Bosch W-STRC, W-STWC Specsheet
Fire Alarm Systems | W‑STxC Ceiling‑mount Multi‑candela Strobes
W‑STxC Ceiling‑mount Multi‑candela
Strobes
www.boschsecurity.com
u Sleek modern aesthetics
u Multiple voltages (12 VDC or 24 VDC)
The Cooper Wheelock Exceder Series Strobes feature
a sleek modern design that incorporates high reliability
and high-efficiency optics to minimize current draw.
The reduced current draw allows for a greater number
of devices on the two‑wire notification appliance
circuit. This, in combination with eight candela options
in one appliance, no tools needed for changing
settings, voltage test points, 12 V or 24 V DC
operation, the universal mounting base, and multiple
mounting options results in a reduced cost of
ownership.
These strobes provide eight candela settings. All the
switches to change these settings can be set without a
tool and are located behind the appliance to prevent
tampering.
The separate universal mounting base can be easily
mounted to five industry‑standard back box types.
They can also be pre‑wired to allow full testing of the
circuit wiring before the appliance is installed and the
surface finished. These wall‑mounting strobes also
feature voltage test points for taking readings with a
volt meter for troubleshooting or AHJ inspection.
u Voltage test points
u Eight strobe candela options
u Universal mounting base
Certifications and approvals
Cooper Wheelock holds these Listings and Approvals:
Region Certification
USA UL UUKC: Signaling Appliances and Equip-
ment for the Hearing Impaired (ANSI/UL
1971), UVAV: Visual-signal Appliances
for Fire-protective Signaling Systems
(ANSI/UL 1638)
CSFM see our website
Installation/configuration notes
Compatibility
Strobe:
These strobes provide a non-synchronized strobe
appliance when connected directly to a Fire Alarm
Control Panel (FACP), or provide a synchronized
strobe appliance when used in conjunction with an
FACP that incorporates the Cooper Notification sync
protocol, a Cooper Notification Sync Module, or the
Cooper Notification Power Supply. They are designed
to flash at 1 flash per second minimum over their
Regulated Voltage Range.
| W‑STxC Ceiling‑mount Multi‑candela Strobes
2
Notice
Strobes are not designed to be used on coded
systems in which the applied voltage is cycled on
and off.
Compatible Products
The following Bosch Security Systems, Inc. products
are compatible with the Cooper Wheelock Exceder
Series Strobes:
Category Product ID Product Description
Control Panels FPA-1000
1
Analog Addressable Fire
Panels
FPD-7024
1
Conventional or
Addressable2 FACP
D10024A
D8024
D9124
D7024
3
3
3
3
Analog FACP
Analog FACP
Addressable FACP
Conventional or
Addressable2 FACP
D7022
3
Conventional FACP
Modules SM‑12/24‑R Synchronization module
(red)
DSM‑12/24‑R Dual synchronization
module (red)
Power Supplies FPP-RNAC-8A-4C
1
Remote Notification
Appliance Circuit (RNAC)
Power Supply
PS‑24‑8MC
1
Power supply with built-in
synchronization protocol
1
These products have built‑in Cooper Notification
synch protocol.
2
When used with a D7039 Multiplex Expansion
Module, the FPD‑7024 and D7024 become
addressable FACPs.
3
For synchronization, use the SM or DSM modules
with these control panels.
Mounting Considerations
The Universal Mounting Base supplied with each
strobe can be pre-wired. With the supplied Contact
Cover in place, the pre‑wired circuit can be checked
for continuity before the strobes are mounted. The
strobes snap onto the pre-installed Universal Mounting
Bases with the Contact Covers removed and can be
secured to the base with an optional securing screw.
The Universal Mounting Base flush mounts on singlegang, double-gang, 4 in. square, 4 in. octal, 3.5 in.
octal and 100 mm European-type back boxes.
Wiring Considerations
The wiring terminals on the Universal Mounting Base
accept two appliance wires with diameters between
12 AWG and 18 AWG (ISO 4 mm2 and 0.75 mm2) at
each terminal.
Parts included
Quant. Component
1 Strobe appliance
1 Universal mounting base
1 Contact cover
1 Hardware pack
• Two pan head mounting screws
• One securing screw
1 Literature – Installation Instructions
Technical specifications
Electrical
Strobe Current Draw
24 V nominal (16.0 V to 33.0 V range)
Voltage Type Current Draw
DC: 15 cd: 61 mA, 30 cd: 85 mA, 60 cd: 103 mA,
75 cd: 135 mA, 95 cd: 163 mA,
115 cd: 182 mA, 150 cd: 205 mA,
177 cd: 253 mA
FWR: 15 cd: 83 mA, 30 cd: 105 mA,
60 cd: 166 mA, 75 cd: 185 mA,
95 cd: 223 mA, 115 cd: 256 mA,
150 cd: 328 mA, 177 cd: 372 mA
12 V nominal (8.0 V to 17.5 V range)
Voltage Type Current Draw
DC: 15 cd: 110mA
Voltage (input)
Regulated Range
12 VDC 8.0 V to 17.5 V
24 VDC or Vrms 16.0 V to 33.0 V
Environmental
Environment: Indoor, dry
Relative Humidity: 93±2% maximum, non‑condensing
Temperature
+32°F to +120°F (0°C to +49°C)
(operating):
Mechanical
Candela Ratings1: 15 cd, 30 cd, 60 cd, 75 cd, 95 cd, 115 cd,
150 cd, or 177 cd
Dimensions: 6.68 in. diameter x 2.63 in. depth
(170 mm diameter x 67 mm depth)
Material: Molded plastic enclosure incorporating a
Xenon flashtube and Lexan lens.
1
When set for 12 V operation, strobe devices are only
approved by UL to be set at 15 cd and only to be
powered by DC not FWR.
Loading...