVE HUMIDITY?

Relative humidity is the amount of water vapour in the air and it is commonly expressed as a percentage of the maximum amount of water vapour that the air can hold at a given temperature. A comfortable %RH level is commonly considered to be between 40-60%RH.

BEFORE FIRST USE

1. Before using your dehumidiﬁer for the ﬁrst time, remove and safely discard any packaging material or promotional labels attached to your air dehumidiﬁer and air ﬁlter.

2. Check for any missing or damaged parts as per the components list.

3. Remove the air inlet grille and air ﬁlter as per the Filter Cleaning & Replacement section of this book. Remove all packaging material from the air ﬁlter. Ensure the air ﬁlter and the air inlet grille are ﬁtted correctly onto the dehumidiﬁer before operating.

4. Clean all parts according to the Care, Cleaning & Storage section in this book.

5. Use the carry handles and wheels to move the dehumidiﬁer.

6. Position the dehumidiﬁer away from walls, furniture and other appliances as per the illustration below.

7. Ensure that all ﬁlters, grilles, water tank and drainage hose (if applicable) are correctly installed before use.

8. Connect the power plug to a 230V or 240V outlet and switch the outlet on.

Up: 30cm or more

Right & Left: 20cm or more

Back & Front: 20cm or more

WARNING

Before ﬁrst use, remove the packaging from the air ﬁlter stored behind the air inlet grille in the back of the dehumidiﬁer (See the Care, Cleaning & Storage section of this book).

LAD500_ANZ_IB_C19.indd 8 8/4/19 1:38 pm

Page 9

Functions

USING YOUR BREVILLE DEHUMIDIFIER

1. To operate the dehumidiﬁer, press the POWER button.

2. The icon for the last mode used will

illuminate on the control panel. Another mode can be selected if desired.

3. If in Auto mode, adjust the humidity level if

desired (see Humidity Setting).

4. The dehumidiﬁer will start to operate within

5 seconds.

5. Press the

POWER button again to turn off.

NOTE

The dehumidiﬁer cannot operate if the water tank is full or is not installed correctly.

TO SELECT ONE OF THE FOUR OPERATING MODES:

Press the MODE button on the control panel until the corresponding icon ﬂashes on the display screen.

AUTO MODE

The dehumidiﬁer will operate to reach, then maintain, the humidity setting.

CONTINUOUS MODE

The dehumidiﬁer will operate on Low speed until it is manually turned off.

NOTE

This dehumidiﬁer produces heat during operation which may cause room temperatures to rise by 1°C to 4°C, especially if used in an enclosed space.

SENSAIR™ LIVE HUMIDITY CONTROL

• Your Breville Smart Dry Ultimate™

Dehumidiﬁer has a built-in sensor to detect changes in the humidity level in the air.

• The SensAir ™ live humidity indicator light

will change colour according to the relevant humidity (%).

• The LED screen provides real-time indication

of the relative humidity in the air.

HUMIDITY LEVEL

When the dehumidiﬁer is turned on, the current humidity level (%) will show on the display screen and the % icon will illuminate.

This number will adjust as the dehumidiﬁer operates.

The Humidity Setting allows you to manually set the relative humidity level (%RH) between 30% - 80% (in 5% increments), when the unit is operating in Auto mode only.

1. Press the button to increase the humidity level in 5% increments with each press. Stop once the desired humidity level is displayed.

HUMIDITY SETTING

LAUNDRY MODE

Laundry mode operates at High speed and a Low humidity setting. This assists with drying wet clothes faster when hanging indoors. It is also useful in drying wet carpets or rugs.

The chosen mode will start within 5 seconds of selection.

FAN SPEED

In both Auto and Ventilation modes, the Fan Speed can be manually selected.

1. Press the between Low or High. The light will illuminate under the selected speed.

FAN SPEED button to select

NOTE

VENTILATION MODE

Circulates ambient air without dehumidiﬁcation.

LAD500_ANZ_IB_C19.indd 9 8/4/19 1:38 pm

The fan will only operate on Low speed in Continuous mode and on High speed in Laundry mode.

Page 10

NIGHT MODE

The Night mode will automatically turn off all lights on the control panel (except the Night button light) and operate in the last setting.

1. Press the panel.

2. Within 5 seconds, the lights on the control panel will turn off, except the NIGHT

3. Press once to view current humidity level.

4. Press the NIGHT Night mode.

TIMER

The Timer operates in two ways.

