Bostitch BTFP02012 Operation And Maintenance Manual

OPERATION and MAINTENANCE MANUAL

MANUALES DE OPERACIÓN y MANTENIMIENTO

LES MANUELS D’UTILISATION et D’ENTRETIEN

INSTRUCTIVO DE OPERACIÓN, CENTROS
DE SERVICIO Y PÓLIZA DE GARANTÍA.

LÉASE ESTE INSTRUCTIVO

ANTES DE USAR EL PRODUCTO.

SAFETY GUIDELINES - DEFINITIONS

This manual contains information that is important for you to know and understand.
This information relates to protecting YOUR SAFETY and PREVENTING EQUIPMENT
PROBLEMS. To help you recognize this information, we use the symbols below. Please
read the manual and pay attention to these symbols.

Indicates an imminently

hazardous situation which, if not avoided,
will result in death or serious injury.

Indicates a potentially

hazardous situation which, if not avoided,
may result in minor or moderate injury.

Indicates a potentially

hazardous situation which, if not avoided,
could result in death or serious injury.

Indicates a practice not
related to personal injury which, if not
avoided, may result in property damage.

IMPORTANT SAFETY INSTRUCTIONS

This product contains chemicals known to the State of California to

cause cancer, and birth defects or other reproductive harm. Wash hands after handling.

Some dust contains chemicals known to the State of California to cause
cancer, birth defects or other reproductive harm such as asbestos and lead in lead based
paint.

Not for use with foodstuffs or ingestible products. This product
contains chemicals known to the State of California to cause cancer, and birth defects or
other. reproductive harm. Wash hands after handling.

To reduce the risk of injury, read the instruction manual.

SAVE THESE INSTRUCTIONS

HAZARD

RISK OF EXPLOSION OR FIRE

WHAT CAN HAPPEN HOW TO PREVENT IT

• It is normal for electrical contacts within

the motor and pressure switch to spark.

• Always operate the compressor in a
well ventilated area free of combustible
materials, gasoline, or solvent vapors.

• If electrical sparks from compressor come
into contact with flammable vapors, they
may ignite, causing fire or explosion.

• If spraying flammable materials, locate
compressor at least 20' (6.1 m) away
from spray area. An additional length of
air hose may be required.

• Store flammable materials in a secure
location away from compressor.

• Restricting any of the compressor
ventilation openings will cause serious
overheating and could cause fire.

• Never place objects against or on top of
compressor.

• Operate compressor in an open area at
least 12" (30.5 cm) away from any wall or
obstruction that would restrict the flow of
fresh air to the ventilation openings.

• Operate compressor in a clean, dry well
ventilated area. Do not operate unit in
any confined area. Store indoors.

• Unattended operation of this product
could result in personal injury or property
damage. To reduce the risk of fire, do
not allow the compressor to operate
unattended.

• Always remain in attendance with the
product when it is operating.

• Always turn off and unplug unit when not
in use.

HAZARD

RISK TO BREATHING (ASPHYXIATION)

WHAT CAN HAPPEN HOW TO PREVENT IT

• The compressed air directly from your
compressor is not safe for breathing. The
air stream may contain carbon monoxide,
toxic vapors, or solid particles from the air
tank. Breathing these contaminants can
cause serious injury or death.

• Never use air obtained directly from the
compressor to supply air for human
consumption. The compressor is not
equipped with suitable filters and
in-line safety equipment for human
consumption.

• Exposure to chemicals in dust created by
power sanding, sawing, grinding, drilling,
and other construction activities may be
harmful.

• Sprayed materials such as paint, paint
solvents, paint remover, insecticides,
weed killers, may contain harmful vapors
and poisons.

• Work in an area with good cross
ventilation. Read and follow the safety
instructions provided on the label or
safety data sheets for the materials you
are spraying. Always use certified safety
equipment: NIOSH/OSHA respiratory
protection or properly fit ting face mask
designed for use with your specific
application.

