BOXLIGHT MP-25t User Manual

USER’S GUIDE

BOXLIGHT MP-25t

– 2 –

TO THE OWNER

As the owner of the Boxlight MP-25t, you are probably eager to try out your new projector. Before you do, we suggest that
you spend a little time reading this guide to familiarize yourself with the operating procedures, so that you will receive
maximum satisfaction from the many features included in your new projector.
This user’s guide will acquaint you with your projector’s features. Reading it will help us too. Through the years, we have
found that many service requests were not caused by problems with our projectors. They were caused by problems that
could have been prevented, if the owner had followed the instructions in the guide.
You can often correct operating problems yourself. If your projector fails to work properly, see “TROUBLESHOOTING”
section on pages 49 ~ 50 and try the solutions marked for each problem.

SAFETY PRECAUTIONS

WARNING:
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

This Boxlight MP-25t has a grounding-type AC line plug. This is a safety feature to be sure that the plug will fit into
the power outlet. Do not try to defeat this safety feature.

Intense light source. Do not stare directly into the projection lens as possible eye damage could result.
Be especially careful that children do not stare directly into the beam.

If the Projector will not be used for an extended time, unplug the new Projector from the power outlet.

READ AND KEEP THIS USER’S GUIDE FOR LATER USE.

INFORMATION TO THE USER

NOTE : This equipment has been tested and found to comply with the limits for a Class A digital device,

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the user’s guide, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case
the user will be required to correct the interference at his own expense.

CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO

USER-SERVICEABLE PARTS INSIDE EXCEPT LAMP REPLACEMENT. REFER SERVICING
TO QUALIFIED SERVICE PERSONNEL.

THIS SYMBOL INDICATES THAT
DANGEROUS VOLTAGE CONSTITUTING
A RISK OF ELECTRIC SHOCK IS
PRESENT WITHIN THIS UNIT.

THIS SYMBOL INDICATES THAT THERE
ARE IMPORTANT OPERATING AND
MAINTENANCE INSTRUCTIONS IN THE
USER’S GUIDE WITH THIS UNIT.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

– 3 –

IMPORTANT SAFETY INSTRUCTIONS

All the safety and operating instructions should be read
before the product is operated.

Read all of the instructions given here and retain them for
later use. Unplug this projector from AC power supply
before cleaning. Do not use liquid or aerosol cleaners. Use
a damp cloth for cleaning.

Do not use attachments not recommended by the
manufacturer as they may cause hazards.

Do not place this projector on an unstable cart, stand, or
table. The projector may fall, causing serious injury to a
child or adult, and serious damage to the projector. Use
only with a cart or stand recommended by the
manufacturer, or sold with the projector. Wall or shelf
mounting should follow the manufacturer’s instructions,
and should use a mounting kit approved by the
manufacturer.

Do not expose this unit to rain or use near water... for
example, in a wet basement, near a swimming pool, etc...

Slots and openings in the back and bottom of the cabinet
are provided for ventilation, to insure reliable operation of
the equipment and to protect it from overheating.

The openings should never be covered with cloth or other
material, and the bottom opening should not be blocked by
placing the projector on a bed, sofa, rug, or other similar
surface. This projector should never be placed near or
over a radiator or heat register.

This projector should not be placed in a built-in installation
such as a bookcase unless proper ventilation is provided.

This projector should be operated only from the type of
power source indicated on the marking label. If you are not
sure of the type of power supplied, consult your authorized
dealer or local power company.

Do not overload wall outlets and extension cords as this
can result in fire or electric shock. Do not allow anything to
rest on the power cord. Do not locate this projector where
the cord may be damaged by persons walking on it.

Never push objects of any kind into this projector through
cabinet slots as they may touch dangerous voltage points
or short out parts that could result in a fire or electric
shock. Never spill liquid of any kind on the projector.

Do not attempt to service this projector yourself as opening
or removing covers may expose you to dangerous voltage
or other hazards. Refer all servicing to qualified service
personnel.

Unplug this projector from wall outlet and refer servicing to
qualified service personnel under the following conditions:

a. When the power cord or plug is damaged or frayed.
b. If liquid has been spilled into the projector.
c. If the projector has been exposed to rain or water.
d. If the projector does not operate normally by following the

operating instructions. Adjust only those controls that are
covered by the operating instructions as improper
adjustment of other controls may result in damage and
will often require extensive work by a qualified technician
to restore the projector to normal operation.

e. If the projector has been dropped or the cabinet has been

damaged.

f. When the projector exhibits a distinct change in

performance-this indicates a need for service.

When replacement parts are required, be sure the service
technician has used replacement parts specified by the
manufacturer that have the same characteristics as the
original part. Unauthorized substitutions may result in fire,
electric shock, or injury to persons.

Upon completion of any service or repairs to this projector,
ask the service technician to perform routine safety checks
to determine that the projector is in safe operating condition.

This projector is equipped with a
grounding type AC line plug. Should
you be unable to insert the plug into
the outlet, contact your electrician.
Do not defeat the safety purpose of
this grounding type plug.

Follow all warnings and instructions marked on the
projectors.

For added protection to the projector during a lightning
storm, or when it is left unattended and unused for long
periods of time, unplug it from the wall outlet. This will
prevent damage due to lightning and powerline surges.

An appliance and cart combination
should be moved with care. Quick
stops, excessive force, and uneven
surfaces may cause the appliance
and cart combination to overturn.

If the projector is to be built into a compartment or similarly
enclosed, the minimum distances must be maintained.
Do not cover the ventilation slot on the projector.
Heat build-up can reduce the service life of your projector,
and can also be dangerous.

PROJECTOR

(FRONT)

PROJECTOR

(SIDE)

WALL

50cm

20cm

50cm

50cm

GROUND

– 4 –

TABLE OF CONTENTS

PAGEPAGE

INTRODUCTION 5

COMPATIBILITY 5
IMAGE RESOLUTION 5
PORTABILITY 5
UNPACKING THE PROJECTOR 5
TRADEMARKS 5

POWER REQUIREMENT 6
DESCRIPTION 7
SETTING-UP THE PROJECTOR 8-9

POSITIONING 8
ROOM LIGHT 8
VENTILATION 8
ADJUSTABLE FEET 9

MOVING THE PROJECTOR 9
CONNECTING THE PROJECTOR 10-17

CONNECTING THE COMPUTER 10-14
Connecting an IBM-compatible desktop computer 11
Connecting a Macintosh desktop computer 12
Connecting an IBM-compatible laptop computer 13
Connecting a Macintosh PowerBook computer 14
CONNECTING THE VIDEO EQUIPMENT 15-16
CONNECTING AN EXTERNAL SPEAKER 17

OPERATION OF CONTROLS 18-20

TOP OF THE PROJECTOR 18-19
REAR OF THE PROJECTOR 20

OPERATION OF REMOTE CONTROL 21-23

REMOTE CONTROL BATTERY INSTALLATION 23
USING THE REMOTE CONTROL UNIT 23

CONTROL THE PROJECTOR 24-26

DIRECT OPERATION 24
MENU OPERATION 25-26

USING THE PROJECTOR 27-46

TO TURN ON THE PROJECTOR 27
TO TURN OFF THE PROJECTOR 27
DIRECT OPERATION 27

MODE SELECT 27
SOUND VOLUME ADJUSTMENT 28

SOUND MUTE FUNCTION 28
ZOOM ADJUSTMENT 28
FOCUS ADJUSTMENT 28
DIGITAL ZOOM ADJUSTMENT 28
NORMAL PICTURE FUNCTION 28
NO SHOW FUNCTION 28
P-TIMER FUNCTION 28
FREEZE PICTURE FUNCTION 28
AUTO IMAGE FUNCTION 28

MENU OPERATION 29-46

MODE SELECT 29
SOUND ADJUSTMENT 30
LANGUAGE ADJUSTMENT 30
COLOR SYSTEM SELECT 31
PICTURE IMAGE ADJUSTMENT 32
PICTURE SCREEN ADJUSTMENT 33
COMPUTER SYSTEM SELECT 34
COMPATIBLE COMPUTER SPECIFICATION 35
AUTO IMAGE FUNCTION 36
PICTURE IMAGE ADJUSTMENT 37
PICTURE POSITION ADJUSTMENT 38
PC ADJUSTMENT 39-42
PICTURE SCREEN ADJUSTMENT 43
OTHER FUNCTION SETTING 44-46
BLUE BACK 44-45
DISPLAY 44-45
CEILING 44-45
REAR 44-45
SPLIT WIPE 44-45
LAMP AGE 46

AIR FILTER CARE AND CLEANING 47
TEMPERATURE WARNING INDICATOR 47
LAMP REPLACEMENT 48
CLEANING THE LENS 49
TROUBLESHOOTING 49-50
SERVICE 50
TECHNICAL SPECIFICATIONS 51
WARRANTY 52

– 5 –

INTRODUCTION

The projector is a multimedia projector designed for portability, durability, and ease of use. The projector utilizes built-in
multimedia features, a palette of 16.77 million colors, and active matrix liquid crystal display (LCD) technology.

The projector is compatible with many different types of personal computers and video devices, including;

¡IBM-compatible computers, including laptops, up to 1024 x 768 resolution.
¡Apple Macintosh and PowerBook computers up to 1024 x 768 resolution.
¡Various VCRs, video disc players, video cameras, DVD players, satellite TV tuners or other AV equipment using any of the

worldwide video standards, including NTSC, NTSC4.43, PAL, SECAM and PAL-M.

The resolution of the projector’s projected image is 800 x 600. The projector displays computer images just as they appear on
your computer’s monitor. Screen resolutions between 800 x 600 and 1024 x 768 are compressed to 800 x 600. The projector
cannot display screen resolutions above 1024 x 768. If your computer’s screen resolution is higher than 1024 x 768, reset it
to a lower resolution before you connect the projector.

The projector is extremely compact in size and weight. Having a sophisticated shape like an attach‹G case with a retractable
carrying handle, the projector will help you make powerful presentations wherever you go.

The projector comes with the parts listed below. Check to make sure all are included. If any parts are missing, contact an
authorized dealer or service station.

¡User’s guide.
¡AC Power Cord.
¡Remote Control Transmitter Unit and batteries.
¡Lens Cover.
¡Protective Dust Cover.
¡VGA Cable.
¡Mouse Cable for PS/2 port.

¡Apple, Macintosh, and PowerBook are trademarks or registered trademarks of Apple Computer, Inc.
¡IBM and PS/2 are trademarks or registered trademarks of International Business Machines, Inc.

TRADEMARKS

UNPACKING THE PROJECTOR

PORTABILITY

IMAGE RESOLUTION

COMPATIBILITY

– 6 –

POWER REQUIREMENTS

Your projector uses nominal input voltages of 100-120 VAC or
200-240 VAC. The projector automatically selects the correct
input voltage. The projector is designed to work with single-phase
power systems having a grounded neutral conductor. To reduce
the risk of electrical shock, do not plug into any other type of
power system.
Consult your authorized dealer or service station if you are not
sure what type of power is supplied to your building.

Connect the AC power
supply cord (supplied)
to the projector.

Projector side (Female) AC outlet side (Male)

– 7 –

DESCRIPTION

SPEAKERS

INFRARED
REMOTE
RECEIVER

PROJECTION LENS

FEET LOCK BUTTON

FEET LOCK
BUTTON

REMOVABLE
LENS COVER

INFRARED
REMOTE
RECEIVER

MAIN ON/OFF
SWITCH

CARRYING
HANDLE

POWER CORD
CONNECTOR

LAMP COVER

ADJUSTABLE
FEET

AIR INTAKE VENT

AIR INTAKE
VENT

FRONT

REAR

EXHAUST VENT

CAUTION HOT AIR !
Air blown from the exhaust vent is hot.
Observe the following when handling your
projector or choosing a location to install it.

¡Keep heat-sensitive objects away from the

exhaust port.

¡If you set the projector on top of a metallic

surface, the surface will become hot because
of the hot air exhaust. Be careful when
handling.

