Bradley Smoker S53-328, S53-326 AC, S53-327 DC, S53-329 User Manual

Installation

Aerada 1000 Series Faucet

S53-326 AC Gooseneck
S53-327 DC Gooseneck

Aerada 1100 Series Faucet

Aerada 1000

Installation

S53-328 AC High Arc Infrared
S53-329 DC High Arc Infrared

Table of Contents

Aerada 1100

Supplies Required .......................2

Installation .............................4

Manual Settings ........................6

Adjustments. . . . . . . . . . . . . . . . . . . . . . . . . . .9

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . 10

Care and Maintenance . . . . . . . . . . . . . . . . . 12

Multi-Faucet Transformer Wiring . . . . . . . . . 14

IMPORTANT!

Read this entire installation manual to ensure proper installation. When
fi nished with the installation, fi le this manual with the owner or maintenance
department. Compliance and conformity to local codes and ordinances is
the responsibility of the installer.

Packing List

Separate parts from packaging and make sure all parts are accounted for

•

•

before discarding packaging material. If any parts are missing, do not begin

•

THIS
SIDE

•

UP

215-1628 Rev. A; EN 08-201
© 2008 Bradley Corporation
Page 1 of 14 5/21/08

installation until you obtain the missing parts.

Make sure that all water supply lines have been fl ushed and then completely
turned off before beginning installation. Do not use pipe dope. Debris in
supply lines can cause valves to malfunction.

Product warranties may be found under “Products” on our web site at
www.bradleycorp.com.

P.O. Box 309, Menomonee Falls, WI 53052-0309
Phone: 1-800-BRADLEY Fax: [phone]
www.bradleycorp.com

Aerada 1000/1100 Series Installation

SAFETY INFORMATION

Read this entire user guide to ensure proper installation.

Compliance and conformity to local codes and ordinances is the responsibility of
the installer.

The following safety notes must always be complied with during handling of this
product:

• Make sure there is enough space and lighting available during installation and
service.

• Do not modify or convert this Faucet; any modifi cations will void warranties.

Installation may be performed at different times of construction by

different individuals. For this reason, these instructions should be left
on-site with the facility or maintenance manager.

Pressurized plumbing fi xtures shall be installed in accordance with

manufacturer´s recommendations. The supply piping to these devices
shall be securely anchored to the building structure to prevent installed
device from unnecessary movement when operated by the user. Care
shall be exercised when installing the device to prevent marring the
exposed signifi cant surface.

EXPLANATION OF SYMBOLS

Symbol Meaning

WARNING Refers to a situation of potential danger that

may cause serious injury or death.

CAUTION Refers to a situation of potential danger that

may cause slight or medium injury or property
damage.

Refers to important information.

A

D

A

•

C

O

M

P

L

T

I

A

N

ACCESSORIES BRADLEY PART NO.

4” Cover Plate 150-221

Plugin Transformer 232-008

Hardwired Transformer (1–8 faucets) 232-009

2.2 GPM Laminar Flow for Gooseneck 269-1923

2.2 GPM Laminar Flow for Lavatory 269-1922

6V Lithium Battery CR-P2 261-010

TECHNICAL SUPPORT

For additional technical assistance, visit our website or call us:

• www.bradleycorp.com

• 1-800-BRADLEY

ORDERS

For orders, contact your local representative, visit our website or call us:

• www.bradleycorp.com

• 1-800-BRADLEY

2 5/21/08 Bradley Corporation • 215-1628 Rev. A; EN 08-201

Installation Aerada 1000/1100 Series

COMPONENT PARTS
Aerada 1100 Series

11

COMPONENT PARTS
Aerada 1000 Series

2

12

1 a/b

10

3

4

5

7

8

9

6

12

1

3

2

11

4

8

9

7

10

5

6

High Arc Components & Bradley Part Nos.

