ETAL100.0610-1
User's manual
Version: 1.00 (December 2020)
Order no.: User's manual
Translation of the original documentation
B&R reserves the right to make changes to the content without prior notice. B&R assumes no liability for typographical errors or for any other information in this document as far as legally possible. Liability claims against B&R
regarding the content of delivery and documentation of third-party components used in the product are excluded
in any case. The user is responsible for compliance with all relevant and professionally pertinent safety measures
as well as the intended use. B&R points out that the software and hardware designations and brand names of the
respective companies are subject to the legal protection regulations of intellectual property law.
ETAL100.0610-1 user's manual V1.00 1
Table of contents
Chapter 1 Introduction.................................................................................................3
1 Manual history....................................................................................................................................................3
2 Organization of notices...................................................................................................................................... 3
Chapter 2 Intended use............................................................................................... 4
Chapter 3 Safety notices............................................................................................. 5
1 Safety notices.....................................................................................................................................................5
2 Usage................................................................................................................................................................. 5
3 Responsibilities of the operator......................................................................................................................... 5
Chapter 4 System characteristics.............................................................................. 6
1 General information............................................................................................................................................6
2 Order data..........................................................................................................................................................6
Chapter 5 Technical data............................................................................................ 7
Chapter 6 Dimensions................................................................................................. 8
1 Compatibility....................................................................................................................................................... 8
2 Installing with retaining clips.............................................................................................................................. 9
Chapter 7 Environmentally friendly disposal.......................................................... 11
1 Separation of materials.................................................................................................................................... 11
2 ETAL100.0610-1 user's manual V1.00
Introduction • Organization of notices
Chapter 1 • Introduction
1 Manual history
Version Date Change
0.10 May 2019 First internal version
1.1 INFOBOX: Current user's manual
Information:
B&R makes every effort to keep documents as current possible. The most current versions can be
downloaded from the B&R website (www.br-automation.com).
2 Organization of notices
Safety guidelines
Chapter 1
Introduction
Contain only information that warns of dangerous functions or situations.
Signal word Description
Danger! Failure to observe these safety guidelines and notices will result in death, severe injury or substantial damage to property.
Warning! Failure to observe these safety guidelines and notices can result in death, severe injury or substantial damage to property.
Caution! Failure to observe these safety guidelines and notices can result in minor injury or damage to property.
Notice! Failure to observe these safety guidelines and notices can result in damage to property.
Contain useful information for users and instructions for avoiding malfunctions.
Signal word Description
Information: Useful information, application tips and instructions for avoiding malfunctions.
European dimension standards apply to all dimension diagrams.
All dimensions in millimeters.
Unless otherwise specified, the following general tolerances apply:
Nominal dimension range General tolerance per
Up to 6 mm ±0.1 mm
Over 6 to 30 mm ±0.2 mm
Over 30 to 120 mm ±0.3 mm
Over 120 to 400 mm ±0.5 mm
Over 400 to 1000 mm ±0.8 mm
DIN ISO 2768 medium
ETAL100.0610-1 user's manual V1.00 3
Intended use
Chapter 2 • Intended use
These products are developed and produced exclusively for training and development in the area of automation.
Any use beyond this is not permitted, in particular the integration of these products or parts thereof in machines,
systems or other devices and processes. B&R does not assume liability for damages of any kind that occur when
using the products outside of training and development or for harm that results from modifying the products. Expansions using products from the ETA system or ETA light system series are permitted.
In addition, the products are only permitted to be used in closed rooms (such as laboratories, offices and classrooms) that do not require separate protective equipment. Trainers shall inform the trainees of the relevant safety
guidelines and precautions before using the product.
4 ETAL100.0610-1 user's manual V1.00
Safety notices • Responsibilities of the operator
Chapter 3 • Safety notices
1 Safety notices
Warning!
Observe safety notices
Disregarding safety notices can result in serious damage to property and personal injury.
The safety notices on the product and in the documentation must be observed.
Products that cannot be ensured as safe due to damage, for example, are not permitted to be started
up under any circumstance. Disturbances that impair general safety must be eliminated immediately.
2 Usage
This product is designed and manufactured for training and development. General safety guidelines must be observed at all times.
Chapter 3
Safety notices
Caution!
Risk of injury
Disregarding safety notices can result in serious damage to property and personal injury.
The data sheets of components and the safety notices contained therein must be observed.
For a list of the components used, see the technical data of this product.
