Boss Audio 614UA User Manual

CAR MP3 PLAYER / RECEIVER WITH USB/SD/MMC INTERFACE

LOUD LOC

SOURCE /

DISPLAY BUTTON

INFRARED

REMOTE SENSOR

LCD

DISPLAY

BAND /

AMS

BUTTONS

USB PORT

TUNING /

SEEK / TRACK

UP/DOWN

NEXT/BACK

BUTTON

POWER / SELECT

VOLUME

KNOB

RANDOM BUTTON

PLAY/

PAUSE

BUTTON

REPEAT

INTRO

BUTTON

SCAN

BUTTON

PRESET MEMORY STATION BUTTONS

10+/- FOLDER

RANDOM

(M1-M6)

BUTTON

UP / DOWN

BUTTONS

SD/MMC

CARD

SOLT

FUNCTION OF REMOTE CONTROL

AUX-IN

JACK

INSTALLATION

-Before finally installing the unit, connect the wiring temporarily and make sure it is all connected up properly and the unit and system work properly.

-Use only the parts included with the unit to ensure proper installation. The use of unauthorized parts can cause

-Consult with your nearest dealer if installation requires the drilling of holes or other modifications of the vehicle.

-Install the unit where it does not get in the driver's way and cannot injure the passenger if there is a sudden stop, like an emergency stop.

-Avoid installing the unit where it would be subject to high temperature, such as from direct sunlight, or from hot air, from heater, or where it would be subject to dust dirt or excessive vibration.

DIN FRONT/REAR-MOUNT

This unit can be property installed either from Front (conventional DIN Front-mount) or Rear (DIN Rear-mount installation, utilizing threaded screw holes at the sides of the unit chassis). For details, refer to the following illustrated installation methods A and B.

- DIN FRONT-MOUNT (Method A)

Installation the unit

182

1. Dashboard

2. Holder After inserting the half sleeve into the dashboard, select the appropriate tab according to the thickness of the dashboard material and bend them inwards

- DIN REAR-MOUNT (METHOD B)

Installation using the screw holes on the sides of the unit. Fastening the unit to the factory radio mounting bracket.

to secure the holder in place.

Removing the unit

a. Frame b. Insert fingers into the groove in the front of frame and pull out to remove the frame. (When reattaching the frame, point the side with a groove down wards and attach it.) c. Insert the levers supplied with the unit into the grooves at both sides of the unit as shown in figure until they click. Pulling the levers makes it possible to remove the unit from the dashboard.

E - 1

1. Select a position where the screw holes of the bracket and the screw holes of the main unit become aligned (are fitted) and tighten the screws at 2 places on each side.

2. Screw

3. Factory radio mounting bracket.

4. Dashboard or Console

5. Hook (Remove this part) Note: the mounting box, outer trim ring, and half-sleeve

are not used for method B installation.

malfunctions.

ELECTRICAL CONNECTION

a. Make sure your car battery is a 12 volt (6 filler caps) negative ground system (if not, a converter will be necessary). b. Before starting wiring connections, disconnect the power supply by removing the fuse from fuse box at rear side. c. Connect the power wire to one of the extra terminals of the fuse box ISO connector harness provided. d. Connect the black ground wire to a metal part of the car. It is important to make good contact. e. Make other wiring connections as shown. Plug ISO connector harness to ISO connector and plug fuse to fuse box at

rear side.

f. If your car does not have ISO connector, you can procure it from any car accessory shop.

NOTES: INCORRECT WIRING OR OPERATION WILL AVOID THE WARRANTY OF THIS UNIT.

Fuse Replacement: To replace the fuse, pull out the blown fuse from the socket. Insert a new one with same rating,15A

GENERAL OPERATION

POWER ON/OFF

Press any button to turn on The unit. Long press the knob to turn power off.

AUDIO AND AREA SETTINGS

You can select the following settings by pressing the KNOB ONCE. Rotate it to adjust: BASS (BAS)-> TREBLE (TRE)-> BALANCE (BAL)-> FADER (FAD)->LOUD(LD ON/OFF)

->EQ (PO/ROCK/CLASSIC/EQ OFF)->BASS (BAS)->DX/LOC->STERO/MONO(STE/MO)

->Frequency Area (USA/EUR)

- LOC / DX MODE

Use this mode to change between Local and Distant (DX) tuning mode. Local mode improves reception in some areas where the signal is too strong.