• Auto Off, where the timer determines when

to turn the unit OFF, can be set when the dehumidiﬁer is turned on.

• Delayed Start, where the timer determines

when to turn the unit ON, can be set when the dehumidiﬁer is turned off.

1. Press the TIMER button.

2. The display screen will ﬂash ‘00’ and the

will illuminate.

3. Press the TIMER button to increase the time in one-hour increments, up to 24 hours.

4. The time will countdown each hour, automatically turning the dehumidiﬁer ON or OFF when it reaches ‘00’.

5. To cancel Auto Off or Delayed Start, press the the

NIGHT button on the control

button.

button twice to exit

POWER button or continue to press TIMER button until it reaches '00'.

NOTE

On Delayed Start, dehumidiﬁcation mode can be set after the delayed start time has been entered by following the steps on page 9.

WARNING

As a safety feature, the dehumidiﬁer will automatically turn off if the water tank is full, even if the countdown timer has not reached ‘00’. The dehumidiﬁer will not turn on in Delayed Start if the water tank is full.

CHILD LOCK

When the Child Lock is engaged, the buttons on the control panel are locked from use.

1. To turn on, press and hold the LOCK button until a beep sounds and the light above the button illuminates.

2. To cancel, repeat step 1 until the light above the button turns off.

CHILD

WATER DRAINAGE

During the process of dehumidiﬁcation, water is created and needs to be expelled from the dehumidiﬁer. This dehumidiﬁer offers three options to drain the water.

REMOVABLE WATER TANK (with Empty Me warning)

The removable water tank will collect water until it reaches the water level sensor when the tank is full. Once full, the on the control panel will illuminate red and the dehumidiﬁer will cease dehumidiﬁcation until the water tank is emptied.

1. Remove the water tank as per the water tank cleaning instructions in the Care, Cleaning & Storage section of this book.

EMPTY ME light

NOTE

The dehumidiﬁer will not operate if the tank is not installed correctly, even if the drainage hose is in use.

WARNING

Water from the dehumidiﬁer is not suitable for drinking. Do not drink this water, and do not serve it to animals or use to water plants.

CONTINUOUS DRAINAGE (hose drainage using gravity)

The continuous drainage outlet allows water to drain without having to monitor and empty the water tank. Ensure the hose (included) is properly inserted before starting the dehumidiﬁer.

LAD500_ANZ_IB_C19.indd 10 8/4/19 1:38 pm

Page 11

1. Locate the continuous drainage outlet on the back, right hand side of the dehumidiﬁer, underneath the air inlet grille. Remove the plug and insert one end of the hose over the connection outlet, pushing in as far as possible.

Pull out the plug

2. As the drainage is dependent on gravity for the dehumidiﬁer to drain correctly, no part of the hose should sit higher than the hose connection outlet.

3. Place the other end of the hose into a water drain, being careful that it cannot inadvertently come loose when water starts to drain.

4. The water will drain from the dehumidiﬁer directly through the hose.

WARNING

Ensure the hose is secure in both the hose connection and the drainage outlet and into the water drain.

NOTE

Ensure the plug is placed back onto the continuous drainage outlet securely when continuous drainage is not in use.

PUMP DRAINAGE

Pump drainage allows the dehumidiﬁer to empty the water tank using the hose to pump the water out of the tank when full. This is suitable for homes where there is a drain available within the vicinity of the dehumidiﬁer. It is also suitable for homes that have drainage sources higher than the dehumidiﬁer, such as a sink drain, as the pump does not rely on gravity to empty the water tank. Ensure the hoses (included) are properly inserted before turning on the dehumidiﬁer. Note, the pump suction hose can already be found in the unit, secured in place.

1. Pull the water tank half way out from the back of the dehumidiﬁer.

2. Ensure that one end of the 20cm pump suction hose is in the water tank, through the slot located in the tank lid (see illustration below) and that it hits the bottom of the tank.

The pump suction hose is inserted into the water.

3. Locate the pump suction joint on the right hand side between the tank and the dehumidiﬁer body. Ensure the other end of the pump suction hose is securely over the suction joint.

The other end is connected to the suction joint.

4. Fit the water tank back into the dehumidiﬁer, ensuring both ends of the 20cm hose piece remain securely in place.

LAD500_ANZ_IB_C19.indd 11 8/4/19 1:38 pm

Page 12

5. Locate and remove the blue pump outlet clip from the drainage outlet on the opposite side of the dehumidiﬁer, and set aside for later use. Insert one end of the 8m pump drainage hose into the pump drainage outlet, ensuring the hose is pushed in as far as possible.

