Boss Audio Systems RDS740UA User Manual

1

Thank you for purchasing this car audio product.
Please read this manual carefully before operating this car audio product.
Please keep this manual for future use. It will be helpful to you if you are encounter any
operational problem.

WARNING!

To reduce the risk of fire or electric shock, do not use the unit in the rain or moisture
environment.

To prevent direct exposure to laser beam, do not try open the enclosure.
Visible and invisible laser radiation when open and interlocks defeated.

To protect our environment, do not dispose of electrical equipment in the domestic waste.
Please return any electrical equipment that you will no longer use to the collection points
provided for their disposal.
This helps avoid the potential effects of incorrect disposal on the environment and human
health. This will contribute to the recycling and other forms of reutilization of electrical and
electronic equipment. Information concerning where the equipment can be disposed of can
be obtained from your local authority.

Selecting fine audio equipment is only the start of your musical enjoyment.
Now it is time to consider how to maximize the enjoyment you will get from knowing how to
work your new car stereo receiver.

We hope you enjoy using this product and encourage you to always listen at a moderate, safe
sound level to avoid any possible hearing damage or loss.
If you listen to excessively loud sound over time, your hearing can adapt to higher volumes and
what sounds "normal" to you may be quite harmful and can cause you to have permanent
hearing loss. So please practice "safe sound" and always listen at moderate sound levels only.

Start with your volume control at the lowest setting, and slowly increase the level until you can
hear it comfortably and clearly, free from distortion.
Once you have established this comfortable sound level, leave it there.

Preface

2

LOCATION AND FUNCTION OF CONTROLS

4

12

10

14

911

3 2

21

2322

15

181917

8 7

16 13

5

EJ

20

1

1. OPEN BUTTON

2. SEL BUTTON AND VOL KNOB

3. POWER BUTTON

4. LCD DISPLAY
5&6. >>| and |<< BUTTON

7. BAND BUTTON

8. MODE BUTTON

9. MUTE BUTTON

10. INFRARED REMOTE CONTROL SENSOR

11. AS/PS BUTTON

12. TOP/>||,INT,RPT,RDM
and 1-6 NUMBER BUTTON

13. AF BUTTON

14. PTY BUTTON

15. TA BUTTON

16. CLOCK BUTTON

17. SCAN BUTTON

18. AUX INPUT JACK

19. USB SOCKET

20. EJECT BUTTON

21. CD SLOT

22. FLASHING LED

23. RESET BUTTON

6

3

16

BASIC OPERATION:

1. To turn on/off the unit

Press any button except the EJECT and REL button to turn on the unit. It also can
turn on the unit to insert disc or USB. Press the power button and hold for more than

0.5 seconds to turn off the unit.

2. To select playback mode

Press MODE button to select a different mode of operation as indicated on the display
panel. Available modes include Tuner, CDP, USB and AUX.

3. To adjust the volume level

To increase the volume, rotate the volume knob clockwise. To decrease the volume,
rotate the volume knob counter clockwise. When the volume is adjusted, the volume
level will be shown on the display panel.

4. To mute or resume the sound

Press MUTE button momentarily to mute the audio volume, and MUTE will flash in
the display. Press the mute button again to restore volume to the previous setting.
To resume the sound immediately, can also press one of the MODE,
BAND, SEL button or rotate the VOL knob.

5. To turn on/off LOUD mode

Press TA button and hold for more than 0.5 seconds to turn on/off LOUD mode.
When turn on the LOUD mode, it will enhance bass level immediately when the bass
is not enough.

5. To display and adjust the clock time
A) RADIO MODE

When RDS DATA is received, press the CLOCK button shortly and repeatedly to
display the following items alternatively:

--->PS NAME ---> CLOCK --->FREQUENCY --->PTY-->
When RDS DATA is not received, press the CLOCK button shortly and repeatedly
to display the following items alternatively:

--->FREQUENCY ---> CLOCK --->PTY-->
B) USB or DISC MODE
Press the CLOCK button shortly to display time for 5 seconds, and then it returns
to its previous display unless the button is pressed again.
C) time adjustment
In the clock mode, press CLOCK button and hold for more than 1 second to flash
time and then rotate VOL knob to adjust hour or minute.

