BOXLIGHT MP-57i, MP-58i User Manual

Download

Page 1

Projector

MP-57i / MP-58i

User's Manual - Operating Guide

Thank you for purchasing this projector!

1.800.762.5757

www.boxlight.com

Page 2

Projector

MP-57i / MP-58i

User's Manual - Operating Guide

Thank you for purchasing this projector!

Before using, read the “User’s Manual - Safety Guide” and

WARNING!

these manuals to ensure correct usage through understanding. After reading, store them in a safe place for future reference

NOTE: The information in this manual is subject to change without notice. The manufacturer assumes no responsibility for any errors that may appear in this manual. The reproduction, transmission or use of this document or contents is not permitted without express written authority.

TRADEMARK ACKNOWLEDGMENT

• VGA and XGA are registered trademarks of the International Business Machines Corporation.

• Apple and Mac are registered trademarks of Apple Computer, Inc.

• VESA and SVGA are trademarks of the Video Electronics Standard Association.

• Windows is a registered trademark of Microsoft Corporation.

• Internet Explorer is a trademark of the Microsoft Corporation.

All other trademarks are the property of their respective owners.

Page 3

Projector Features

This multimedia projector is used to project various computer signals as well as NTSC/PAL/SECAM video signals onto a screen. Little space is required for installation and large images can easily be realized.

Ultra High Brightness

●

Crisp, ultra-bright presentations is achieved by using a UHB (ultra high brightness) lamp and a highly efficient optical system.

Whisper Mode Equipped

●

Special mode is available for reducing projector noise to achieve quieter operation.

User Memory Function

●

This projector can memorize 4 settings by MY MEMORY function.

Partial Magnification Function

●

Interesting parts of images can be magnified for closer viewing.

Keystone Distortion Correction

●

Quick correction of distorted images electrically.

Optical Lens Shift

●

The lens of this projector can be shifted vertically. When you want to finely adjust the picture position, use the LENS SHIFT buttons.

Preparation

Please see the “Contents Of Package” of the “User’s Manual – Quick Guide”. Your projector should come with the items shown there. Contact your dealer anything is missing.

NOTE

sure to use the original packing material. Use special caution for the lens part.

• Keep the original packing material for future reshipment. For moving the projector, be

Page 4

Contents

Projector Features Preparation Part Names

Projector ……………………………4 Control Buttons ……………………5 Remote control ……………………5

Setting Up

Arrangement ………………………6 Adjusting The Projector’s Elevator ……………………………7 Using The Lens shift Buttons ……7 Connecting Your Devices…………8 Connecting The Power Supply …11

Remote Control

About The Laser Pointer ………12 Putting Batteries …………………12 Operating The Remote Control …………………13 Using The Remote ID Feature…………………………13 Using The Mouse/Keyboard Control Function …………………14

Power ON/OFF

Turning On The Power …………15 Turning Off The Power …………15

Operating

Selecting An Input Signal ………16 Selecting The Aspect Ratio ……17 Using The Automatic Adjustment Feature………………17 Adjusting The Picture Position …18 Correcting The Keystone Distortion …………………………18 Adjusting The Volume …………19 Muting The Sound ………………19 Temporarily Blanking The Screen ………………………19 Freezing The Screen ……………20 Using The Magnify Feature ……20 Displaying The Child Window …21 Selecting An Audio Input ………21

…………………………………………………… ……………………………………………………

…………………………………………………………

……………………………………………………

……………………………………

…………………………………………

Multifunctional Settings 2 4

Using The Menu Functions ……22 MAIN Menu ………………………23 PICTURE-1 Menu ………………24 PICTURE-2 Menu ………………26 INPUT Menu ……………………27 AUTO Menu ………………………29 SCREEN Menu …………………31 OPTION Menu ……………………33 NETWORK Menu ………………35

Network Setting Up

Lamp

Air Filter

Other Care

Troubleshooting

Warranty And After-Service

Specifications

TECHNICAL

………………………………………………………………

Replacing The Lamp ……………38

…………………………………………………………

Caring For The Air Filter…………39

……………………………………………………

Caring For The Inside Of The Projector ……………………40 Caring For The Lens ……………40 Caring For The Cabinet And Remote Control …………………40

Related Messages ………………41 Regarding The Indicator Lamps ……………………………43 Phenomena That May Easily Be Mistaken For Machine Defects …45

……………………

………………………………

……………………………………

…………

…………………………………………

36 37

47 47

Page 5

Part Names

Projector

Projector (Front/Right)

REMOTE CONTROL

RGB

AUDIO O

RGB OUT

G/Y

B/C

BNC

CR/PR

R-AUDIO IN-L

Projector (Rear/Left)

D E

AUDIO I

R/C

Ca/Pa

LENS SHIF

VIDEO

CONTROL

LAMP

TEMP

NDBY/ON

STA

VID

MEN

S-VID

TER

FOCUS

SET

R SEARCH

COMPON

BNG

PUT

IFT

RGB

M1-D

EYS

1 Elevator button 2 Elevator foot

3 Remote sensor 4 Lens cap 5 Lens

The picture is projected from here.

6 Filter cover

An air filter is inside.

A RGB port

EYSTONE

-D

SEAR

INP

BNG

MPON

RESET

S-VID

LAMP

FOCUS

ZOOM

MEN

STANDBY/ON

S-VIDEO

NETWORK

B M1-D port C BNC port D AUDIO IN 1 port E AUDIO IN 2 port F CONTROL port G NETWORK port H AUDIO IN R/L port I VIDEO IN port J S-VIDEO port K COMPONENT port L RGB OUT port M AUDIO OUT port

7 REMOTE CONTROL port 8 DC OUT port 9 AC Inlet 0 Power switch

- Control buttons

See the following page.

Page 6

Part Names (continued)

ENTER

INPUT

M1-D

RGB

BNC

S-VIDEO

STANDBY/ON

TEMP

VIDEO

COMPONENT

LAMP

KEYSTONE

RESET

FOCUS

LENS SHIFT

ZOOM

w q

Part Names (continued)

Control Buttons

MP E

O /

ANDBY T

VIDEO

N E M

DEO I

S-

E T

FOCUS

E E R

ON P

IN H C

SHI

SEA

-D 1

N O

T S

KEY

Control Panel on the Projector

Remote Control

1 STANDBY/ON button

and STANDBY/ON indicator

2 TEMP indicator 3 LAMP indicator 4 LENS SHIFT buttons 5 INPUT dial 6 SEARCH button 7 M1-D indicator 8 RGB indicator 9 BNC indicator 0 COMPONENT indicator

- S-VIDEO indicator = VIDEO indicator q ZOOM buttons w FOCUS buttons e KEYSTONE button r MENU button t RESET button y ENTER button u Cursor buttons / / /

1 STANDBY/ON button

4 LENS SHIFT buttons

6 SEARCH button

q ZOOM buttons w FOCUS buttons e KEYSTONE button r MENU button t RESET button y ENTER button

( Mouse left button)

u Cursor buttons

/// ( Keyboard Arrow keys / / / )

(Rear)

STANDBY/ON

LENS SHIFT

–––

BLANK

ESC MENU

POSITION

MAGNFY

OFF

Remote Control

LASER INDICATOR

VIDEO

FOCUS ZOOM

ASPECT

ENTER

RESET AUTO

PinP

FREEZE MUTE

KEYSTONE

1 2 3

ID CHANGE

RGB

LASER

VOLUME

[ \

]

a d

g l

;

i LASER INDICATOR o VIDEO button p RGB button [ BLANK button ] ASPECT button \ LASER button a Cursor buttons / / /

( Mouse move pointer)

s ESC button

( Keyboard ESC key)

d ( Mouse right button) f POSITION button g AUTO button h PinP button j MAGNIFY buttons k FREEZE button l VOLUME button ; MUTE button ' ID CHANGE switch

Page 7

Setting Up

Arrangement

WARNING • Before installation, make sure that the projector is turned off and the power code is disconnected.

• Do not set up and move the projector, while it is hot.

• Install the projector in a suitable environment according to instructions of the “User’s Manual – Safety Guide” and this manual.

• The power outlet should be close to the projector and easily accessible.

Refer to the illustrations and tables below to determine the screen size and projection distance. The values shown in the table are calculated for a full size screen. (±10%)

Reference for the 4:3 aspect ratio

Screen

Lens center

Side View

Reference for the 16:9 aspect ratio

Screen

Lens center

Side View

Screen Size

[inch (m)]

40 (1.0) 46(1.2) 71(1.8) 12(30) 24(61) 60 (1.5) 71(1.8) 107(2.7) 18(46) 36(91) 70 (1.8) 83(2.1) 126(3.2) 21(53) 42(107)

80 (2.0) 95(2.4) 144(3.7) 24(61) 48(122) 100 (2.5) 120(3.0) 181(4.6) 30(76) 60(152) 120 (3.0) 144(3.7) 217(5.5) 36(91) 72(183) 150 (3.8) 181(4.6) 272(6.9) 45(114) 90(229) 200 (5.1) 243(6.2) 364(9.2) 60(152) 120(305) 250 (6.4) 304(7.7) 300 (7.6) 366(9.3) 350 (8.9)

400 (10.2) 500 (12.7)

Screen Size

[inch (m)]

40 (1.0) 50(1.3) 77(2.0) 10(25) 23(58)

60 (1.5) 77(2.0) 117(3.0) 15(37) 34(87)

70 (1.8) 91(2.3) 137(3.5) 17(44) 40(102)

80 (2.0) 104(2.6) 157(4.0) 20(50) 46(116) 100 (2.5) 131(3.3) 197(5.0) 25(62) 57(145) 120 (3.0) 158(4.0) 237(6.0) 29(75) 69(174) 150 (3.8) 198(5.0) 297(7.5) 37(93) 86(218) 200 (5.1) 265(6.7) 250 (6.4) 332(8.4) 300 (7.6) 350 (8.9)

400 (10.2) 450 (11.4)

a [inch (m)] b [inch (cm)]

Min. Max.

455(11.6)

547(13.9) 427(10.9) 638(16.2) 489(12.4) 730(18.5) 612(15.5) 913(23.2)

a [inch (m)] b [inch (cm)]

Min. Max.

396(10.1)

496(12.6) 399(10.1) 596(15.1) 466(11.8) 696(17.7) 533(13.5) 795(20.2) 600(15.2) 895(22.7)

m:n=1:1 m:n=10:0

75(191) 150(381)

90(229) 180(457) 105(267)210(533) 120(305)240(610) 150(381)300(762)

m:n=1:1 m:n=10:0

49(125) 114(291)

61(156) 143(363)

74(187) 172(436)

86(218) 200(508)

98(249) 229(581) 110(280)257(654)

Page 8

-D

BNG

S-

DBY

RCH

Setting Up (continued)

10:0

1:1

STANDBY/ON

VIDEO

LASER INDICATOR

RGB

BLANK ASPECT LASER

LENS SHIFT

–––

FOCUS ZOOM

LENS SHIFT

Setting Up (continued)

Adjusting The Projector's Elevator

WARNING • Do not touch about the lens and ventilation openings during use or immediately after use to prevent a burn.

CAUTION

hold the projector whenever using the elevator buttons to adjust the elevator feet.

You can use the elevator feet to make adjustments if the surface on which you need to set the projector is uneven or if you otherwise need to adjust the angle of projection. The adjustment range of the elevator feet is 0 to 9 degrees.

• To prevent damaging the projector and injuring yourself, always

Press and hold in the elevator buttons.

Raise or lower the projector to the desired height and

then release the elevator buttons. When you release the elevator buttons, the elevator feet will lock into position.

As necessary, you can also finely adjust the height of

the projector by twisting the elevator feet by hand.

Using The Lens Shift Buttons

NOTE

to the center.

