Bosch VTN-4075-V321 User Manual

AN bullet 4000

960H Day/Night Bullet Camera

2 en | Table of Contents 960H Day/Night Bullet Camera

Table of Contents

1 Cautions

2 Important safety instruction

3 Features

4 Components

5 Camera parts

6 Installation

6.1 Mounting position

6.2 Monitor connection

6.3 Camera adjustment

7 OSD menu structure

8 Specication

8.1 Dimensions

Bosch Security Systems User Manual 2012.11

960H Day/Night Bullet Camera Cautions | en 3

1 Cautions

This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions;

1. This device may not cause harmful interference.

2. This device must accept any interference received,
including interference that may cause undesired operation.

Note!

This equipment has been tested and found to comply with the limits
for a Class A digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with
the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area
is likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.”

WARNING

This is a class A product. In a domestic environment this product may
cause radio interference in which case the user may be required to
take adequate measures.

CAUTION!

Any changes or modications in construction of this devies which are

not expressly approved by the party responsible for compliance could
void the user’s authority to operate the equipment.

CAUTION!

1. A regulated DC12V 300mA power supply is recommended for use with
this camera for the best picture and the most stable operation.
An unregulated power supply can cause damage to the camera.
When unregulated power supply is applied, product warranty will be
out of subject.

2. It is recommended that the camera is used with a monitor that has a
CCTV quality 75 video impedance level. If your monitor is switched to
high impedance then please adjust accordingly.

3. Do not attempt to disassemble the camera to gain access to the
internal components. Refer servicing to your dealer.

4. Never face the camera towards the sun or any bright or reective light,

which may cause smear on the picture and possible damage to the CCD.

5. Do not remove the serial sticker for the warranty service.

6. Do not expose the camera to rain or other types of liquid.

7. The apparatus must be connected to a mains socket-outlet with a
protective earthing connection.

Bosch Security Systems User Manual 2012.11

4 en | Cautions 960H Day/Night Bullet Camera

Correct Disposal of This Product
(Waste Electrical & Electronic Equipment)

(Applicable in the European Union and other European countries with
separate collection systems)

This marking shown on the product or its literature, indicate that
it should not be disposed with other household wastes at the end
of its working life. To prevent possible harm to the environment or
human health from uncontrolled waste disposal, please separate this
from other types of wastes and recycle it responsibly to promote the
sustainable reuse of material resources.
This product should not be mixed with other commercial wastes

purchased this product, or their local government ofce, for details of

where and how they can take item for environmentally safe recycling.
Business users should contact their supplier and check the terms and
conditions of the purchase contract.
Household users should contact either the retailer where they for
disposal.

CAUTION

RISK OF ELECTRIC SHOCK DO NOT OPEN

CAUTION:

TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER(OR BACK). NO USER. SERVICING
TO QUALIFED SERVICE PERSONNEL.

This symbol is intended to alert the user to the presence of
uninsulated “dangerous voltage” within the product’s enclosure

that may be of sufcient mangnitude to constitute a risk of

electric shock to persons.

This symbol is intended to alert the user to the presence of
important operating and maintenance(servicing) instruction in
the literature accompanying the appliance.

CAUTION!

These servicing instructions are for use by qualied service personnel

only. To reduce the risk of electric shock do not perform any servicing
other than that contained in the operating instructions unless you are

qualied to do so.

Use Class 2 Power Supply Only

Bosch Security Systems User Manual 2012.11

960H Day/Night Bullet Camera Important safety instructions | en 5

2 Important safety instructions

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings. Install in accordance with
the manufacturer’s instructions.

8. Do not install near any heat sources such as radiators, heat

registers, stoves, or other apparatus (including ampliers) that

produce heat.

9. Do not defeat the safety purpose of the polarized or grounding­type plug. A polarized plug has two blades with one wider than
the other. A grounding type plug has two blades and a third
grounding prong. The wide blade or the third prong are provided

for your safety. If the provided plug does not t into your outlet,

consult an electrician for replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched
particularly at plugs, convenience receptacles, and the point
where they exit from the apparatus.

11. Only use attachments/accessories specied by the manufacturer.

12. Use only with the cart, stand, tripod, bracket, or table specied
by the manufacturer, or sold with the apparatus. When a cart is
used, use caution when moving the cart/apparatus combination
to avoid injury from tip-over.

13. Unplug this apparatus during lightning storms or when unused for
long periods of time.

14. Refer all servicing to qualied service personnel. Servicing is
required when the apparatus has been damaged in any way, such
as power-supply cord or plug is damaged, liquid has been spilled
or objects have fallen into the apparatus, the apparatus has been
exposed to rain or moisture, does not operate normally, or has
been dropped.