¡Do not touch the cabinet near to the exhaust

vent area, and especially screws and metallic
parts. These parts will become hot while the
projector is used.

BOTTOM

AIR INTAKE VENT
(BOTTOM SIDE)

EXHAUST VENT
(REAR SIDE)

VENTILATION

This projector is equipped with a cooling fan to protect it from
overheating. Pay attention to the following to ensure the ventilation
and avoid a possible risk of fire and malfunction.

¡Do not cover the vents with papers or other materials.
¡Keep the rear grill at least 3.3’ (1m) away from any

object.

¡Make sure that there are no objects under the projector.

An object under the projector may prevent the projector
from taking the cooling air through the bottom vent.

– 8 –

SETTING-UP THE PROJECTOR

40"
(101.6 cm)

60"
(152.4 cm)

100"
(254 cm)

150"
(381 cm)

200"
(508 cm)

250"
(635 cm)

192"
(487.7 cm)

154"
(391.2 cm)

115"
(292.1 cm)

77"
(195.6 cm)

46"
(116.8 cm)

30"
(76.2 cm)

300"
(762 cm)

231"
(586.7 cm)

H1

H2

Maximum Zoom

Minimum Zoom

DISTANCE

Ideally the projector should be placed in a
room with limited light. Picture quality will
be directly affected by lighting conditions.

POSITIONING:

ROOM LIGHT

¡This projector is basically designed to project on a flat projection surface.
¡This projector can be focused from 4.6’ (1.4 m) ~ 35.4’ (10.8 m).
¡Use the illustration below as an example when positioning

the projector to the screen.

Screen Size

Max. Zoom

Min. Zoom

Distance

101.6 cm

76.2 cm

1.4 m

152.4 cm

116.8 cm

2.2 m

254 cm

195.6 cm

3.6 m

381 cm

292.1 cm

5.4 m

508 cm

391.2 cm

7.2 m

635 cm

487.7 cm

9.0 m

762 cm

586.7 cm

10.8 m

Screen Size

Max. Zoom

Min. Zoom

Distance

40"
30"

4.6’

60"
46"

7.2’

100"

77"

11.8’

150"
115"

17.7’

200"
154"

23.6’

250"
192"

29.5’

300"
231"

35.4’

Screen Size
(W x H) inch

Height (H1)
Height (H2)

30"

24 x 18

17.1 inch

0.9 inch

60"

48 x 36

34.2 inch

1.8 inch

100"
80 x 60
57 inch

3 inch

150"

120 x 90

85.5 inch

4.5 inch

200"

160 x 120

114 inch

6 inch

250"

200 x 150

142.5 inch

7.5 inch

300"

240 x 180

171 inch

9 inch

Screen Size

(W x H) cm

Height (H1)
Height (H2)

76.2 cm

60.9 x 45.7

43.4 cm

2.3 cm

152.4 cm

121.9 x 91.4

86.9 cm

4.6 cm

254 cm

203.2 x 152.4

144.8 cm

7.6 cm

381 cm

304.8 x 228.6

217.2 cm

11.4 cm

508 cm

406.4 x 304.8

289.6 cm

15.2 cm

635 cm

508 x 381

361.9 cm

19.1 cm

762 cm

609.6 x 457.2

434.3 cm

22.9 cm

Use the carrying handle when moving the projector.

Replace the lens cover and retract the adjustable feet
when moving the projector to prevent damage to the
projector.

– 9 –

ADJUSTABLE FEET

Picture tilt and projection angle can be adjusted by ADJUSTABLE
FEET. Projection angle can be adjusted 0 to 6°.

1. Lift the front of the projector and press the feet lock buttons (left
and right) under the sides of the projector.
When the buttons are pressed, feet lock is released.

2. Release the buttons at desired front height position. (feet is
locked).

3. Turn the adjustable feet and adjust picture position and tilt.

UP

UP

DOWN

DOWN

ADJUSTABLE FEET

FEET LOCK BUTTONS

CAUTION IN CARRYING OR TRANSPORTING THE PROJECTOR

¡ Do not drop or bump the projector, otherwise damages or malfunctions may result.
¡ When transporting the projector, use a Boxlight recommended Carrying Case.
¡ Do not transport the projector by using a courier or transport service in an unsuitable transport case. This may cause

damage to the projector. To transport the projector through a courier or transport service, use a Boxlight
recommended Case.

¡ For a carrying or transportation cases, contact a Boxlight at 1-800-762-5757 or 360-779-7901.

MOVING THE PROJECTOR

– 10 –

CONNECTING THE PROJECTOR

Your projector is equipped with various audio/video inputs and outputs including Computer HDB15-pin (VGA) terminals,
Monitor HDB15-pin (VGA) terminals and S-VHS video.

* NOTE: The RxD port (5 pin on the Serial Port) is provided on control port 2 connector only. If you control the projector by

computer, you must connect control port 2 connector.

CONNECTING THE COMPUTER

CONNECTING TO THE COMPUTER INPUT HDB15-PIN (VGA) TERMINALS (1 and 2)

Personal computers can be connected to the HDB15-pin (VGA) terminal on the projector.
¡Connect the computer to these terminals using the VGA cable and VGA/MAC adapter (not provided).

WARNING: For projectors, the VGA cable provided is designed to reduce RFI (Radio Frequency Interference) emissions.

For regulatory compliance reasons, this cable must be used and must not be replaced by any other cable.

CONNECTING TO THE MONITOR OUTPUT HDB15-PIN (V

GA) TERMINAL

This terminal contains the information that is viewed on the screen.
An external monitor can be connected to the HDB15-pin (VGA) terminal on the projector.

¡Connect the monitor to this terminal using a monitor cable (not provided).

CONNECTING TO THE COMPUTER AUDIO INPUT JACKS (1 and 2)

¡Connect audio outputs from your computer to these jacks using the audio cable (not provided).

CONNECTING TO THE MULTI-POLE 12-PIN (CONTROL PORT) CONNECTORS (1 and 2)

¡If you wish to control the computer with projector’s remote control unit, you must connect the control port on your

computer to the projector’s control port with the control cable for PS/2 port (provided).

54321

109876

15 14 13 12 11

HDB15-PIN
TERMINAL

Pin No./Signal

1 Red input
2 Green input
3 Blue input
4 Sense 2
5 Ground (Horiz. sync.)
6 Ground (Red)
7 Ground (Green)
8 Ground (Blue)

Pin No./Signal

9 Non Connect
10 Ground (Vert. sync.)
11 Sense 0
12 Sense 1
13 Horiz. sync.
14 Vert. sync.
15 Reserved

■ CONTROL PORT

1

4

3

7

8

11

12

9

10

2

5

6

AA

B

CONTROL PORT CABLE
REMOVAL HINT

Disconnect control port cable
with following steps.

1. Hold the portion (A) of the
connector with one hand.

2. Pull the portion (B) arrow
direction and remove
connector.

PS/2-port

––––––––

CLK

DATA

––––––––
––––––––
––––––––
––––––––
––––––––

GND

––––––––
––––––––
––––––––

TxD

––––––––
––––––––
––––––––

*RxD

––––––––

READY

––––––––

GND

––––––––
––––––––
––––––––

––––––––

ADB

––––––––
––––––––
––––––––
––––––––
––––––––
––––––––

GND

––––––––
––––––––
––––––––

1
2
3
4
5
6
7
8

9
10
11
12

Serial Port ADB Port

– 11 –

Connecting an IBM-compatible desktop computer

NOTE: The hook up should be done as per the above illustration. After hook up, turn on the projector, monitor, computer, in

that order.

AV IN

AUDIO

VIDEO VIDEO

S-VIDEO

(MONO)

MONITOR OUT

R L

AUDIO

R L

COMPUTER IN 1 COMPUTER IN 2

MONITOR OUT

EXT. SPCONTROL PORT 2CONTROL PORT 1 AUDIO 2

(STEREO)(STEREO)

AUDIO 1

(STEREO)

(8Ω)

COMPUTER

MONITOR CABLE
(NOT PROVIDED)

COMPUTER
OUTPUT

AUDIO
OUTPUT

SERIAL PORT
INPUT

AUDIO CABLE
(NOT PROVIDED)

COMPUTER
AUDIO INPUT
1 or 2

CONTROL PORT
OUTPUT 1 or 2

MOUSE CABLE
FOR PS/2 PORT
(PROVIDED)

MOUSE CABLE
FOR SERIAL PORT
(NOT PROVIDED)

PS/2
PORT INPUT

COMPUTER
INPUT 1 or 2

VGA CABLE
(PROVIDED)

MONITOR
OUTPUT

AUDIO
INPUT

Amp.

LR

R

L

Speaker (L) Speaker (R)

SPEAKER
OUT

AUDIO MONITOR
OUTPUT

AV IN

AUDIO

VIDEO VIDEO

S-VIDEO

(MONO)

MONITOR OUT

R L

AUDIO

R L

COMPUTER IN 1 COMPUTER IN 2

MONITOR OUT

EXT. SPCONTROL PORT 2CONTROL PORT 1 AUDIO 2

(STEREO)(STEREO)

AUDIO 1

(STEREO)

(8Ω)

123456

ON

– 12 –

Connecting a Macintosh desktop computer

NOTE: The hook up should be done as per the above illustration. After hook up, turn on the projector, monitor, computer, in

that order.

CONTROL PORT
OUTPUT 1 or 2

COMPUTER

MONITOR CABLE
(NOT PROVIDED)

COMPUTER
OUTPUT

AUDIO
OUTPUT

ADB
PORT INPUT

COMPUTER
AUDIO INPUT
1 or 2

AUDIO CABLE
(NOT PROVIDED)

MOUSE CABLE FOR
ADB PORT
(NOT PROVIDED)

COMPUTER
INPUT 1 or 2

MONITOR
OUTPUT

VGA/MAC ADAPTER
(NOT PROVIDED)

VGA CABLE
(PROVIDED)

Set the dip switches as shown in the table below depending on the
RESOLUTION MODE that you want to use before you turn on the
projector and computer.

12

ON

ON

OFF

DIP

3456

VGA/MAC ADAPTER

AUDIO
INPUT

Amp.

LR

R

L

Speaker (L) Speaker (R)

SPEAKER OUT

AUDIO MONITOR
OUTPUT

RESOLUTION MODE
13” MODE (640

x

480)
16” MODE (832x 624)
19” MODE (1024

x

768)

SW6
OFF
OFF
OFF

SW5

OFF
OFF
OFF

SW4
OFF

ON

OFF

SW3

OFF
OFF

ON

SW2

ON
ON
ON

SW1

ON
OFF
OFF

– 13 –

Connecting an IBM-compatible laptop computer

NOTE: The hook up should be done as per the above illustration. After hook up, turn on the projector, computer, in that

order.

AV IN

AUDIO

VIDEO VIDEO

S-VIDEO

(MONO)

MONITOR OUT

R L

AUDIO

R L

COMPUTER IN 1 COMPUTER IN 2

MONITOR OUT

EXT. SPCONTROL PORT 2CONTROL PORT 1 AUDIO 2

(STEREO)(STEREO)

AUDIO 1

(STEREO)

(8Ω)

CONTROL PORT
OUTPUT 1 or 2

COMPUTER

COMPUTER
OUTPUT

AUDIO
OUTPUT

SERIAL PORT
INPUT

PS/2
PORT INPUT

COMPUTER
INPUT 1 or 2

COMPUTER
AUDIO INPUT
1 or 2

AUDIO CABLE
(NOT PROVIDED)

VGA CABLE
(PROVIDED)

MOUSE CABLE
FOR PS/2 PORT
(PROVIDED)

MOUSE CABLE
FOR SERIAL PORT
(NOT PROVIDED)

AUDIO
INPUT

Amp.