- FM MONO / STEREO BUTTON (MONO)

Use this control to select stereo or monaural reception for FM radio stations. You can sometimes improve reception of distant stations by selecting mono mode.

- CLOCK DISPLAY AND ADJUST

LONG PRESS DISP(SRC)button to display clock. LCD will display clock for 3-4 seconds and then resume to display current playing status (e.g. Frequency of Radio/AUX/Music information of USB/SD-MMC mode) When LCD is displaying clock, press DISP(SRC)button and clock digit will flash. Rotate knob to adjust. Press the knob again to switch between hours and minutes digits. Press DISP(SRC)button to confirm adjusted time.

E - 2

- SWITCHING BETWEEN USA AND EUROPE FREQUENCY

While LCD displays USA or EUR rotate volume knob to switch between USA and EUR (Europe)frequency. Leave it For 3-4 seconds until current frequency menu resumes or press any button to Continue operation. Every time desired area frequency is selected, frequency and Turning step will be switched to corresponding settings automatically.

- EQ SETTINGS EQ OFF->ROCK->CLASSIC->POP

At EQ off mode preset equalizer will be controlled by Bass / Treble setting.

VOLUME KNOB

When the settings function is not activated, rotate the knob to adjust volume level.

SOURCE(SRC) BUTTON

Press this button to select different sources, sequence as follow:

A) Tuner mode (Radio) C) USB (only if a USB drive is inserted) D) SD / MMC (Only if a SD or MMC card is inserted) E) AUX IN

SOURCES　PRIORITY

Whenever a USB or SD/MMC is being inserted, unit will automatically switch to USB or SD/MMC mode, does not matter the unit is currently in what mode.

When in USB or SD / MMC mode, if the USB or SD / MMC is being removed, unit will automatically switch to radio mode.

FRONT AUX INPUT

Connect the external device to the front 3.5mm jack on front panel, Press SRC button to select AUX IN mode, At AUX IN mode, LCD displays AUX.

TUNER MODE (RADI0) OPERATION

FRONT CABINET

LEFT TRACK

RIGHT TRACK

GROUND

AUX IN

AUTO MEMORY STORE (AMS)

AUTO MEMORY STORE: long press BAND AMS button to enter auto store mode. The radio will automatically search and store stations to the preset memories of the band. To stop auto store, press AMS button again.

TUNING UP / DOWN BUTTON ( )

Press these buttons once to auto scan for next station. Long press to tune radio frequency manually.

CHANGING BAND

Press BAND AMS button to change between FM and AM bands F1,F2,F3, A1(M1),A2(M2).

E - 3

RESET THE SYSTEM

The RESET button is located on the front panel (as shown on the diagram). Press it vertically with a ballpen or metal object will activate it. The reset button function is to be activated for the following reasons:

Initial installation of the unit when all wiring is completed. All the function buttons do not operate and reset is necessary. Error symbol on the display and reset is necessary.

Note: If the unit cannot function normally after resetting, please use a cotton swab soaked in isopropyl alcohol to clean the socket on the back of the control panel.

LIQUID CRYSTAL DISPLAY PANEL (LCD)

The LCD panel display the frequency, time and activated functions.

NOTE:

It is a characteristic of LCD panel that if subjected to cold temperatures for an extended period of time, they will take longer time to illuminate than under normal conditions, in addition, the visibility of the numbers on the LCD may slightly decrease. The LCD read-out will return to normal when temperatures increase to a normal range.

STATION PRESET BUTTONS (M1-M6)

You can store & recall six preset radio stations by pressing M1-M6 buttons

TO STORE A STATION: 1) select a band (if needed)

2) select a station by tuning up / down button

3) hold a preset button which you want store the station for at least 2 seconds. The

preset number will appear on the display.

TO RECALL A STATION: 1) select a band (if needed)

2) press a preset button briefly to recall the stored station.

MP3/SD/USB OPERATIONS

M1)PLAY/PAUSE AND FIRST TRACK BUTTON

Press this button briefly to pause MP3 play, press again to release pause.

M2)INTRO SCAN BUTTON

Press this button to select Intro Scan function, the first 10 seconds of each track will be played sequentially until this button is pressed again, then normal play will resume at the current track.

M3)REPEAT BUTTON

Pressing this button will activate Repeat Function in the following order:

RPT ON RPT OFF M4)RANDOM PLAY BUTTON

When random play mode is selected, the tracks will be played in random order, press this key one more time to cancel random play mode.

E - 4

+ 11 hidden pages