HAZARD

RISK OF BURSTING

Air Tank: On February 26, 2002, the U.S. Consumer Product Safety Commission

published Release # 02-108 concerning air compressor tank safety:
Air compressor receiver tanks do not have an infinite life. Tank life is dependent upon
several factors, some of which include operating conditions, ambient conditions, proper
installations, field modifications, and the level of maintenance. The exact effect of these
factors on air receiver life is difficult to predict.
If proper maintenance procedures are not followed, internal corrosion to the inner wall of
the air receiver tank can cause the air tank to unexpectedly rupture allowing pressurized
air to suddenly and forcefully escape, posing risk of injury to consumers.
Your compressor air tank must be removed from service by the end of the year shown on
your tank warning label.
The following conditions could lead to a weakening of the air tank, and result in a violent
air tank explosion:

WHAT CAN HAPPEN HOW TO PREVENT IT

• Failure to properly drain condensed water
from air tank, causing rust and thinning of
the steel air tank.

• Drain air tank daily or after each use.
If air tank develops a leak, replace it
immediately with a new air tank or
replace the entire compressor.

• Modifications or attempted repairs to the
air tank.

• Never drill into, weld, or make any
modifications to the air tank or its
attachments. Never attempt to repair a
damaged or leaking air tank. Replace
with a new air tank.

• Unauthorized modifications to the safety
valve or any other components which
control air tank pressure.

• The air tank is designed to withstand
specific operating pressures. Never make
adjustments or parts substitutions to
alter the factory set operating pressures.

Attachments & accessories:

• Exceeding the pressure rating of air tools,
spray guns, air operated accessories,
tires, and other inflatables can cause
them to explode or fly apart, and could
result in serious injury.

• Follow the equipment manufacturers
recommendation and never exceed the
maximum allowable pressure rating of
attachments. Never use compressor to
inflate small low pressure objects such
as children’s toys, footballs, basketballs,
etc.

Tires:

• Over inflation of tires could result in
serious injury and property damage.

• Use a tire pressure gauge to check the
tires pressure before each use and while
inflating tires; see the tire sidewall for the
correct tire pressure.

NOTE: Air tanks, compressors and similar

equipment used to inflate tires can fill
small tires very rapidly. Adjust pressure
regulator on air supply to no more than
the rating of the tire pressure. Add air in
small increments and frequently use the
tire gauge to prevent over inflation.

HAZARD

RISK OF ELECTRICAL SHOCK

WHAT CAN HAPPEN HOW TO PREVENT IT

• Your compressor is powered by electricity.
Like any other electrically powered
device, if it is not used properly it may
cause electric shock.

• Never operate the compressor outdoors
when it is raining or in wet conditions.

• Never operate compressor with
protective covers removed or damaged.

• Repairs attempted by unqualified
personnel can result in serious injury or
death by electrocution.

• Any electrical wiring or repairs required
on this product should be performed
by authorized service center personnel
in accordance with national and local
electrical codes.

• Electrical Grounding: Failure to provide

adequate grounding to this product
could result in serious injury or death
from electrocution. Refer to Grounding
Instructions paragraph in the Installation
section.

• Make certain that the electrical circuit
to which the compressor is connected
provides proper electrical grounding,
correct voltage and adequate fuse
protection.

HAZARD

RISK FROM FLYING OBJECTS

WHAT CAN HAPPEN HOW TO PREVENT IT

• The compressed air stream can cause
soft tissue damage to exposed skin and
can propel dirt, chips, loose particles, and
small objects at high speed, resulting in
property damage or personal injury.

• Always wear certified safety equipment:
ANSI Z87.1 eye protection (CAN/CSA
Z94.3) with side shields when using the
compressor.

• Never point any nozzle or sprayer toward
any part of the body or at other people or
animals.

• Always turn the compressor off and
bleed pressure from the air hose and
air tank before attempting maintenance,
attaching tools or accessories.

