Bradley Corporation 800 Installation Manual
800 Series
Mounting Kits and Anchoring Devices
Concealed Mounting Kits
Order one mounting kit per grab bar flange.
Stud walls with wood sup ports
899-010
MATERIAL INCLUDED
2 – ¼ x 2½" PLATED
STEEL HEX HEAD LAG BOLTS
2½"
(64mm)
Partition walls
899-011
MATERIAL INCLUDED
A) 2 – ¼-20 x 1½"
PLATED STEEL HEX HEAD
MACHINE SCREWS
B) 2 CAP NUTS
C) 1 BACKING PLATE
Panel walls
899-012
MATERIAL INCLUDED
A) 2 – ¼-20 x 3"
PLATED STEEL HEX
HEAD MACHINE
SCREWS
B) 2 TOGGLE NUTS
Masonry walls
899-013
MATERIAL INCLUDED
A) 2 – ¼-20 x 1"
PLATED STEEL HEX HEAD
MACHINE SCREWS
B) 2 – ¼-20 LEAD ANCHORS
1"
(25mm)
Metal Stud Wall Mounting Kits
899-014
(CONCEALED OR EXPOSED)
MATERIAL REQUIRED
A) IN-WALL ANCHOR PLATE
899-015 (NOT INCLUDED).
SPECIFY AND ORDER
SEPARATELY – SEE ANCHOR
PLATES IN NEXT COLUMN.
B) #10 sheet metal screws
(furnished by others)
C) METAL STUD
D) 2 – ¼-20 x 1¼"
FLAT HEAD machine SCREWS.*
E) WALL DIMENSIONS (TO BE FURNISHED
IF OVER ¾").
* INCLUDED WITH MOUNTING KIT 899-014.
A
C
B, D
E
In-Wall Anchor Plates
899-015
x LENGTH (TO 96")
MATERIAL
1
⁄8" COLD ROLLED STEEL –
4" x
LENGTH AS SPECIFIED TO 96"
NOTE: SEPARATELY ORDER
899-014 MOUNTING KITS
AS REQUIRED.
INSTALLATION:
FASTEN TO STUDS BEFORE WALL APPLIED.
RECESS AS REQUIRED FOR FLUSH FINISH WALL APPLICATION.
TO ATTACH GRAB BAR, DRILL #2 (.221 DIAMETER)
HOLES THRU WALLBOARD AND ANCHOR PLATE.
ATTACH WITH ¼-20 x 1¼" PLATED PHILLIPS
OVAL HEAD ROLLOCK TAPPING SCREWS.
UNIVERSAL
ANCHOR PLATE
Block Wall Mounting Kits
C
A
B
D
E
899-016
(CONCEALED OR EXPOSED)
FRONT AN CHOR PLATE BACK AN CHOR PLATE
MATERIAL REQUIRED
A) FRONT ANCHOR PLATE 3" x 3" x
STEEL – CENTER SLOT PUNCHED AND 2 FASTENER
HOLES PRE-PUNCHED.*
B) 2 – ¼-20 x 1¼" PLATED PHILLIPS FLAT HEAD SELF
TAPPING SCREWS.*
3
⁄8-16 STEEL ZINC-PLATED TIE ROD WITH NUT.*
C) 1 –
D) BACK ANCHOR PLATE 3" x 3" x
STEEL – TAPPED FOR AND INCLUDING
AND NUT.*
E) FINISHED WALL THICKNESS (TO BE FURNISHED IF
OVER ¾").
F) MASONRY WALL (THICKNESS TO BE FURNISHED).
* INCLUDED WITH MOUNTING KIT 899-016.
F
1
⁄8" COLD ROLLED
3
⁄16" COLD ROLLED
3
⁄8-16 STUD
Page 1 of 2 6/21/2013
This information is subject to change without notice.
Bradley_GrabBar_800SeriesMountingKitsAndAnchoringDevices
P.O. Box 309, Menomonee Falls, WI 53052-0309
© 2015 Bradley
800 BRADLEY (800 272 3539) +1 262 251 6000
bradleycorp.com
Exposed Mounting Kits
800 Series
Mounting Kits and Anchoring Devices
Stud walls with wood supports
899-020
MATERIAL INCLUDED
2 – #14 x 2½" STAINLESS
STEEL PHILLIPS OVAL HEAD
SHEET METAL SCREWS
2-1/2"
(64mm)
Partition walls
899-021
MATERIAL INCLUDED
A) 2 – ¼-20 x 1
STAINLESS STEEL
PHILLIPS OVAL HEAD
MACHINE SCREWS
B) 2 CAP NUTS
C) 1 BACKING PLATE
3
⁄8"
Panel walls
899-022
MATERIAL INCLUDED
A) 2 – ¼-20 x 3"
STAINLESS STEEL
PHILLIPS OVAL HEAD
MACHINE SCREWS
B) 2 TOGGLE NUTS
Stud walls
899-026
(CONCEALED OR EXPOSED)
MATERIAL INCLUDED
4 – #10 x 2"
ZINC PLATED
FLAT HEAD
WOOD SCREW
NOTE: FOR MIRROR MOUNTING
ONLY.
(1) PER H-HANGER
Stud walls
899-027
(CONCEALED OR EXPOSED)
MATERIAL INCLUDED
4 – #10 x 1"
ZINC PLATED
PAN HEAD
WOOD SCREW
Stud walls
899-028
(EXPOSED MOUNTING)
7 – SLOTTED HEX WASHER HEAD
¼" x 2" LONG
18-8 STAINLESS STEEL
SHEET METAL
2"
(51mm)
1"
(25 mm)
1"
(25mm)
2"
(51mm)
Masonry walls
899-023
MATERIAL INCLUDED
A) 2 – ¼-20 x 1"
STAINLESS STEEL
PHILLIPS OVAL HEAD
MACHINE SCREWS
B) 2 – ¼-20 LEAD
ANCHORS
Page 2 of 2 6/21/2013
This information is subject to change without notice.
Bradley_GrabBar_800SeriesMountingKitsAndAnchoringDevices
1"
(25mm)
Stud walls
899-029
(EXPOSED MOUNTING)
10 – SLOTTED HEX WASHER HEAD
¼" x 2" LONG
18-8 STAINLESS STEEL
SHEET METAL
2"
(51mm)
P.O. Box 309, Menomonee Falls, WI 53052-0309
800 BRADLEY (800 272 3539) +1 262 251 6000
© 2015 Bradley
bradleycorp.com
Loading...