LR

R

L

Speaker (L) Speaker (R)

SPEAKER OUT

AUDIO MONITOR
OUTPUT

– 14 –

Connecting a Macintosh PowerBook computer

AV IN

AUDIO

VIDEO VIDEO

S-VIDEO

(MONO)

MONITOR OUT

R L

AUDIO

R L

COMPUTER IN 1 COMPUTER IN 2

MONITOR OUT

EXT. SPCONTROL PORT 2CONTROL PORT 1 AUDIO 2

(STEREO)(STEREO)

AUDIO 1

(STEREO)

(8Ω)

123456

ON

NOTE: The hook up should be done as per the above illustration. After hook up, turn on the projector, computer, in that

order.

COMPUTER

AUDIO
OUTPUT

ADB PORT
INPUT

VGA/MAC ADAPTER
(NOT PROVIDED)

COMPUTER
INPUT 1 or 2

COMPUTER
AUDIO INPUT 1 or 2

AUDIO CABLE
(NOT PROVIDED)

VGA CABLE
(PROVIDED)

MOUSE CABLE
FOR ADB PORT
(NOT PROVIDED)

The Macintosh PowerBook requires the use of the
PowerBook Video Adapter shipped with the PowerBook.

TO POWERBOOK
VIDEO ADAPTER

CONTROL PORT
OUTPUT 1 or 2

12

ON

ON

OFF

DIP

3456

VGA/MAC ADAPTER

Set the dip switches as shown in the table below depending on the
RESOLUTION MODE that you want to use before you turn on the
projector and computer.

AUDIO
INPUT

Amp.

LR

R

L

Speaker (L) Speaker (R)

SPEAKER OUT

AUDIO MONITOR
OUTPUT

RESOLUTION MODE
13” MODE (640

x

480)
16” MODE (832x 624)
19” MODE (1024

x

768)

SW6
OFF
OFF
OFF

SW5

OFF
OFF
OFF

SW4
OFF

ON

OFF

SW3

OFF
OFF

ON

SW2

ON
ON
ON

SW1

ON
OFF
OFF

– 15 –

CONNECTING THE VIDEO EQUIPMENT

CONNECTING TO THE AV INPUT JACKS

Connect to the video and audio outputs of a VCR, video disc player, DVD player, video camera, satellite TV tuner or other
AV equipment.

¡Connect audio/video outputs from external sources to the input jacks using the audio/video cable.
¡If the audio signal from the AV equipment is stereo, be sure to connect the right and left channels to the respective right

and left audio input jacks.

¡If the external audio signal is monaural, connect it to the left jack.

S-VHS FORMAT VCR CONNECTION

The AV input includes an extra video input jack marked S-VIDEO to allow connection to an S-VHS format VCR that has
separate Y/C video signals. The S-VIDEO jack has priority over the VIDEO jack.

CONNECTING TO THE VIDEO MONITOR OUTPUT JACK

This jack will contain the video information of the selected program source video only. If you select program source
Computer 1 or Computer 2, there is no signal.
Connect video input from AV equipment to this jack by RCA cable.
Whenever the S-VIDEO signal source is viewed on the screen, the video signal available at the MONITOR OUTPUT jack
will be in black and white (monochrome).

CONNECTING T

O THE AUDIO MONITOR OUTPUT JACKS

These jacks will contain the audio information of the selected program source being viewed on the screen (Computer 1,
Computer 2 or Video 1). If you have selected program source Computer 1 the audio signal connected to the Computer 1
audio input jack will be available at the audio monitor output jacks.

¡If the audio input of the audio equipment is stereo, be sure to connect the right and left channels to the respective right

and left jacks.

¡If the audio input of the audio equipment is monaural, connect it to the left jack.

– 16 –

Connecting the Video Equipment

NOTE: The hook up should be done as per the above illustration. After hook up, turn on the projector, video equipment,

in that order.

AV IN

AUDIO

VIDEO VIDEO

S-VIDEO

(MONO)

MONITOR OUT

R L

AUDIO

R L

COMPUTER IN 1 COMPUTER IN 2

MONITOR OUT

EXT. SPCONTROL PORT 2CONTROL PORT 1 AUDIO 2

(STEREO)(STEREO)

AUDIO 1

(STEREO)

(8Ω)

VIDEO EQUIPMENT

Video Cassette Recorder

DVD Player
Video Disc Player

Satellite
TV Tuner

L R
AUDIO
OUTPUT

VIDEO
OUTPUT

VIDEO INPUT

VIDEO
INPUT

MONITOR

S-VHS-VCR
Etc...

S-VIDEO
INPUT

AUDIO
INPUT

AUDIO
OUTPUT

S-VIDEO
OUTPUT

AUDIO
INPUT

AUDIO INPUT

SPEAKER
OUT

AUDIO MONITOR
OUTPUT

VIDEO
MONITOR
OUTPUT

Amp.

LR

R

L

Speaker (L)

Speaker (R)

– 17 –

CONNECTING AN EXTERNAL SPEAKER

CONNECTING TO THE EXT. SP. JACK (3.5mm mini stereo type)

This jack outputs stereo speaker sound which viewing on screen. If you use external speaker system, connect stereo type
external speaker jack. Internal speaker sound is disconnected when speaker jack is connected.

COMPUTER IN 1 COMPUTER IN 2

MONITOR OUT

EXT. SPCONTROL PORT 2CONTROL PORT 1 AUDIO 2

(STEREO)(STEREO)

AUDIO 1

(STEREO)

(8Ω)

AV IN

AUDIO

VIDEO VIDEO

S-VIDEO

(MONO)

MONITOR OUT

R L

AUDIO

R L

EXTERNAL
SPEAKER SYSTEM

– 18 –

OPERATION OF CONTROLS

TOP CONTROLS

TOP CONTROLS

MODE

SELECT

AUTO IMAGE NORMAL

MENU

ZOOM FOCUS VOLUME

ON-OFF

!3

!1

o

!0

!2 i u

y

t

!4

TOP OF THE PROJECTOR

LAMP

REPLACE

LAMP

READY

WARNING

TEMP.

q

we

r

FRONT
INDICATORS

FRONT INDICATORS

– 19 –

q

LAMP REPLACEMENT INDICATOR

Light is orange when projection lamp is nearing end of service life.

w

TEMPERATURE WARNING INDICATOR

Flashes red when internal projector temperature is too high.

e

READY INDICATOR

Light is green when projector lamp is ready to be turned on.

r

LAMP POWER INDICATOR

Light is dim when the projector is on.
Light is brightened when the projector is in stand-by mode.

t

LAMP POWER ON/OFF BUTTON

Used to turn projection lamp on or off.

y

VOLUME BUTTONS

Used to adjust volume.

u

FOCUS BUTTONS

Used to operate power focus system.

i

ZOOM BUTTONS

Used to operate power zoom lens.

o

MODE BUTTON

Used to select source. (Computer 1, Computer 2 or Video 1 Input)

!0

MENU BUTTON

This button will activate the MENU operation.
Use this button, the POINT UP/DOWN/LEFT/RIGHT buttons and the SELECT button to make adjustments to the
projector’s setting in MENU operation.

!1

AUTO IMAGE BUTTON

Used to operate the AUTO IMAGE function.

!2

NORMAL BUTTON

Used to reset to normal picture adjustment preset by factory.

!3

POINT UP/DOWN/LEFT/RIGHT BUTTONS

To select an item on the MENU that you want to adjust. To select an item, move the arrow by pressing these buttons
(UP, DOWN, LEFT or RIGHT).

!4

SELECT BUTTON

This button has different functions depending on when used. This button is used to execute the item selected, to
increase or decrease the values in certain items such as CONTRAST or BRIGHTNESS.

– 20 –

!5

COMPUTER INPUT-1 TERMINAL

Used to connect a computer to the projector.

!6

COMPUTER INPUT-2 TERMINAL

Used to connect a computer to the projector.

!7

MONITOR OUTPUT TERMINAL

Used to connect a monitor to the projector.

!8

COMPUTER AUDIO INPUT-1 JACK
mini stereo type

Used to connect a computer audio input to the
projector.

!9

CONTROL PORT-1 CONNECTOR

Used to connect a mouse cable to the projector.

@0

COMPUTER AUDIO INPUT-2 JACK
mini stereo type

Used to connect a computer audio input to the
projector.

@1

CONTROL PORT-2 CONNECTOR (SERIAL PORT)

Used to connect a mouse cable to the projector.

NOTE: Control port-2 connector can be also used

as serial port.

@2

AUDIO INPUT JACKS

Used to connect an audio input to the projector.

@3

VIDEO INPUT JACK

Used to connect a video source to the projector.

@4

S-VIDEO INPUT JACK

Used to connect a S-VHS video source to the projector.

@5

AUDIO MONITOR OUTPUT JACKS

Permits audio connection to a monitor.

@6

VIDEO MONITOR OUTPUT JACK

Permits video connection to a monitor.

@7

EXT. SP. JACK (3.5 mm mini stereo type)

Used to connect an external speaker system.

COMPUTER IN 1 COMPUTER IN 2

MONITOR OUT

EXT. SPCONTROL PORT 2CONTROL PORT 1 AUDIO 2

(STEREO)(STEREO)

AUDIO 1

(STEREO)

(8Ω)

AV IN

AUDIO

VIDEO VIDEO

S-VIDEO

(MONO)

MONITOR OUT

R L

AUDIO

R L

!9

@2

!8

!5 !6 !7

@0
@1

@7

@3 @4

@5

@6

REAR OF THE PROJECTOR

– 21 –

P-TIMER

MENU

A

U

TO

IM

AG

E

MUTE

VOLUME

MODE

FO

C

U

S

ZOOM

FREEZE

NO

SHOW

D. ZO

O

M

w

i

o

!0
!3

!4

!1

e

q

yr

u

t

!2

!5

N

O

R

M

A

L

O

N-O

FF

!6

OPERATION OF REMOTE CONTROL

This remote control unit is not only able to operate the projector but also
usable as a wireless mouse for a PC. One pointing pad and two click buttons
are used for wireless mouse operation.
Wireless mouse is usable when PC mouse pointer is displayed on the
screen. When the menu or indicator of the projector is displayed on the
screen instead of the PC mouse pointer, the wireless mouse cannot be
used.

NOTE: To use the unit as a PC wireless mouse, connect the projector to the

PC with the attached cable. Signals from the projector are
transmitted to the PC, enabling the remote control unit of the
projector to be used as a PC wireless mouse. (Refer to
“CONNECTING THE PROJECTOR” in pages 10 to 14 for the
connection.)

FRONT SIDE

– 22 –

q

MODE BUTTON

Used to select source. (Computer 1, Computer 2 or Video 1 Input)

w

LAMP POWER ON/OFF BUTTON

Used to turn the projection lamp on or off.

e

VOLUME BUTTONS

Used to adjust volume.

r

ZOOM BUTTON

Used to select power zoom lens adjust.

t

P-TIMER BUTTON

Used to operate the P-TIMER function.

y

FOCUS BUTTON

Used to select focus adjust.

u

NO SHOW BUTTON

Used to change the screen into black image.

i

SOUND MUTE BUTTON

Used to mute sound.

o

D. ZOOM BUTTON

Used to select digital zoom function.

!0

FREEZE BUTTON

Use this button to freeze on-screen image.

!1

AUTO IMAGE BUTTON

Used to operate the AUTO IMAGE function.

!2

MENU BUTTON

This button will activate the MENU operation. Use this button, the POINT UP/DOWN/LEFT/RIGHT button and the
SELECT (REAR CLICK) button to make adjustments to the projector’s setting in MENU operation.

!3

NORMAL BUTTON

Use to reset to normal picture adjustment preset by factory.

!4

POINTING PAD (POINT UP/DOWN/LEFT/RIGHT BUTTON)
When in use as a remote for the projector.

To select an item on the MENU that you want to adjust. To select an item, move the arrow by pressing the pad upward,
downward, leftward or rightward.
Used to operate power zoom lens, power focus system or digital zoom function by pressing the pad either upward or
downward.

When in use as a wireless mouse

Used to move the pointer. The pointer is moved according to the direction you are pressing.

!5

FRONT CLICK BUTTON

This button has the same function as the right button in a PC mouse. Pressing this button does not affect any operation
when in MENU mode.