1. Spout with External Mixer opening [269-1960]

2. Shut Off Screw Assembly [269-1944]

3. Outlet Assembly Kit Lavatory Spout (.5 GPM) [269-1946]

4. Mixer Kit [269-1945]

5. 6 V Lithium Battery CR-P2 [261-010]

6. AC Adaptor Kit [269-1942]

7. Battery Holder Kit [269-1961]

8. Check Valve (1) [198-013]

9. Braided Hose (1) with inlet filter [269-1943]; Filter only [269-1948]

10. Deck Mounting Hardware Kit [269-1949]

11. Electronics Module Kit [269-1941]

12. Solenoid Valve [269-1940]

Gooseneck Components & Bradley Part Nos.

1. Spout [269-1958]

2. Shut Off Screw Assembly [269-1944]

3. Outlet Assembly Kit Spout (.5 GPM) [269-1947]

4. Gooseneck Base without opening [269-1959]

5. 6 V Lithium Battery CR-P2 [261-010]

6. AC Adaptor Kit [269-1942]

7. Battery Holder Kit [269-1961]

8. Check Valve (1) [198-013]

9. Braided Hose (1) with inlet filter [269-1943]; Filter only [269-1948]

10. Deck Mounting Hardware Kit [269-1949]

11. Electronics Module Kit [269-1941]

12. Solenoid Valve [269-1940]

Bradley Corporation • 215-1628 Rev. A; EN 08-201 5/21/08 3

Aerada 1000/1100 Series Installation

INSTALLATION

This faucet comes with all the components needed for installation,however, some
tools and supplies are not included.

• Basin Wrench

• Adjustable Wrench

• Adjustable Locking Pliers

• Plumber´s Putty

• Hex Key (supplied)

• Outlet Key (supplied)

Do not use pipe dope on faucet and supply connections. Possible

solenoid contamination could occur and will void any warranty.

Mounting of Lavatory and Gooseneck Faucet

Prerequisites

• Supply valve is installed

• Water supply lines are fl ushed properly

• For AC faucets, power outlet is installed

It is not necessary to unscrew the connection between braided hose

Do not remove protective covering from sensor until starting up faucet

Do not tighten locknut before step 4 is completed.

1 Mount cover plate if required. Plumber´s putty is recommended to seal the

and housing to install the product.

operation.

cover plate to the sink. Security pin must be located on the left side.

3 Mount bracket from underneath. Place hoses through large opening and

mounting rod through small opening. Make sure fl ange sits securely against
surface.

4 Place nut onto mounting rod and tighten with wrench.

5 If faucet was installed with cover plate, secure with basin washer, fl at washer

and locknut.

6 Install aerator and tighten with aerator key (supplied).

7 For Gooseneck faucets, tighten spout with wrench.

8 Connect braided hose with fi lter to supply valve

Cold water > white label Hot water > no label

2 Mount gasket and put faucet into sink.

For AC faucets, please refer to the plugin or hardwired transformer

9 Connect to power supply.

Result: The faucet is now mounted.

installation instructions.

4 5/21/08 Bradley Corporation • 215-1628 Rev. A; EN 08-201

Installation Aerada 1000/1100 Series

Start-up Operation

Prerequisites

• Faucet is mounted

• Water supply is on

• Water supply lines are fl ushed properly

• For AC faucets, power outlet is installed.

1 Fully open supply valves.

2 Remove all items from sink.

Test Function

1 Hold hand in front of sensor.

> Water fl ow starts

WARNING Hot water may burn your skin.

Hold hand carefully under water and remove quickly

2 For faucets with external mixer, turn mixer handle from cold to warm.

> Water temperature increases

3 Remove protective covering from sensor.

4 Wait for 15 seconds for the faucet to calibrate to its environment.

15 sec.

Result: The faucet is now activated.

3 Remove hand.

> Water fl ow stops

Result: The function is now tested.

Bradley Corporation • 215-1628 Rev. A; EN 08-201 5/21/08 5