HAZARD

RISK OF HOT SURFACES

WHAT CAN HAPPEN HOW TO PREVENT IT

• Touching exposed metal such as the
compressor head, engine head, engine
exhaust or outlet tubes (J, Fig. 2), can
result in serious burns.

• Never touch any exposed metal parts on
compressor during or immediately after
operation. Compressor will remain hot
for several minutes after operation.

• Do not reach around protective shrouds
or attempt maintenance until unit has
been allowed to cool.

HAZARD

RISK FROM MOVING PARTS

WHAT CAN HAPPEN HOW TO PREVENT IT

• Moving parts such as the pulley, flywheel,
and belt can cause serious injury if they
come into contact with you or your
clothing.

• Never operate the compressor with
guards or covers which are damaged or
removed.

• Keep your hair, clothing, and gloves
away from moving parts. Loose clothes,
jewelry, or long hair can be caught in
moving parts.

• Air vents may cover moving parts and
should be avoided as well.

• Attempting to operate compressor with
damaged or missing parts or attempting
to repair compressor with protective
shrouds removed can expose you to
moving parts and can result in serious
injury.

• Any repairs required on this product
should be performed by authorized
service center personnel.

HAZARD

RISK OF UNSAFE OPERATION

WHAT CAN HAPPEN HOW TO PREVENT IT

• Unsafe op er a tion of your compressor
could lead to se ri ous in jury or death to
you or others.

• Review and understand all instructions
and warnings in this manual.

• Be come fa mil iar with the op eration and
con trols of the air compressor.

• Keep operating area clear of all persons,
pets, and obstacles.

• Keep chil dren away from the air
compressor at all times.

• Do not operate the product when
fatigued or under the influence of alcohol
or drugs. Stay alert at all times.

• Never defeat the safety features of this
prod uct.

• Equip area of operation with a fire
extinguisher.

• Do not op er ate machine with missing,
broken, or un au tho rized parts.

• Never stand on the compressor.

HAZARD

RISK OF FALLING

WHAT CAN HAPPEN HOW TO PREVENT IT

• A portable compressor can fall from a
table, workbench, or roof causing damage
to the compressor and could result in
serious injury or death to the operator.

• Always operate compressor in a stable
secure position to prevent accidental
movement of the unit. Never operate
compressor on a roof or other elevated
position. Use additional air hose to reach
high locations.

HAZARD

RISK FROM NOISE

WHAT CAN HAPPEN HOW TO PREVENT IT

• Under some conditions and duration
of use, noise from this product may
contribute to hearing loss.

• Always wear proper hearing protection
during use.

SAVE THESE INSTRUCTIONS

FOR FUTURE USE

SPECIFICATIONS

Model No. BTFP02012

Bore 1.875" (47.6 mm)
Stroke 1.250" (31.8 mm)
Voltage/Hz-Single Phase 120/60
Minimum Branch Circuit Requirement 15 amps
Fuse Type Time Delay
Air Tank Capacity 6 Gallon (22.7 liters)
Approximate Cut-in Pressure 120 psig
Approximate Cut-out Pressure 150 psig
SCFM @ 40 psig 3.7 *
SCFM @ 90 psig 2.6 *
Regulated Pressure Rating (Approximate) 3–150 psi
Quick Connect Type 1/4" (6.4 mm) Industrial

*Tested per ISO 1217
Refer to Glossary for abbreviations.

GLOSSARY

Become familiar with these terms before operating the unit.