3 Responsibilities of the operator
The operator is the person who operates the product or who provides it for use/application by a 3rd party while
carrying legal product responsibility for the protection of the user, personnel or other 3rd parties.
•
The operator is obliged to know and implement the applicable industrial safety regulations.
•
The operator is obliged to know and implement national, local and plant-specific regulations.
•
The operator is obliged to clearly define and manage responsibilities for installation, operation, fault correction, maintenance and cleaning.
•
The operator is obliged to ensure that responsible personnel have read and understood this user's manual.
ETAL100.0610-1 user's manual V1.00 5
System characteristics • Order data
Chapter 4 • System characteristics
1 General information
ETAL100.0610-1 - T50-Series module rack 10 inch
•
Module rack without hardware
•
Installing a T50-Series panel
•
Cutout dimensions: 257 mm x 176 mm
2 Order data
Model number Short description Figure
ETAL100.0610-1 T50-Series module rack panel 10 inch dimensions of installa-
Accessories
tion cutout 257 x 176 mm Suitable for: 6PPT50.101E-xxx Please
check the installation dimensions of the device.
Table 1: ETAL100.0610-1 - Order data
6 ETAL100.0610-1 user's manual V1.00
Chapter 5 • Technical data
Model number ETAL100.0610-1
Mechanical properties
Dimensions
Width 300 mm
Height 230 mm
Depth 6 mm
Installation Dimensions of the installation cutout 257 x 176 mm
Can be used for:
4PPC50.101E-xxx 6PPT50.101E-xxx
Please check the installation dimensions of the device.
Table 2: ETAL100.0610-1 - Technical data
Technical data
Chapter 5
Technical data
ETAL100.0610-1 user's manual V1.00 7
Dimensions • Compatibility
Chapter 6 • Dimensions
Information:
Check whether the installation dimensions of the desired product fit. For additional information, see
the data sheet of the product used.
1 Compatibility
This product is compatible with components from the following product groups.
•
6PPT50.101E-xxx
8 ETAL100.0610-1 user's manual V1.00
Dimensions • Installing with retaining clips
2 Installing with retaining clips
The retaining clips are designed for a certain thickness of the material
to be clamped (max. 6 mm, min. 2 mm).
A large flat-blade screwdriver is needed to tighten and loosen the screw.
The device must be installed on a flat, clean and burr-free surface since
tightening screws on an uneven area can result in damage to the display
or the ingress of dust and water.
See also "Installation cutout requirements" on page .
Figure: Retaining clips (symbolic)
Procedure
1. Insert the device into the front of the prepared, burr-free and flat installation cutout. For the dimensions of the
installation cutout, see section "Dimensions" for the individual devices.
2. Install the retaining clips on the device. To do this, insert the clips into the openings on the sides of the device
(indicated by the orange circles). The number of openings may vary depending on the size of the device.
3. Slide the retaining clips all the way to the back of the openings.
Figure: Sliding the retaining clips back
ETAL100.0610-1 user's manual V1.00 9
Chapter 6
Dimensions
Dimensions • Installing with retaining clips
4. Secure the retaining clips to the wall or control cabinet panel by tightening the mounting screws with a flatblade screwdriver.
Tightening torque: 0.4 Nm
Figure: Securing the retaining clips
10 ETAL100.0610-1 user's manual V1.00
Environmentally friendly disposal • Separation of materials
Chapter 7 • Environmentally friendly disposal
All programmable logic controllers, operating and monitoring devices and uninterruptible power supplies from B&R
are designed to have as little impact on the environment as possible.
1 Separation of materials
To ensure that devices can be recycled in an environmentally friendly manner, it is necessary to separate out the
different materials.
Component Disposal
Programmable logic controllers
Operating and monitoring devices
Uninterruptible power supplies
Batteries and rechargeable batteries
Cables
Paper/Cardboard packaging Paper/Cardboard recycling
Plastic packaging material Plastic recycling
Disposal must be carried out in accordance with applicable legal regulations.
Electronics recycling
ETAL100.0610-1 user's manual V1.00 11
Chapter 7
friendly disposal
Environmentally
Publishing information
Publishing information
B&R Industrial Automation GmbH
B&R Strasse 1
5142 Eggelsberg
Austria
Telephone: +43 7748 6586-0
Fax: +43 7748 6586-26
office@br-automation.com
12 ETAL100.0610-1 user's manual V1.00
Loading...