The lens of this projector can be shifted vertically. When you want to finely adjust the picture position, use the LENS SHIFT buttons of the projector.

• Generally, better quality of a picture is available when the lens shift is set

Elevator buttons

Elevator feet

Projector

LENS SHIFT buttons

Remote control

Page 9

Setting Up (continued)

Connecting Your Devices

WARNING • Whenever attempting to connect other devices to the projector, read thoroughly the "User's Manual - Safety Guide", this manual and the manual of each

device to be connected. Incorrect connecting could result in fire or electrical shock.

CAUTION

Attempting to connect a live device to the projector may generate extremely loud noises or other abnormalities that may result in malfunction and/or damage to the device and/or projector.

ATTENTION

connection may result in malfunction and/or damage to the device and/or projector. Refer to the section “Technical” of this manual for the pin assignment of connectors and RS-232C communication data.

• Some cables have to be used with core set. Use the accessory cable or a

designated-type cable for the connection. For cables that have a core only at one end, connect the core to the projector.

• Secure the screws on the connectors and tighten.

• Whenever attempting to connect a laptop computer to the projector, be sure to

activate the laptop’s RGB external image output (set the laptop to CRT display or to simultaneous LCD and CRT display). For details on how this is done, please refer to the instruction manual of the corresponding laptop computer.

• TURN OFF ALL DEVICES prior to connecting them to the projector.

• Make sure that you connect devices to the correct port. Incorrect

NOTE

these modes may not be compatible with this projector.

• For some RGB input modes, the optional Mac adapter is necessary.

• When the image resolution is changed on a computer, depending on an input,

automatic adjust function may take some time and may not be completed. In this case, you may not be able to see a check box to select “Yes/No” for the new resolution on Windows. Then the resolution will go back to the original. It might be recommended to use other CRT or TFT monitors to change the resolution.

NOTE

• Plug-and-Play is a system incorporated in the computer, its operating system and

peripheral equipment (i.e. display devices).

• This projector is compatible with VESA DDC 1/2B. Plug-and-Play can be achieved by

connecting this projector to computers that are VESA DDC (display data channel) compatible.

• Please take advantage of this function by connecting the accessory RGB cable to the

RGB port (DDC 1/2B compatible). Plug-and-Play may not work properly if any other type of connection is attempted.

• Please use the standard drivers in your computer as this projector is a Plug-and-Play

monitor.

• Some computers may have multiple display screen modes. Use of some of

Plug-and-Play Capability

Page 10

Setting Up (continued)

R/CR/PR G/Y B/CB/PB H V

VIDEOR-AUDIO IN-L

S-VIDEO

BNC

RGB

AUDIO IN1

AUDIO IN2

RGB OUT

AUDIO OUT

REMOTE CONTROL

R/C

R/PR G/Y B/CB/PB HV

CONTROL

NETWORK

CR/PR

Ca/Pa

F G

REMOTE CONTROL

VIDEOR-AUDIO IN-L

S-VIDEO

BNC

RGB

AUDIO IN1

AUDIO IN2

RGB OUT

AUDIO OUT

G/Y H V

CONTROL

NETWORK

CR/PR

Ca/Pa

R/CR/PR B/CB/PB

REMOTE CONTROL

VIDEOR-AUDIO IN-L

S-VIDEO

BNC

RGB

AUDIO IN1

AUDIO IN2

RGB OUT

AUDIO OUT

R/C

R/PR G/Y B/CB/PB HV

CONTROL

NETWORK

CR/PR

Ca/Pa

Setting Up (continued)

Please refer to the following (for example) for connecting your devices. See the rear of the projector. You can see the ports.

Examples of connection with a computer

Y S

T ON

E L E

I F

N P

ARC U T

BNG C O

O NE

RE S

E T

E R

O E O

C U

Z O

O M

VID

U S T A

N D

/ ON

T EM

LAM

U D

I O

I N1

D IO

I N2

RGB

RGB OUT

R/C

G/Y

B/C

BNC

REMO

ONTROL

CONTROL

NETWORK

A U

D IO

CR/

Ca /Pa

A U

D IO

I N

E O

-V ID

E O

Computer Projector

RGB out RGB cable RGB

Audio out Stereo Mini cable AUDIO IN 2

RS-232C port RS-232C cable CONTROL

Network port CAT-5 cable NETWORK

■ If using a M1-D input (to mouse control)

DVI port M1-D

USB port M1-D cable

Audio out Stereo Mini cable AUDIO IN 1

■ If using a BNC input

R/PR

R/C G/Y B/CB/PB

RGB out

BNC cable

H V

Audio out Stereo Mini cable AUDIO IN 1

Page 11

Setting Up (continued)

VIDEOR-AUDIO IN-L

S-VIDEO

BNC

RGB

AUDIO IN1

AUDIO IN2

RGB OUT

AUDIO OUT

R/C

R/PR G/Y B/CB/PB HV

CONTROL

NETWORK

CR/PR

Ca/Pa

REMOTE CONTROL

H I

REMOTE CONTROL

VIDEOR-AUDIO IN-L

S-VIDEO

BNC

RGB

AUDIO IN1

AUDIO IN2

RGB OUT

AUDIO OUT

R/C

R/PR G/Y B/CB/PB HV

CONTROL

NETWORK

CR/PR

Ca/Pa

H J

REMOTE CONTROL

VIDEOR-AUDIO IN-L

S-VIDEO

BNC

RGB

AUDIO IN1

AUDIO IN2

RGB OUT

AUDIO OUT

R/C

R/PR G/Y B/CB/PB HV

CONTROL

NETWORK

CR/PR

Ca/Pa

R-AUDIO IN-L VIDEO

COMPONENT

R-AUDIO IN-L VIDEO

REMOTE CONTROL

VIDEOR-AUDIO IN-L

S-VIDEO

BNC

RGB

AUDIO IN1

AUDIO IN2

RGB OUT

AUDIO OUT

R/C

R/PR G/Y B/CB/PB HV

CONTROL

NETWORK

CR/PR

Ca/Pa

Setting Up (continued)

Examples of connection with a VCR/DVD Player

VCR/DVD Player Projector

Audio out (R)

Audio out (L)

Video out

R-AUDIO IN AUDIO IN-L VIDEO IN

■ If using a s-video signal

S-video out S-video cable S -VIDEO

Audio out (R)

Audio out (L)

R-AUDIO IN AUDIO IN-L

■ If using a component signal

CR/PR out CB/PB out

Y out

Audio out (R)

Audio out (L)

CR/PR CB/PB Y

R-AUDIO IN AUDIO IN-L

■ If using a SCART RGB input

H I

SCART RGB out

SCART adapter

COMPONENT

R-AUDIO IN-L VIDEO

R (CR/PR) B (C

B/PB)

G (Y) R-AUDIO IN AUDIO IN-L VIDEO IN

H I

Page 12

Setting Up (continued)

REMOTE CONTROL

VIDEOR-AUDIO IN-L

S-VIDEO

BNC

RGB

AUDIO IN1

AUDIO IN2

RGB OUT

AUDIO OUT

R/C

R/PR G/Y B/CB/PB HV

CONTROL

NETWORK

CR/PR

Ca/Pa

REMOTE CONTROL

VIDEOR-AUDIO IN-L

S-VIDEO

BNC

RGB

AUDIO IN1

AUDIO IN2

RGB OUT

AUDIO OUT

R/C

R/PR G/Y B/CB/PB HV

CONTROL

NETWORK

CR/PR

Ca/Pa

Setting Up (continued)

Connecting to a monitor

Monitor Projector

RGB in RGB cable RGB OUT

Connecting to a speaker (with amplifier)

Speaker Projector

Audio in Stereo Mini cable AUDIO OUT

Connecting The Power Supply

WARNING • connections may result in fire and/or electrical shock. Please adhere to the “User’s manual –

Safety Guide” and the following.

•

Only plug the power cord into outlets rated for use with the power cord’s specified voltage range.

•

Only use the power cord that came with the projector. If it is damaged, contact your dealer to newly get correct one.

•

Never modify the power cord. Never attempt to defeat the ground connection of the three-pronged plug.

•

Make sure that you firmly connect the power cord to the projector and wall outlet.

Connect the connector of the power cord to

the AC inlet of the projector.

Firmly plug the power cord’s plug into the

outlet.

Use extra caution when connecting the power cord as incorrect or faulty

KEYST

O N

E L E

S SHIF

1-D

SEARC I N

P U

COM

ONENT

I N

S-VID

E R

OC E O

O O

A U DIO IN1

A U

D IO

I N2

R/C

REMOTE CONTROL

CONTROL

RGB

UDIO OUT

RGB OUT

CR/PR

Ca/Pa

G/Y

B/C

-A U

I N

-L VID

BNC

AC Inlet

Connector Plug

M E O

N U

TAN

DBY

/ O

TEM

LAMP

NETWORK

S-VIDE

Outlet

Page 13

Remote Control

STANDBY/ON

VIDEO

LASER

INDICATOR

ESC MENU

POSITION

RESET AUTO

KEYSTONE

1 2 3

ID CHANGE

OFF

FREEZE MUTE

MAGNFY

PinP

VOLUME

RGB

BLANK

ASPECT

ENTER

LASER

LENS SHIFT

–––

FOCUS ZOOM

JQA

MADE IN CHINA

P S

レーザー光をのぞき込まないこと。レーザー光を人に向けないこと。子供に使わせないこと。製造者：INTERLINK ELECTRONICS

AVOID EXPOSURE-LASER

RADIATION IS EMITTED FROM THIS APERTURE

CAUTION

WAVE LENGTH: 640-660nm MAX OUTPUT: 1mW CLASS 2 LASER PRODUCT

Comples with 21 CFR, 1040.10 AND 1040.11 IEO60825-1:1993+A1:1997+A2:2001

LASER-STRAHLING NICHT IN DEN STRAHL BLICKEN LASER KLASSE 2 WAVE LENGTH:640-660nm MAX OUTPUT:1mW

レーザー光ビームをのぞきこまないことクラス2レーザー製品 JISC6802（1998）最大出力：1.0mW 波長：640−660nm

MODEL:H-IRC4

LASER RADIATION

DO NOT STARE INTO BEAM

MANUFACTURER: B MANUFACTURED

JANUARY,2003 INTERLINK K.K. 1-10-7 HIGASHIKANDA CHIYODA-KU,TOKYO,JAPAN 101-0031

MADE IN CHINA

Remote Control

About The Laser Pointer

WARNING • The laser pointer of the remote control is used in place of a finger or rod. Never look directly into the laser beam outlet or point the laser beam at other

people. The laser beam can cause vision problems.

CAUTION

• Use of controls or adjustments or performance of procedures other

than those specified herein may result in hazardous radiation exposure.

This remote control has a laser pointer in place of a finger or rod. The laser beam works and the LASER INDICATOR lights while the LASER button is pressed.

Putting Batteries

CAUTION • About the battery

• Keep a battery away from children and pets.

• Use only the battery specified: two AA batteries.

• Do not mix new battery with used one.

• Make sure the plus and minus terminals are correctly aligned when loading the battery (as indicated in the remote control).

• Dispose of batteries in accord with environmental laws.

Remove the battery cover. Slide back and remove the battery cover in the direction of the arrow.

Insert the batteries.

Align and insert the two AA batteries according to their plus minus terminals (as indicated in the remote control).

Close the battery

cover. Replace the battery cover in the direction of the arrow and snap it back into place.