!6

SELECT (REAR CLICK) BUTTON
When in use as a remote for the projector.

This button has different functions depending on when used. This button is used to execute the item selected, to
increase or decrease the values in certain items such as CONTRAST or BRIGHTNESS.

When in use as a wireless mouse

This button has the same function as the left button in a PC mouse.

– 23 –

REMOTE CONTROL BATTERY INSTALLATION

1

Remove the battery

compartment lid. 2

Slide the batteries into the

compartment. 3

Replace the compart­ment lid.

Note: For correct polarity (+ and –

terminal), be sure the battery
terminals are in contact with
the pins in the compartment.

USING THE REMOTE CONTROL UNIT

Point the remote control toward the projector (Receiver window) whenever pressing the buttons. Maximum operating range
for the remote control is about 16.4’ (5m) and 60° front and rear of the projector.

To insure safe operation, please observe the following precautions:

¡Use (2) AA type alkaline batteries.
¡Change two batteries at the same time.
¡Do not use a new battery with a used battery.
¡Avoid contact with water.
¡Do not drop the remote control unit.
¡If batteries have leaked on the remote control, carefully wipe the case clean and load new

batteries.

16.4’
(5 m)

16.4’
(5 m)

60°

60°

– 24 –

CONTROL THE PROJECTOR

The projector has two types of operation: DIRECT OPERATION and MENU OPERATION. DIRECT OPERATION allows you
to operate the projector by using one button without showing the MENU. In MENU OPERATION mode, you display menus
where you can adjust the projector’s settings. Follow the instruction for each control.

DIRECT OPERATION

ADJUST ITEM

LAMP POWER ON/OFF LAMP POWER ON-OFF BUTTON LAMP POWER ON-OFF BUTTON
MODE SELECT

MODE BUTTON

MODE BUTTON

SOUND VOLUME VOLUME (+) and (–) BUTTONS VOLUME (+) and (–) BUTTONS
SOUND MUTE NOT AVAILABLE MUTE BUTTON
ZOOM

ZOOM ( ) and ( ) BUTTONS

ZOOM BUTTON
POINT (UP/DOWN) BUTTON

FOCUS

FOCUS ( ) and ( ) BUTTONS

FOCUS BUTTON
POINT (UP/DOWN) BUTTON

DIGITAL ZOOM NOT AVAILABLE

D. ZOOM BUTTON
SELECT (REAR CLICK) BUTTON
FRONT CLICK BUTTON
POINT (UP/DOWN/LEFT/RIGHT)
BUTTON

NORMAL PICTURE NORMAL BUTTON NORMAL BUTTON
NO SHOW NOT AVAILABLE NO SHOW BUTTON
P. TIMER NOT AVAILABLE P-TIMER BUTTON
FREEZE PICTURE NOT AVAILABLE FREEZE BUTTON
AUTO IMAGE AUTO IMAGE BUTTON AUTO IMAGE BUTTON

TOP CONTROL
OF THE PROJECTOR

REMOTE CONTROL UNIT

– 25 –

ADJUST ITEM

SOUND

SOUND VOLUME
SOUND MUTE

MENU BUTTON
POINT LEFT/RIGHT BUTTONS
SELECT BUTTON
POINT UP/DOWN BUTTONS
SELECT BUTTON

MENU BUTTON
POINT (LEFT/RIGHT) BUTTON
SELECT (REAR CLICK) BUTTON
POINT (UP/DOWN) BUTTON
SELECT (REAR CLICK) BUTTON

MENU BUTTON
POINT LEFT/RIGHT BUTTONS
SELECT BUTTON
POINT UP/DOWN BUTTONS
SELECT BUTTON

MENU BUTTON
POINT (LEFT/RIGHT) BUTTON
SELECT (REAR CLICK) BUTTON
POINT (UP/DOWN) BUTTON
SELECT (REAR CLICK) BUTTON

LANGUAGE
SETTING

BLUE BACK
DISPLAY
CEILING
REAR
SPLIT WIPE
LAMP AGE

TOP CONTROL
OF THE PROJECTOR

REMOTE CONTROL UNIT

1. COMPUTER/VIDEO MODE

ADJUST ITEM

COLOR SYSTEM

MENU BUTTON
POINT LEFT/RIGHT BUTTONS
SELECT BUTTON
POINT UP/DOWN BUTTONS
SELECT BUTTON

MENU BUTTON
POINT (LEFT/RIGHT) BUTTON
SELECT (REAR CLICK) BUTTON
POINT (UP/DOWN) BUTTON
SELECT (REAR CLICK) BUTTON

MENU BUTTON
POINT LEFT/RIGHT BUTTONS
SELECT BUTTON
POINT UP/DOWN BUTTONS
SELECT BUTTON

MENU BUTTON
POINT (LEFT/RIGHT) BUTTON
SELECT (REAR CLICK) BUTTON
POINT (UP/DOWN) BUTTON
SELECT (REAR CLICK) BUTTON

PICTURE IMAGE

COLOR
TINT
CONTRAST
BRIGHTNESS
SHARPNESS

PICTURE SCREEN

WIDE
REGULAR

TOP CONTROL
OF THE PROJECTOR

REMOTE CONTROL UNIT

2. VIDEO MODE

MENU OPERATION

ADJUST ITEM

MODE SELECT

MENU BUTTON
POINT LEFT/RIGHT BUTTONS
SELECT BUTTON
POINT UP/DOWN BUTTONS
SELECT BUTTON

MENU BUTTON
POINT (LEFT/RIGHT) BUTTON
SELECT (REAR CLICK) BUTTON
POINT (UP/DOWN) BUTTON
SELECT (REAR CLICK) BUTTON

TOP CONTROL
OF THE PROJECTOR

REMOTE CONTROL UNIT

– 26 –

ADJUST ITEM

COMPUTER SYSTEM

MENU BUTTON
POINT LEFT/RIGHT BUTTONS
SELECT BUTTON
POINT UP/DOWN BUTTONS
SELECT BUTTON

MENU BUTTON
POINT (LEFT/RIGHT) BUTTON
SELECT (REAR CLICK) BUTTON
POINT (UP/DOWN) BUTTON
SELECT (REAR CLICK) BUTTON

TOP CONTROL
OF THE PROJECTOR

REMOTE CONTROL UNIT

3. COMPUTER MODE

AUTO IMAGE

FINE SYNC
TOTAL DOTS
POSITION

MENU BUTTON
POINT LEFT/RIGHT BUTTONS
SELECT BUTTON
POINT UP/DOWN BUTTONS
SELECT BUTTON

MENU BUTTON
POINT (LEFT/RIGHT) BUTTON
SELECT (REAR CLICK) BUTTON
POINT (UP/DOWN) BUTTON
SELECT (REAR CLICK) BUTTON

PICTURE IMAGE

FINE SYNC
TOTAL DOTS
WHITE BALANCE
CONTRAST
BRIGHTNESS

MENU BUTTON
POINT LEFT/RIGHT BUTTONS
SELECT BUTTON
POINT UP/DOWN BUTTONS
SELECT BUTTON

MENU BUTTON
POINT (LEFT/RIGHT) BUTTON
SELECT (REAR CLICK) BUTTON
POINT (UP/DOWN) BUTTON
SELECT (REAR CLICK) BUTTON

PICTURE POSITION

MENU BUTTON
POINT LEFT/RIGHT BUTTONS
SELECT BUTTON
POINT LEFT/RIGHT/UP/DOWN
BUTTONS
SELECT BUTTON

MENU BUTTON
POINT (LEFT/RIGHT) BUTTON
SELECT (REAR CLICK) BUTTON
POINT (LEFT/RIGHT/UP/DOWN)
BUTTON
SELECT (REAR CLICK) BUTTON

PC ADJUSTMENT MENU BUTTON

POINT LEFT/RIGHT BUTTONS
SELECT BUTTON
POINT UP/DOWN BUTTONS
SELECT BUTTON

MENU BUTTON
POINT (LEFT/RIGHT) BUTTON
SELECT (REAR CLICK) BUTTON
POINT (UP/DOWN) BUTTON
SELECT (REAR CLICK) BUTTON

PICTURE SCREEN

TRUE
DIGITAL ZOOM

MENU BUTTON
POINT LEFT/RIGHT BUTTONS
SELECT BUTTON
POINT UP/DOWN BUTTONS
SELECT BUTTON
POINT LEFT/RIGHT/UP/DOWN
BUTTONS

MENU BUTTON
POINT (LEFT/RIGHT) BUTTON
SELECT (REAR CLICK) BUTTON
POINT (UP/DOWN) BUTTON
SELECT (REAR CLICK) BUTTON
SELECT (REAR CLICK) BUTTON
FRONT CLICK BUTTON
POINT (UP/DOWN/LEFT/RIGHT)
BUTTON

NOTES:

1. If you switch to DIRECT operation by pressing a DIRECT operation button while in MENU mode, the menus will
disappear and the MENU operation will end.

2. You can use the REMOTE CONTROL UNIT or the TOP CONTROL OF THE PROJECTOR to operate the MENU
operation.

– 27 –

Connect the projector to a source (Computer, VCR, Video Camera, Video Disc Player, etc.) using the appropriate terminals
on the rear of the projector (See “CONNECTING THE PROJECTOR” section on pages 10-17).

Connect the projector’s AC power cord into a wall outlet and turn the MAIN ON/OFF switch (located on the rear of the
projector) to the ON position. The LAMP POWER indicator will light RED, the READY indicator will light GREEN.

Press the LAMP POWER ON/OFF button on the remote control unit or on the
projector to ON. The LAMP POWER indicator light will dim and the cooling fans will
operate. The wait display appears on the screen and the count-down starts (20-19­18-...1). The signal from the source appears after 30 seconds.

20

USING THE PROJECTOR

TO TURN ON THE PROJECTOR

TO TURN OFF THE PROJECTOR

CAUTION:
TO MAINTAIN THE LIFE OF THE LAMP, ONCE YOU HAVE TURNED IT ON, WAIT AT LEAST 5 MINUTES
BEFORE TURNING IT OFF.

NOTE: TEMPERATURE WARNING INDICATOR flashes red, the projector will automatically turn off.

Wait at least 5 minutes before turning the projector on.
If the TEMPERATURE WARNING INDICATOR continues to flash, follow the procedures below:
(1). Press LAMP POWER ON/OFF button to OFF.

(2). Check the air filter for dust accumulation.
(3). Remove dust with vacuum cleaner (See “AIR FILTER CARE AND CLEANING” section on page 47.)
(4). Press LAMP POWER ON/OFF button to ON.

If the TEMPERATURE WARNING INDICATOR still continues to flash, call Boxlight Corporation at 1-800-762­5757 or 360-779-7901.

Press the LAMP POWER ON/OFF button on the remote control unit or on the projector. The
“Power off ?’’ appears on the screen. Press again the LAMP POWER ON/OFF button to turn
OFF the projector. The LAMP POWER indicator will light bright and READY indicator will
turn off. The cooling fans will operate for 1 minute after the projector is turned off. (During
this “cooling down” period, the projector cannot be turned on.) The READY indicator will light
green again and the projector may be turned on by pressing the LAMP POWER ON/OFF
button. To power down completely, turn the MAIN ON/OFF switch (located on the rear of the
projector) to the OFF position.

DIRECT OPERATION

MODE SELECT

Press the MODE button (located on remote control unit or on the projector) to
select Computer 1, Computer 2 or Video 1 Input. The “Computer 1”, “Computer 2”
or “Video 1” display will appear on the screen for a few seconds.

– 28 –

SOUND VOLUME ADJUSTMENT

Press the VOLUME buttons (located on remote control unit or on the projector) to adjust
the volume. The volume display will be displayed on the screen for a few seconds.
Pressing volume (+) will increase volume and increase the number on the screen.
Pressing volume (–) will decrease volume and decrease the number on the screen.

SOUND MUTE FUNCTION

Pressing the MUTE button on the remote control unit will mute audio. Press the MUTE
button again to restore audio to its previous level. The mute display will be displayed on
the screen for a few seconds.