6. To select and adjust the mode of the sound and menu

A) To select and adjust the sound mode:
Press SEL button shortly and repeatedly to select the mode of VOL(volume),BAS
(bass)(without preset DSP), TRE(treble)(without preset DSP), BAL(balance) and
FAD(fader) in the sequence and circulation. In each mode, the waiting time is about
5 seconds, and when the waiting time is over, it will return to the last display mode.
After select a desired sound item, rotate VOL knob to adjust level of the selected
sound item.

SPECIFICATION

GENERAL
Supply Voltage DC 12 V. Negative Ground
Current Consumption Max.10A
Power Output 80Watts X 4 (Measured at DC 14.4 V)
Number of channels 2 STEREO channels.
Unit Dimensions 178[W] X 165[D] X 50[H] mm.

FM SECTION
Frequency range 87.5MHz -108MHz
Effective sensitivity 3uV.
I.F Frequency 10.7MHz.

RCA LINE OUT
Output 1200mV @ CD MAX.

CD PLAYER
System MP3 Audio System.
Suitable CDs MP3, WMA, CD,CD-R,CD-RW Disc
Frequency characteristics 20Hz-100Hz < 5dB

\

10KHz-20KHz < 5dB.

\

S/N Ratio to CD 50dB [1KHz]

15 4

B) To select and adjust the menu mode:
Press SEL button and hold for more than 2 seconds to turn on TA SEEK/TA ALARM
mode, then press SEL button shortly and repeatedly to select PI SOUND/PI MUTE,
RETUNE L/RETUNE S, MASK DPI/MASK ALL, BEEP 2ND/BEEP ALL/BEEP OFF,
SEEK1/SEEK2(in RADIO mode), DSP OFF/FLAT/POP M/CLASSICS/ROCK, LOUD
OFF/LOUD ON, SUBW OFF/ON, STEREO/MONO(in RADIO mode), DX/LOCAL (in
RADIO mode), VOL LAST/VOL ADJ(When it is in VOL ADJ mode, the next mode will
be A-VOL after VOL ADJ mode, then you can adjust the volume level. The minimum
value of the volume level you can set is 10) and ESP6/ESP25 in the sequence and
circulation. After selecting the desired mode, rotate VOL knob to select one setup item
of the desired mode.

1) TA SEEK/TA ALARM:
TA SEEK mode: when newly tuned station does not receive TP information for 5
seconds, the radio retunes to next station which has not the same station(PI) as the
last station, but has the TP information.
When TP information is absent from the current station for retune time selected
(between 60 & 90 seconds), the radio searches for the next station with the same PI.
If this is unavailable, the search for the next TP station is made.
TA ALARM mode: when this mode is selected, any automatic retune mode is not
activated. Only double beep sound(ALARM) is out-put.
When newly tuned station does not have TP info for 5 seconds, the radio beeps.
When TP information is missing from the current station for retune time, beeps will
be heard.
When newly tuned station does not have RDS signal, PI SEEK will pause.

2) PI SOUND/ PI MUTE:
PI SOUND mode: If a car is cruising between buildings, an oscillation phenomenon
may occur, due to different PI codes being received from the same AF.
PI MUTE mode: In above situation, the sound will be muted for less than 1 second.

3) RETUNE L / RETUNE S:
The initial time of automatic TA search or PI SEARCH mode is selected.
When PI information is not received for retune time, the radio will search for the next,
same PI station.
When same PI station is not received during 1 cyclic search, the radio will switch to
the last station and wait 4-5 minutes for PI code.
RETUNE L mode: selected as 90 seconds.
RETUNE S mode: selected as 60 seconds.

4) MASK DPI/MASK ALL:
MASK DPI mode: only AF which has different PI is masked.
MASK ALL mode: AF with different PI and NO RDS signals with high field strength
levels are masked.