Page 14

Remote Control (continued)

INT

I NPUT

D R G

B B N

V ID

E O

T A N

D B

Y / O

ID E

M P O

N E N

L A

M P

E Y

S T O

N E S E

A R

H R E

S E

E N U

F O C

U S

L E

N S

S H

I F T

Z O O

I D

E O

A U

D I O I N

-L S

V I D

O B N

R G

U D I O

I N 1

U D I

O I N

R G

B O

U T

A U D

I O

O U

R E M

O T

E C

O N

T R O

R /

/ P

G /Y

/ C

/ P

C O

T R O

E T W

O R

C R

/ P R

C a /

P a

approximately 3 meters

30 degrees

approximately 3 meters

20 degrees

Remote Control (continued)

Operating The Remote Control

CAUTION • Do not disassemble the remote control.

• Do not place the remote control near the projector’s lens, fan, or vents.

• Do not drop or otherwise expose the remote control to physical impact.

•

Do not get the remote control wet or place it on wet objects on it. Doing so may result in malfunction.

• Remove the batteries from the remote control and store them in a safe place if you won't be using the remote control for an extended period.

NOTE

•

When strong light, such as direct sunlight or light from an extremely close range (such as from an

• Replace the batteries whenever the remote control starts to malfunction.

inverter fluorescent lamp), hits the projector's remote sensor, the remote control may cease to function. Adjust the direction of the projector to keep light from directly hitting the projector's remote sensor.

•

The remote control works with the projector’s remote sensor.

•

Front remote sensor is 3 meters with a 60 degree range (30 degrees to the left and right of a remote sensor). Rear remote sensor is 3 meters with a 40 degree range (20 degrees to the left and right of a remote sensor).

•

Also a remote signal reflected in the screen etc. may be available. If it is difficult to send a remote signal to the sensor directly, please try.

•

Since the remote control uses infrared light to send signals to the projector (Class1 LED), be sure to use the remote control in an area free from obstacles that could block the remote control’s output signal to the projector.

memo

You can use the remote control as a wired remote control, by connecting the REMOTE CONTROL

ports of the main unit and remote control via an audio cable (3.5 dia. stereo mini cable with plugs).

Using The Remote ID Feature

This is the function to properly use when you use two or three same type projectors at the same time. This function should be used combining a setup of a projector.

Set the ID number to the projector beforehand,

referring to the item “IR REMOTE ID” of the section “OPTION Menu”.

memo

When the ALL is selected to the item “IR REMOTE ID” of the OPTION menu, the projector is controlled by a remote control irrespective of the position of the ID CHAGE switch.

Slide the knob of the switch into the position of the ID number of the projector you want to control.

LASER INDICATOR

STANDBY/ON

VIDEO

LENS SHIFT

FOCUS ZOOM

–––

ASPECT

BLANK

ENTER

ESC MENU

POSITION

RESET AUTO

MAGNFY

PinP

FREEZE MUTE

OFF

KEYSTONE

1 2 3

ID CHANGE

RGB

LASER

ID CHANGE switch

VOLUME

Page 15

Remote Control (continued)

Using The Mouse/Keyboard Control Function

CAUTION • Before connecting, read the manuals of the device you will connect.

Mistaken use of the mouse/keyboard control could damage your equipment.

• Only connect to a PC.

• Do not unplug the connector cables while the computer is operating.

Using the USB control feature, you can use the remote control as a simplified mouse or keyboard of the computer.

Connect the M1-D port of the projector to the computer via the M1-D cable. Then functions illustrated below will be enabled.

memo

The USB control can be used with Windows 95 OSR 2.1 or higher. It may not be possible to use the remote control, depending on the computer’s configurations and mouse drivers.

memo

The function can be used only for the

functions illustrated on the right.

memo

The projector would be enumerated as a mouse and a keyboard of HID (Human Interface Device) class devices, after connecting cable.

LASER INDICATOR

STANDBY/ON

VIDEO

LENS SHIFT

FOCUS ZOOM

–––

ASPECT

BLANK

ENTER

ESC MENU

POSITION

RESET AUTO

MAGNFY

PinP

FREEZE MUTE

OFF

KEYSTONE

1 2 3

ID CHANGE

RGB

LASER

Arrow keys / / /

VOLUME

Mouse right button

Keyboard ESC key

Mouse left button

Mouse move pointer

Keyboard

(Front)

(Rear)

Page 16

STANDBY/ON

VIDEO

LASER INDICATOR

RGB

LENS SHIFT

–––

FOCUS ZOOM

I N T E R

I NP U T

1-D R GB

B N G

-V I D E O

S T A

N D

BY / O

N T

E M P

V ID

O M

P O N

E N T

A M P

K E Y

O N E S E A

R C

H R E S

E N

OCUS

LE N S

S H

I FT

Z O O

V I D E

U D IO

I N

S-

V I D E

BNC

R G B

A U D

I O I N

A U

D I O I N

R GB O

A U

D I

O O

U T

REM

CON

T R

R/C

/ P

G/Y

B / C

/ P

C ONT

ROL

NETWOR

CR/PR

a/Pa

I N T E R

I N P U T

-D R GB

B N G

I D E O

ST A

N D

B Y / O

N T

E M P

V I

D E

O M

P O N

E N T

A M P

K E YST

O N E S E A

R C

H R E SE

E N

O CU

N S

S H

I F T

Z O OM

I D E

U D I O

I N

S-V

ID E

BNC

RGB

A U D

I O I N

A U

D IO I N2

R GB O

A U

D IO

U T

REMOTE

CON

T R

R /C

/ P

G/Y

B/ C

/ P

N TROL

ET WOR

CR/

Ca/Pa

STANDBY/ON

VIDEO

LASER INDICATOR

RGB

LENS SHIFT

–––

FOCUS ZOOM

IN T E R

I N P U T

D R GB

BNG

-V I D E O

S T A

NDB

Y/ ON

E M P

V ID

O M

P O N

E N T

A MP

KEY

S T

ONE SE A

R C H

RES

E T

E N

O C

N S S

IF T

ZO O

V I D E

U D I O

I N

V I D E

BNC

RG B

A U D

I O I N

A U

D I O I N

R G B

O U

A U

D I

O O

U T

R E

M O

C ON

T R

O L

R /C

/ P

/ Y

B / C

/ P

N TR

ET W

O RK

CR/

R C

a /Pa

Power ON/OFF

LENS SHIFT

STANDBY/ON

VIDEO

LASER INDICATOR

RGB

BLANK ASPECT LASER

LENS SHIFT

–––

FOCUS ZOOM

Power ON/OFF

WARNING • When the power is ON, a strong light is emitted. Do not look

into the lens or vents of the projector.

NOTE

• Turn the power on/off in right order. Please power on the projector before

the connected devices. Power off the projector after the connected devices.

Tur ning On The Power

STANDBY/ON

Remove the lens cap.

Set the power switch to [ | ] (ON).

The STANDBY/ON indicator will light to solid orange.

STANDBY/ON button / indicator

STANDBY/ON

Press the STANDBY/ON button.

The projector lamp will light up and the STANDBY/ON indicator will begin blinking green.

Power switch (ON position)

When the power is completely on, the indicator will stop blinking and light green.

Use the LENS SHIFT buttons to shift the

picture upward or downward.

LENS SHIFT

Select an input signal according to the

section “Selecting An Input Signal” of the

buttons

following page.

Tur ning Off The Power

STANDBY/ON

button

Press the STANDBY/ON button.

The message “Power off?” will appear on the screen for approximately 5 seconds.

STANDBY/ON

STANDBY/ON button / indicator

Press the STANDBY/ON button again while

“Power off?” the message is visible. The projector lamp will go off, and the STANDBY/ON indicator will begin blanking orange. Then the STANDBY/ON indicator will stop blinking and light to solid orange when the lamp cooling is complete.

Switch the power switch to [O] (OFF).

The STANDBY/ON indicator will go off.

Attached the lens cap.

Power switch (OFF position)

STANDBY/ON

button

Page 17

I N T E R

I N P U T

M1-D R GB

B N G

I D E O

S T A

N DB

Y / O

N T

V ID

O M

P O N

E N T

M P

K E Y

S T

O N E S EA

R C

H R E S

E N

O CU

N S

S H

I F T

Z O O

ID E

-A U D I O

I N

S-

V I D E

BNC

RGB

A U D

IO I N

A U

D I O I N

RGB O

A U

D I

O O

REMOTE

CONT

R /C

/ P

G/Y

B / C

C ONTROL

ET W

ORK

CR/PR

Ca/P

Operating

I N T E R

I N P U T

M1-D R G

B N G

-V I DEO

S T A

N DB

Y / O

N T

E M P

VIDEO

O M

P ON

E N T

M P

K E YS

O N E S EAR

CH R E SE

OCUS

LEN

S HIFT

ZO OM

V I D E

-A U D IO

I N

S-

V I D E

BNC

R G B

A U D

I O I N

A U

D I O I N

RGB

O U

A U

D I

O O

U T

R E

M OT

C O

N T R

O L

R/ C

/ P

G/Y

B / C

/ P

C O

N TR

ET W

OR K

CR/P

R C

a/ P a

ZOOM

FOCUS

Operating

Selecting An Input Signal

Select an input signal.

■ Using the INPUT dial

Turn the INPUT dial of the projector. Turning the dial cycles through the input ports as shown below. Select the signal you wish to project.

M1-D RGB BNC

VIDEO

■ Using SEARCH button

Press the SEARCH button of the projector or the remote control. Pressing the button automatically cycles through input ports and displays the picture of retrieved signal.

memo

If no signal is found or the projector is unstable to find an input signal at any of its ports, it will turn to the state it was in prior to the search.

M1-D RGB BNC

VIDEO

■ Using RGB button

Press the RGB button of the remote control. Pressing the button toggles between the RGB ports as shown below Select the signal you wish to project.

M1-D RGB BN

S-VIDEO COMPONEN

BNC

COMPONENT

S-VIDEO

INPUT dial

LASER INDICATOR

STANDBY/ON

VIDEO

LENS SHIFT

FOCUS ZOOM

–––

ASPECT

BLANK

ENTER

ESC MENU

POSITION

RESET AUTO

MAGNFY

PinP

FREEZE MUTE

OFF

KEYSTONE

1 2 3

ID CHANGE

SEARCH button

M1-D

INPUT

RGB

ENTER

VIDEO

VIDEO button

RGB

LASER

SEARCH button

VOLUME

RESET

RGB button

■ Using VIDEO button

Press the VIDEO button of the remote control. Pressing the button toggles between the VIDEO ports as shown below Select the signal you wish to project.

S-VIDEO VIDEOCOMPONENT

Use the ZOOM buttons to adjust the screen size.

Use the FOCUS buttons to adjust the focus.

ZOOM

buttons

FOCUS buttons

Page 18

Operating (continued)

Selecting The Aspect Ratio

Press the Aspect button to toggle between the

modes for aspect ratio.

■ At a M1-D signal

NORMAL

memo

NORMAL keeps the original aspect ratio of the

4:3

16:9

input signal.

■ At a RGB signal (not M1-D)

4:3

16:

■ At a video signal

4:3

memo

16:9

SMALL

At a HDTV signal of 1125i or 750p, only 16:9 can

LASER INDICATOR

STANDBY/ON

VIDEO

LENS SHIFT

FOCUS ZOOM

–––

ASPECT

BLANK

ENTER

ESC MENU

POSITION

RESET AUTO

MAGNFY

PinP

FREEZE MUTE

OFF

KEYSTONE

1 2 3

ID CHANGE

be selected.

Using The Automatic Adjustment Feature

RGB

LASER

VOLUME

ASPECT button

memo The automatic adjustment operation requires approximately 10 seconds. Also,

please note that it may not function correctly with some input.

Press the AUTO button.

■ At a RGB signal

The Vertical position (V POSITION), the horizontal position (H POSITION), the clock phase (H PHASE) and horizontal size (H SIZE) will be automatically adjusted.

memo

Make sure that the application window is set to its maximum size prior to attempting to use this feature. Dark pictures may still be incorrectly adjusted. Use a bright screen when adjusting.