ZOOM ADJUSTMENT (Top control)

Press the ZOOM ( ) or ( ) button to obtain your desired picture size. For a larger
picture, press ( ) and for a smaller picture, press ( ).

ZOOM ADJUSTMENT (Remote control unit)

Press the ZOOM button and press POINT UP/DOWN button(s) to obtain your desired
picture size. The Zoom display will be displayed on the screen for a few seconds. For a
larger picture, press (UP) and for a smaller picture, press (DOWN).

FOCUS ADJUSTMENT (Top control)

Press the FOCUS ( ) or ( ) button for a sharper, crisper picture.

FOCUS ADJUSTMENT (Remote control unit)

Press the FOCUS button and press POINT UP/DOWN button(s) to obtain a sharper,
crisper picture. The Focus display will be displayed on the screen for a few seconds.

DIGITAL ZOOM FUNCTION

Press the D. ZOOM button on the remote control unit. The message “Quit” is displayed to
indicate Digital Zoom mode. Digital zoom mode can be adjust the image size or pan the
image.
To expand the image size, press SELECT (REAR CLICK) button. The image is magnified
by degrees (Expand function).
To compress the image size, press FRONT CLICK button. The size of image is reduced
by degrees (Compress function).
To pan the image, press POINT UP/DOWN/LEFT/RIGHT (POINTING PAD) button(s).
The image move to the direction indicated (panning function).
To cancel Digital Zoom mode, press other buttons (except NO SHOW button).

NORMAL PICTURE FUNCTION

The normal picture level is factory preset on the projector and can be restored anytime by
pressing the NORMAL button (located on remote control unit or on the projector). The
“Normal” display will be displayed on the screen for a few seconds.

NO SHOW FUNCTION

Press the NO SHOW button on the remote control unit. The screen will change into black
image and the “NO SHOW” is displayed on the screen for a few seconds.

This function is cancelled when the NO SHOW button is pressed again or any other
function button is pressed.

P-TIMER FUNCTION

Press the P-TIMER button on the remote control unit. The timer display “00:00” appears
on the screen and the timer starts to count the time (00:00 to 59:59).
Press again the P-TIMER button to stop the timer. Then press the P-TIMER button to
cancel the P-TIMER function.

FREEZE PICTURE FUNCTION

Press the FREEZE button on the remote control unit, and the picture will remain on-screen. This function is cancelled when
the FREEZE button is pressed again or any other function button is pressed.

NOTE: Your computer or video equipment is not affected by this function, and will continue to run.

AUTO IMAGE FUNCTION

Press the AUTO IMAGE button on the remote control unit or on the projector. The item(s) indicated “ON” in the AUTO IMAGE
FUNCTION are adjusted automatically. If all the items in AUTO IMAGE FUNCTION are “OFF”, AUTO IMAGE SETTING
display appears. If you wish to operate the AUTO IMAGE FUNCTION, perform the steps 3 - 9 of “AUTO IMAGE FUNCTION”
section on page 36.

Quit

MODE

SELECT

AUTO IMAGE NORMAL

MENU

– 29 –

MENU OPERATION

In MENU OPERATION mode, you display menus where you can adjust the projector’s settings. You can use the TOP
CONTROL OF THE PROJECTOR or the REMOTE CONTROL UNIT.

MODE SELECT

You can select a mode using the MENU from among computer 1, computer 2 and video 1.

1. Press the MENU BUTTON and the MAIN MENU DISPLAY dialog box will appear.

2. Press the POINT LEFT/RIGHT BUTTON(s) to select Computer or Video and press the SELECT (REAR CLICK)
BUTTON. Another dialog box MODE DISPLAY will appear.

3. Press the POINT DOWN BUTTON and a red arrow will appear.

4. Move the arrow to the mode you want (computer 1, computer 2 or video 1) to use by pressing the POINT UP/DOWN
BUTTON(s) and then press the SELECT (REAR CLICK) BUTTON.

MAIN MENU DISPLAY

MODE DISPLAY

MAIN MENU DISPLAY

MODE DISPLAY

P-TIMER

M

ENU

A

U

TO

IM

A

G

E

M

U

TE

VOLUME

MODE

FOCUS

ZOOM

F

R

E

E

Z

E

N

O

SH

O

W

D. ZOOM

N

O

R

M

A

L

O

N

-O

F

F

REMOTE CONTROL
UNIT

TOP CONTROL OF
THE PROJECTOR

MENU
BUTTON

POINT
(UP/DOWN/LEFT/RIGHT)
BUTTON
Pressing the button
upward, downward,
leftward or rightward.

POINT UP
BUTTON

POINT LEFT
BUTTON

SELECT
BUTTON

SELECT
(REAR CLICK)
BUTTON

MENU
BUTTON

POINT DOWN
BUTTON

POINT RIGHT
BUTTON

– 30 –

SOUND ADJUSTMENT

You can adjust the sound volume and sound mute used in the MENU.

1. Press the MENU BUTTON and the MAIN MENU DISPLAY dialog box will appear.

2. Press the POINT LEFT/RIGHT BUTTON(s) to select SOUND and press the SELECT (REAR CLICK) BUTTON. Another
dialog box SOUND ADJUST DISPLAY will appear.

3. Press the POINT DOWN BUTTON and a red arrow will appear.

4. Move the arrow to an item that you want to adjust by pressing the POINT UP/DOWN BUTTON(s).

5. To increase the sound volume, point the arrow to ▲ and then press the SELECT (REAR CLICK) BUTTON. To decrease
the sound volume, point the arrow to ▼ and then press the SELECT (REAR CLICK) BUTTON.

6. To mute the sound, point the arrow to Mute and then press the SELECT (REAR CLICK) BUTTON. The mute display is
changed On from Off and mute the sound.

7. To quit the MENU, point to Quit and then press the SELECT (REAR CLICK) BUTTON.

LANGU

AGE ADJUSTMENT

A language used in the MENU is selectable from among English, German, French, Italian, Spanish and Japanese.

1. Press the MENU BUTTON and the MAIN MENU DISPLAY dialog box will appear.

2. Press the POINT LEFT/RIGHT BUTTON(s) to select LANGUAGE and press the SELECT (REAR CLICK) BUTTON.
Another dialog box LANGUAGE SETTING DISPLAY will appear.

3. Press the POINT DOWN BUTTON and a red arrow will appear.

4. Move the arrow to the language you want to use by pressing the POINT UP/DOWN BUTTON(s) and then press the
SELECT (REAR CLICK) BUTTON.

5. The setting is permanently held even if the MAIN ON/OFF is switched off.

MAIN MENU DISPLAY

MAIN MENU DISPLAY

LANGUAGE
SETTING DISPLAY

SOUND ADJUST
DISPLAY

– 31 –

COLOR SYSTEM SELECT (VIDEO MODE)

This projector is compatible with the five major broadcast video standards: PAL, SECAM, NTSC, NTSC 4.43 and PAL-M
(COLOR SYSTEMs). It automatically adjusts itself to optimize its performance for the incoming video (Except PAL-M).
However, if the video signal is not strong enough to detect the video format, the projector may not reproduce the proper
video image. In case this happens, this projector allows you to choose a specific broadcast signal format.

1. Connect the video equipment to the PROJECTOR, and turn them on projector first.

2. Set MODE SELECT to “VIDEO MODE”.

3. Press the MENU BUTTON and the MAIN MENU DISPLAY dialog box will appear.

4. Press the POINT LEFT/RIGHT BUTTON(s) to select SYSTEM and press the SELECT (REAR CLICK) BUTTON. Another
dialog box COLOR SYSTEM DISPLAY will appear. The current COLOR SYSTEM is displayed in the system window.

5. Press the POINT DOWN BUTTON and a red arrow will appear.

6. To change the current COLOR SYSTEM, press the POINT UP/DOWN BUTTON(s) to move the arrow to a desirable
system and then press the SELECT (REAR CLICK) BUTTON.

7. The setting changed remains effective until the MAIN ON/OFF switch is turned off.

MAIN MENU DISPLAY

COLOR SYSTEM
DISPLAY

– 32 –

PICTURE IMAGE ADJUSTMENT (VIDEO MODE)

Although picture adjustments have been preset at the factory, you may want to change the setting.

1. Press the MENU BUTTON and the MAIN MENU DISPLAY dialog box will appear.

2. Press the POINT LEFT/RIGHT BUTTON(s) to select IMAGE and press the SELECT (REAR CLICK) BUTTON. Another
dialog box IMAGE ADJUST DISPLAY will appear. This shows the current picture settings.

3. In this dialog box, you can adjust the settings by increasing or decreasing the levels shown as numbers. The items and
the range of the levels that you can adjust are summarized in the table below.

4. Press the POINT DOWN BUTTON and a red arrow will appear.

5. Move the arrow to an item that you want to adjust by pressing the POINT UP/DOWN BUTTON(s).

6. To increase the level, point the arrow to ▲ and then press the SELECT (REAR CLICK) BUTTON. To decrease the level,
point the arrow to ▼ and then press the SELECT (REAR CLICK) BUTTON.

7. You may want to store the settings in the memory so that you can recall them later. To store the settings, move the arrow
to Stored and then press the SELECT (REAR CLICK) BUTTON. When you have stored the settings, “OK ?” is displayed
for confirmation.

8. Move the arrow to Yes and then press the SELECT (REAR CLICK) BUTTON. The stored settings are permanently held
even if the MAIN ON/OFF is switched off.

9. To quit the MENU, move the arrow to Quit and then press the SELECT (REAR CLICK) BUTTON.

10. If you do not want to store the settings, move the arrow to Quit and then press the SELECT (REAR CLICK) BUTTON.

The settings changed remains effective until the MAIN ON/OFF switch is turned off.

11. To recall the settings from the memory that you have stored, move the arrow to Reset and then press the SELECT

(REAR CLICK) BUTTON. When you have reset the settings, “OK ?” is displayed for confirmation. Move the arrow to
Yes and then press the SELECT (REAR CLICK) BUTTON. You can adjust the settings again if needed.

NOTE: “TINT” will be skipped in the PAL , SECAM and PAL-M mode.

IMAGE
ADJUST DISPLAY

MAIN MENU DISPLAY

TABLE OF PICTURE IMAGE ADJUSTMENT

DECREASES

INCREASES

LIGHTER DEEPER

MORE PURPLE

MORE GREEN

DARKER BRIGHTER
SOFTER SHARPER

COLOR
TINT
CONTRAST

BRIGHTNESS
SHARPNESS

0 63
0 63
0 63
0 63
0 63

– 33 –

PICTURE SCREEN ADJUSTMENT (VIDEO MODE)

This projector has the Wide function, which enables you to view a wider video image.

WIDE function

This projector is able to project not only a normal video image (with 4 x 3 aspect ratio), but also a wider video image by
compressing 4 x 3 image. This feature enable you to enjoy watching pictures like cinema images. You can switch either to
WIDE or to REGULAR screen mode.

1. Press the MENU BUTTON and the MAIN MENU DISPLAY dialog box will appear.

2. Press the POINT LEFT/RIGHT BUTTON(s) to select SCREEN and press the SELECT (REAR CLICK) BUTTON. Another
dialog box SCREEN ADJUST DISPLAY will appear.

3. Press the POINT DOWN BUTTON and a red arrow will appear.

4. To switch to “Wide” mode, move the arrow to Wide by pressing the POINT UP/DOWN BUTTON(s) and then press the
SELECT (REAR CLICK) BUTTON.

5. To switch to “Regular” mode, move the arrow to Regular by pressing the POINT UP/DOWN BUTTON(s) and then press
the SELECT (REAR CLICK) BUTTON.

6. The “Wide” settings remains effective until the MAIN ON/OFF switch is turned off.

MAIN MENU DISPLAY

SCREEN ADJUST
DISPLAY

When the mark ( ) is displayed as
BLACK, computer system mode will be
available on the next page. Move an arrow
to the mark ( ) and press the SELECT
(REAR CLICK) BUTTON to show computer
system mode described on the next page.