Remove the blue pump outlet clip

NOTE

Keep the blue outlet pump clip in a safe place for future use if the pump drainage is no longer required.

NOTE

If the 8m hose is too long, it can be cut to the desired length.

6. Place the other end of the drainage hose into a drainage source such as a bathroom ﬂoor drain or laundry sink.

7. Press the drainage and the PUMP ON light will illuminate on the control panel. The pump will enter standby mode and will only drain once the water tank is full. The pump will stop draining after 15 minutes. This cycle will continue each time the tank is full.

PUMP button to start pump

9. Remove the drainage hose from the rear of the unit.

10. Replace the blue pump outlet clip, placing it between the ring and base of the pump outlet.

DEFROST

This dehumidiﬁer is equipped with an automatic defrost function. The evaporator may start auto-defrosting if operating in a room temperature that is less than 23°C.

1. If the

DEFROST light turns on, defrosting has automatically started. The fan will operate on HIGH during defrost and dehumidiﬁcation will stop.

2. Automatic defrost will operate for up to 5 minutes.

WARNING

Do not disconnect the plug or turn off the unit during defrost operation.

NOTE

If at any time the pump needs to be activated manually during dehumidiﬁcation, press and hold the the pump will automatically begin and run for 8 minutes, then turn off.

8. If pump drainage is no longer required, hold the PUMP button down until the PUMP ON light is off. Ensure the dehumidiﬁer is switched off and unplug from the power outlet.

LAD500_ANZ_IB_C19.indd 12 8/4/19 1:38 pm

PUMP button for 5 seconds and

Page 13

Care, Cleaning & Storage

WARNING

Before cleaning or maintenance of the dehumidiﬁer, ensure the power is switched off at the outlet, and the plug is removed.

CLEANING YOUR DEHUMIDIFIER

1. Keep the unit upright when cleaning.

2. Wipe the dehumidiﬁer housing, control panel, air inlet and outlet grilles with a soft, dry cloth.

3. To remove dirt that has built-up heavily, wipe with a slightly damp cloth only.

WARNING

WATER LEVEL SENSOR

The water level sensor is situated in a chamber found in the corner of the water tank and is held in place by the water tank cover (see illustration below). The sensor rises and falls with the level of the water, and should not be removed as it will prevent the dehumidiﬁer from operating.

If the sensor inadvertently falls out of the water tank during cleaning, replace it back into the sensor chamber, ensuring the magnetic strip faces inside towards the dehumidiﬁer.

Do Not Remove

Do not clean the control panel with a damp cloth. Do not clean the unit with gasoline, thinner or liquid detergent to avoid deformation and ﬁssion of the unit. The cloth may contain chemicals which may change the colour of the dehumidiﬁer.

NOTE

Using a brush may scratch the dehumidiﬁer. Do not use any objects that may scratch the unit.

WATER TANK CLEANING

NOTE

The dehumidiﬁer cannot operate if the tank is full or is not installed correctly. Clean the water tank once a week if used regularly.

1. Remove the water tank from the front of the dehumidiﬁer by holding the sides and pulling outwards.

2. Leaving the water tank cover in place, run tap water into the tank using the holes in the cover. Swish the water around the tank then tip to empty.

3. Wipe the outside of the water tank with a soft, dry cloth before replacing.

FOR A MORE THOROUGH CLEANING OF THE WATER TANK:

1. Remove the water tank from the dehumidiﬁer.

2. Tip any water out of the tank into a sink or drain.

3. Place the tank on a dry, level surface. Flip the handle on the water tank cover until the grooves in the handle match the grooves in the handle holders. Pull outwards on both sides of the handle to disengage.

4. Once the handle has been removed, carefully pull upwards on either side of the tank cover. Remove the cover.

5. Rinse the inside of the water tank with warm, soapy water, then rinse well with clean water. During cleaning, be careful to keep the water level sensor in place or replace if it comes out of the tank (see Water Level Sensor).

6. Once clean, ﬁt the cover back onto the water tank, and replace the handle.

7. Wipe the outside of the water tank with a soft, dry cloth before replacing into the dehumidiﬁer.

LAD500_ANZ_IB_C19.indd 13 8/4/19 1:38 pm

Page 14

WARNING

Water in the water tank is not suitable for drinking. Do not drink this water, and do not serve to animals or use to water plants.