■ At a video signal

The signal type mode best suited for the respective input signal will be selected automatically.

memo

This function is available only when the AUTO is selected to the item VIDEO of the INPUT menu. For a component video signal, the signal type is identified automatically independently of this function.

LASER INDICATOR

STANDBY/ON

VIDEO

LENS SHIFT

FOCUS ZOOM

–––

ASPECT

BLANK

ENTER

ESC MENU

POSITION

RESET AUTO

MAGNFY

PinP

FREEZE MUTE

OFF

KEYSTONE

1 2 3

ID CHANGE

RGB

LASER

AUTO button

VOLUME

Page 19

Operating (continued)

Adjusting The Picture Position

memo This function is available only for RGB signals.

Press the POSITION button.

As illustrated on the right, a dialog will appear on the screen to aid you in adjusting the position.

Use the cursor buttons / / / to adjust the

position.

memo

When you want to initialize the position, press

POSITION

the RESET button during adjustment.

Press the POSITION button again to close the

dialog and complete this operation.

memo

Even if you don't do anything, the dialog will

automatically disappear after a few seconds.

Correcting The Keystone Distortion

Press the KEYSTONE button.

As illustrated on the right, a dialog will appear on the screen to aid you in correcting the keystone distortion.

Use the cursor buttons / to

select the direction of distortion to correct ( or ).

Use the cursor buttons / to correct the

distortion.

Press the KEYSTONE button again to close the

dialog and complete this operation.

memo

Even if you don't do anything, the dialog will

automatically disappear after a few seconds.

memo When this adjustment is excessive, certain

degradation may appear on the picture. Also, please note that it may not function correctly with some input.

KEYSTONE

LASER INDICATOR

STANDBY/ON

VIDEO

LENS SHIFT

FOCUS ZOOM

–––

ASPECT

BLANK

ENTER

ESC MENU

POSITION

RESET AUTO

MAGNFY

PinP

FREEZE MUTE

OFF

KEYSTONE

1 2 3

ID CHANGE

LASER INDICATOR

STANDBY/ON

VIDEO

LENS SHIFT

FOCUS ZOOM

–––

ASPECT

BLANK

ENTER

ESC MENU

POSITION

RESET AUTO

MAGNFY

PinP

FREEZE MUTE

OFF

KEYSTONE

1 2 3

ID CHANGE

LASER

VOLUME

LASER

VOLUME

RGB

Cursor buttons

POSITION button

RESET button

RGB

Cursor buttons

KEYSTONE button

Page 20

Operating (continued)

Adjusting The Volume

Press the VOLUME button.

As illustrated on the right, a dialog will appear on the screen to aid you in adjusting the volume.

Use the cursor buttons / to

adjust the volume.

Press the VOLUME button again to close the

dialog and complete this operation.

memo

Even if you don't do anything, the dialog will

automatically disappear after a few seconds.

Muting The Sound

Press the MUTE button.

As illustrated on the right, a dialog will appear on the screen indicating that you have muted the sound.

Press the MUTE or VOLUME

button to restore the sound.

memo

Even if you don't do anything, the dialog will automatically disappear after a few seconds.

VOLUME

LASER INDICATOR

STANDBY/ON

VIDEO

LENS SHIFT

FOCUS ZOOM

–––

ASPECT

BLANK

ENTER

ESC MENU

POSITION

RESET AUTO

MAGNFY

PinP

FREEZE MUTE

OFF

KEYSTONE

1 2 3

ID CHANGE

LASER INDICATOR

STANDBY/ON

VIDEO

LENS SHIFT

FOCUS ZOOM

–––

ASPECT

BLANK

ENTER

ESC MENU

POSITION

RESET AUTO

MAGNFY

PinP

FREEZE MUTE

OFF

KEYSTONE

1 2 3

ID CHANGE

LASER

VOLUME

LASER

VOLUME

RGB

Cursor buttons

VOLUME button

RGB

MUTE button

Temporarily Blanking The Screen

Press the BLANK button.

The input signal screen will shut off, and a BLANK screen will appear.

memo You can set the BLANK screen using the

menu. Please refer to the item “BLANK” of the table of the section “SCREEN Menu”.

Press the BLANK button again to remove the

blank screen, and return to the input signal screen.

LASER INDICATOR

STANDBY/ON

VIDEO

LENS SHIFT

FOCUS ZOOM

–––

ASPECT

BLANK

ENTER

ESC MENU

POSITION

RESET AUTO

MAGNFY

PinP

FREEZE MUTE

OFF

KEYSTONE

1 2 3

ID CHANGE

LASER

VOLUME

RGB

BLANK button

Page 21

Operating (continued)

Freezing The Screen

Press the FREEZE button.

As illustrated on the right, a dialog will appear on the screen, and the screen will freeze at the current image.

Press the FREEZE button again to restore the

screen to normal.

FREEZE

The icon “||” will change to the icon “ ”. And after a couple of seconds, the dialog will be closed and the screen will be restored to normal.

memo

The freezing feature will automatically finish if a remote control’s button that changes some display state (ex. blanking the screen,

LASER INDICATOR

STANDBY/ON

VIDEO

LENS SHIFT

FOCUS ZOOM

–––

ASPECT

BLANK

ENTER

ESC MENU

POSITION

RESET AUTO

MAGNFY

PinP

FREEZE MUTE

OFF

KEYSTONE

1 2 3

ID CHANGE

LASER

VOLUME

RGB

FREEZE button

displaying a dialog or a menu, adjusting the picture, changing the input signal) is pressed, or a button of projector is pressed.

NOTE

•

If the projector continues projecting the same image for a long time (i.e. you forget to exit FREEZE mode),

the image might possibly remain as an afterimage. Do not leave the projector in FREEZE mode for too long.

Using The Magunify Feature

Press the MAGNIFY

button. As illustrated on the right, a dialog will appear on the screen to aid you in magnifying the picture.

Press the POSITION button, then use the cursor

buttons / / / to select the area to zoom.

Press the POSITION button again to finalize the

zoom area.

Use the cursor buttons / to adjust the zoom

level.

MAGNIFY

LASER INDICATOR

STANDBY/ON

VIDEO

LENS SHIFT

FOCUS ZOOM

–––

ASPECT

BLANK

ENTER

ESC MENU

POSITION

RESET AUTO

MAGNFY

PinP

FREEZE MUTE

OFF

KEYSTONE

1 2 3

ID CHANGE

LASER

VOLUME

RGB

Cursor buttons

POSITION button

MAGNIFY buttons

Press the MAGNIFY button again to close the

dialog and complete this operation.

memo

The magnify feature will automatically finish if the

OFF

automatic adjustment is execute, or the aspect, the signal type mode of video or the signal input state is changed.

Page 22

Operating (continued)

Displaying The Child Window

memo

This feature called "PinP (Picture in Picture)" is available only when a RGB signal is selected to main screen.

Press the PinP button.

The child window with a picture of a video signal will appear.

Press the PinP button again to change the size of

the child window or close the window.

Small child window Large child window

No child window

memo

You can select the video signal to display in the child window, and the position of the child window. Please refer to the items “P.INP. INPUT” and “P.INP. POSIT.” of the table of the section “INPUT Menu”.

Selecting An Audio Input

memo

This feature is available only when the child window is on the screen.

When the child window is on the

screen, press the VOLUME button. As illustrated on the right, a dialog will appear on the screen.

Use the cursor buttons / to

select an audio input.

RGB (Audio input for the main screen)

Video (Audio input for the child window)

memo

You also can adjust the volume using the cursor buttons The Volume”.

. Please refer to the section “Adjusting

VOLUME

RGB Video

LASER INDICATOR

STANDBY/ON

VIDEO

LENS SHIFT

FOCUS ZOOM

–––

ASPECT

BLANK

ENTER

ESC MENU

POSITION

RESET AUTO

MAGNFY

PinP

FREEZE MUTE

OFF

KEYSTONE

1 2 3

ID CHANGE

LASER INDICATOR

STANDBY/ON

VIDEO

LENS SHIFT

FOCUS ZOOM

–––

ASPECT

BLANK

ENTER

ESC MENU

POSITION

RESET AUTO

MAGNFY

PinP

FREEZE MUTE

OFF

KEYSTONE

1 2 3

ID CHANGE

LASER

VOLUME

LASER

VOLUME

RGB

PinP button

RGB

Cursor buttons

VOLUME button

Press the VOLUME button again to close the

dialog and complete this operation.

memo

Even if you don’t do anything, the dialog will automatically disappear after a few seconds.

Page 23

Multifunctional Settings

: SELECT

MENU MAIN PICTURE-1 PICTURE-2 INPUT AUTO SCREEN OPTION NETWORK

VOLUME SPEAKER IR REMOTE IR REMOTE ID LAMP TIME FILTER TIME SERVICE RESET

16 TURN ON

ALL 1234 h 4321 h

: SELECT

MENU MAIN PICTURE-1 PICTURE-2 INPUT AUTO SCREEN OPTION NETWORK

VOLUME SPEAKER IR REMOTE IR REMOTE ID LAMP TIME FILTER TIME SERVICE RESET

16 TURN ON

ALL 1234 h 4321 h

Multifunctional Settings

Using The Menu Functions

This projector has the following menus: MAIN, PICTURE-1, PICTURE-2, INPUT, AUTO, SCREEN, OPTION and NETWORK. Each of these menus is operated using the same methods. The basic operations of these menus are as follows.

Press the MENU button.

The menu will appear on the screen.

Use the cursor buttons

/ to select a menu, then press the (or the ENTER) button to progress.

LASER INDICATOR

STANDBY/ON

VIDEO

LENS SHIFT

FOCUS ZOOM

–––

ASPECT

BLANK

ENTER

ESC MENU

POSITION

RESET AUTO

MAGNFY

PinP

FREEZE MUTE

OFF

KEYSTONE

1 2 3

ID CHANGE

RGB

LASER

VOLUME

The display of the selected menu will appear.

Use the cursor buttons

/ to select an item, then press the (or the ENTER) button to progress. The operation display of the selected item will appear.

Use the cursor buttons / to operate the item.

memo

When you want to reset the adjustment, press the RESET button during the operation. Note that the items whose functions are performed simultaneously with operating (ex. LANGUAGE, WHISPER, H PHASE etc.) are not reset.

memo

When you want to return to the previous display, press the or ESC button.

Cursor buttons

MENU button

RESET button

ESC button

ENTER button

ex. Turning off the built-in speaker

1) Press the MENU button.

MENU MAIN PICTURE-1 PICTURE-2 INPUT AUTO SCREEN OPTION NETWORK

: SELECT

2) Select the “OPTION” using the button, then press the button.

3) Select the “SPEAKER” using the button, then press the button.

MENU MAIN

VOLUME

PICTURE-1

SPEAKER

PICTURE-2

IR REMOTE

INPUT

IR REMOTE ID

AUTO

LAMP TIME

SCREEN

FILTER TIME

OPTION

SERVICE

NETWORK

RESET

: SELECT

4) Use the cursor button to select the “TURN OFF”.

BRIGHT CONTRAST ASPECT WHISPER MIRROR LANGUAGE [Language] RESET

OPTION SPEAKER TURN ON TURN OFF

16 TURN ON

ALL 1234 h 4321 h

+0 +0 4:3 NORMAL NORMAL ENGLISH

OPTION SPEAKER TURN ON TURN OFF

Press the MENU button again to close the menu

display and complete this operation.

memo

Even if you don’t do anything, the menu will

automatically disappear after a few seconds

5) Press the MENU button.

