Bose® SoundLink
®
around-ear wireless headphones II
Owner’s Guide │ Danish │ German │ Dutch │ Spanish │ Finnish │ French │ Italian │ Hungarian
Norwegian │ Polish │ Swedish │ Thai │ Korean │ S. Chinese │ T. Chinese │ Japan │ Arabic
Important Safety Instructions
Please read this owner’s guide carefully and keep for future reference.
WARNINGS
• DON’T use the headphones at a high volume for any extended period.
- To avoid hearing damage, use your headphones at a comfortable, moderate volume level.
- Turn the volume down on your device before placing the headphones on your ears, then turn the volume up gradually
until you reach a comfortable listening level.
• DON’T use your headphones while driving or at any time the inability to hear outside surrounding sounds may present
a danger to yourself or others.
• DO focus on your safety and that of others if you use the headphones while engaging in any activity requiring your
attention, e.g., while riding a bicycle or walking in or near trafc, a construction site or railroad, etc. Remove the headphones or adjust your volume to ensure you can hear surrounding sounds, including alarms and warning signals.
• DON’T use mobile phone adapters to connect headphones to airplane seat jacks as this could result in personal
injury such as burns or property damage due to overheating. Remove and disconnect immediately if you experience a
warming sensation or loss of audio.
• DON’T submerge or expose for extended period to water, or wear while participating in water sports, i.e. swimming,
waterskiing, surng, etc. Exposure to moisture may increase the risk of re or electric shock.
• DON’T use the headphones as aviation communication headsets except in case of emergency.
- No incoming audio will be heard with a discharged or improperly installed battery. This could result in the potential of
missed communications while piloting an aircraft.
- Extremely loud ambient noise levels common to many propeller-driven aircraft may impair your ability to receive
incoming audio communications, particularly during takeoff and climb out.
- The Bose® SoundLink® around-ear wireless headphones II are not engineered for noise conditions, altitude, temperature or other environmental conditions common in non-commercial aircraft, resulting in possible interference to critical
communications.
• DON’T place naked ame sources, such as lighted candles, near the product.
• DON’T make unauthorized alterations to the product; doing so may compromise safety, regulatory compliance,
system performance, and may void the warranty.
WARNING
This product contains magnetic material. Contact your physician if you have questions on whether this might affect the
operation of your implantable medical device.
BATTERY WARNINGS
• The battery pack shall not be exposed to excessive heat such as sunshine, re or the like.
• In the event of a battery leaking, do not allow the liquid to come in contact with the skin or eyes. If contact has been
made, wash the affected area with copious amounts of water and seek medical advice.
• Batteries inside the product need to be charged before use. Always use the correct charger and refer to the manufacturer’s instructions or equipment manual for proper charging instructions.
• DON’T attempt to remove the rechargeable lithium-ion battery from this product. Contact your local Bose retailer or
other qualied professional for removal.
NOTE
Use this product only with an agency approved power supply meeting local regulatory requirements (ex. UL, CSA, VDE,
CCC).
CLEANING
The headphones do not require scheduled cleaning. Should cleaning be necessary, simply wipe the outside surfaces with
a soft cloth.
Bose Corporation hereby declares that this product is in compliance with the essential requirements and other relevant
provisions of Directive 1999/5/EC and all other applicable EU directive requirements. The complete declaration of
conformity can be found at: www.Bose.com/compliance
This symbol means the product must not be discarded as household waste, and should be delivered to an appropriate
collection facility for recycling. Proper disposal and recycling helps protect natural resources, human health and the
environment. For more information on disposal and recycling of this product, contact your local municipality, disposal
service, or the shop where you bought this product.
Please dispose of used batteries properly, following local regulations.
© 2015 Bose Corporation. No part of this work may be reproduced, modified, distributed, or otherwise used without prior written
permission.
2 - English
Important Safety Instructions
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with a dry cloth.
7. Refer all servicing to qualied personnel. Servicing is required when the apparatus has been damaged in any way,
such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the
apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
NOTE:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Changes or modications not expressly approved by Bose Corporation could void the user’s authority to operate this equipment.
This device complies with FCC and Industry Canada RF radiation exposure limits set forth for general population. It must not be
co-located or be operating in conjunction with any other antenna or transmitter.
This Class B digital apparatus complies with Canadian ICES-003. CAN ICES-3 (B) / NMB-3 (B)
This device complies with part 15 of the FCC rules and Industry Canada license-exempt RSS standard(s).
Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation.
Temperature range: Operating: -4°F to 113°F (-20°C to 45°C)
Charging: 41°F and 104°F (5°C and 40°C)
Designed by Bose. Assembled in China.
Date of Manufacture: The eighth digit in the serial number indicates the year of manufacture; “5” is 2005 or 2015.
China Importer: Bose Electronics (Shanghai) Company Limited, Part C, Plan 9, No. 353 North Riying Road, China (Shanghai)
Pilot Free Trade Zone
EU Importer: Bose GP, Castleblayney Road, Carrickmacross, Ireland
Taiwan Importer: Bose Taiwan Branch, Room 905, 9F, Worldwide House, 131 Min Sheng East Rd, Section 3, Taipei, Taiwan,
105
BC
Toxic or Hazardous Substances and Elements
Part Name Lead (Pb) Mercury (Hg) Cadmium (Cd) Hexavalent (CR(VI))
PCBs
Metal parts
Plastic parts
Speakers
Cables
This table is prepared in accordance with the provisions of SJ/T 11364.
O: Indicates that said hazardous substance contained in all of the homogeneous materials for this part is below the limit require-
ment of GB/T 26572.
X: Indicates that said hazardous substance contained in at least one of the homogeneous materials used for this part is above the
limit requirement of GB/T 26572.
The N Mark is a trademark or registered trademark of NFC Forum, Inc. in the United States and in other countries.
The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by Bose
Corporation is under license.
Names and Contents of Toxic or Hazardous Substances or Elements
Polybrominated Biphenyl
X O O O O O
X O O O O O
O O O O O O
X O O O O O
X O O O O O
(PBB)
Polybrominated
diphenylether (PBDE)
English - 3
Contents
ank you .............................................................................................................. 5
Unpacking ............................................................................................................. 5
Headphone components .................................................................................... 6
Charging the battery ............................................................................................7
Battery indicator ...........................................................................................7
Selecting a language for voice prompts ........................................................... 7
Turning voice prompts off/on ................................................................... 8
Pairing a mobile device ...................................................................................... 8
Pairing with NFC .................................................................................................. 9
Playing music ....................................................................................................... 9
Using the headphones with multiple devices ............................................... 9
Disconnecting a Bluetooth® device ......................................................... 10
Reconnecting a previously connected device .......................................10
Scrolling through other paired devices .................................................. 10
Clearing the headphone memory ............................................................ 10
Headphone controls...........................................................................................10
Headphone status indicators ............................................................................ 11
Battery charge level ..................................................................................... 11
Using the back-up audio cable ......................................................................... 11
Troubleshooting ................................................................................................. 12
Battery care ......................................................................................................... 13
Storage ................................................................................................................. 13
Cleaning ................................................................................................................ 13
Replacement parts and accessories ............................................................... 13
Customer service ................................................................................................ 14
Limited Warranty ................................................................................................ 14
Technical information ........................................................................................ 14
4 - English
Introduction
ank you
We appreciate your choice of the Bose® SoundLink® around-ear wireless
headphones II. These wireless stereo headphones combine the audio performance
and comfort you expect from Bose with the freedom of wireless.
Unpacking
Check the carton for: headphones, carry case, USB charging cable, and back-up
audio cable. Be sure to save all packing materials. They provide the safest means
for any necessary shipping or transporting.
If any part of the product appears to be damaged, do not attempt to use it.
Contact your authorized Bose dealer immediately or call Bose Customer Service.
For contact information, see “Customer service” on page 14.
Bose® SoundLink® around-ear
wireless headphones II
USB charging cable
Carry case
Back-up audio cable
English - 5
Introduction
Headphone components
A
G
B
C
A
Back-up audio cable connector
B
USB charging connector
Headphone controls
C
D
Microphone
TM
E
D
Near Field Communication
E
(NFC) touchpoint
Power/Bluetooth® button
F
(three-position)
Bluetooth and battery
G
indicators
F
6 - English
Operation
Charging the battery
1. Plug the small end of the USB cable into the micro-USB connector on the right
earcup.
2. Plug the other end into a USB wall charger or computer that is powered on.
Allow up to three hours to fully charge the battery. A full charge will power the
headphones for up to 15 hours.
A 15-minute partial charge will power the headphones for 2 hours.
Note: The headphones will not play while charging.