Bosch Security Systems User Manual 2012.11

6 en | Features/Components 960H Day/Night Bullet Camera

3

Features

The camera has the following features:

•

Ultra high resolution, 960H (1/3") Sensor

•

2.8-12mm lens with True Day/Night lter for optimum performance

in various lighting conditions.

•

720 TV Lines Horizontal Sensor Resolution.

•

Multi language On Screen Display (OSD) with joystick control.

•

2DNR.

•

4 Privacy Zones.

•

Motion Detection.

•

ATR(Adaptive Tone-curve Reproduction / Digital WDR)

•

Cable managed bracket for secure and clean installation.

•

Vandal resistant. (IK08)

•

Outdoor rated. (IP66)

4 Components

Qty Description

VTN-4075-V3x1(C)

1

camera with integrated
mounting bracket

Video Output

1

Test Cable

Screws

3

(PH/1(SUS) 5x30)

Wrench

1

(M6 hex)

1 Guide Pattern

User Manual

1

(this booklet)

Bosch Security Systems User Manual 2012.11

960H Day/Night Bullet Camera Camera parts | en 7

5 Camera parts

1
2
3
4
5
6
7

OSD joystick

Sunshield Fixing Bolt
Sunshield
Mounting Bracket
Housing Body
Housing Front
Photo cell
Lens

➋ ➌

➊

➍➎➏ ➐

NEAR

FAR

TELE

WIDE

Rubber seal

Service cable connector

Bosch Security Systems User Manual 2012.11

8 en | Installation 960H Day/Night Bullet Camera

6 Installation

6.1 Mounting position

To prevent injury, this apparatus must be securely attached to

the oor/wall in accordance with the installation instructions.

The image sensors in modern cameras are highly sensitive and require

NOTICE!

special care for proper performance and extended lifetime. Follow the
guidelines for optimum results with your camera:
– Do not expose to direct sunlight or bright spotlights in operating and
nonoperating conditions.

– Avoid bright lights in the eld of view of the camera. Bright lights cause

a “smearing” effect, which is visible as white lines above and below the
highlight. Prolonged exposure to bright lights may cause bleaching of the

sensor's color lters. This will be visible as colored spots in the picture

and is irreversible.

WARNING!

WARNING!

CAUTION!

The mounting surface, mounting screws/plugs, and junction box must be
stable and capable of supporting a maximum load of 4 kg (8.82 pounds).
Mounting to an improper surface or using improper mounting material can
cause camera malfunction and is a potential safety hazard.

Make sure that appropriate mounting screws and anchors are used for the
surface to which the camera is mounted. The supplied universal mounting

screws can be used with most plastic anchors, please conrm compatibility

before mounting the camera.
To prevent humidity problems, the camera must be installed in dry

conditions, and the cable leads should be sealed after they are connected.

360°

* 1st Axis

360°

* 3rd Axis

Bosch Security Systems User Manual 2012.11

90°

* 2nd Axis

960H Day/Night Bullet Camera Installation | en 9

6 Installation

6.2 Monitor connection

Female
BNC connector

Terminal block

Screw
Terminal

2.6x3.2



(0.1x0.12)

Terminal block connector

10.16
(0.4)

5.08(0.2)

15.4(0.6)

6.3 Camera adjustment

To prevent humidity problems, the camera must be installed in dry conditions.

CAUTION!

The housing front should never be removed in wet or moist conditions. Doing
so could cause condensation on the inside of the camera window.

1.

Remove the housing front.

2.

Connect service monitor. (optional)

3.

Adjust zoom and focus.

4.

Fasten the zoom and focus lever.

5.

Adjust OSD settings. (refer to OSD section)

6.

Disconnect service monitor cable. (optional)

7.

Re-mount housing front. Include warning to (1) check rubber seal is in place. And (2) tighten

housing front rmly to ensure protection against water ingress.

V

"+","-" Indication

18.2(0.71)

Camera

mm
(in.)

DUAL

(DC12V/AC24V)

DUAL(DC12V/AC24V)

Regulated Power Supply

X

Ground contact

Signal contact

TV Monitor

Video In

*Sold separately

Housing front fastened enough.
(No gap between housing front and housing body)
Protection against water ingress ensured.

Housing front not fastened enough.
(Gap between housing front and housing body)
Risk of water ingress.

Bosch Security Systems User Manual 2012.11

10 en | OSD menu structure 960H Day/Night Bullet Camera

7 OSD menu structure

MAIN MENU 1st Sub 2nd Sub 3rd Sub 4th Sub

LENS

SHUTTER /
AGC

* SHUT+IRIS: Both the Shutter and the Mechanical Iris are automatically
adjusted according to brightness.
* Auto Iirs(Default): The Shutter stays at the manually selected value
and only the Mechanical Iris adjusts brightness.