FILTER CLEANING AND REPLACEMENT

The air inlet grille at the back of the dehumidiﬁer also acts as the ﬁlter holder.

The ﬁlter holder includes a mesh pre-ﬁlter to capture dust and pet dander, and a black carbon ﬁlter to help reduce odours and smoke.

WARNING

It is important to keep the ﬁlter clean as a dirty ﬁlter may cause a reduction in the dehumidiﬁer's performance.

NOTE

Clean the ﬁlter at least monthly, or more often if in frequent use.

1. Remove the air inlet grille from the back of the unit using the grooves on either side of the holder and pulling outwards.

2. Separate the dust ﬁlter from the grille.

3. The black carbon ﬁlter sits between the air inlet grille and the mesh dust ﬁlter as per the illustration below. Separate this ﬁlter and set aside.

4. Use a hand-tool on a vacuum cleaner (such as a brush or upholstery tool) to clean the dust from the ﬁlters, or tap the ﬁlter lightly over a garbage receptacle to loosen the dust from the ﬁlter.

DUST & CARBON FILTER FREQUENT CLEANING

1. Remove the air inlet grille from the back of the unit.

2. With the dust ﬁlter and carbon ﬁlter still attached to the air inlet grille, use a handtool on a vacuum cleaner (such as a brush or upholstery tool) to clean both sides. Alternatively, lightly tap the grille over a garbage receptacle to loosen the dust.

3. Replace the air inlet grille onto the dehumidiﬁer, inserting the bottom of the grille ﬁrst, then the top. Ensure the grille clicks into place correctly before using the dehumidiﬁer.

DUST & CARBON FILTER HEAVYDUTY CLEANING

If dirt and dust has built up, and a simple clean (as instructed above) does not remove all the debris, it is recommended that the ﬁlters be separated for cleaning.

5. If the dirt and dust has built up on the mesh dust ﬁlter, hand wash in warm, soapy water, then rinse well and dry before replacing.

WARNING

Never wet the carbon ﬁlter. This ﬁlter can be cleaned by simply tapping over a garbage receptacle.

6. Re-assemble the carbon ﬁlter and dust ﬁlter back on to the air inlet grille.

7. Replace the air inlet grille onto the dehumidiﬁer, inserting the bottom of the grille ﬁrst, then the top. Ensure the grille clicks into place correctly before using the dehumidiﬁer.

LAD500_ANZ_IB_C19.indd 14 8/4/19 1:38 pm

Page 15

AIR FILTER CLEANING

The air ﬁlter sits within a cavity at the back of the dehumidiﬁer and is held in place by the air inlet grille.

4. Place the new ﬁlter into the dehumidiﬁer, then replace the air inlet grille back onto the dehumidiﬁer to hold in place before operating.

NOTE

A dirty ﬁlter may reduce the performance of the dehumidiﬁer. Clean regularly.

1. Remove the air inlet grille to access the air ﬁlter. Use a hand-tool on a vacuum cleaner (such as a brush or upholstery tool) to clean both sides of the ﬁlter.

Air Filter Dust Filter

Carbon Filter

Air Inlet Grille

2. The air ﬁlter should be replaced every 6 months, depending on frequency of use.

AIR FILTER REPLACEMENT

Your Smart Dry Ultimate™ Dehumidiﬁer air ﬁlter should be replaced in the time frames indicated below.

• The ﬁlter life is approximately 6 months if

used 24 hours daily, or 12 months if used 12 hours daily.

• The ﬁlter life may vary to this timing,

depending on environmental conditions.

• Remove all packaging from the replacement

ﬁlter and place the ﬁlter into the unit as described below.

1. Remove the air inlet grille to access the air ﬁlter.

2. Remove the used air ﬁlter, being careful that any residue or debris that may fall from the ﬁlter does not cause damage.

3. Remove the new air ﬁlter from the packaging material.

NOTE

If the ﬁlter is not in place or not ﬁtted correctly, the dehumidiﬁer will not operate effectively and may cause damage to the dehumidiﬁer.

NOTE

The air ﬁlter has no front or back, top or bottom and can be placed in the dehumidiﬁer either way.

REPLACEMENT FILTERS

Replacement ﬁlters can be purchased from the Breville website^ or at participating retail outlets.

See the table below for the replacement product code to suit this Breville Dehumidiﬁer.

Breville Dehumidiﬁer Model No.

Filter Replacement Product Code

LAD500WHT LAD050GRY

^Delivery charges may apply.