5) BEEP 2ND/BEEP ALL/BEEP OFF:
BEEP 2ND mode: the beep is only generated when an allotted double key is pressed
long(1second).
BEEP ALL mode: the beep is generated when every key is pressed(except power and
release buttons).
BEEP OFF mode: the beep is disabled.

6) SEEK1/SEEK2:
SEEK1: pressing and holding UP/DOWN buttons will search for strong signal stations,
and will stop at the first strong signal.
SEEK2: pressing and holding UP/DOWN buttons will enter search mode, and will only
stop searching when the button is released.

TROUBLE SHOOTING

Before using the check list please make all the connections first.
If you still have questions after going through the checklist, please consult
your local customer service representative.

Common Symptoms

There is no power.

The CDs cannot
be loaded.

Cause

The fuse has blown.

Presence of CD disc inside the player

Inserting the disc in upside down

The surface of CD is extremely dirty
or it is damaged.

Temperature inside the car is too
high.

The volume control is set too low.

There is no sound.

The operation keys
do not work

The sound of the
CD player skips

The antenna cable is not connected. Insert the antenna cable firmly into the

antenna socket of the device.

No radio reception.

1.The built-in microcomputer is not
operating properly due to noise

2.Front panel is not properly fix into
its place

1. Switch the device off and on again. Or press
the RESET button to resume the program.

2. Reinstall the front panel

The device has not been correctly
connected.

The installation angle is more than
30 degrees

Wait until the road becomes smoother before
playing the CD.

Adjust the installation angle to less than 30
degrees

Turn up the volume properly.

Check the power and earth connection
according to the wiring diagram.

Cool off until the ambient temperature returns
to normal

Clean the CD or try another CD, if this works
correctly, the first CD is properly damaged.

Insert the compact disc with the label facing
upward

Remove the disc in the player then put a new
upward

Replace another fuse according to the wiring
diagram.

The car ignition is switched off.

If the power supply is properly connected to
the car accessory, switch the ignition key to
ON or " ACC " " " .

Solution

The device does
not work correctly
(EJECT, LOAD,
PLAY)

In automatic search
mode the radio does
not stop at a trans­mitting station.

Tune in to a radio station manually.The transmission signals are too

weak.

The CDs are loaded
only halfway into
the CD tray.

The transport screws have not been
removed.

Remove the transport screws before using.

The surface of the road is uneven.

The surface of CD is extremely dirty
or it is damaged.

Clean the CD or try another CD, if this works
correctly, the first CD is properly damaged.

5 14

8. To reset the unit

When the LCD displays wrongly or some function knobs are disable, press the
REL button to flip down the front panel and then take it away from the unit chassis.
Push the RESET button with one needle analog to reset the distorted program to zero.

9. To take away the front panel

Press the REL button to flip down the front panel and then take it away from the
head unit. And the anti-theft LED indicator will flash all the time till the front panel
is assembled back to the head unit.

RADIO OPERATION:

1. To select radio band

In RADIO mode, press the BAND button shortly and repeatedly to select your desired
radio band in sequence and circulation as follows:

-->FM1-->FM2-->FM3-->

2. To select the radio station manually or automatically

Under RADIO mode, short press >>| or |<< button and repeatedly to manually tune
up or down for the desired radio station step by step. Long press >>| or |<< button
to automatically tune up or down for the radio station of strong signal.

3. To store the current station or turn on the preset station

In RADIO mode:
A) Press one of 1-6 number buttons and hold for more than 1 second until the second
beep output to store the current station in the preset memory bank of the number
button for the current band. The unit can store 30 preset stations.
When a RDS station is being stored, PI, PS, AF list are stored.
B) Press one of 1-6 number buttons shortly to turn on the preset station stored in the
preset memory bank of the number button for the current band.
In case of RDS mode, the strongest AF is turned on after AF searching.