MAIN MENU 1st Sub 2nd Sub 3rd Sub 4th Sub

WHITE BAL

BACK LIGHT OFF,BLC,HLC

Bosch Security Systems User Manual 2012.11

MANUAL

TYPE DC
MODE

AUTO

SPEED (000 ~ 255)
RETURN

HIGH LUMINANCE

AUTO

LOW LUMINANCE

RETURN
MODE SHUT+AGC

SHUTTER

MANUAL

AGC 6, 12, 18, 24, 30, 36, 42, 44.8
RETURN

SPEED (000 ~ 255)

AT W

PUSH

USER1

USER2

ANTI CR

MANUAL

PUSH LOCK

DELAY CNT (000 ~ 255)
ATW FRAME x0.50,x1.00,x1.50,x2.00
ENVIRONMENT INDOOR,OUTDOOR
RETURN

B-GAIN (000 ~ 255)
R-GAIN (000 ~ 255)
RETURN
B-GAIN (000 ~ 255)
R-GAIN (000 ~ 255)
RETURN

LEVEL
RETURN

AUTO, OPEN,
CLOSE

MODE
BRIGHTNESS (000 ~ 255)

MODE AGC,OFF
BRIGHTNESS

1/50(PAL),1/120(PAL)
1/60(NTSC),1/100(NTSC)
1/250,1/500,1/1000,1/2000
1/4000,1/10000

NTSC:(30 ~ 115)
PAL:(28 ~ 134)

SHUT, AUTO IRIS
SHUT+AUTO IRIS,

x0.25, x0.50, x0.75,
x1.00

960H Day/Night Bullet Camera OSD menu structure | en 11

7 OSD menu structure

MAIN MENU 1st Sub 2nd Sub 3rd Sub 4th Sub

PIC ADJUST

ATR

* ATR (Adaptive Tone-Curve Reproduction)

The function provides gradation compensation to improve the contrast of
subjects both low luminace areas and high luminance areas.

MAIN MENU 1st Sub 2nd Sub 3rd Sub 4th Sub

MOTION
DET

NEXT
EXIT
SAVE ALL

MIRROR OFF,ON
BRIGHTNESS (000 ~ 255)
CONTRAST (000 ~ 255)
SHARPNESS (000 ~ 255)
HUE (000 ~ 255)
GAIN (000 ~ 255)
RETURN

OFF

ON

ON

OFF

LUMINANCE LOW,MID,HIGH

CONTRAST

RETURN

DETECT SENS (000 ~ 127)

BLOCK DISP

MONITOR AREA ON,OFF

AREA SEL

RETURN

LOW,MIDLOW,MID,
MIDHIGH,HIGH

OFF, ON, ENABLE
(CONTROLER)

1/4, 2/4, 3/4, 4/4

TOP

BOTTOM

LEFT

RIGHT

NTSC:000 ~ 244
PAL: 000 ~ 288

NTSC:(000 ~ 244)
PAL:(000 ~ 288)

NTSC:(000 ~ 474)
PAL:(000 ~ 468)

NTSC:(000 ~ 474)
PAL:(000 ~ 468)

Bosch Security Systems User Manual 2012.11

12 en | OSD menu structure 960H Day/Night Bullet Camera

7 OSD menu structure

MAIN MENU 1st Sub 2nd Sub 3rd Sub 4th Sub

AREA SEL

PRIVACY

DAY/NIGHT

NR

CAMERA ID

LANGUAGE

CAMERA RESET
BACK
EXIT

SAVE ALL

* Important Note:

- Any changes made to the camera settings must be saved prior to exiting the
OSD menu. Otherwise all changes will be discarded.

- By changing the lens option in the OSD from MANUAL to AUTO will
automatically change the SHUTTER/AGC setting from AUTO IRIS to
SHUT+AUTO IRIS.(Default:AUTO IRIS)

Bosch Security Systems User Manual 2012.11

ON

COLOR 1 ~ 8
TRANSP 0.00, 0.50, 0.75, 1.00
MOSAIC OFF,ON

OFF

AUTO

COLOR

BW
EXT1

EXT2

NR MODE OFF, Y, C, Y/C
Y LEVEL (000 ~ 015)
C LEVEL (000 ~ 015)
RETURN

OFF

ON

ENGLISH,
PORTUGUÊS, ESPAÑOL,

RETURN

BURST OFF,ON
DELAY CNT 0 ~ 255
DAY -> NIGHT 0 ~ 255
NIGHT -> DAY 0 ~ 255
RETURN

BURST OFF, ON
RETURN

EDIT MODE
RETURN

日本語

1/4, 2/4, 3/4, 4/4
TOP

BOTTOM

LEFT

RIGHT

, DEUTSCH, FRANCAIS, Русский

中文

NTSC:(000 ~ 244)
PAL:(000 ~ 288)

