How it Works
Boss
Loading...
950
User Manual
19 pgs1.13 Mb0

Boss 950 User Manual

Download
Page 1
USER'S MANUAL
BOSS Beds 950
http://bossbeds.ca
Page 2
http://bossbeds.ca
0608111213
Table of Contents
01
030405
141516
17
Page 3
Safety Disclaimer
In-Home use only
Pacemaker Notice:
This bed base is intended to be used only as described in this manual. Do not use any accessories/attachments that are not recommended by the manufacturer. Close supervision is required when the bed base is used by or near children, convalescents or disabled persons.
Please ensure you connect the base properly to the power supply. Any incorrect power connection may cause electric Shock or Fire. FOR OPTIMAL SAFETY, YOUR ADJUSTABLE BED SHOULD BE PLUGGED INTO A SURGE PROTECTOR (not supplied with this adjustable bed). Always unplug this adjustable bed frame from the electrical outlet before any cleaning or maintenance of the bed frame. To safely disconnect, remove the plug from the outlet. Keep cord away from heated surface. Use only indoors.
The control box, motors, and remote (except battery compartments) should not be opened or tampered with. Opening or tampering with these components without authorization will void the warranty.
This product is designed to be used by an adult. Do not allow children to operate this bed without adult supervision. Immediately dispose of all packing materials as they can pose a smothering risk to children and pets. Injury could occur if children or pets are permitted to play on or under the bed.
Electrical Safety: Connect to a surge protector (not included).
Children and Pets:
http://bossbeds.ca
Bossbeds adjustable bed bases are designed exclusively for in home use only.
Do not use this base with oxygen therapy equipment or near explosive gases.
Thank you for purchasing a Bossbeds adjustable bed base. For your safety, please read all instructions carefully before using this adjustable base. Save these instructions for future reference.
Safety Instructions
Attention:
If the power cord or plug becomes damaged, or if the bed base is wet or not working properly, stop using the bed base and contact customer service
Keep the base unplugged from the electrical outlet before operating any part of the base. To prevent the risk of electric shock, always unplug the base before cleaning. For your safety, ensure the base is in a flat position with all motors turned off, disconnected from the power source, and keep the power cord away from heated surfaces.
This bed base contain noedymium magnets which may interfere with magnetic fields of devices such as pacemakers, ICD'S etc. Some pacemakers may falsely interpret the optional massage vibrations as movement or exercise. The owner of such medical devices should consult their physician before using this product.
Page 4
FCC Compliance:
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
To comply with the FCC RF exposure requirements, no change to the antenna or the device is permitted. Any change to the antenna or the device could result in the device exceeding RF exposure requirement an void user's right to operate the device. Radio Frequency: 2.4GHz
Product Ratings:
The massage function will emit a noticeable tone during operation. As the massage intensity level is increased, the tone will intensify. The volume of this tone is directly related to the location environment. For example, when demonstrated in a show room, the surrounding environmental noise will cover some of massage noise. However, when installed in a home setting with wooden floors, carpeted or not, the massage volume will be more noticeable. In normal base operation, the legs support of the base will create a contact noise with floor. When entering, exiting, or shifting weight on the base, this contact noise may be louder as the legs make contact. This is normal.
Fabric Care:
The lift motors are not designed to operate continuously for more than (2) minutes in an (18) minutes time period. Attempting to circumvent or exceed this rating will shorten the life expectancy of the product and may void the warranty.
http://bossbeds.ca
To prolong the life of your fabric, protect it from direct sunlight whenever possible. For spot cleaning, wipe area with a light damp sponge or vacuum with a soft brush attachment to remove particles. Keep at a minimum of 30cm (12 inches) away from direct heat sources. For deeper cleaning, blot liquid spills with a clean dry cloth. Wipe with a clean cloth dampened with warm water. Do not moisten excessively. A soft bristle brush may be used to remove ingrained soil. Avoid scratching by brushing gently. Wipe with a clean cloth dampened with warm water to remove residues. Dry in a shaded area away from direct heat. If persistent marks remain visible after cleaning, seek professional advice.
Safety Instructions
Weight Limits:
Acoustics:
This product is not rated to support weights exceeding 385 kgs including the mattress and bedding The base will structurally support this weight, provided it is evenly distributed across the bed base. The adjustable base is not designed to support or lift this amount in the head or foot sections alone. Exceeding this weight restriction could damage the bed and/or cause injury and will void the warranty.