4. To automatically store for the strongest stations and scan for each stored stations

In RADIO mode:
A) Long press the AS/PS button, it will search from the current frequency and check
the signal strength until 1 cycle search is finished on current band, and then 6
strongest stations will be preset to the corresponding preset memory banks of the
6 number buttons. When the auto-storage operation is completed, it will turn on
the preset station stored in the memory bank of the 1 button.
B) Short press the AS/PS button to scan for each preset station for the current band.
When the field strength level is higher than the threshold level, the radio will stop
at that preset station for 5 seconds, memory and frequency will flash on the LCD
screen, and then the radio will begin scanning again.
In FM band, FM1, FM2 and FM3 is checked one at a time.

ÒÉÄѽâ³ý

CARE FOR USING CD'S:

1. To keep the disc clean:

Before playing a disc, wipe it off with a clean, dust-free cleaning cloth.
Wipe the disc outwards from the disc center.

2. When one has already been inserted. Doing so may damage the unit

Do not attach any sticker or adhesive tape on the disc.

Handle the disc by its edge to keep the disc clean and do not touch the surface.

. Insert a disc

with labeled surface up, or it will damage the unit.

3. Do not expose the disc to direct sunlight or nearby heat sources such as heating
vents, caliduct which can cause the disc to warp.
Do not leave disc in a car if it is parked in direct sunlight as that will lead to a
considerable rise in the temperature inside the car.

4. Do not use any secondhand or rented disc, usually, there is glue on the surface of
those discs, it will stop the unit working and damage it.

5. Always store the disc in its case for protection. Scratched up discs will produce poor
sound performance and cause CD player to skip.

6. In raining day or wet area, the moisture may form on the disc or the optical parts,
The playback may not be possible. If moisture forms on the disc, wipe it off with a
soft cloth.
If moisture forms on the optical parts of the unit, allow the unit to sit for about one
hour with power on.

7. Do not use solvents such as benzine or thinners. Commercially available cleaners
or anti-static spray will damage the unit.

About CD-R/CD-R/W discs:
In addition to commercially-recorded audio CD's, this unit can play CD-R and
CD-R/W discs. In come cases, particularly when recorded on older CD burners,
some CD-R and CD-R/W discs may not play. Also, whenever you are recording
a CD for playback in this receiver, it is recommended that you record at 24x or
slower speed for CD-R and 4x or slower for CD-R/W to achieve higher signal
quality and better playback performance.

13 6

5. To scan for strong signal of radio station

Press the SCAN button to scan the radio frequency.

6. To tune for RDS station

Press PTY button shortly and repeatedly to select one of the following mode:
PTY MUSIC group- - PTY SPEECH group- - PTY OFF
While selecting PTY TYPE, its selection is implemented by preset buttons (press
one of the 6 preset buttons shortly and repeatedly to select the PTY TYPE in the
preset button) as follows:
PTY music group ------------------PTY speech group --------------- OFF

1. POP M, ROCK M 1. NEWS, AFFAIRS, INFO

2. EASY M, LIGHT M 2. SPORT, EDUCATE, DRAMA

3. CLASSICS, OTHER M 3. CULTURE, SCIENCE, VARIED

4. JAZZ, COUNTRY 4. WEATHER, FINANCE, CHILDREN

5. NATION M, OLDIES 5. SOCIAL, RELIGION, PHONE IN

6. FOLK M 6. TRAVEL, LEISURE, DOCUMENT
When PTY MUSIC or PTY SPEECH is on, the previous PTY program and PTY word
is displayed on LCD. If there are no keys entered for 2 seconds, previously selected
PTY is searched. During 1 loop, if desired PTY is not found, NO PTY is flashed, then
return to previous normal radio and PTY word disappear.