CFM: Cubic feet per minute.
SCFM: Standard cubic feet per minute; a unit of measure of air delivery.
PSIG: Pounds per square inch gauge; a unit of measure of pressure.
Code Certification: Products that bear one or more of the following marks: UL

®

, CUL,

CULUS, ETL

®

, CETL, CETLUS, have been evaluated by OSHA certified independent safety

laboratories and meet the applicable Standards for Safety.
Cut-In Pressure: While the motor is off, air tank pressure drops as you continue to use
your accessory. When the tank pressure drops to a certain lower level the motor will restart
automatically. The low pressure at which the motor automatically restarts is called "cut-in"
pressure.
Cut-Out Pressure: When an air compressor is turned on and begins to run, air pressure in
the air tank begins to build. It builds to a certain high pressure before the motor automati­cally shuts off, protecting your air tank from pressure higher than its capacity. The high pres­sure at which the motor shuts off is called "cut-out" pressure.
Branch Circuit: Circuit carrying electricity from electrical panel to outlet.

BTFP02012

OIL FREE PORTABLE AIR COMPRESSOR

COMPRESSEUR D’AIR PORTATIF SANS HUILE

COMPRESOR DE AIRE SIN ACEITE PORTÁTIL

Part No. N410108 March 15

DUTY CYCLE

This air compressor pump is capable of running continuously. However, to prolong the life of
your air compressor, it is recommended that a 50%-75% average duty cycle be maintained;
that is, the air compressor pump should not run more than 30-45 minutes in any given hour.

ASSEMBLY

UNPACKING

Remove unit from carton and discard all packaging.

INSTALLATION

HOW TO SET UP YOUR UNIT

Location of the Air Compressor

• Locate the air compressor in a clean, dry and well ventilated area.

• The air compressor should be located at least 12" (30.5 cm) away from the wall or other
obstructions that will interfere with the flow of air.

• The air compressor pump and shroud are designed to allow for proper cooling. The
ventilation openings on the compressor are necessary to maintain proper operating
temperature. Do not place rags or other containers on or near these openings.

GROUNDING INSTRUCTIONS (FIG. 1)

RISK OF ELECTRICAL SHOCK. In the event of a short circuit,
grounding reduces the risk of shock by providing an escape wire for the electric
current. This air compressor must be properly grounded.

The portable air compressor is equipped with a cord having a grounding wire with an appro­priate grounding plug (A).

1. The cord set and plug (A) with this unit contains a grounding pin (B). This plug MUST be

used with a grounded outlet (C).

IMPORTANT: The outlet being used must be installed and grounded in accordance with all
local codes and ordinances.

2. Make sure the outlet being used has the same configuration as the grounded plug. DO

NOT USE AN ADAPTER. See figure 1.

3. Inspect the plug and cord before each use. Do not use if there are signs of damage.

4. If these grounding instructions are not completely understood, or if in doubt as to

whether the compressor is properly grounded, have the installation checked by a
qualified electrician.

RISK OF ELECTRICAL SHOCK. IMPROPER GROUNDING CAN RESULT
IN ELECTRICAL SHOCK.

Do not modify the plug provided. If it does not fit the available outlet, a correct outlet
should be installed by a qualified electrician.
Repairs to the cord set or plug MUST be made by a qualified electrician.

EXTENSION CORDS

If an extension cord must be used, be sure it is:

• a 3-wire extension cord that has a 3-blade grounding plug, and a 3-slot receptacle that

will accept the plug on the product

• in good condition

• no longer than 50' (15.2 m)

• 14 gauge (AWG) or larger. (Wire size increases as gauge number decreases. 12 AWG

and 10 AWG may also be used. DO NOT USE 16 OR 18 AWG.)

Risk of Property Damage. The use of an undersized extension cord will
cause voltage to drop resulting in power loss to the motor and overheating. Instead of using
an extension cord, increase the working reach of the air hose by attaching another length of
hose to its end. Attach additional lengths of hose as needed.

VOLTAGE AND CIRCUIT PROTECTION

Refer to the Specification Chart for the voltage and minimum branch circuit requirements.

Risk of Overheating. Certain air compressors can be operated on a 15 amp

circuit if the following conditions are met.