Battery indicator
The battery indicator is located on the right earcup. While the battery is
charging, the battery indicator glows amber. When the battery is fully charged, the
indicator glows green.
Note: While the headphone are in use, the battery indicator will blink red when the
battery needs charging. See “Headphone status indicators” on page 11.
Selecting a language for voice prompts
The headphones feature voice prompts to guide you through the pairing and
connecting processes. The voice prompts also indicate the battery charge level
and the name of the currently connected device.
When you turn on the headphones for the first time, the voice prompts will be
heard in English. To select a different language:
1. Turn on the headphones and put them on your head.
2. Press and hold and at the same time until you hear the voice prompt
for the first language option.
English - 7
Operation
3. Press or to move through the list of language options:
English, Spanish, French, German, Mandarin, Japanese, Italian,
Portuguese, Dutch, Russian, Polish
4. When you hear your language, press and hold to select.
Turning voice prompts off/on
If you prefer not to hear voice prompts, press and hold and at the same time
until you hear, “Voice prompts off”.
Repeat to turn voice prompts back on.
Pairing a mobile device
1. Slide the Power/Bluetooth® button all the way up to the symbol and hold
until you hear, “Ready to pair” or you see the Bluetooth indicator blinking blue.
2. On your mobile device, make sure the Bluetooth feature is on.
(The Bluetooth menu is usually found in the Settings menu.)
3. Select Bose AE2 SoundLink from the device list.
You will hear, “Connected to <device name>” or you will see the Bluetooth
indicator glow solid white.
Note: Refer to your mobile device owner’s guide to learn more about how it
pairs/connects with other devices.
4. Repeat these steps to pair another device.
8 - English
Operation
Pairing with NFC
If your device supports Near Field Communication (NFC), you can easily pair it with
the headphones.
1. Turn the headphones power on.
2. Tap the NFC touchpoint on your mobile device to the center of the right
earcup. Your device may ask you to accept pairing.
Note: Before tapping your mobile device, make sure your device is unlocked
and the Bluetooth® and NFC features are both on. Refer to your mobile
device user’s guide to learn more about these features.
When the headphones are successfully connected, you will hear, “Connected
to <device name>” or you will see the Bluetooth indicator glow solid white.
3. Repeat these steps to pair another device.
Playing music
Once your mobile device is connected, open a music app and start audio on your
mobile device. You can play, pause, skip forward, skip backward, and adjust the
volume using either the headphone controls or the device controls.
See “Headphone controls” on page 10.
Using the headphones with multiple devices
The headphones can remember up to eight paired devices and can be actively
connected to two devices at a time.
When two devices are actively connected, you can play music from either device.
To switch between connected devices, pause audio on the first device and play
audio on the second.
English - 9
Operation
Disconnecting a Bluetooth® device
• Turn off the Bluetooth® feature on your device.
• If your mobile device supports NFC, tap the NFC touchpoint on your mobile
device to the center of the right earcup. Tap again to reconnect.
Reconnecting a previously connected device
When powered on, the headphones will automatically try to reconnect with the two
most recently connected devices. Make sure the device(s) are within range and
powered on.
Scrolling through other paired devices
To play music from a device in the headphone memory that is not currently
connected:
1. Slide all the way up to the symbol and release to hear which device(s)
are currently connected.
2. Within two seconds, slide all the way up to the symbol and release again
to connect to the next paired device.
3. Repeat step 2 until you hear the correct device name.
Note: To use this feature, voice prompts must be on. (See “Turning voice
prompts off/on” on page 8.)
Note: If a device is not within Bluetooth range (33 ft. or 10 m), scroll to the
next device.
Clearing the headphone memory
To clear the headphone memory of all devices:
1. Slide all the way up to the symbol and hold for ten seconds, until you
hear “Bluetooth device list cleared.”
2. Delete Bose AE2 SoundLink from the Bluetooth list on your mobile device.
All Bluetooth devices are cleared and the headphones are ready to pair.
Headphone controls
The headphone controls are located on the side of the right earcup.
Volume
up
Multi-function
button
Volume
down
10 - English
• Press once to play/pause or answer/end a call.
• Double press to skip forward.
• Triple press to skip backward.
• Press and hold to ignore an incoming call.
Operation
Headphone status indicators
The battery and Bluetooth® indicators are located on the side of the right earcup.
Green: Medium to full charge
Amber: Low charge
Red blinking: Need to charge
Blue blinking: Ready to pair
White blinking: Connecting
White solid: Connected
Battery charge level
Each time you power on the headphones, the voice prompt will announce the
headphone battery charge level.