Please contact Breville Customer Service Centre for further support.

Only use the original Breville ﬁlter specially intended for this appliance. Do not use any other ﬁlters.

STORAGE

1. Disconnect the dehumidiﬁer from the power outlet.

2. Ensure the water tank is empty and cleaned as per instruction.

3. Clean the dehumidiﬁer as per instructions.

4. Wrap the power cord around the cord storage on the back of the unit.

5. Store the dehumidiﬁer upright and avoid standing in direct sunlight if leaving for long periods.

6. Never store anything on top of the dehumidiﬁer.

LAD500_ANZ_IB_C19.indd 15 8/4/19 1:38 pm

Page 16

Troubleshooting

TROUBLESHOOTING GUIDE

Before carrying out any of the following service checks, unplug the unit from the power outlet.

PROBLEM POSSIBLE CAUSES WHAT TO DO

Dehumidiﬁer not working.

Power plug is disconnected.

•

The tank is full of water.

•

The tank is not in the right

•

position.

Plug the power cord into the power socket.

•

Empty the water tank.

•

Position the water tank correctly in the unit.

•

Dehumidiﬁcation has reduced in power.

Loud noises coming from the dehumidiﬁer.

The dehumidiﬁer suddenly stops.

Clothing dries very slowly.

No reduction of humidity in the room.

WARNING

This dehumidiﬁer uses a refrigerant compressor. The noise from the compressor turning off and on during operation is normal.

The ﬁlter is too dirty.

•

The air inlet or outlet are

•

blocked.

The dehumidiﬁer is on an

•

uneven surface.

The room humidity level may

•

be outside of the radar of the dehumidiﬁer.

The room temperature is

•

too low. The wet clothes are not

•

exposed to the air from the unit.

The room is too large for the

•

unit’s scope. Doors and windows in the

•

room are open.

Clean the ﬁlter.

•

Remove the object that is blocking the air

•

inlet or outlet.

Position the dehumidiﬁer on a smooth and

•

stable surface.

The dehumidiﬁer will start again

•

automatically when it can read the room humidity level again.

If the room temperature is too low, the

•

clothing will dry slower than usual. Place the wet clothes closer to the unit so

•

they are exposed to the air ﬂow.

Move to a smaller room.

•

Close any doors or windows in the room.

•

LAD500_ANZ_IB_C19.indd 16 8/4/19 1:38 pm

Page 17

TROUBLESHOOTING GUIDE

Possible issues not related to the dehumidiﬁers performance.

ISSUE REASON

Unit occasionally stops working.

Reduction in dehumidiﬁcation strength.

There is a bad smell while on.

Sound is coming from within the dehumidiﬁer.

The buzzer sounds.

The unit is defrosting. The unit will start again once

•

defrosting is ﬁnished.

Dehumidiﬁcation reduces in strength when the room

•

temperature is too low. The unit may stop operating when the room temperature is too low. The dehumidiﬁer stops operating when the humidity level in the room drops below the set humidity level during the Auto Dehumidiﬁcation mode.

The smell may come from the walls, furniture or other

•

household objects.

Circulation of the refrigerant may cause sound until the

•

unit is stable.

This happens when the water tank is full.

•

ERROR CODES

ERROR CODE POSSIBLE CAUSES WHAT TO DO

E2 is on the display screen.

The humidity sensor is not working.

Contact Breville customer service.

E3 is on the display screen.

E6 is on the display screen.

There is damage to the automatic defrost sensor.

The pump is not working. Contact Breville customer service.

Contact Breville customer service.

LAD500_ANZ_IB_C19.indd 17 8/4/19 1:38 pm

Page 18

Notes

LAD500_ANZ_IB_C19.indd 18 8/4/19 1:38 pm

Page 19

Notes

LAD500_ANZ_IB_C19.indd 19 8/4/19 1:38 pm

Page 20

Breville Customer Service Centre

Australian Customers Phone: 1300 139 798 Web: www.breville.com

New Zealand Customers

0800 273 845

Phone: Web: www.breville.com

Breville, the Breville logo, Master Every Moment, Smart Dry Ultimate and SenSair

are trademarks of Breville Pty. Ltd. A.B.N. 98 000 092 928.

Due to continued product improvement, the products illustrated/photographed in this booklet

LAD500_ANZ_IB_C19.indd 20 8/4/19 1:38 pm

may vary slightly from the actual product.

LAD500 ANZ C19