1. Voltage supply to circuit must comply with the National Electrical Code.

2. Circuit is not used to supply any other electrical needs.

3. Extension cords comply with specifications.

4. Circuit is equipped with a 15 amp circuit breaker or 15 amp time delay fuse.
NOTE: If compressor is connected to a circuit protected by fuses, use only time delay

fuses. Time delay fuses should be marked "D" in Canada and "T" in the US.
If any of the above conditions cannot be met, or if operation of the compressor repeatedly
causes interruption of the power, it may be necessary to operate it from a 20 amp circuit. It
is not necessary to change the cord set.

OPERATION

KNOW YOUR AIR COMPRESSOR

READ THIS OWNER’S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR UNIT.
Compare the illustrations with your unit to familiarize yourself with the location of various
controls and adjustments. Save this manual for future reference.

DESCRIPTION OF OPERATION (FIG. 2–4)

Become familiar with these controls before operating the unit.
On(I)/Off(O) Switch (D): Place this switch in the On (I) position to provide automatic power
to the pressure switch and Off (O) to remove power at the end of each use.
Pressure Switch (not shown): The pressure switch automatically starts the motor when
the air tank pressure drops below the factory set "cut-in" pressure. It stops the motor
when the air tank pressure reaches the factory set "cut-out" pressure.
Safety Valve (H): If the pressure switch does not shut off the air compressor at its "cut­out" pressure setting, the safety valve will protect against high pressure by "popping out"
at its factory set pressure (slightly higher than the pressure switch "cut-out" setting).
Tank Pressure Gauge (I): The tank pressure gauge indicates the reserve air pressure in
the tank.
Outlet Pressure Gauge (E): The outlet pressure gauge indicates the air pressure available
at the outlet side of the regulator. This pressure is controlled by the regulator and is always
less than or equal to the tank pressure.
Regulator (G): Controls the air pressure shown on the outlet pressure gauge. Turn regu­lator knob clockwise to increase pressure and counterclockwise to decrease pressure.
Cooling System (not shown): This compressor contains an advanced design cooling
system. At the heart of this cooling system is an engineered fan. It is perfectly normal for
this fan to blow air through the vent holes in large amounts. You know that the cooling
system is working when air is being expelled.
Air Compressor Pump (not shown): Compresses air into the air tank. Working air is not
available until the compressor has raised the air tank pressure above that required at the
air outlet.
Drain Valve (K): The drain valve is located at the base of the air tank and is used to drain
condensation at the end of each use.
Check Valve (M): When the air compressor is operating, the check valve is "open", allowing
compressed air to enter the air tank. When the air compressor reaches "cut-out" pressure,
the check valve "closes", allowing air pressure to remain inside the air tank.
Motor Overload Protector (not shown): The motor has a thermal overload protector. If the
motor overheats for any reason, the overload protector will shut off the motor. The motor
must be allowed to cool down before restarting. To restart:

1. Set the On/Off lever to "Off" and unplug unit.

2. Allow the motor to cool.

3. Plug the power cord into the correct branch circuit receptacle.

4. Set the Auto/Off lever to "On" position.
Quick-Connect Body (F): The quick connect body accepts industrial quick connect plugs.
The two quick connect bodies allow the use of two tools at the same time.

HOW TO USE YOUR UNIT (FIG. 2)

How to Stop

1. Set the On/Off switch (D) to "Off".

2. Unplug unit when not in use.

Before Starting

Do not operate this unit until you read this instruction manual for

safety, operation and maintenance instructions.
Before Each Start-Up

1. Set the On/Off switch (D) to "Off".

2.

Plug the power cord into the correct branch circuit receptacle.

(Refer to Voltage and

Circuit Protection paragraph in the Installation section of this manual.)

3. Turn the regulator knob (G) counterclockwise to set the outlet pressure to zero.

4. Turn regulator knob (G) counterclockwise until fully closed. Ensure regulated pressure

gauge reads 0 PSI (0 kPa).

5. Attach hose and accessories.

6. Ensure all covers and labels are in place, legible (for labels) and securely mounted. Do

not use compressor until all items have been verified.