7. To alternate the weak signal of RDS station with a strong one

When pressing the AF button briefly, AF switching mode is selected and the state of
AF switching mode is displayed by AF segment in display.
Segment off: AF switching mode off.
Segment on: AF switching mode on, and has RDS information.
Segment flashing: AF switching mode on, but RDS information is not received yet.
When AF switching mode is selected, the radio checks the signal strength of AF all
the time. The interval of checking time of each AFs depends on the signal strength of
current station, from a few minute for strong station to a few seconds for weak station.
Every time that new AF is stronger than current station, it switches over to that
frequency for very short time, and NEW FREQUENCY is displayed for 1-2 second.
Because the mute time of AF switching or checking time is very short, it is almost
inaudible in case of normal program. (When AF flash on LCD, it will search for RDS
station. If AF and TP flash on LCD, it can only search for traffic announcement station).
During FM mode, when AF is on, SEEK, (SCAN), AUTO-MEMORY function can only
receive and save RDS program.
When pressing and holding the AF button, AF mode is converted to REGION ON/OFF
mode.
REGIONAL MODE ON:
AF switching or PI SEEK is implemented to the station which have all PI codes are
same as current station.(PI CODE is checked when AF CHECK in progress)
REGIONAL MODE OFF:
The regional code in the format of PI code is ignored when AF switching or PI SEEK
is implemented.(PI CODE and COVERAGE AREA is not checked when AF CHECK
in progress)

If a valid signal has been
detected, the current frequency will hold and blink for 5 seconds. Press this button
again within 5 seconds to stop scanning and confirm the current desired frequency,
otherwise the radio will revert to scanning for other radio frequencies.

EJ

INSTALLATION INSTRUCTION

This is an anti-theft installation method.
The main unit wears a METAL MOUNTING SLEEVE.
Please connect the wiring, eg, the Power Supply, the Speakers and the Antenna
according to the requirements of this Instruction Manual, then install the metal
mounting sleeve into the car as per the diagram illustrated below.

METAL SUPPORT STRAP

To boost up the capability of anti-jamming,
please make sure fix tightly the metal support
strap into the metal joint that connect to the
chassis of the car.

To properly fix the meal mounting
sleeve, bend the tabs of the sleeve
against the DASHBOARD with
a screwdriver.

METAL MOUNTING SLEEVE

DASHBOARD

FRONT PANEL

PLASTIC TRIM RING

UNIT CHASSIS

NOTE

To attach the removable faceplate back to
the unit chassis, firstly join the left guide
block hole to the left cylinder, then join the
right guide block hole and the right
cylinder, finally flip the front panel up to
combine with chassis.

Before mounting and operating
the CD player, remove the metal
mounting sleeve illustrated by the
arrows.

Remove the two screws that
fix the CD deck mechanism
player during transportation
before mounting the player.

RESET BUTTON

Push this reset button with a cuspidal
object to renovate the distorted program
once the program is distorted.

To remove the front panel,
after flipping down the front
panel, push it rightwards
firstly, then draw the left of
the front panel outwards.

EJECT (EJ) BUTTON

To remove the unit out of the metal mounting sleeve,
insert the two supplied KEYS into the left and right side
slots of the chassis at the same time. Then pull the chassis
out of the metal mounting sleeve as shown in the right
illustration.

Before inserting or ejecting disc, press
the REL button to flip down the faceplate.

7

12

8. To tune for a station with the traffic announce ment

A) When press the button, it is activated as TA mode on or off.
When TA mode is on(TA is displayed on LCD), it will begin to seek TA station and
TA SEEK will be displayed on LCD for a while.
When traffic announcement is transmitted:

1) If the unit is in disc mode, it will switch to radio mode temporarily.

2) Temporarily switch over to an EON linked station when EON detects a traffic
announcement on that other program, and TP will be displayed on LCD.

3) If volume level is below 20, volume level is raised to 20, and returns to its previous
mode and volume level when the traffic announcement is over. If volume is adjusted
during traffic announcement, only the traffic announcement volume is valid.
* TA interruption function:
The current traffic announcement is cancelled by pressing this key. But the TA mode
will not be off.
* When TA is on, SEEK, (SCAN), AUTO MEMORY function can be received or saved
only when traffic program identification code has been received.
When TA is ON, traffic program identification code is not received during specified
time.
B) When pressed and held, EON TA LOCAL/ EON TA DISTANCE mode is selected.
The purpose of this mode is to reduce unwanted interference caused by EON TA
switching due to weak signal strength, resulting in the radio being switched back to
the current tuned station, or being muted.