Page 5
I)
L)
F)
G)
M)N)O)
O) Audio Cable [1]
D)
A) Wireless Remote Control and AAA batteries [3]
B) Legs and Washers (Note that the legs are two piece legs) [4]
Parts List:
Parts List
I) Long Bolts M8 [4]
C)
K) Small Washers [12]
H) Large Washers [2]
http://bossbeds.ca
F) Headboard Bracket [2]
C) Mattress Retainer [1]
D) Power Supply [1]
E) Power Cord [1]
L) Hex Key [1]
J)
K)
M) Sync Cable [1] (Optional)
A)
B)
G) Headboard T-Bar [2]
J) Short Bolt [8]
N) Long Bolts M10 [2]
H)
E)
Page 6
USB Charge
and Outlet
Sub Speaker
Massage Motors
Under Bed View
Subwoofer
LED Light
Massage Motor
http://bossbeds.ca
Main Speaker
USB Charge
and Outlet
Foot Motor
Head Motor
Massage Motor
Control Box
LED Light
Head Tilt
Motor
Lumbar Motor
LED Light
Page 7
Foot Motor
DC Cord
AC Cord
Wireless
Remote
Control Box
Head Tilt
Motor
Not to Scale, Only for illustration purposes.
Read all illustrations and instructions before beginning the installation process. Head Motor
Led Light
Power Supply
Lumbar Motor
Sync Cable
Electronics Overview
http://bossbeds.ca
Page 8
http://bossbeds.ca
STEP 4: Connect power supply
Plug the power cord into the power supply as shown.
STEP 3: Overturn the bed base carefully
Carefully turn the base over using two people. Do not lay the base on its side to prevent damage to the side button, fabric or legs.
Put the bed base in a desired place with the bottom of the box facing up. Remove box cover, take out all of the packing materials and put aside, Make sure not to puncture the bed with any sharp objects.
Installation
STEP 2: Remove the bed from the box
STEP 1: Remove packing materials
Remove the bed base from the box keeping the bottom of the base facing upwards. Install the 4 legs to the four corners as shown. Tighten the legs by hand. Ensure the legs are secured tightly. P.S. Install the headboard brackets at the same time if attaching to a headboard. See the page 16.
Page 9
After the base is connected to the power supply, install three AAA batteries into the remote battery compartment. See pages 9 and 10 to learn how to operate the remote.
STEP 6: Install mattress retainer
http://bossbeds.ca
Installation
*Locate the mattress retainer as shown below [1)];
Insert the mattress retainer into the hooks at the foot of the bed as shown [2)]. Slide the mattress retainer into place. Ensure it is securely tightened [3)].
STEP 5: Remote
1)
2)
3)
Page 10
Memory B Preset
Under Bed
Light
http://bossbeds.ca
Foot Down
Head Tilt Up
Lumbar Up
Lumbar Down
Head Massage
Intensity
Massage Timer
Foot Massage
Intensity
Head Up
Wireless Remote Control
Remote Overview
Massage Mode
Sets
Flash Light
Head Down
Zero Gravity
Preset Position
Memory A
Preset
Head Tilt Down
Foot Up
Flat
Page 11
Wireless Remote Control
Adjusting Features
The HEAD UP/DOWN button raises/lowers the head section of the base
The FOOT UP/DOWN button raises/lowers the foot section of the base
One touch ZERO GRAVITY preset position, adjust your legs to a higher level than your heart, to help relieve pressure off the lower back and promote body circulation
http://bossbeds.ca
The one touch FLAT button returns the head and foot sections to a horizontal position.
One touch MEMORY A button allows you to preset your favorite postion.
One touch MEMORY B button allows you to preset your favorite postion.
The HEAD TILT UP/DOWN button customizes the level of head support
The LUMBAR UP/DOWN button customizes the lever of lumbar support
Page 12
Turns on/off the light underneath the bed.
Turns on/off the flashlight that is on the remote.
The buttons of 10MIN, 20MIN or 30MIN sets the massage feature to automatically shut off after 10MIN, 20MIN or 30MIN as set.
The MASSAGE model switch button, there are three massage models.
The HEAD button increases or decreases the head massage intensities
The ALL/OFF button shuts off all massage features.