Risk of unsafe operation. Firmly grasp air hose in hand when installing

or disconnecting to prevent hose whip.

Risk of unsafe operation. Do not use damaged or worn accessories.

NOTE: The hose or accessory will require a quick connect plug if the air outlet is equipped

with a quick connect body (F).

Risk of Bursting. Too much air pressure causes a hazardous risk of
bursting. Check the manufacturer’s maximum pressure rating for air tools and acces­sories. The regulator outlet pressure must never exceed the maximum pressure rating.

Risk of property damage. Compressed air from the unit may contain wa ter
condensation and oil mist. Do not spray un fil tered air at an item that could be damaged by
moisture. Some air tools and accessories may require filtered air. Read the in struc tions for
the air tools and accessories.

How to Start

1. Set the On/Off switch (D) to "On" and allow tank pressure to build. Motor will stop when

tank pressure reaches "cut-out" pressure.

2. Turn regulator knob (G) clockwise to increase pressure and stop when desired pressure

is reached.

Risk of unsafe operation. If any unusual noise or vibration is noticed,

stop the compressor immediately and have it checked by a trained service technician.

The compressor is ready for use.

MAINTENANCE

CUSTOMER RESPONSIBILITIES

Before each use Daily or after

each use

See tank warning label

Check Safety Valve X
Drain Tank X
Remove tank from service X

1

1- For more information,

call our Customer Care Center at 1-800-556-6696

Risk of unsafe operation. Unit cycles automatically when power is on.

When performing maintenance, you may be exposed to voltage sources, compressed
air, or moving parts. Personal injuries can occur. Before performing any maintenance
or repair, disconnect power source from the compressor and bleed off all air pressure.

C

A

B

Risk from Flying Objects. Always wear certified safety equipment:

ANSI Z87.1 eye protection (CAN/CSA Z94.3) with side shields.

Before starting compressor, pull the ring on the safety valve (H) to make sure that the safety
valve operates freely. If the valve is stuck or does not operate smoothly, it must be replaced
with the same type of valve.

TO DRAIN TANK (FIG. 2, 3)

Risk of Unsafe Operation. Air tanks contain high pressure air. Keep
face and other body parts away from outlet of drain. Use ANSI Z87.1 eye protection
(CAN/CSA Z94.3) when draining as debris can be kicked up into face.

Risk from noise. Always wear proper hearing protection during use.
Under some conditions and duration of use, noise from this product may contribute
to hearing loss.

NOTE: All compressed air systems generate condensate that accumulates in any drain

point (e.g., tanks, filter, aftercoolers, dryers). This condensate contains lubricating oil and/or
substances which may be regulated and must be disposed of in accordance with local, state,
and federal laws and regulations.

Risk of Bursting. Water will condense in the air tank. If not drained,
water will corrode and weaken the air tank causing a risk of air tank rupture.

Risk of Property Damage. Drain water from air tank may contain oil and rust
which can cause stains.

1. Set the On/Off switch (D) to "Off".

2. Turn the regulator knob (G) counterclockwise to set the outlet pressure to zero.

3. Remove the air tool or accessory.

4. Place a suitable container under the drain valve to catch discharge.

5. Pull ring on safety valve (H) allowing air to bleed from the tank until tank pressure is

approximately 20 psi. Release safety valve ring.

6. Drain water from air tank by opening drain valve (K) on bottom of tank.

7. After the water has been drained, close the drain valve. The air compressor can now

be stored.

NOTE: If drain valve is plugged, release all air pressure. The valve can then be removed,
cleaned, the reinstalled.

SERVICE AND ADJUSTMENTS

ALL MAINTENANCE AND REPAIR OPERATIONS NOT LISTED MUST BE PERFORMED
BY TRAINED SERVICE TECHNICIAN.