Page 24

Multifunctional Settings (continued)

: SELECT

MENU MAIN PICTURE-1 PICTURE-2 INPUT AUTO SCREEN OPTION NETWORK

BRIGHT CONTRAST ASPECT WHISPER MIRROR LANGUAGE [Language] RESET

+0 +0 4:3 NORMAL NORMAL ENGLISH

ENGLISH  FRANÇAIS  DEUTSCH  ESPAÑOL  ITALIANO

NORSK  NEDERLANDS  日本語  PORTUGUÊS  中文

 SVENSKA   SUOMI  POLSKI

Multifunctional Settings (continued)

MAIN Menu

With the MAIN menu, the items shown in the table below can be performed. Perform each operation in accordance with the instructions in the table below.

Item Description

BRIGHT

CONTRAST

ASPECT

WHISPER

MIRROR

Adjust the brightness using the / buttons. : Light  Dark Adjust the contrast using the / buttons. : Strong  Weak Select an aspect ratio using the / buttons. :

■ At a M1-D signal NORMAL  4:3  16:9

The NORMAL keeps the original aspect ratio of the input signal.

■ At a RGB signal (not M1-D) 4:3  16:9

■ At a video signal 4:3  16:9  SMALL

memo At a HDTV signal of 1125i or 750p, only the 16:9 can be selected.

Select the NORMAL or the WHISPER using the / buttons. :

NORMAL  WHISPER

When the WHISPER is selected, acoustic noise and screen brightness are reduced.

Select a mirror status using the / buttons. :

NORMAL  H:INVERT  V:INVERT  H&V:INVERT

ex.

Select a menu language using the / buttons. :

LANGUAGE

Select the EXECUTE using the button to reset the MAIN menu items. :

RESET

EXECUTE  CANCEL

The items of the MAIN menu are collectively returned to the initial setting. Note that the items “WHISPER” and “LANGUAGE” are not reset.

Page 25

: SELECT

MENU MAIN PICTURE-1 PICTURE-2 INPUT AUTO SCREEN OPTION NETWORK

GAMMA COLOR BAL R COLOR BAL G COLOR BAL B SHARPNESS COLOR TINT MY MEMORY

NORMAL +0 +0 +0 +0 +0 +0 LOAD1

Multifunctional Settings (continued)

PICTURE-1 Menu

With the PICTURE-1 menu, the items shown in the table below can be performed. Perform each operation in accordance with the instructions in the table below.

Item Description

Select a gamma mode using the / buttons. :

NORMAL  CINEMA  DYNAMIC  CUSTOM Selecting the CUSTOM and then pressing the (or the ENTER) button calls the CUSTOM menu.

CUSTOM Menu

Select an item using the / buttons, and press the

(or the ENTER) button to perform each function.

GAMMA  COLOR TEMP  R  G  B

memo The R, G and B can be selected only when the

USER is selected under the COLOR TEMP.

GAMMA

NORMAL CINEMA DYNAMIC CUSTOM

: SELECT

GAMMA COLOR TEMP R G B

2.2 HIGH 100 100 100

GAMMA

COLOR BAL R

COLOR BAL G

COLOR BAL B

SHARPNESS

COLOR

TINT

GAMMA

COLOR TEMP

Adjust the gamma data using the / buttons. :

Up  Down

Select a color temperature using the / buttons. :

HIGH  MIDDLE  LOW  USER

Adjust the red color level for the USER mode of the COLOR TEMP using the / buttons. : Strong  Weak

Adjust the green color level for the USER mode of the COLOR TEMP using the / buttons. : Strong  Weak

Adjust the blue color level for the USER mode of the COLOR TEMP using the / buttons. : Strong  Weak

Adjust the red color balance using the / buttons. :

Strong  Weak

Adjust the green color balance using the / buttons. :

Strong  Weak

Adjust the blue color balance using the / buttons. :

Strong  Weak

Adjust the sharpness using the / buttons. :

Clear  Soft

memo This item can be selected only at a video signal.

Adjust the whole color using the / buttons. :

Strong  Weak

memo This item can be selected only at a video signal.

Adjust the tint using the / buttons. :

Green  Red

memo This item can be selected only at a video signal.

(This table is continued to the following page.)

Page 26

Multifunctional Settings (continued)

LOAD1  LOAD2  LOAD3  LOAD4

SAVE1  SAVE2  SAVE3  SAVE4

Multifunctional Settings (continued)

PICTURE-1 Menu (continued)

Item Description

Select a command to load or save using the / buttons, and then press the (or the ENTER) button to perform the function.:

MY MEMORY

RESET

This projector has 4 numbered memories for adjustment data. Performing the SAVE1, SAVE2, SAVE3 or SAVE4 puts the current adjustment data on the memory whose number corresponds with the command’s number. Performing the LOAD1, LOAD2, LOAD3 or LOAD4 loads the data on the memory whose number corresponds with the command’s number, and adjusts the picture automatically depending on the data.

Select the EXECUTE using the button to reset the PICTURE-1 menu items. :

EXECUTE  CANCEL The items of the PICTURE-1 menu are collectively returned to the initial setting. Note that the items “MY MEMORY” and “GAMMA” of the CUSTOM menu under the item “GAMMA” are not reset.

Page 27

Multifunctional Settings (continued)

: SELECT

MENU MAIN PICTURE-1 PICTURE-2 INPUT AUTO SCREEN OPTION NETWORK

V POSITION H POSITION H PHASE H SIZE OVER SCAN RESET

20 142 31 1344 95

Multifunctional Settings (continued)

PICTURE-2 Menu

With the PICTURE-2 menu, the items shown in the table below can be performed. Perform each operation in accordance with the instructions in the table below.

memo This menu cannot be selected at a M1-D signal.

Item Description

V POSITION

H POSITION

V POSITION

H SIZE

Adjust the vertical position using the / buttons. :

Up  Down

memo This item can be selected only at a RGB signal.

Adjust the horizontal position using the / buttons. :

Left  Right

memo This item can be selected only at a RGB signal.

Adjust the horizontal phase to eliminate flicker using the / buttons. :

Right  Left

memo This item can be selected only at a RGB signal or a component video

signal other than a COMPONENT port input of 525i/625i/SCART RGB. Adjust the horizontal size using the / buttons. :

Large  Small

memo This item can be selected only at a RGB signal. memo When this adjustment is excessive, the picture may not be displayed

correctly. In such a case, please reset the adjustment pressing the RESET button during this operation.

OVER SCAN

RESET

Adjust the over-scan ratio using the / buttons. :

Small  Large

memo This item can be selected only at a video signal. memo When this adjustment is too large, certain degradation may appear at

the frame area of the picture. In such a case, please adjust small. Select the EXECUTE using the button to reset the PICTURE-2 menu items. :

EXECUTE  CANCEL The items of the PICTURE-2 menu are collectively returned to the initial setting. Note that the item “H PHASE” is not reset.

Page 28

Multifunctional Settings (continued)

: SELECT

MENU MAIN PICTURE-1 PICTURE-2 INPUT AUTO SCREEN OPTION NETWORK

COLOR SPACE COMPONENT VIDEO 3D-YCS VIDEO NR P. INP. INPUT P. INP. POSIT. POWERUP INPUT

AUTO COMPONENT AUTO TURN OFF LOW VIDEO

RGB

Multifunctional Settings (continued)

INPUT Menu

With the INPUT menu, the items shown in the table below can be performed. Perform each operation in accordance with the instructions in the table below.

Item Description

Select a color space mode using the / buttons. :

AUTO  RGB  SMPTE240  REC709  REC601

COLOR SPACE

COMPONENT

VIDEO

3D-YCS

Selecting the AUTO automatically selects the optimum mode.

memo This item can be selected only at a RGB signal or a component video

signal other than a COMPONENT port input of 525i/625i/SCART RGB.

memo The AUTO operation may not work well at some signals. In such a case,

select the SMPTE240 or the REC709 for a HDTV signal. Select a function of COMPONENT port using the / buttons. :

COMPONENT  SCART RGB When the SCART RGB is selected, the COMPONENT port function as a port for a SCART RGB signal input. Please refer to the section “Connecting Your Devices”.

Select a signal type mode using the / buttons. :

AUTO  NTSC  PAL  SECAM  NTSC4.43  M-PAL  N-PAL Selecting the AUTO automatically selects the optimum mode.

memo This item is performs only at a video signal from the VIDEO port or the S-

VIDEO port. For a component video signal, the signal type is identified automatically independently of this function.

memo The AUTO operation may not work well at some signals. If the picture

becomes unstable (ex. a irregular picture, a color lack), please select the mode depending on the input signal.

Select the TURN ON or the TURN OFF using the / buttons. :

TURN ON  TURN OFF When the TURN ON is selected, the 3D-YCS mode works for a completely still image, or images with few motions.

memo This item performs only at a video signal of NTSC3.58. memo When this function performs, the setting of the item “VIDEO NR” of this

INPUT menu is not effective.

VIDEO NR

Select a noise reduction level using the / buttons. :

HIGH  MIDDLE  LOW The noise on screen is reduced according to the selected level.

memo This item performs only at a video signal from the VIDEO port or the S-

VIDEO port. At a video signal of NTSC3.58, this function performs only when the TURN OFF is selected to the item “3D-YSC” of this INPUT menu.

memo When this adjustment is excessive, certain degradation may appear on

the picture.

(This table is continued to the following page.)

Page 29

Multifunctional Settings (continued)

INPUT Menu (continued)

Item Description

Select a signal input port for the child window using the / buttons. :

P.IN P. INPUT

P.IN P. POSIT.

POWERUP

INPUT

INFORMATION

S2-ASPECT

RESET

VIDEO  S-VIDEO

memo About the child window, please refer to the section “Displaying the Child

Window”. Select the display position of the child window using the / buttons. :



memo About the child window, please refer to the section “Displaying the Child

Window”. Select a signal input port to display just when the projector is turned on, using

the / buttons. :

LAST INPUT  M1-D  RGB  BNC  COMPONENT  S-VIDEO  VIDEO

Selecting the LAST INPUT selects the port that was used at the last time. Pressing the (or the ENTER) button displays the INPUT INFORMATION

menu. The INPUT INFORMATION menu shows the information about the current signal input as illustrated below.

INPUT-INFORMATION

RGB

1024x768 @60.0

FRAME LOCK

INPUT-INFORMATION

S-VIDEO

SECAM

AUTO

memo The “FRAME LOCK” message means the frame lock function is working.

This function automatically works when a RGB signal with vertical frequency of 50 to 60 is input, and it displays a moving picture more smoothly.

memo The “SCART RGB” message means the COMPONENT port is working

as a SCART RGB port. Please refer to the item “COMPONENT” in this table. Select the TURN ON or the TURN OFF using the / buttons. :

TURN ON  TURN OFF When the TURN ON is selected, an S2-video signal can be identified and the optimum aspect ratio is automatically selected.

memo This item is performs only at a S-VIDEO signal. memo When the ASPECT button is used or the item “ASPECT” of the MAIN

menu is operated, the TURN OFF will be automatically selected to this item. Select the EXECUTE using the button to reset the INPUT menu items. :

EXECUTE  CANCEL The items of the INPUT menu are collectively returned to the initial setting. Note that the item “INFORMATION” is not reset.

INPUT-INFORMATION

COMPONENT

575i @50

SCART RGB

Page 30

Multifunctional Settings (continued)

: SELECT

MENU MAIN PICTURE-1 PICTURE-2 INPUT AUTO SCREEN OPTION NETWORK

ADJUST POWER OFF POWER ON SEARCH RESET

0 min TURN ON TURN ON

Multifunctional Settings (continued)

AUTO Menu

With the AUTO menu, the items shown in the table below can be performed. Perform each operation in accordance with the instructions in the table below.

Item Description

Pressing the (or the ENTER) button performs the automatic adjustment.