The FOOT button increases or decreases the foot massage intensities
http://bossbeds.ca
Wireless Remote Control
Massage Features
Page 13
Back to POSITIONS page, the smart device can act all functions the same as the remote.
STEP 1:
Search "Bossbeds" in APP Store( for Apple devices) or Google Play( for Android), then install software into the smart device.
Enter into the Settings page after click the setting button on the right of POSITIONS, select the target the bed with the named start of "ORE-******", it will be connected.
STEP 4:
STEP 3:
http://bossbeds.ca
STEP 2:
Open Bossbeds APP, click ( 4M ) BEDDING, will enter into POSITIONS page.
Insure the smart device bluetooth turned on before using APP.
APP Use Guide
Page 14
STEP 2: Audio cable connect to base audio
The USB charge and outlet on both side of head position under the base board can be used normally after the power supply connection.
USB Charge And Outlet Guide
Attention: disconnect the base from power supply and bluetooth connection when not planning to use the audio, USB charge and outlet function.
Audio Cable
http://bossbeds.ca
Press switch button to use the audio cable connect the device to base audio instead of bluetooth. The base speaker shares all device audio synchronously.
Bluetooth to Audio
Cable connection
swift button
Press button
"VOL+" /"VOL-"
increase/reduce the
voice respectively
Turn on smart device bluetooth, search the base signal start the name of "Bed Sound ******" and connect it. The base speaker shares all smart device audio synchronously.
Audio and USB Charge Use Guide
Audio Guide
STEP 1: Bluetooth connect to base audio
Page 15
http://bossbeds.ca
Very important: Pairing your device must be completed within 2 minutes; Make sure the other base in the room is powered off.
Remote Pairing
Attention: All bases are set to the different DIP of the remote for easier use. You need to pair your remote if you need one remote controls two bases simultaneously. If using only one base normally, proceed to page 14.
Press and hold the "LINK BUTTON" on the control box untill the LINK LED fashes, then release the "LINK BUTTON"
STEP 2:
Press and hold simultaneously the Head-Up button and Foot-Up button on the remote control until backlight LED flashes, then release the two buttons
STEP 1:
○
○
Page 16
While the buttons are flashing, press one of these three buttons including "MEMORY A"/"MEMORY B"/"ZG" until the flashing stops. The selected MEMORY FUNCTION is now set.
Memory Setting
Ensure the base is connected to the power supply correctly and the remote control works properly. Ensure the base is in the Flat position. Make sure the massage, LED light and other functions are turned off.
STEP 2:
Adjust the HEAD and FOOT to your desired position. Press the "TIMER/ALL OFF" button until all buttons on the remote are flashing.
STEP 3:
http://bossbeds.ca
STEP 1:
○
○
○
○
Page 17
How to disable the synchronizing function
Remote B
Remote A
http://bossbeds.ca
Use the sync cord connecting base A control box in sync port with base B sync port.
How to synchronize the two bases:
Sync Cord
Unplug the sync cord connecting the two bases. The sync function is now disabled.
After synchronization, any of the remotes can control the two bases synchronously.
How to operate two bed bases simultaneously
STEP 1:
STEP 2:
Sync port: SYNCHRO CNTL!
The sync cord is needed when connecting two CK or TXL bases together.
STEP 3:
Setting Up Two Bases
○
Page 18
http://bossbeds.ca
Open the headboard bracket accessory package and confirm that all the pieces listed below are included: Headboard Brackets [2] Headboard Connecting Components [2] Short Bolts (8) Long Bolts M8 [4] Large Washers [2] Small Washers [12] Hex Key [1] Long Bolts M10 [2]
STEP 3:
STEP 1:
STEP 2:
Headboard Brackets Installation
The remaining 4 pieces of long bolts (M8) and 4 pieces of small washers can be used to attach the headboard bracket to your headboard.
STEP 4
Attach the headboard T-Bar (G) to the headboard bracket(F) using 4 short bolts and 4 small washers as per the picture to the right. Use the Hex Key to tighten the bolts. Repeat this process for the other side of the base.
Install the headboard bracket (F) using one long bolt (M10) and one large washer. Install as per the picture to the right. Use the Hex Key to tighten the bolts. Repeat this process for the other side of the base.
Page 19
http://bossbeds.ca
Trouble Shooting
1
2
Loading...
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use