– 34 –

COMPUTER SYSTEM SELECT (COMPUTER MODE)

This projector is adjustable to different types of computer display signals based on VGA, SVGA or XGA (See
“COMPATIBLE COMPUTER SPECIFICATIONS” on the next page). If you set MODE SELECT to “COMPUTER”, the
projector will automatically process the incoming signal and project the proper image without any special setting. Although
this will work in most cases, you may be required to manually set the projector for some computer signals. If the computer
image is not reproduced properly, try the following procedure and switch to the computer display mode that you want to
use.

1. Connect the COMPUTER to the PROJECTOR, and turn them on projector first.

2. Set MODE SELECT to “COMPUTER MODE (1 or 2)”. This shows the current display mode initially detected by the
projector in the system window. And “Current mode” display appears.

NOTE: 1. If the projector cannot discriminate or detect the input signal from the computer, the “Go PC adj.” display appears.
NOTE: 2. If no input signal from the computer, the “No signal” display appears on the screen.

3. Press the MENU BUTTON and the MAIN MENU DISPLAY dialog box will appear.

4. Press the POINT LEFT/RIGHT BUTTON(s) to select SYSTEM and press the SELECT (REAR CLICK) BUTTON. Another
dialog box COMPUTER SYSTEM DISPLAY will appear.

5. Press the POINT DOWN BUTTON and a red arrow will appear.

6. If you want to change the current display mode, move the arrow by pressing the POINT UP/DOWN BUTTON(s) to select
one of the modes.

7. Press the SELECT (REAR CLICK) BUTTON to change the display mode.

8. To quit the MENU, move the arrow to Quit and then press the SELECT (REAR CLICK) BUTTON.

PC ADJUSTMENT

This is a special function that may be used when a computer image is not reproduced properly. (See the pages 39 ~ 42 for
more detail.)

COMPUTER
SYSTEM
DISPLAY

CURRENT MODE
DISPLAY

MAIN MENU DISPLAY

– 35 –

Specifications are subject to change without notice.

COMPATIBLE COMPUTER SPECIFICATIONS

ON-SCREEN
DISPLAY

RESOLUTION

640 x 480 31.47 59.88

70.09

70.09

74.38

72.81

56.25

60.32

75.00

85.06

72.19

61.03

55.38

60.51

60.31

51.09

60.51

74.55
60

84.997

75.03

70.07

74.92

60.02

54.58

79.35

31.47

31.47

37.86

37.86

75.00

66.60

66.67

37.50

34.97

35.00

35.156

37.88

46.875

53.674

48.08

37.90

34.50

38.00

38.60

32.70

38.00

49.72

48.36

68.677

60.023

56.476

60.31

48.50

44.00

63.48

720 x 400
640 x 400
640 x 480
640 x 480
640 x 480

640 x 480
640 x 480
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600

832 x 624
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768

Horizontal
Frequency (kHz)

Vertical
Frequency (Hz)

VGA1
VGA2
VGA3
VGA4
VGA5
VGA6

85.0043.269640 x 480VGA7
MAC LC13
MAC 13
SVGA1
SVGA2
SVGA3
SVGA4
SVGA5
SVGA6
SVGA7
SVGA8
SVGA9
SVGA10
SVGA11
MAC 16
XGA1
XGA2
XGA3
XGA4
XGA5
XGA6
XGA7
XGA8

87.17 (Interlace)36.001024 x 768

XGA9

77.0762.041024 x 768

XGA10

75.7061.001024 x 768

XGA11

86.96 (Interlace)35.5221024 x 768

XGA12

58.2046.901024 x 768

XGA13

58.3047.001024 x 768

XGA14

72.0058.031024 x 768

XGA15

75.0860.241024 x 768

MAC19

– 36 –

AUTO IMAGE ADJUSTMENT (COMPUTER MODE)

The Auto image function is provided to automatically adjust Fine sync., Total dots and Screen position for most computers.

1. Press the MENU BUTTON and the MAIN MENU DISPLAY dialog box will appear.

2. Press the POINT LEFT/RIGHT BUTTON(s) to select AUTO IMAGE and press the SELECT (REAR CLICK) BUTTON.
Another dialog box AUTO IMAGE SETTING DISPLAY will appear.

3. Press the POINT DOWN BUTTON and a red arrow will appear.

4. Move the arrow to an item(s) you want to adjust by pressing the POINT UP/DOWN BUTTON(s).

5. Change the setting “On”, press the SELECT (REAR CLICK) BUTTON.

6. Move the arrow by pressing the POINT UP/DOWN BUTTON(s) to select “Go!” and then press the SELECT (REAR CLICK)
BUTTON. The auto image function is started now. It will take about 10 seconds.

7. To store the settings, move the arrow to Stored and then press the SELECT (REAR CLICK) BUTTON. When you have
stored the settings, “OK?” is displayed for confirmation.

8. Move the arrow to Yes and then press the SELECT (REAR CLICK) BUTTON. The stored settings are permanently held
even if the MAIN ON/OFF is switched off.

9. To quit the MENU, point to Quit and then press the SELECT (REAR CLICK) BUTTON.

10. This setting is temporarily effective until you turn off the projector or change the input signal.

NOTE: The fine sync., total dots and screen position of some computers may not be fully adjusted with the “Auto Image

Function”. In that case, use the “Picture Image” and/or “Picture Position” adjustments (see pages 37 ~ 38) to make
fine-adjust them after the “Auto Image Function” is executed.

MAIN MENU DISPLAY

AUTO IMAGE SETTING
DISPLAY

– 37 –

PICTURE IMAGE ADJUSTMENT (COMPUTER MODE)

Picture adjustments have been preset at the factory. If you want to change the setting, operate the projector as follows.

1. Press the MENU BUTTON and the MAIN MENU DISPLAY dialog box will appear.

2. Press the POINT LEFT/RIGHT BUTTON(s) to select IMAGE and press the SELECT (REAR CLICK) BUTTON.
Another dialog box IMAGE ADJUST DISPLAY will appear. This shows the current picture settings.

3. In this dialog box, you can adjust the settings by increasing or decreasing the levels shown as numbers. The items and the
range of the levels that you can adjust are summarized in the table below.

4. Press the POINT DOWN BUTTON and a red arrow will appear.

5. Move the arrow to an item that you want to adjust by pressing the POINT UP/DOWN BUTTON(s).

6. To increase the level, point the arrow to ▲ and then press the SELECT (REAR CLICK) BUTTON. To decrease the level,
point the arrow to ▼ and then press the SELECT (REAR CLICK) BUTTON.

7. You may want to store the settings in the memory so that you can recall them later. To store the settings, move the arrow
to Stored and then press the SELECT (REAR CLICK) BUTTON. When you have stored the settings, “OK ?” is displayed
for confirmation.

8. Move the arrow to Yes and then press the SELECT (REAR CLICK) BUTTON. The stored settings are permanently held
even if the MAIN ON/OFF is switched off.

9. To quit the MENU, move the arrow to Quit and then press the SELECT (REAR CLICK) BUTTON.

10. If you do not want to store the settings, move the arrow to Quit and then press the SELECT (REAR CLICK) BUTTON.

The settings changed remains effective until the MAIN ON/OFF switch is turned off.

11. To recall the settings from the memory that you have stored, move the arrow to Reset and then press the SELECT

(REAR CLICK) BUTTON. When you have reset the settings, “OK ?” is displayed for confirmation. Move the arrow to Yes
and then press the SELECT (REAR CLICK) BUTTON. You can adjust the settings again if needed.

IMAGE ADJUST
DISPLAY

NOTE: The projector may not reproduce a

proper image for some XGA signals.
Since XGA (1024 x 768) image is
converted to 800 x 600 image by
partial scan, some lines and dots of the
image do not appear. Some video
noise of flicker on this compressed
XGA image cannot be eliminated even
though you try to make a Fine sync
adjustment.

MAIN MENU DISPLAY

The number of the total dots in one horizontal period. Adjust the
number to match your PC image.

Adjust the picture as necessary to eliminate flicker
from the display.

TABLE OF PICTURE IMAGE ADJUSTMENT

DECREASE INCREASE
LIGHTER DEEPER
DARKER BRIGHTER

FINE SYNC

TOTAL DOTS
WHITE BALANCE (R/G/B)

CONTRAST
BRIGHTNESS

0 127

0 63
0 63
0 63

– 38 –

PICTURE POSITION ADJUSTMENT (COMPUTER MODE)

1. Press the MENU BUTTON and the MAIN MENU DISPLAY dialog box will appear.

2. Press the POINT LEFT/RIGHT BUTTON(s) to select POSITION and press the SELECT (REAR CLICK) BUTTON.
Another dialog box POSITION SETTING DISPLAY will appear.

3. Press the POINT DOWN BUTTON and a red arrow will appear.

4. Move the arrow to a desirable direction (b, a, c or d) by pressing the POINT LEFT/RIGHT/UP/DOWN BUTTON(s)
and press the SELECT (REAR CLICK) BUTTON to a desirable picture position.

5. You may want to store the settings to the memory so that you can recall them later. To store the settings, move the arrow
to Stored and then press the SELECT (REAR CLICK) BUTTON. When you have stored the settings, “OK ?” is displayed
for confirmation.

6. Move the arrow to Yes and then press the SELECT (REAR CLICK) BUTTON. The stored settings are permanently held
even if the MAIN ON/OFF is switched off.

7. To quit the MENU, move the arrow to Quit and then press the SELECT (REAR CLICK) BUTTON.

8. If you do not want to store the settings, move the arrow to Quit and then press the SELECT (REAR CLICK) BUTTON.
The settings changed remains effective until the MAIN ON/OFF switch is turned off.

9. To recall the settings from the memory that you have stored, move the arrow to Reset and then press the SELECT
(REAR CLICK) BUTTON. When you have reset the settings, “OK ?” is displayed for confirmation. Move the arrow to Yes
and then press the SELECT (REAR CLICK) BUTTON. You can adjust the settings again if needed.

MAIN MENU DISPLAY

POSITION SETTING
DISPLAY

– 39 –

PC ADJUSTMENT

This projector can automatically detect most display signals from most personal computers currently distributed. However,
some computers employ a special signal format which is different from the standard one and may not be detected by this
projector. If this happens, the projector cannot reproduce a proper image. Instead the image is often recognized as a
flickering picture, a non-synchronized picture, a non-centered picture or a skewed picture.

For those non-standard formats, this projector is provided with PC ADJUST, enabling you to precisely adjust several
parameters to match with the input signal format. The projector has eight independent memory areas where you can store
the parameter you have set. This enables you to recall the setting for a specific computer when you need it.

1. Press the MENU BUTTON and the MAIN MENU DISPLAY dialog box will appear.

2. Press the POINT LEFT/RIGHT BUTTON(s) to select PC ADJUST and press the SELECT (REAR CLICK) BUTTON.
Another dialog box “ Where to reserve” will appear.

3. In this dialog box, you will select one of the memory areas from among “Mode 1” to “Mode 8”. If parameters have been
previously set and stored in the memory, the status “Stored” will appear on the corresponding row. If not, “Free” will
appear.

4. Press the POINT DOWN BUTTON and a red arrow will appear.

5. Move the arrow to one of the “Modes” (Free position) where you want to store the parameters by pressing the POINT
UP/DOWN BUTTON(s). Press the SELECT (REAR CLICK) BUTTON to select it.

NOTE: If “Stored” appears in all Modes, no new PC parameter data can be stored. In this case, clear the PC parameter

data using the Mode free Function.

MAIN MENU DISPLAY

– 40 –

6. Another dialog box “PC ADJUSTMENT DISPLAY 1” will appear and the parameter data for the Mode you have selected
is shown in this dialog box.

7. The parameters will be filled with the data determined by the projector according to the present signal input.

8. The function of the parameters and their values are summarized in the table below.

9. Move the arrow to an item that you want to adjust by pressing the POINT UP/DOWN BUTTON(s).

10. To increase the level, point the arrow to ▲ and then press the SELECT (REAR CLICK) BUTTON. To decrease the

level, point the arrow to ▼ and then press the SELECT (REAR CLICK) BUTTON.