■ At a RGB signal The vertical position (V POSITION), the horizontal position (H POSITION), the clock phase (H PHASE) and the horizontal size (H SIZE) will be automatically adjusted.

memo Make sure that the application window is set to its maximum size prior to

attempting to use this feature. Dark pictures may still be incorrectly adjusted. Use a bright screen when adjusting.

ADJUST

POWER OFF

POWER ON

■ At a video signal The signal type mode best suited for the respective input signal will be selected automatically.

memo This function is available only when the AUTO is selected to the item

“VIDEO” of the INPUT menu. For a component video signal, the signal type is identified automatically independently of this function.

memo This operation requires approximately 10 seconds, and the message

“AUTO IN PROGRESS” is displayed during the operation.

memo This operation may not work well at some signals. If the picture

becomes unstable (ex. a irregular picture, a color lack), please select the suitable mode to the item “VIDEO” of the INPUT menu.

Set the time using the / buttons. :

Long (max. 99 minutes)  Short (min. 0 minute = DISABLE)

AUTO

ex.

POWER OFF

ENABLE

1min

POWER OFF

DISABLE

When the time is set to 1 to 99, the projector lamp will go off and the STANDBY/ON indicator begins blinking when the passed time with a proper signal (without no-signal and an unsuitable signal) reaches at the set time. Please refer to the section “Turning Off The Power”.

Select the TURN ON or the TURN OFF using the / buttons.:

TURN ON  TURN OFF

When the TURN ON is selected, you can turn the projector on without pressing the STANDBY/ON button. Please refer to the section “Turning Off The Power”.

AUTO

0min

(This table is continued to the following page.)

Page 31

Multifunctional Settings (continued)

AUTO Menu (continued)

Item Description

Select the TURN ON or the TURN OFF using the / buttons. :

TURN ON  TURN OFF When the TURN ON is selected, detecting no signal cycles through input ports and displays the picture of retrieved signal.

RESET

M1-D RGB

VIDEO S-VIDEO

memo When the TURN ON is selected, pressing the RGB button selects the

M1-D ports, and pressing the VIDEO button selects the COMPONENT port.

memo If no signal is found or the projector is unstable to find an input signal at

any of its ports, it will return to the state it was in prior to the search. Select the EXECUTE using the button to reset the AUTO menu items. :

EXECUTE  CANCEL The items of the AUTO menu are collectively returned to the initial setting. Note that the item “ADJUST” is not reset.

BNC

COMPONENT

Page 32

Multifunctional Settings (continued)

: SELECT

MENU MAIN PICTURE-1 PICTURE-2 INPUT AUTO SCREEN OPTION NETWORK

BLANK START UP MyScreen MyScreen SIZE MyScreen LOCK MENU POSITION MESSAGE RESET

BLACK ORIGINAL

x1 TURN OFF

TURN ON

using the / / / buttons.:

Multifunctional Settings (continued)

SCREEN Menu

With the SCREEN menu, the items shown in the table below can be performed. Perform each operation in accordance with the instructions in the table below.

Item Description

Select a type of the BLANK screen using the / buttons. :

MyScreen  ORIGINAL  BLUE  WHITE  BLACK

The BLANK screen is the screen, which is displayed by pressing the BLANK

BLANK

START UP

MyScreen

button. The MyScreen is the screen you can register a desired screen, and the ORIGINAL is the existing standard screen. The BLUE, the WHITE and the BLACK are the non-pattered (plain) screens in each color.

memo To avoid remaining as an afterimage, the MyScreen and the ORIGINAL

screens will change to the BLACK screen after several minutes.

memo For the MyScreen, please refer to the item “MyScreen” in this table.

Select a type of the START UP screen using the / buttons. :

MyScreen  ORIGINAL  TURN OFF The START UP screen is the screen, which is displayed by detecting no signal or an unsuitable signal. The MyScreen is the screen you can register a desired screen, and the ORIGINAL is the existing standard screen. When the TURN OFF is selected, the BLUE is used.

memo To avoid remaining as an afterimage, the MyScreen and the ORIGINAL

screens will change to the BLANK after several minutes. If also the BLANK screen is the MyScreen or the ORIGINAL, it will change to the BLACK screen.

memo About the MyScreen, please refer to the item “MyScreen” in this table.

About the BLUE, BLACK and BLANK screens, please refer to the item “BLANK” in this table.

Pressing the (or the ENTER) button starts the MyScreen registration. Please see the flow chart on the following page.

MyScreen SIZE

MyScreen LOCK

MENU POSITION

Select the size of the MyScreen using the / buttons. :

x1  FULL Select the TURN ON or the TURN OFF using the / buttons.:

TURN ON  TURN OFF The TURN ON disables the operation of the item “MyScreen” of this SCREEN menu.

After pressing the (or ENTER) button, adjust the menu position



Left  +  Right



Down

memo To finish this operation, press the ESC button but not the button.

(This table is continued to the following page.)

Page 33

Multifunctional Settings (continued)

MyScreen is pointed on the SCREEN menu.

The MyScreen

menu appears.

Do you capture the picture from

the current screen?

Registering.

It takes about 1 minute to register.

Just when the picture registration is completed

the registered screen and

the message of the right is displayed for a few seconds.

If the picture registration failed,

the message of the right is displayed for a few seconds.

The picture freeze and the frame for capturing appears.

Move the frame to the position of the picture

which you want to use, using / / / buttons,

and press the ENTER button to register.

NO: Press the ESC/RESET button

YES: Press the ENTER button

If the ESC/RESET button is pressed ...

Press the button

:NO

ESC ENT

:YES

MyScreen

Do you start capturing this picture?

:RETURN

ESC

ENT

:NEXT

MyScreen Move the capture area

as you want.

My Screen

45%

MyScreen registration is finished.

A capturing error has occurred.

Please try again.

Multifunctional Settings (continued)

SCREEN Menu (continued)

Item Description

Select the TURN ON or the TURN OFF using the / buttons. :

TURN ON  TURN OFF

When the TURN ON is selected, the following message function works.

The message of the “AUTO IN PROGRESS” for the auto adjustment.

MESSAGE

RESET

How to register your picture as the MyScreen

The message of the ”NO INPUT IS DETECTED” The message of the ”SYNC IS OUT OF RANGE” The message of the ”Searching …” The message of the “Detecting …” The indication of the input signal by input change. The indication of the aspect ratio by changing the aspect ratio. The indication of “FOCUS” by adjusting the focus.

Select the EXECUTE using the button to reset the SCREEN menu items. :

EXECUTE  CANCEL

The items of the SCREEN menu are collectively returned to the initial setting.

Page 34

Multifunctional Settings (continued)

: SELECT

MENU MAIN PICTURE-1 PICTURE-2 INPUT AUTO SCREEN OPTION NETWORK

VOLUME SPEAKER IR REMOTE IR REMOTE ID LAMP TIME FILTER TIME SERVICE

RESET

16 TURN ON

ALL 1234 h 4321 h

Multifunctional Settings (continued)

OPTION Menu

With the OPTION menu, the items shown in the table below can be performed. Perform each operation in accordance with the instructions in the table below.

Item Description

VOLUME

SPEAKER

IR REMOTE

IR REMOTE ID

LAMP TIME

FILTER TIME

Adjust the volume using the / buttons. :

High  Low Select the TURN ON or the TURN OFF using the / buttons. :

TURN ON  TURN OFF When the TURN ON is selected, the built-in speaker works.

Select a remote sensor using the / button (1), then switch it using the ENTER button (2). :

(1) FRONT  TOP  REAR (2)  (Off) (On)

memo A sensor cannot be turned off when the other two are off.

OPTION IR REMOTE FRONT TOP REAR ENT

Always at least one sensor is on. Select a number as an ID number for remote control using the / buttons. :

ALL  1  2  3 The projector is controlled by the remote control whose ID CHANGE switch is set into the position of the same number as this number. When the ALL is selected, the projector is controlled by a remote control irrespective of the position of the ID CHANGE switch.

memo Please refer to the section “Using The Remote ID Feature”.

Pressing the RESET button for about 3 seconds displays the LAMP TIME menu. Select the RESET using button to reset the timer. :

RESET  CANCEL Selecting the RESET resets the count of the lamp timer to 0.

memo Perform this function only when you have replaced the lamp. The lamp

timer counts the used time of the current lamp, to display the messages about the lamp. Incorrect performing causes incorrect operation of the messages.

memo About replacing the lamp, please refer to the section” Lamp”.

Pressing the RESET button for about 3 seconds displays the FILTER TIME menu. Select the RESET using button to reset the timer. :

RESET  CANCEL Selecting the RESET resets the count of the lamp timer to 0.

memo Perform this function only when you have cleaned or replaced the air

filter. The filter timer counts the used time of the air filter after cleaning or replacement, to display the messages about the air filter. Incorrect performing causes incorrect operation of the messages.

memo About caring for the air filter, please refer to the section “Air Filter”.

(This table is continued to the following page.)

Page 35

Multifunctional Settings (continued)

OPTION Menu (continued)

Item Description

Pressing the (or the ENTER) button calls the SERVICE menu.

SERVICE Menu

Select an item using the / buttons, and press the (or the ENTER) button to per form each function. :

FANSPEED  AUTO ADJUST  LENS TYPE  LENS LOCK

Select the fan speed level using the / buttons. :

HIGH  NORMAL

FANSPEED

AUTO

ADJUST

SERVICE

LENS TYPE

LENS LOCK

The HIGH ups rotation speeds of fans, though. Please use this function in using a projector at highlands etc.

memo Note that the projector is noisier when the HIGH is

selected. Select the ENABLE or the DISABLE using the /

buttons. :

ENABLE  DISABLE When you want to keep the current adjustment state, select the DISABLE. When the ENABLE is selected, detecting a signal change to a RGB signal performs the automatic adjustment of the vertical position (V POSITION), the horizontal position (H POSITION), the clock phase (H PHASE) and the horizontal size (H SIZE).

Select the lens type currently used using the / buttons. :

AUTO  1  2  3  4  5 Please select depending on the following. AUTO: automatically selects optimum mode.

1: for a standard lens (Type NL-500 etc.)

2: for a fixed short throw lens (Type FL-501 etc.)

3: for a short throw lens (Type SL-502 etc.)

4: for a long throw lens (Type LL-503 etc.)

5: for a super long throw lens (Type LL-504 etc.)

memo This setting has an influence on the keystone distortion

etc.

memo About the optional lens, ask your dealer.

Select the TURN ON or the TURN OFF using the buttons. :

TURN ON  TURN OFF Selecting the TURN ON locks the adjustment of the lens shift, the zoom and the focus.

SERVICE FANSPEED AUTO ADJUST LENS TYPE LENS LOCK

: SELECT

NORMAL ENABLE AUTO TURN OFF

RESET

Select the EXECUTE using the button to reset the OPTION menu items. :

EXECUTE  CANCEL The items of the OPTION menu are collectively returned to the initial setting. Note that the items “VOLUME”, “LAMP TIME” and “FILTER TIME” are not reset.

Page 36

Multifunctional Settings (continued)

: SELECT

MENU MAIN PICTURE-1 PICTURE-2 INPUT AUTO SCREEN OPTION NETWORK

SETUP DHCP INFORMATION RESET

TURN OFF

Multifunctional Settings (continued)

NETWORK Menu

This projector provides the NETWORK function. If you use this function, please set up the projector according to the Network environment in which you use it.

memo When you use a Network suitable to the DHCP function, the following

operation is not required commonly, because the TURN ON is selected to the item “DHCP” at the shipment time. Please see the section “Network Setting Up”.