If you are connected to an iOS device, the device will display the headphone
battery charge level near the upper right corner of the screen.
Using the back-up audio cable
Use the supplied back-up audio cable to connect a non-wireless device, or if the
headphone battery is depleted.
To use the audio cable:
1. Plug the audio cable into the connector on the left earcup.
2. Plug the audio cable into the connector on the device.
Note: Make sure is in the off position when using the back-up audio cable.
English - 11
Operation
Troubleshooting
Problem
Headphones do not
turn on
Headphones do not
connect with
mobile device
Headphones do not
connect with NFCenabled device
No sound
Poor sound quality
No audio from a
device connected
by audio cable
Poor sound quality
from a device
connected by audio
cable
What to do
• Make sure is in the on position.
• Charge the battery.
• On your mobile device, turn off the Bluetooth® feature and turn it
back on. Then try pairing again.
• Delete Bose AE2 SoundLink from the Bluetooth list on your mobile device. Then try pairing again.
• Move the mobile device closer to the headphones and away from
any interference or obstructions.
• Try pairing another mobile device.
• Visit owners.Bose.com/SoundLinkAE2 to see how-to videos
(US and Canada only).
• Clear the headphone memory: Slide all the way up to the
symbol and hold for ten seconds. Delete Bose AE2 SoundLink
from the Bluetooth list on your mobile device. Then try pairing
again.
• Make sure your mobile device supports NFC.
• Make sure your device is unlocked and the Bluetooth and NFC
features are both on.
• Make sure you are tapping the NFC touchpoint on the back of
your mobile device to the center of the right earcup.
• Make sure the headphone power is on and battery is charged.
• Make sure the volume is turned up on the headphones and on your
mobile device (or music app).
• Slide up and release to hear the name of the currently
connected device.
• Try a different music app.
• Try pairing another mobile device.
• If two mobile devices are actively connected, make sure the other
device has been paused first.
• If two mobile devices are actively connected, make sure both
devices are within range of the headphones (30 ft. or 10 m).
• Move the mobile device closer to the headphones, and away from
any interference.
• Try pairing another mobile device.
• Make sure the connected device is on and playing.
• Make sure the 3.5 mm plug is fully inserted into the headphones
connector, and fully inserted into the audio source.
• Make sure is in the off position.
• Make sure the volume is turned up on the headphones and on your
mobile device (or music app).
• Try connecting another device.
• Make sure the 3.5 mm plug is fully inserted into the headphones
connector, and fully inserted into the audio source.
• Try connecting another device.
12 - English
Care and Maintenance
Battery care
• Be sure to turn off the headphones when not in use.
• Before storing the headphones for more than a few months, be sure the battery
is fully charged.
• If the battery indicator begins to blink red while in use, the battery is low and you
must charge the headphones now.
Storage
The earcups rotate for easy, convenient storage. Place the headphones flat into the
case with the soft divider between the two earcups.
Cleaning
The headphones do not require scheduled cleaning. Should cleaning be necessary,
simply wipe the outside surfaces with a soft, dry cloth. Do not allow moisture to get
inside the earcups or the audio input connector. Do not use liquids or sprays.
Replacement parts and accessories
Replacement parts and accessories can be ordered through Bose Customer
Service. See “Customer service” on page 14.
English - 13
Care and Maintenance
Customer service
For questions about your headphones, contact your local Bose dealer.
• To contact Bose directly, visit: global.Bose.com
• US only: owners.Bose.com/SoundLinkAE2
Limited Warranty
Your Bose® SoundLink® around-ear wireless headphones II are covered by a limited
warranty. Details of the limited warranty are provided on the product registration
card that is included in the carton. Please refer to the card for instructions on how
to register. Failure to register will not affect your limited warranty rights.
The warranty information provided with this product does not apply in Australia
and New Zealand. See our website at www.bose.com.au/warranty or
www.bose.co.nz/warranty for details of the Australia and New Zealand warranty.
Technical information
Battery: Rechargeable, non-replaceable lithium-ion polymer
Charging time: 3 hours for full charge
Operating time: Up to 15 hours
Operating range: Up to 33 feet (10 m) from device
14 - English
©2015 Bose Corporation, The Mountain,
Framingham, MA 01701-9168 USA
AM748270 Rev. 00
Loading...