Bradley Corporation S19-120, S19-120A, S19-120SS User Manual

S19-120, S19-120A, S19-120SS

• Exceeds American National Standard Z358.1 Specifications

• Exceeds European EN 15154-1

• Exceeds Australia/New Zealand AS4775 & AS/NZS 4020

• Easily Mounts to Wall

• Galvanized Steel Protected with BradTect® Safety Yellow Coating

• Universal Identification Sign and Inspection Tag Included

• Full, One-Year Warranty

• SpinTec™ showerheads are covered by one or more of the following patents: 8113446; D594,089;
D669,555; Reg. Comm. Des. D001079560-0001. Other patents pending.

• Classified by Underwriters Laboratory Inc. to ANSI Z358.1

• Listed by Intertek to EN 15154-1

• Certified by IAPMO OCEANA to AS4775 and AS/NZS 4020

Drench Shower with Horizontal Supply

®

Specifications

Impact-resistant plastic shower head is colored bright yellow for high visibility in emergency situations.
Also available in corrosion resistant stainless steel. Shower pull rod is stainless steel. Galvanized steel
piping is additionally protected with BradTect® safety yellow coating. Model S19-120SS is all stainless
steel construction.

Drench shower is designed to accommodate standard 8' ceiling height. ANSI

Z358.1 compliant drench showers are mounted between 82"–96" from the lower
edge of the showerhead or shroud to the floor.

This plumbing fixture is not intended to dispense water for human consumption

through drinking or for preparation of food or beverages.

Model Description

 S19-120 Drench Shower w/Horizontal Supply, Plastic Showerhead

 S19-120A Drench Shower w/Horizontal Supply, Plastic Showerhead w/

Stainless Steel Shroud

 S19-120SS Drench Shower w/Horizontal Supply, All-Stainless Steel Fixture

 S19-120SSZ Drench Shower w/Horizontal Supply, All-Stainless Steel Fixture w/

BSPP Connection/Certified to AS4775 & AS4020

 S19-2100 Navigator EFX25 - Emergency Thermostatic Mixing Valve

Recommended Option:

Navigator S19-2100 EFX25

Emergency Thermostatic Mixing Valve

Model S19-120

Model S19-120A

Satisfies ANSI Z358.1

tepid water requirements.

Page 1 of 3 9/8/2017
This information is subject to change without notice.
Bradley_DrenchShower_S19-120_A_SS

Model S19-120SS

© 2017 Bradley

P.O. Box 309, Menomonee Falls, WI 53052-0309

800 BRADLEY (800 272 3539) [phone]

bradleycorp.com

S19-120, S19-120A, S19-120SS

Drench Shower with Horizontal Supply

Standard Equipment

SpinTec™ Showerhead

Standard showerhead is 3.1" (78.7mm) diameter highly visible yellow impact-resistant
plastic (Model S19-120A includes a 10¾" [273mm] diameter corrosion-resistant
stainless steel shroud). High performance corrosion-resistant stainless steel
showerhead measures 1½" (38mm) in diameter (Model S19-120SS only). SpinTec
drench showerhead features integral 22 GPM (83.3 L) flow control, conserving water
and helping to accurately size your tepid water system.

SpinTec Flow Rate vs Inlet Pressure at Fixture

40

35

30

25

20

15

Flow Rate (gpm)

10

5

0

10 20 30 40 50 60 70 80 90

Inlet pressure at Fixture (psig)

Valve

Chrome-plated brass 1" NPT stay-open ball valve, operated by stainless steel pull rod
with triangular handle. Model S19-120SS is all stainless steel.

Pipe and Fittings

1¼" galvanized steel with BradTect® safety yellow coating. S19-120SS is all stainless
steel.

Water Supply

1" NPT Horizontal (BSPP model only)

Local codes may require the installation of a backflow prevention valve to

complete proper installation. Compliance with local codes is the responsibility
of the installer. Valve must be tested annually to verify that it is functioning
properly. Backflow prevention valves are not included with the fixture and may
be supplied by the contractor or purchased from Bradley Corporation.

Page 2 of 3 9/8/2017
This information is subject to change without notice.
Bradley_DrenchShower_S19-120_A_SS

P.O. Box 309, Menomonee Falls, WI 53052-0309

© 2017 Bradley

800 BRADLEY (800 272 3539) [phone]

bradleycorp.com