Item Description

Pressing the (or the ENTER) button calls the IP ADDRESS menu.

memo This item performs only when the TURN OFF

is set to the item “DHCP” of this NETWORK menu. The IP Address is identification number of the projector on the Network.

1. Set the IP Address using the / buttons.

memo The same number as the IP Address of other units cannot be used.

Pressing the (or the ENTER) button at the IP

SETUP

DHCP

ADDRESS menu calls the SUBNET MASK menu. The SUBNET MASK is an address of the Network.

2. Set the same number as the address of the Network to be used. Pressing the (or the ENTER) button at the SUBNET MASK menu calls the DEFAULT GATEWAY menu. The DEFAULT GATEWAY is the address of the main device.

3. Set the same number as the address of the device as gateway to an outer Network.

Select the TURN ON or the TURN OFF using the / buttons. :

TURN ON  TURN OFF

When you use a Network unsuitable to the DHCP function, select the TURN OFF.

NETWORK - SETUP

IP ADRRESS

192 . 168 . 1 . 24

ESC ENT

:RETURN

NETWORK - SETUP

SUBNET MASK

255 . 255 . 255 . 1

ESC ENT

:RETURN

NETWORK - SETUP DEFAULT GATEWAY

255 . 255 . 255 . 0

ESC ENT

:RETURN

:NEXT

NETWORK

DHCP

TURN ON

TURN OFF

INFORMATION

RESET

Pressing the (or the ENTER) button displays the INFORMATION menu. The INFORMATION menu shows the information about the current Network setting as illustrated

NETWORK-INFORMATION IP ADRRESS 192. 168. 1. 24 SUBNETMASK 255. 255. 255. 0 DEFAULT GATEWAY 255. 255. 255. 0 MAC ADRRESS 00. E0. 47. 03. 0C. D8

below. Select the EXECUTE using the button to reset the NETWORK menu items. :

EXECUTE  CANCEL

The items of the NETWORK menu are collectively returned to the initial setting.

Page 37

Network Setting Up

This projector provides the NETWORK function. If you use this function, please consult your dealer for information.

To start, connect the NETWORK port to a gateway device via a RJ-45 (10BASE-1) cable, then set up the projector according to the Network environment in which you use it.

When you use a Network unsuitable to the DHCP function

Please set the IP Address, the Subnet Mask, the Gateway and the DHCP (on/off) using the NETWORK menu, referring to the section “NETWORK Menu”.

When you use a Network suitable to the DHCP function or has been set up

You can set the IP Address, the Subnet Mask, the Gateway and the DHCP (on/off) using a Web Browser of the computer connected to the Network. Although it needs a Web Browser of Internet Explorer 4.0 or higher.

Input the same IP address as set to the projector, to the Web Browser of the computer connected to LAN.

ex. Case of IP Address = 192.168.1.11

1) Input “http://192.168.1.11”.

2) Click “ENTER”.

3) Input the required data according to the screen.

4) Make sure of the input data, then click "Write".

memo These setting will be active after reboot. These

setting will be stored, and used when DHCP is OFF.

5) Click “Return to top page”.

6) Click “REBOOT” to complete this operation.

Page 38

Lamp

WARNING

The projector uses a high-pressure mercury glass lamp. The lamp can break with a loud bang, or burn out, if jolted or scratched, handled while hot, or worn over time.

Note that each lamp has a different lifetime, and some may burst or burn out soon after you start using them. In addition, when the bulb bursts, it is possible for shards of glass to fly into the lamp housing, and for gas containing mercury to escape from the projector’s vent holes.

About disposal of a lamp • This product contains a mercury lamp; do not put in trash. Dispose of in accord with environmental laws. For lamp recycling, go to www.lamprecycle.org. (in USA) For product disposal, contact your local government agency or www.eiae.org (in the US) or www.epsc.ca (in Canada). For more information, call your dealer.

• If the lamp should break (it will make a loud bang when it does), unplug the power cord from the outlet, and make sure to request a replacement lamp from your local dealer. Note that shards of glass could damage the projector’s internals, or cause injury during handling, so please do not try to clean the projector or replace the lamp yourself.

Disconnect the

plug from the

power outlet

• If the lamp should break (it will make a loud bang when it does), ventilate the room well, and make sure not to breathe the gas that comes out of the projector vents, or get it in your eyes or mouth.

• Before replacing the lamp, make sure the power switch is off and the power cable is not plugged in, then wait at least 45 minutes for the lamp to cool sufficiently. Handling the lamp while hot can cause burns, as well as damaging the lamp.

• Do not open the lamp cover while the projector is suspended from above. This is dangerous, since if the lamp’s bulb has broken, the shards will fall out when the cover is opened. In addition, working in high places is dangerous, so ask your local dealer to have the lamp replaced even if the bulb is not broken.

• Do not use the projector with the lamp cover removed. At the lamp replacing, make sure that the screws are screwed in firmly. Loose screws could result in damage or injury.

HIGH VOLTAGE HIGH TEMPERATURE HIGH PRESSURE

• Use only the lamp of the specified type DT00601

• If the lamp breaks soon after the first time it is used, it is possible that there are electrical problems elsewhere besides the lamp. If this happens, contact your local dealer or a service representative.

• Handle with care: jolting or scratching could cause the lamp bulb to burst during use.

• If the indicators or a message prompts you to replace the lamp (see the section “Related Messages” and “Regarding the indicator Lamps”), replace the lamp as soon as possible. Using the lamp for long periods of time, or past the replacement date, could cause it to burst. Do not use old (used) lamps; this is a cause of breakage.

Page 39

Lamp (continued)

CO LAMP

Lamp (continued)

Replacing The Lamp

If the indicators or a message prompts you to replace the lamp, replace the lamp as soon as possible.

Turn off the projector, and unplug the power cord. Allow the lamp bulb to cool for at

least 45 minutes.

Contact your dealer to prepare a new lamp. Tell the dealer your lamp type number.

If the projector is mounted on the ceiling, or if the lamp has broken, also ask the dealer to replace the lamp.

In the case of replacement by yourself,

After making sure that the projector has cooled

adequately, slide the knob of a lamp cover lock as shown in the Figure. Then, one side of the lamp cover is raised. Pull up the lamp cover and remove it, as shown in the Figure.

Unscrew the 3 screws, and slowly pull out the lamp

by the handle. Be careful not to touch the inside of the lamp case.

Insert the new lamp, and tighten the 3 screws firmly

to lock it in place.

Lamp cover knob

Screws

Lamp cover

TEMP

LAMP

STANDBY/ON

VIDEO

S-VIDEO

OMPON

ENT

IN TE R

LENS SHIFT

BNG

RGB

RESET

INPUT

M1-D

FOCUS

ZOOM

KEYSTONE

CO LAMP

TEMP

LAMP

STANDBY/ON

VIDEO

S-VIDEO

COMPONENT

IN T ER

LENS SHIFT

BNG

RGB

RESET

INPUT

M1-D

FOCUS

ZOOM

KEYSTONE

CO LAMP

Interlocking the 2 tabs of the lamp cover to the

projector, put the lamp cover on the projector. Then push the point of the lamp cover to fix it, as shown in

Tabs

the Figure. Make sure that the lamp cover does’t come up.

Turn on the projector, and reset the lamp timer.

(1) While the projector running, press the MENU button to open the menu. (2) Choose the “OPTION” on the menu using the

button, then press the

button or ENTER button.

(3) Choose the “LAMP TIME” using the

button, then press and hold the

RESET button for 3 seconds.

(4) Choose the “RESET” using the button.

memo When the lamp has been replaced after the message of "THE POWER WILL

TURN OFF AFTER 0hr." is displayed, complete the following operation within 10 minutes of switching power on.

memo Incorrectly resetting of the lamp timer (resetting without replacement, or

neglect of resetting after replacement) will result in incorrect message functions.

TEMP

LAMP

STANDBY/ON

VIDEO

S-VIDEO

COMPONENT

NT E R

LENS SH

BNG

IFT

RGB

RESET

INPUT

M1-D

FOCUS

ZOOM

KEYSTONE

CO LAMP

Page 40

Air Filter

WARNING • Please carefully read the “User’s Manual - Safety Guide.

• Before caring, make sure the power switch is off and the power cable is not

plugged in, then wait at least 45 minutes for the lamp to cool sufficiently.

• Use only the air filter of the specified type NJ08081

• Do not use the projector with the air filter and filter cover removed. The use without the air filter could result in damage.

CAUTION

• If the air filter becomes clogged by dust or the like, internal

temperature rises and could cause malfunction. The power is automatically turned

off in order to prevent the projector from overheating internally.

Caring For The Air Filter

The air filter should be cleaned about every 100 hours. If the indicators or a message prompts you to clean the air filter, clean the air filter as soon as possible. If the soiling will not come off the air filter, or it becomes damaged, then it needs to be replaced. Please replace the air filter as soon as possible.

memo When you replace the lamp, please replace also the air filter.

Turn off the projector, and unplug the power cord. Allow the lamp bulb to cool for at

least 45 minutes.

After making sure that the projector has cooled adequately, remove the filter cover

and air filter.

Apply a vacuum cleaner to the top of the filter cover and

the air filter to clean. If the soiling will not come off the air filter, or it becomes damaged, it needs to be replaced. If the air filter needs to be replaced, contact your dealer to prepare a new air filter. Tell the dealer your air filter type.

Insert the cleaned air filter or a new air filter, and replace

the filter cover.

Turn on the projector power, and reset the filter timer.

(1) While the projector running, press the MENU button to

Hold the release button

open the menu.

(2) Choose the “OPTION” on the menu using the

button, then press the button or ENTER button.

(3) Choose the “FILTER TIME” using the

button, then

press and hold the RESET button for 3 seconds.

(4) Choose the “RESET” using the button.

memo Incorrectly resetting of the filter timer (resetting

without replacement, or neglect of resetting after replacement) will result in incorrect message functions.

Hold the release

buttons of the filter

cover while pulling

down it.

P M A

MP E

ON /

ANDBY

VIDEO

N ME

DEO

N I

US C

T N

COMPO NG B

U P N

RCH

RGB

SEA

S N

E L

-D 1 M

N O T S

of the air filter while

pulling out it.

LAM

MP E T

ON /

TANDB

S O

DE I V

N E M

-VI S

N I

CUS O

T N

E E R

OMP C

U P N I

RGB

N LE

N O

KEYS

Page 41

Other Care

WARNING • Please carefully read the “User’s Manual - Safety Guide”.

• Before caring, make sure the power switch is off and the power cable is not

plugged in.

• Be cautious of high temperature. Do not touch about the lens and ventilation openings during use or immediately after use prevent a burn.

• Never try to care for the inside of the unit yourself. Doing so is dangerous.

CAUTION

peeling paint, etc.

• Do not use cleaner or chemicals other than those listed below, including benzene and paint thinner.

• Do not use aerosols or sprays.

• Do not polish or wipe with hard objects.

• Incorrect care could have adverse influence such as discoloration,

Caring For The Inside Of The Projector

In order to ensure the safe use of your projector, please have it cleaned and inspected by your local dealer about once every 2 years.

Caring For The Lens

Turn off the projector, and unplug the power cord.

Lightly wipe the lens with a commercially available lens-cleaning wipe. Do not touch

the lens directly with your hand.

Caring For The Cabinet And Remote Control

Turn off the projector, and unplug the power cord.

Wipe lightly with gauze or a soft cloth.

memo If soiling is severe, dip soft cloth in water or a neutral cleaner dilute in water,

and wipe lightly after wringing well. Then, wipe lightly with a soft, dry cloth.

Page 42

roubleshooting

TTroubleshooting

Related Messages

When the unit's power is on, messages such as those shown below may be displayed. When any such message is displayed on the screen, please respond as described below. If the same message is displayed after the treatment, or if a message other than the following appears, please contact your dealer or service company.

memo Although these messages will be automatically disappeared around several

minutes, it will be reappeared every time the power is turned on.