11. If you want to store the settings in the memory, move the arrow to Stored and press the SELECT (REAR CLICK)

BUTTON. When you have stored the settings, “OK ?” is displayed for confirmation. Move the arrow to Yes and then
press the SELECT (REAR CLICK) BUTTON .

12. To recall the parameter data before setting, move the arrow to Reset and then press the SELECT (REAR CLICK)

BUTTON. When you have reset the settings, “OK ?” is displayed for confirmation. Move the arrow to Yes and then
press the SELECT (REAR CLICK) BUTTON . You can adjust the settings again if needed.

13. To quit the MENU, move the arrow to Quit and then press the SELECT (REAR CLICK) BUTTON.

14. If you quit the MENU without storing the settings in the memory, the parameter data you changed will not be kept.

15. The stored settings are permanently held even if the MAIN ON/OFF is switched off.

16. Adjust the data such as a “Clamp”, “Display area”, Horiz. scale” and “Vert. scale” if needed, move the arrow by pressing

the POINT UP/DOWN BUTTON(s) to select (▼). Press the SELECT (REAR CLICK) BUTTON.

MAIN MENU DISPLAY

ITEM
TOTAL LINES
TOTAL DOTS
HORIZONTAL
VERTICAL

FUNCTION

The number of the total vertical lines. Adjust the number to match your PC image.
The number of the total dots in one horizontal period. Adjust the number to match your PC image.
Adjustment of the horizontal picture position. When the image is not centered on the screen, adjust this.
Adjustment of the vertical picture position. When the image is not centered on the screen, adjust this.

PC ADJUSTMENT
DISPLAY 1

– 41 –

17. Another dialog box “PC ADJUSTMENT DISPLAY 2” will appear and the parameter data for the Mode you have selected

is shown in this dialog box.

18. Move the arrow to an item that you want to adjust by pressing the POINT UP/DOWN BUTTON(s).

19. To increase the level, point the arrow to ▲ and then press the SELECT (REAR CLICK) BUTTON. To decrease the

level, point the arrow to ▼ and then press the SELECT (REAR CLICK) BUTTON.

20. If you want to store the settings in the memory, move the arrow to Stored and press the SELECT (REAR CLICK)

BUTTON. When you have stored the settings, “OK ?” is displayed for confirmation. Move the arrow to Yes and then
press the SELECT (REAR CLICK) BUTTON .

21. To recall the parameter data before setting, move the arrow to Reset and then press the SELECT (REAR CLICK)

BUTTON. When you have reset the settings, “OK ?” is displayed for confirmation. Move the arrow to Yes and then
press the SELECT (REAR CLICK) BUTTON . You can adjust the settings again if needed.

22. To quit the MENU, move the arrow to Quit and then press the SELECT (REAR CLICK) BUTTON.

23. If you quit the MENU without storing the settings in the memory, the parameter data you changed will not be kept.

24. The stored settings are permanently held even if the MAIN ON/OFF is switched off.

ITEM
CLAMP
DISPLAY AREA
HORIZ. SCALE

FUNCTION

Adjustment of the clamp level. When the image has a dark bar, try this adjustment.
Adjustment the display area to match your PC.
Expanding or compressing level for the horizontal direction.

VERT. SCALE

Expanding or compressing level for the vertical direction.

MAIN MENU DISPLAY

Adjust the display area, move the arrow
by pressing the POINT UP/DOWN
BUTTON(s) to select (s) and press the
SELECT (REAR CLICK) BUTTON.
Another dialog box “DISPLAY AREA
DISPLAY” will appear.
Move the arrow to an item that you want
to select display area by pressing the
POINT UP/DOWN BUTTON(s) and press
the SELECT (REAR CLICK) BUTTON.
Selected mode data will be displayed in
H, V box.
To close dialog, move the arrow to “Quit”
and press the SELECT (REAR CLICK)
BUTTON.

PC ADJUSTMENT
DISPLAY 2

– 42 –

MODE FREE

The Mode free function is provided to confirm or clear the parameter data produced by PC ADJUST.

1. Press the MENU BUTTON and the MAIN MENU DISPLAY dialog box will appear.

2. Press the POINT LEFT/RIGHT BUTTON(s) to select PC ADJUST and press the SELECT (REAR CLICK) BUTTON.

Another dialog box “ Where to reserve” will appear.

3. Press the POINT DOWN BUTTON and a red arrow will appear.

4. Move the arrow to one of the “Modes” (Stored position) that you want to confirm by pressing the POINT UP/DOWN

BUTTON(s). Press the SELECT (REAR CLICK) BUTTON. Another dialog box “PC ADJUSTMENT DISPLAY” will
appear.

5. To quit the MENU, point to Quit and then press the SELECT (REAR CLICK) BUTTON.

6. To modify the parameter data, perform the steps 9 ~ 24 of PC ADJUSTMENT SECTION.

7. To clear the parameter data, move the arrow by pressing the POINT UP/DOWN BUTTON(s) to select Mode free. Press

the SELECT (REAR CLICK) BUTTON. “OK?” is displayed for confirmation.

8. Move the arrow to Yes and then press the SELECT (REAR CLICK) BUTTON to clear the parameter data.

9. To quit the MENU, move the arrow to Quit and then press the SELECT (REAR CLICK) BUTTON.

MAIN MENU DISPLAY

PC ADJUSTMENT
DISPLAY

– 43 –

PICTURE SCREEN ADJUSTMENT (COMPUTER MODE)

This projector can adjust the image size and pan the image with PICTURE SCREEN ADJUSTMENT.

1. Press MENU BUTTON and MAIN MENU DISPLAY dialog box will appear.

2. Press POINT LEFT/RIGHT BUTTON(s) to select SCREEN and press SELECT (REAR CLICK) BUTTON. Another dialog

box SCREEN ADJUST DISPLAY will appear.

3. Press POINT DOWN BUTTON and a red arrow will appear.

4. To adjust the image size or pan the image, move the arrow to Digital zoom by pressing POINT UP/DOWN BUTTON(s)

and then press SELECT (REAR CLICK) BUTTON. MAIN MENU DISPLAY and SCREEN ADJUST DISPLAY will
disappear and the message “Quit” is displayed to indicate Digital Zoom mode.

5. To expand the image size, press SELECT (REAR CLICK) BUTTON. The image is magnified by degrees (Expand

function).

6. To compress the image size, press FRONT CLICK BUTTON. The size of image is reduced by degrees (Compress

function).

7. To pan the image, press POINT UP/DOWN/LEFT/RIGHT (POINTING PAD) BUTTON(s). The image move to the

direction indicated (panning function).

8. To cancel Digital Zoom mode, press other buttons (except NO SHOW button).

9. To turn the image size to true size (800 x 600 in SVGA or XGA, and 640 x 480 in VGA), move the arrow to True by

pressing POINT UP/DOWN BUTTON(s) and then press SELECT (REAR CLICK) BUTTON. The image size is turned to
the true size.

¡This projector cannot display in the resolution more than 1024 x 768. If your computer’s screen resolution is higher than

1024 x 768, reset the resolution to the lower before connecting the projector.

¡The image data of VGA (640 x 480) or XGA (1024 x 768) is modified to fit the screen size in the initial mode.
¡The maximum size in expand mode is 4 times as large as the screen size (800 x 600).
¡The minimum size in compress mode is the screen size (800 x 600) in SVGA, XGA mode, or 640 x 480 in VGA mode.
¡Panning function can work only when the image is expanded.

SCREEN ADJUST
DISPLAY

MAIN MENU DISPLAY

– 44 –

OTHER FUNCTION SETTING

This projector has other function settings; Blue back, Display, Ceiling, Rear, Split wipe and Lamp age.

BLUE BACK

When this function is in the “On” position, the projector will project a blue image without video noise on the screen when the
video source is unplugged or turned off.

DISPLAY

When this function is in the “On” position, on-screen displays always appear when adjustments are made. Although these
on-screen displays are very helpful, these may spoil the view if adjustments are made during presentations. To avoid this,
you can keep back certain displays by switching this function “Off”. The followings are the displays that you can hide.

¡Wait Display
¡Mode Display
¡Volume Display
¡Mute Display
¡Zoom/Focus Display
¡Normal Display
¡No show Display

CEILING

When this function is in the ‘’On’’ position, the top/bottom and the
left/right picture reverse capability lets you project from a ceiling­mounted projector.

REAR

When this function is in the ‘’On’’ position, the left/right picture reverse
capability lets you project onto a rear projection screen.

SPLIT WIPE

Turn SPLIT WIPE function On in the SETTING menu. The picture will change into next one by sliding black image side
ways when the input source is changed.
Change the input source by MODE button. The picture is replaced by black image from side ways to the center, and the
next one appears from the center to side ways like drawing the black curtains.

LAMP A

GE

The Lamp age function is designed to reset the lamp replacement monitor timer. When replacing the lamp, reset the lamp
replacement monitor timer by using this function.

TB

TB

LR

LR

– 45 –

BLUE BACK, DISPLAY, CEILING, REAR AND SPLIT WIPE

1. Press the MENU BUTTON and the MAIN MENU DISPLAY dialog box will appear.

2. Press the POINT LEFT/RIGHT BUTTON(s) to select SETTING and press the SELECT (REAR CLICK) BUTTON.

Another dialog box SETTING DISPLAY will appear.

3. Press the POINT DOWN BUTTON and a red arrow will appear.

4. Move the arrow to an item you want to set by pressing the POINT UP/DOWN BUTTON(s).

5. If you want to change the setting (On or Off), press the SELECT (REAR CLICK) BUTTON.

6. To quit the MENU, point to Quit and then press the SELECT (REAR CLICK) BUTTON.

7. The settings are permanently kept even if the MAIN ON/OFF is switched off.

MAIN MENU DISPLAY

SETTING
DISPLAY

– 46 –

LAMP AGE

NOTE: Do not reset the LAMP REPLACEMENT MONITOR TIMER, except after the lamp is replaced.

1. Press the MENU BUTTON and the MAIN MENU DISPLAY dialog box will appear.

2. Press the POINT LEFT/RIGHT BUTTON(s) to select SETTING and press the SELECT (REAR CLICK) BUTTON.

Another dialog box SETTING DISPLAY will appear.

3. Press the POINT DOWN BUTTON and a red arrow will appear.

4. Move the arrow by pressing the POINT UP/DOWN BUTTON(s) to select Lamp age and then press the SELECT (REAR

CLICK) BUTTON. When you reset the lamp replace monitor, “lamp replace monitor reset?” is displayed for confirmation.

5. Move the arrow to Yes and then press the SELECT (REAR CLICK) BUTTON, “OK?” is displayed for confirmation. Move

the arrow to Yes and then press the SELECT (REAR CLICK) BUTTON, the lamp replace monitor is reset.

6. Move the arrow to No and then press the SELECT (REAR CLICK) BUTTON. The lamp replace monitor is not reset.

7. To quit the MENU, move the arrow to Quit and then press the SELECT (REAR CLICK) BUTTON.

MAIN MENU DISPLAY

SETTING
DISPLAY

– 47 –

The removable air filter prevents dust from accumulating on the surface of the projection lens and projection mirror.
Should the air filter become clogged with dust particles, it will reduce the cooling fan’s effectiveness and may result in internal
heat build up and reduce the life of the projector.

To clean the air filter, follow the cleaning procedures below:

1. Turn the LAMP POWER ON/OFF button OFF.

2. Remove the air filter cover.

3. Remove the air filter from the filter cover.

4. Clean the air filter with a vacuum cleaner.

5. Replace the air filter. Make sure that air filter cover is fully inserted.

Do not clean with water. Doing so may damage the air filter.
Do not operate the projector with air filter removed.