1) EONTA LOCAL mode:
When the field strength level of EON linked stations is below the threshold level,
the radio will not switch to that station, avoiding unnecessary interference.
When EONTA LOCAL mode is selected, EONTA LO on numeric display is indicated
for a few seconds.

2) EONTA DISTANCE mode:
EON TA switching will be determined by the information of the current station. When
EONTA DISTANCE mode is selected, EONTA DX on numeric display is indicated for
a few seconds.

USB or DISC OPERATION:

1. To load/unload disc

Press the REL button to flip down the front panel and then insert the disc into the disc
compartment or press the EJ button to eject the disc from the disc compartment.

2. To load/unload USB storage

Insert the USB storage into USB socket, then the playing mode will be changed into
USB mode and display USB on LCD, and then play the first track of USB.
NOTE: Always remember to switch off the unit’s power or switch to other mode then
remove out the USB Stick. Never try removing the USB Stick while playing music file
on the USB stick. It may damage the USB stick and sometimes will cause the unit
system lock up.

WIRING CONNECTION

++

++

++

++

Yellow

Antenna Socket

Constant

12 Volts

Ground

Ignition Switch
12 Volts

Front

Rear

Right

Speaker

Power Antenna/Remote Amp Turn On
(Blue)

Front

White

White/black

Green/black

Violet/black

Gray/black

Gray

Violet

Green

Rear

Left

Speaker

10A FUSE

FILTER
BOX

0.5A FUSE

Note:

1. Make sure use a speaker with 4 ohm load impedance.

2.

3. Front AUX IN and rear AUX IN can not be connected to at the same time.

Do not touch the auto antenna wire and the ground wire touch each other.

RCA output

RCA output

Front (Black)

Rear (Gray)

Subwoofer output

Yellow

Red R

Red R

Red R

White L

White L

White L

AUX iutput

Brown

ISO Connector

Black

Red

3. To select next or previous track to play
Under USB or disc mode, press the >>| button to select next track to play.
Press the |<< button within 1 seconds after selecting a track to select the previous
track to play. Press the |<< button 1 seconds later after selecting a track to select
the current track and play from the beginning of the current track.

4. To select next or previous 10 track to play for USB or MP3/WMA

Under USB or MP3/WMA mode, short press M6 or M5 button to select next or
previous 10 TRACK during normal play.

5. To play fast forward or backward

Under USB or disc mode, during playback, press the >>|/|<< button and hold to skip
forward or backward.

6. How to use the PLAY/PAUSE/TOP button

Under USB or disc mode, during playback, press PLAY/PAUSE/TOP button to pause
USB or disc playback, press again to resume USB or disc playback.
Press this button and hold for more than 0.5 seconds to play the first track of the USB
or disc.

7. To scan tracks

Under USB mode, press INT button shortly to display M-INT and play the first 10
seconds part of each track of all.
Under CD/MP3/WMA disc mode, press INT button shortly to display S-INT and play
the first 10 seconds part of each track of all.
Under USB or MP3/WMA disc mode, press INT button long to display D-INT and play
the first 10 seconds part of each in current folder.
Under INT mode, press INT button again to stop INT mode and retain playing the
track currently selected.

8. To repeat track(s)

Under USB mode, press RPT button shortly to display M-RPT and play the current
track repeatedly.
Under CD/MP3/WMA disc mode, press RPT button shortly to display S-RPT and play
the current track repeatedly.
Under USB or MP3/WMA disc mode, press RPT button long to display D-RPT and
play the current folder repeatedly.
During RPT mode, press RPT button again to cancel RPT mode.