Message Description

CHANGE THE LAMP

AFTER REPLACING LAMP,

RESET THE LAMP TIMER.

The time the lamp timer has counted is approaching 2000 hours.

Preparation of a new lamp, and an early lamp change is recommended. After you have change the lamp, please be sure to reset the lamp timer.

CHANGE THE LAMP

AFTER REPLACING LAMP,

RESET THE LAMP TIMER.

THE POWER WILL TURN OFF

AFTER ** hr.

CHANGE THE LAMP

AFTER REPLACING LAMP,

RESET THE LAMP TIMER.

THE POWER WILL TURN OFF

AFTER 0 hr.

NOTE

• A lamp has a finite product life. Lamps are characterized by the fact that,

The time the lamp timer has counted is approaching 2000 hours, so a lamp change within ** hours is recommended.

When lamp usage reaches 2000 hours, the power will automatically be turned off. Please change the lamp by referring to the section “Lamp”. After you have changed the lamp, please be sure to reset the lamp timer.

As the time the lamp timer has counted has reached 2000 hours, the power will soon be automatically turned off.

Please immediately turn the power off, and change the lamp by referring to the section “Lamp”. After changing the lamp, please be sure to reset the lamp timer.

(This table is continued to the following page.)

after long hours of usage, a lamp will no longer light up, or the lamp will break or burst, etc. This projector is equipped with an automatic shut-down function, such that the power will automatically be turned off when lamp usage time has reached 2000 hours. Please be aware, however, that among lamp types, there are major differences in product lifetimes; a lamp may thus fail to light even prior to the functioning of the automatic shut-down function of this projector.

Page 43

roubleshooting (continued)

TTroubleshooting (continued)

Related Messages

Message Description

CLEAN THE AIR FILTER

POWER OFF FIRST,

THEN CLEAN THE AIR FILTER.

AFTER CLEANING THE AIR

FILTER,

RESET THE FILTER TIMER.

CHECK THE AIR FLOW

NO INPUT IS DETECTED

ON ***

SYNC IS OUT OF RANGE

ON *** fH *****kHz fV *****Hz

(continued)

The time the filter timer has counted has reached 100 hours.

Please clear or change the air filter by referring to the section “Air Filter”. After caring for the air filter, please be sure to reset the filter timer.

The internal portion temperature is rising.

Please turn the power OFF, and allow the unit to cool down at least 20 minutes. After the projector has sufficiently cooled down, please make confirmation of the following items, and then turn the power on again.

• Is there blockage of the air passage aperture?

• Is the air filter dirty?

• Does the peripheral temperature exceed 35°C?

There is no input signal.

Please confirm the signal input connection, and the status of the signal source.

The horizontal or vertical wavelength of the inputted signal is outside of the response parameters of this unit.

Please confirm the specs for this unit or the signal source specs.

Page 44

roubleshooting (continued)

TTroubleshooting (continued)

Regarding The Indicator Lamps

Lighting and flashing of the STANDBY/ON indicator, the LAMP indicator, and the TEMP indicator have the meanings as described in the table below. Please respond in accordance with the instructions within the table. If the same indication is displayed after the treatment, or if an indication other than the following is displayed, please contact your dealer or service company.

NOTE

•

When the interior portion has become overheated, for safety purposes, the power source is automatically turned off, and the indicator lamps may also be turned off. In such a case, press the “○” (OFF) side of the main power switch, and wait at least 45 minutes. After the projector has sufficiently cooled down, please make confirmation of the attachment state of the lamp and lamp cover, and then turn the power on again.

STANDBY/ON

indicator

Lighting

in Orange

Blinking

in Green

Lighting

in Green

Blinking

in Orange

LAMP

indicator

Turned

off

Turned

off

Turned

off

Turned

off

TEMP

indicator

Turned

off

Turned

off

Turned

off

Turned

off

Description

The projector is in a standby state.

Please refer to the section “Power On/Off”.

The projector is warming up.

Please wait.

The projector is in an on state.

Ordinary operations may be performed.

The projector is cooling down.

Please wait.

The projector is cooling down. A certain error has

Blinking

in Red

(discre-

tionary)

(discre-

tionary)

been detected.

Please wait until the STANDBY/ON indicator finishes blink, and then perform the proper response measure using the item descriptions below as reference.

The lamp does not light, and there is a possibility that interior portion has become heated.

Please turn the power off, and allow the unit to cool down at least 20 minutes. After the projector has sufficiently cooled

Lighting

in Red

Lighting

in Red

Turned

off

down, please make confirmation of the following items, and then turn the power on again.

• Is there blockage of the air passage aperture?

• Is the air filter dirty?

• Does the peripheral temperature exceed 35°C? If the same indication is displayed after the treatment, please change the lamp by referring to the section “Lamp”.

(This table is continued to the following page.)

Page 45

roubleshooting (continued)

TTroubleshooting (continued)

Regarding The Indicator Lamps

STANDBY/ON

indicator

Lighting

in Red

Lighting

in Red

Lighting

in Red

LAMP

indicator

Blinking

in Red

Turned

off

Turned

off

TEMP

indicator

Turned

off

Blinking

in Red

Lighting

in Red

Either there is no lamp and/or lamp cover, or either of these has not been properly fixed.

Please turn the power off, and allow the unit to cool down at least 45 minutes. After the projector has sufficiently cooled down, please make confirmation of the attachment state of the lamp and lamp cover, and then turn the power on again. If the same indication is displayed after the treatment, please contact your dealer or service company.

The cooling fan is not operating.

Please turn the power off, and allow the unit to cool down at least 20 minutes. After the projector has sufficiently cooled down, please make confirmation that no foreign matter has become caught in the fan, etc., and then turn the power on again. If the same indication is displayed after the treatment, please contact your dealer or service company.

There is a possibility that the interior portion has become heated.

Please turn the power off, and allow the unit to cool down at least 20 minutes. After the projector has sufficiently cooled down, please make confirmation of the following items, and then turn the power on again.

• Is there blockage of the air passage aperture?

• Is the air filter dirty?

• Does the peripheral temperature exceed 35°C? If the same indication is displayed after the treatment, please change the lamp by referring to the section “Lamp”.

(continued)

Description

Lighting

in Green

Lighting

in Green

Alternative

Blinking in Red

Simultaneous

Blinking in Red

There is a possibility that the interior portion has become overcooled.

Please use the unit within the usage temperature parameters (0°C to 35°C). After the treatment, resent the power to ON.

It is time to clean the air filter, or there is no air filter.

Please immediately turn the power OFF, and clean or change the air filter by referring to the section “Air Filter”. After cleaning or changed the lamp, please be sure to reset the filter timer. After the treatment, resent the power to ON.

Page 46

roubleshooting (continued)

TTroubleshooting (continued)

Phenomena That May Easily Be Mistaken For Machine Defects

WARNING • Never use the projector if abnormal operations such as smoke,

strange odor, excessive sound, damaged casing or elements or cables, penetration of liquids or foreign matter, etc. should occur. In such cases, immediately turn off the power switch and then disconnect the power plug from the power outlet After making sure that the smoke or odor has stopped, contact your dealer or service company.

Before requesting repair, please check in accordance with the following chart. If the situation cannot be corrected, please contact your dealer or service company.

NOTE

• Although bright spots or dark spots may appear on the screen, this is a unique characteristic of liquid crystal displays, and such do not constitute or imply a machine defect.

Phenomenon Cases not involving a machine defect

The electrical power cord is not plugged in.

Correctly connect the power cord.

The power switch is not set to the on position.

Set the power switch to [ | ] (On).

The main power source has been interrupted during operation such as by a power outage (blackout), etc.

Power does not come on.

Neither sounds nor pictures are outputted.

Please turn the power off, and allow the unit to cool down at least 20 minutes. After the projector has sufficiently cooled down, please turn the power on again.

Either there is no lamp and/or lamp cover, or either of these has not been properly fixed.

The signal cables are not correctly connected.

Correctly connect the connection cables.

Signal source does not correctly work.

Correctly set up the signal source device by referring to the manual of the source device.

The input changeover settings are mismatched.

Select the input signal, and correct the settings.

(This table is continued to the following page.)

Reference

35, 36

pages

8, 9

Page 47

roubleshooting (continued)

TTroubleshooting (continued)

Phenomena That May Easily Be Mistaken For Machine Defects

Phenomenon Cases not involving a machine defect

The signal cables are not correctly connected.

Correctly connect the connection cables.

Pictures are displayed, but no sounds are heard.

Sounds are heard, but no pictures are displayed.

Colors have a faded- out appearance, or Color tone is poor.

Pictures appear dark.

Pictures appear blurry.

Input signal changes with no operation.

The volume is adjusted to an extremely low level.

Adjust the VOLUME to a higher level.

The sound is muted.

Press the MUTE button to restore the sound.

The audio input is not correctly selected when the child window is displayed.

Correctly select the audio input.

The lens cap is attached.

Remove the lens cap.

The signal cables are not correctly connected.

Correctly connect the connection cables.

The brightness is adjusted to an extremely low level.

Adjust the BRIGHT to a higher level using the menu function.

The screen is blanked.

Press the BLANK button to return to the input signal screen.

Color settings are not correctly adjusted.

Perform picture adjustments by changing the COLOR BAL R, COLOR BAL G, COLOR BAL B, COLOR and/or TINT settings, using the menu functions.

The brightness and/or contrast are adjusted to an extremely low level.

Adjust the BRIGHT and/or CONTRAST settings to a higher level using the menu function.

The WHISPER function is working.

Select the NORMAL to the item WHISPER in the MAIN menu.

The lamp is approaching the end of its product lifetime.

Replace the lamp.

Either the focus and/or horizontal phase settings are not properly.

Adjust the focus using the focus buttons, and/or H PHASE using the menu function.

The lens is dirty or misty.

Clean the lens by referring to the section “Caring For The Lens”.

The INPUT dial is set between the click points.

Turn the INPUT dial and set it at a click point.

(continued)

Reference

19, 32

35, 36

pages

8, 9

4, 15

8, 9

Page 48

arranty And After-Service

WWarranty And After-Service

If a problem occurs with the equipment, first refer to the “Troubleshooting” and run through the suggested checks. If this does not resolve the problem, please contact your dealer or service company. They will tell you what warranty condition is applied.

Specifications

NOTE

• This specifications are subject to change without notice.

Item Specification

Product name Liquid crystal projector Liquid

crystal panel

Lens Zoom lens F=1.7 ~ 2.4 f=30.5 ~ 45.8 mm Lamp 310W UHB Speaker 1.0W + 1.0W (Stereo) Power supply AC100 ~ 120V, 5.2A / AC220 ~ 240V, 2.2A Power consumption 470W Temperature range 0 ~ 35°C (Operating)

Size

Weight (mass) 7.7 kg

Ports

Optional Parts

Panel size 2.5 cm (0.99 type) Drive system TFT active matrix Pixels 786,432 pixels (1024 horizontal x 768 vertical)

420 (W) x 150 (H) x 310 (D) mm (Not including protruding parts)

• Please refer to the figure of the section “TECHNICAL” of the end of this manual.

RGB input ports

RGB M1-D BNC (R, G, B, H, V)

Video input ports

VIDEO IN S-VIDEO COMPONENT (C

R/PR, CB/PB, Y)

Audio input ports

AUDIO IN 1 AUDIO IN 2 AUDIO IN R/L

Lamp DT00601 Air filter NJ08081 Others • Please consult your dealer.

RGB output port

RGB OUT

Audio output port

AUDIO OUT

Control port

CONTROL

Other ports

NETWORK REMOTE CONTROL DC OUT