Risk of Unsafe Operation. Unit cycles automatically when power is on.
When servicing, you may be exposed to voltage sources, compressed air, or moving
parts. Before servicing unit unplug or disconnect electrical supply to the air compres­sor, bleed tank of pressure, and allow the air compressor to cool.

TO REPLACE REGULATOR (FIG. 5–9)

1. Release all air pressure from air tank. See To Drain Tank in the Maintenance section.

2. Unplug unit.

3. Remove the console cover (N).

4. Using an adjustable wrench remove the safety valve (H) from the regulator manifold

(G).

5. Remove the hose by removing the hose clamp (L). NOTE: The hose clamp is not reus-

able. You must purchase a new hose clamp, see Replacement Parts in the Service
section or purchase a standard hose clamp at a local hardware store.

6. Remove three pump mounting screws (O) securing pump..

7. Carefully lift pump up away from brackets and out of the way.

8. Using an adjustable wrench remove the regulator manifold (G).

9. Apply pipe sealant to new regulator manifold and assemble, tighten with wrench.

10. Reapply pipe sealant to safety valve.

11. Reassemble all components in reverse order of removal. Make sure to orient gauges

to read correctly and use wrenches to tighten all components.

STORAGE

Before you store the air compressor, make sure you do the following:

1. Review the Maintenance section on the preceding pages and perform scheduled

maintenance as necessary.

2. Drain water from air tank. See To Drain Tank under Maintenance.

Water will condense in the air tank. If not drained, water will corrode
and weaken the air tank causing a risk of air tank rupture.

3. Protect the electrical cord and air hose from damage (such as being stepped on or run

over). Wind air hose loosely around the compressor handle. Wrap electrical cord onto
the cord wrap.

4. Store the air compressor in a clean and dry location.

SERVICE

REPLACEMENT PARTS

Use only identical replacement parts. For a parts list or to order parts, visit our service web­site at www.servicenet.bostitch.com. You can also order parts from your nearest
BOSTITCH Factory Service Center or BOSTITCH Authorized Warranty Service Center. Or,
you can call our Customer Care Center at 1-800-556-6696.

SERVICE AND REPAIRS

All quality tools will eventually require servicing and/or replacement of parts. For information
about BOSTITCH, its factory service centers or authorized warranty service centers, visit our
website at visitar www.BOSTITCH.com or call our Customer Care Center at 1-800-556-6696.
All repairs made by our service centers are fully guaranteed against defective material and work

­manship. We cannot guarantee repairs made or attempted by others.
You can also write to us for information at Bostitch Fastening Systems, 701 E. Joppa Road,
Towson , MD 21286 - Attention: Product Service. Be sure to include all of the information shown
on the nameplate of your tool (model number, type, serial number, etc.).

FIG. 1

RIESGO DE ROTURA. LA OXIDACIÓN DEL
TANQUE PUEDE PROVOCAR UNA
EXPLOSIÓN. DESAGOTE EL TANQUE
DESPUÉS DE CADA USO. INCLINE EL
TANQUE PARA DESAGOTARLO
COMPLETAMENTE.

RISQUE DE RUPTURE.

UN RÉSERVOIR
ROUILLÉ PEUT EXPLOSER. VIDER LE
RÉSERVOIR APRÈS CHAQUE
UTILISATION. INCLINER LE RÉSERVOIR
POUR LE VIDER COMPLÈTEMENT.

N154513

ADVERTENCIA AVERTISSEMENT

WARNING

RISK OF BURSTING. RUSTED TANK CAN

CAUSE EXPLOSION. DRAIN TANK AFTER
EACH USE. TILT TANK TO FULLY DRAIN.

FIG. 10

K

M

FIG. 3 FIG. 4 FIG. 5

N

H

FIG. 6

L

FIG. 7

O

FIG. 8

G

Pump shown
moved out of
the way

Vue de la
pompe
déplacée

Se muestra
con la bomba
retirada

FIG. 9

FIG. 2

D

H

I

E

G

F

G

J