9. To play tracks in random

Under USB mode, press RDM button shortly to display M-RDM and play the track of
all in random order.
Under CD/MP3/WMA disc mode, press RDM button shortly to display S-RDM and play
the tracks of all in random order.
Under USB or MP3/WMA disc mode, press RDM button long to display D-RDM and
play the tracks in the current folder in random order.
Under RDM mode, press RDM button again to cancel RDM mode.

An insulation tag was installed in your remote by the manufacturer to prevent the
battery from draining. Removing the tag from the remote before using.

BATTERY INFORMATION:

Lithium Battery: CR2025 3V
Battery Life: Approximately 6 months.

Replacing the Battery from the Remote Controller:

1) Remove the battery holder by pressing the locking tab with your thumb
and pulling it out.

2) Replace the battery with the same type and the “ side facing up.

3) Gently push in the holder until securely locked into place.

WARNING:

+”

Do not recharge, disassemble or dispose of in fire.

Battery leakage may cause damage to the unit.

To avoid the risk of accident, keep batteries out of reach of children.

MAINTENANCE OF REMOTE CONTROL

+ side up

B

A

11

8

10.To quickly select the track in MP3/WMA format to play
Under MP3/WMA disc mode or USB mode, press AS/PS button repeatedly to select
TRACK SEARCH, FIRST CHARACTER SEARCH or DIRECTORY SEARCH mode.
A) Under TRACK SEARCH mode, the LCD will display TRK T000 and flash the biggest
digit 0 that the USB storage or MP3/WMA disc contain. Then rotate the VOL knob on
the front panel or press the + or - button on the remote controller to select the number
of the flashing digit from 0~9. Then press SEL button to confirm the number and flash
next smaller digit 0. With the same means, select the number of the flashing digit.
After finishing selecting the number of all flashing digit, press SEL button to play the
track of the selected serial number.

B) Under FIRST CHARACTER SEARCH mode, the LCD will display A--......, If there are

files names its first character are A , the ......is the first file name its first character is

A by the order of A~Z and 0~9; otherwise, the ......is NONE. Rotate the VOL knob or

press the + or - button to select file s first character by the order of A~Z and 0~9.
Then press the >>|/ |<< button to select one file its first characters is the selected one.
Finally press SEL button to play the selected file.
C) Under DIRECTORY SEARCH mode , the LCD will display the root folder(if there is
not the root folder, it will find a root folder named ROOT). Then rotate VOL knob or
press the + or - button to select your desired folder and then press the >>|/|<< button
to select your desired track in the folder. Finally press the SEL button to play the
selected track.

11.To display ID3 information
Under USB or MP3/WMA disc mode, if you press BAND button repeatedly, the file
name, folder name, song’s title, artist and album information will be scrolling on the
LCD display. As long as the current playing MP3/WMA music contains relevant ID3
tag information in version 1.0/2.0 format, the 3 items underlined above will be
scrolling on the LCD display. Otherwise, they will not.

12.To play CD/MP3/WMA format-mixed disc

Under CD & MP3 & WMA format-mixed disc playback mode, pressing BAND button
and hold for more than 0.5 seconds it will change between the playing the CD and
MP3/WMA formatted songs.

1. Power On/Off.

2. Mute Button

3.

4.

5. SEL/MENU

Loudness Button

Audio Level & Menu UP(+) Button

Button

6. Audio Level & Menu Down(-) Button

7. MO/ST Button

8. AP/PS Button

9. Band Button

10. Mode Button

11.Tune/Seek Up And Track Skip Up/FF Button

12.Tune/Seek Down And Track Skip Down/REW Button

13.SCAN Button

14. Clock Display /Setting Button

15. LOC/DX Button

16. CD Track TOP/>||/Radio Preset 1

17. CD Track INT/Radio Preset 2

18. CD Track RPT/Radio Preset 3

19. CD Track RDM/Radio Preset 4

20. Radio Preset 5

21. Radio Preset 6

OPERATION OF REMOTE CONTROL

4

6

8

14

16

18

20

7

11

15

19

21

1

5

3

13

12

10

9

17

2

9

10