AIR FILTER COVER

AIR FILTER

AIR FILTER
COVER

TEMPERATURE
WARNING
INDICATOR

AIR FILTER CARE AND CLEANING

TEMPERATURE WARNING INDICATOR

RECOMMENDATION

TO ENJOY PICTURE IMAGE, USE THE PROJECTOR IN THE CLEAN
ENVIRONMENT. USAGE IN THE CLEAN ENVIRONMENT IS
RECOMMENDED.

When used under the dusty or smoky conditions, dust may accumulate on
the liquid crystal panel and lens inside it, and may resultantly be projected
on the screen together with the picture.
When the above symptoms are noticed, contact a Boxlight Corporation at
1-800-762-5757 or 360-779-7901 for cleaning.

The TEMPERATURE WARNING INDICATOR flashes red when the internal
temperature of the projector exceeds the normal temperature.
Possible causes for the temperature warning may be:

1. Ventilation slots of the projector are blocked. In such an event, reposition
the projector so that ventilation slots are not obstructed.

2. Air filter is clogged with dust particles. Remove dust from the air filter by
following instructions in the Air Filter Care and Cleaning section above.

3. If temperature warning indicator remains on after performing the checks
listed above, cooling fan/internal circuits may be malfunctioning. Request
service from an authorized dealer or service station.

– 48 –

If the lamp fails to come on and the lamp monitor on the projector light is orange, you must replace the bulb.

¡For continued safety, replace with a lamp assembly of the same type.
¡Allow the projector to cool for at least 45 minutes before you open the lamp cover. The inside of the

projector can become very hot.

¡Do not drop the lamp module or touch the glass bulb ! The glass can shatter and cause injury.

Follow these steps to replace the lamp assembly.

1. Turn off the projector and allow the projector to cool thoroughly.

2. Disconnect the AC cord from the projector.

3. Remove screw with a screwdriver and disconnect the lamp cover.

4. Remove 2 screws with a screwdriver and pull out the lamp assembly by
grasping the handle.

5. Replace the lamp assembly.

6. Tighten 3 screws to secure the lamp cover to the lamp assembly.

7. Connect the detachable AC cord to the projector.

LAMP REPLACEMENT

8. Reset the lamp replacement monitor timer. (See “LAMP AGE” section on page 46.)

NOTE: Do not reset the LAMP REPLACEMENT MONITOR TIMER, except after the lamp is replaced.

LAMP REPLACEMENT
INDICATOR

LAMP
ASSEMBLY

HANDLE

LAMP COVER

ORDER REPLACEMENT LAMP

Replacement Lamp can be ordered through Boxlight Corporation at 1-800-762-5757 or 360-779-7901. When ordering the
Lamp, give the following information to the dealer.

● Model No. of your projector : Boxlight MP-25t

● Replacement Lamp Type No. : POA-LMP18J

(Service Parts No. 610 279 5417)

– 49 –

CLEANING THE LENS

Follow these steps to clean the projection lens:

1. Apply a non-abrasive camera lens cleaner to a soft, dry cleaning cloth.
Avoid using an excessive amount of cleaner.
Abrasive cleaners, solvents or other harsh chemicals might scratch the lens.

2. Lightly wipe the cleaning cloth over the lens.

3. If you don’t intend to use the projector immediately, replace the lens cover.

TROUBLESHOOTING

Before calling Boxlight Corporation for assistance, check the matters below once again.

1. Make sure you have connected the projector to your equipment as described in section “ CONNECTING THE
PROJECTOR” on pages 10 ~ 17.

2. Check cable connections. Verify that all computer, video and power cords are properly connected.

3. Verify that power is switched on.

4. If the projector still does not display an image, restart the computer.

5. If the image still does not display, unplug the projector from the computer and check the computer monitor’s display.
The problem may be with your graphics controller rather than with the projector. (When you reconnect the projector,
remember to turn the computer and monitor off before you power up the projector. Power the equipment back up in this
order: Projector, monitor, computer)

6. If the problem still exists, check the following chart.

¡Plug the projector into an AC outlet.
¡Turn the MAIN ON/OFF button to ON.
¡Press the LAMP POWER ON/OFF switch to ON.
¡Be sure the READY INDICATOR light is ON.
¡Wait one minute after the projector is turned OFF before turning the projector

back on.

NOTE: After pressing the LAMP POWER ON/OFF button to OFF . The projector

functions as indicated.

1. The LAMP POWER indicator will light and the READY indicator will turn off.

2. After one minute, the READY indicator will light green again and the projector
may be turned on by pressing the LAMP POWER ON/OFF button.

¡Check temperature warning indicator. If the indicator flashes red, the projector

cannot be turned on. (See “USING THE PROJECTOR” section on page 27).

¡Check the projection lamp.
¡Adjust the focus.

¡Make sure the projection screen is at least 3.6 feet (1.1 m) from the projector.
¡Check the projection lens to see if it needs cleaning.

NOTE: Moving the projector from a cool temperature location to a warm

temperature location may result in moisture condensation on the lens. In
such an event, leave the projector OFF and wait until condensation
disappears.

Problem:

No power

Image is out of focus

Try these Solutions:

– 50 –

Problem:

Check Ceiling feature.
(See “OTHER FUNCTION SETTING” section on pages 44 ~ 45).

Picture is T/B inverted.

Check Ceiling/Rear feature.
(See “OTHER FUNCTION SETTING” section on pages 44 ~ 45).

Picture is L/R Reversed.

Check Display feature.
(See “OTHER FUNCTION SETTING” section on pages 44 ~ 45).

Some displays are not seen
during the operation.

¡Check audio cable connection from audio input source.
¡Adjust audio source.
¡Press the VOLUME (+) button.
¡Press the MUTE button.

No sound.

¡Check the batteries.
¡Make sure nothing is blocking between the remote control sensor and remote

control unit.

¡Make sure you are not too far from the projector when using the remote control

unit. {Maximum operate range 16.4 feet (5 m)}.

Remote control unit doesn’t
work.

¡Check the cable connection between the projector and the computer.
¡Check the mouse setting on your computer.
¡Turn on the projector before you turn on the computer.

Wireless mouse function does
not work.

Try these Solutions:

SERVICE

WARNING: High voltages are used to operate this projector. Do not attempt to open the cabinet.

Boxlight Service is easily obtained. If after following instructions above, you find that service is necessary, contact Boxlight for
assistance at 1-800-762-5757 or 360-779-7901.

Give the model number and explain the difficulty. We will advise you how to obtain service.
Please have the following information available:

● Serial Number of Projector.

● Resolution of Computer.

● Refresh rate of Computer.

OPTIONAL PARTS

The parts listed below are optionally supplied. When ordering those parts, give the name and the Type No. of it to the sales
dealer.

● Control Cable for Serial Port Type No. : POA-MC12SRL (Service Parts No. 645 025 6349)

● Control Cable for ADB Port Type No. : POA-MC12MAC (Service Parts No. 645 024 6326)

● MAC Adapter Type No. : POA-MACAP (Service Parts No. 645 031 8207)

– 51 –

TECHNICAL SPECIFICATIONS

SPECIFICATIONS

Projector Type
Dimensions (W x H x D)
Net Weight
LCD Panel System
Number of Pixels
Color System
Scanning Frequency
Projection Image Size (Diagonal)
Contrast Ratio
Horizontal Resolution
Projection Lens
Throw Distance
Projection Lamp
Projection Mirror
AV Input jacks
Computer Input Jack
Monitor Output Jack
Computer Audio Input Jack

Other Jacks
Built-in Speaker
Image Elevation Adjustment
Voltage
Power Consumption
Operating Temperature
Storage Temperature
Remote Control Battery

Multi-media Projector

10.7” (272 mm) x 5.7” (145.5 mm) x 16.2” (412.5 mm)

14.6 Ibs (6.6 kg)

1.3” TFT Active Matrix type (Thin Film Transistor) x 3
1,440,000 {480,000 (800 x 600) x 3}
5 color system (PAL, SECAM, NTSC, NTSC4.43 and PAL-M)
H-sync. 15 ~ 100 KHz, V-sync. 50 ~ 100 Hz
Adjustable from 30” to 300” (76.2 cm to 762 cm)
300 : 1
750 TV lines
F1.8 ~ 2.1 lens with f48.4 mm ~ 62.8 mm Motor zoom and focus

4.6’ (1.4 m) ~ 35.4’ (10.8 m)
150 watt type
Dichroic mirror and X-prism system
RCA Type x 1 (Video, Audio R and L) and DIN 4 pin (S-Video) x 1
(VGA) HDB15 Terminal x 2, Multi-pole 12 pin (Control port) x 2
(VGA) HDB15 Terminal x 1
Mini Stereo Type x 2

Video Monitor Output Jack RCA Type x 1
Audio Monitor Output Jacks RCA Type x 1 (R and L)

EXT. Speaker Jack x 1
INT. SP. Stereo (R and L), 2 watt RMS (T.H.D. 10%)
Up to 6°
100 ~ 120V, 200 ~ 240V AC, 50/60 Hz

2.9/1.5A (Max. Ampere)
5°C ~ 35°C, 41°F ~ 95°F
–10°C ~ 60°C, 14°F ~ 140°F
(2) AA Type

This symbol on the nameplate means the product is Listed by Underwriters
Laboratories Inc. It is designed and manufactured to meet rigid U.L. safety
standards against risk of fire, casualty and electrical hazards.

LIMITED WARRANTY

BOXLIGHT CORPORATION (“BOXLIGHT”) warrants that each Boxlight MP-25t (“the Product”) sold hereunder will
conform to and function in accordance with the written specifications of BOXLIGHT. Said limited warranty shall apply
only to the first person or entity that purchases the Product for personal or business use and not for the purpose of
distribution resale. Said warranty shall continue for a period of two (2) years from the date of such purchase.
BOXLIGHT does not warrant that the Product will meet the specific requirements of the first person or entity that
purchases the Product for personal or business use. Lamp is warrantied for 120 days.

BOXLIGHT CORPORATION’s liability for the breach of the foregoing limited warranty is limited to the repair or
replacement of the Product or refund of the purchase price of the Product, at BOXLIGHT’s sole option. To exercise
the Purchaser’s rights under the foregoing warranty, the Product must be returned at the Purchaser’s sole cost and
expense, to BOXLIGHT or any authorized service center provided, however, that the Product must be accompanied by
a written letter explaining the problem and which includes (i) proof of purchase; (ii) the dealer’s name; (iii) the model
and serial number of the Product. A return authorization number, issued by the BOXLIGHT customer service
department, must also be clearly displayed on the outside of the shipping carton containing the Product.

WARRANTY LIMITATION AND EXCLUSION

BOXLIGHT CORPORATION shall have not further obligation under the foregoing limited warranty if the Product has
been damaged due to abuse, misuse, neglect, accident, unusual physical or electrical stress, unauthorized
modification, tampering, alterations, or service other than by BOXLIGHT or its authorized agents, causes other than
from ordinary use or failure to properly use the Product in the application for which said Product is intended.

DISCLAIMER OR UNSTATED WARRANTIES

The warranty printed above is the only warranty applicable to this purchase.
All other warranties express or implied, including, but not limited to, the implied warranties or merchantability and
fitness for a particular purpose are disclaimed. There are no warranties that extend beyond the face of hereof and the
foregoing warranty shall not be extended, altered or varied except by written instrument signed by BOXLIGHT
CORPORATION.

LIMITATION OR LIABILITY

It is understood and agreed that BOXLIGHT’s liability whether in contract, in tort, under any warranty, in negligence or
otherwise shall not exceed the return of the amount of the purchase price paid by purchaser and under no
circumstances shall BOXLIGHT be liable for special, indirect or consequential damages. The price stated for the
Product is a consideration in limiting BOXLIGHT’s liability. No action regardless of form, arising out of the agreement
to purchase the product, may be brought by purchaser more than one year after the cause of action has accrued.

Printed in Japan
Part No. 610 284 0094 (1AA6P1P2233-- M6YEB)

Boxlight
19332 Powder Hill Place
Poulsbo, WA 98370-7407 USA
www

.boxlight.com
U.S. and Canada 800-762-5757
International 360-779-7901