NTSC:(000 ~ 244)
PAL:(000 ~ 288)

NTSC:(000 ~ 474)
PAL:(000 ~ 468)

NTSC:(000 ~ 474)
PAL:(000 ~ 468)

960H Day/Night Bullet Camera Specication | en 13

8 Specication

Model
Image Device
Scanning System
Scanning Frequency
H. Sensor Res.
Actual H. Res.
Total Pixels
Effective Pixels
S/N Ratio
Min. Illumination
Sync. System
Gamma
Video Output

Lens
Lens focal length
Aperture
Lens adjustment
Electronic Shutter
BLC
White Balance

2DNR
ATR
Function

Motion Detection
Privacy Masking
Language

Day & Night
OSD
OSD Control
IP Rating
Operating Temperature
Storage Temperature
Power Consumption

Cable
Management Bracket
Video interface
Weight

Housing material Casted/machined Aluminium
Paint color Camera / bracket: Black RAL9017

Vandal resistant Yes (IK08)

Bosch Security Systems User Manual 2012.11

Outdoor rated Yes (IP66)

VTN-4075-V321(NTSC) VTN-4075-V311(PAL)
Ultra high resolution, 960H (1/3") Sensor
2 : 1 Interlace

15.734 KHz(H),59.94 Hz(V) 15.625 KHz(H), 50 Hz(V)
720TVL
650TVL
1020(H)x508(V) 1020(H)x596(V)
976(H)x494(V) 976(H)x582(V)
More than 50dB (AGC Off)
COLOR (0.05 Lux), BW (0.02Lux)
Internal
r = 0.45

1.0 Vp-p Composite (75Ω)

Varifocal Auto IRIS & DN Lens Built-in

2.8-12mm
F1.4~360
Internal
1/60 sec 1/50 sec
OFF / BLC / HLC

ATW / PUSH / USER1 / USER2 /
ANTI CR / MANUAL / PUSH-LOCK

On / Off (Level Adjustable)
On / Off (Level Adjustable)
MIRROR / BRIGHTNESS / CONTRAST /

SHARPNESS / HUE / GAIN

Zone 4ea
Zone 4ea
English, Japanese, German, French, Russian,

Portuguese, Spanish, Simplied Chinese

True Day & Night with ICR Mechanism
Built-in
Internal
IP66 (Water resistant)

-30˚C to +50˚C (-22˚F to + 122˚F)

-20˚C to +60˚C (-4˚F to + 140˚F)

Dual : DC12V(±10%), Max. 190 mA /
AC24V(±10%), Max. 2.9 W

Yes

1 standard BNC connector for analog output
Approx. 960g (including bracket)

Sunshield: Silver grey RAL9006

14 en | Dimensions 960H Day/Night Bullet Camera

8-1 Dimensions

Ø70(2.75)

148(5.82)

(2.36)

60

120(4.72)

Approx. 257(10.1)

(2EA)

126(4.96)

Ø80(3.14)

3-Ø6.0(0.23)

mm

(in.)

Bosch Security Systems User Manual 2012.11

Bosch Security Systems User Manual 2012.11

16 简体中文版|目录 室外日/夜子弹型摄像机

目录

1 注意事项

2 重要安全指示

3 特性

4 组件

5 摄像机零件

6 安装

6.1 装配位置

6.2 连接监视器

6.3 摄像机调整

7 屏幕显示选单结构

8 规格

8.1 尺寸

博世安防系统 使用手册 2012.11

室外日/夜子弹型摄像机 注意事项|简体中文版 17

1 注意事项

此装置符合FCC条例第15部分的规定。
操作需符合以下两种条件；

1. 此装置不会引起有害的干扰。

2. 此装置必须能够承受任何收到的干扰，包括可能引起意外操作的干扰。

注记!
根据FCC条例第15部分之规定，此装备经证实符合A类数字装置的限制规定。
这些限制的目的是为了在商业环境中操作本装备时，可提供适当防护，以
防止有害的干扰。本装备会产生、使用且能发射射频能量，若未依据操作
指南安装时，可能会对无线电通信产生有害干扰。在住宅区操作本装备时
可能造成有害干扰，此时，用户需自费矫正此干扰。

警告
此为A类产品。在家用环境下，此产品可能引发无线电干扰，在此情况
下，用户需采取适当措施。

注意!
装备的结构未经负责合规性的相关方明确许可的变更或修改，都可能致
使用户失去操作本装备的权利。

注意!

1. 为了获得最佳图像且保持稳定操作，此摄像机建议采用稳压的12V 300mA直流电源。
非稳压的供应电源可能造成摄像机受损。
采用非稳压电源供应时，产品将不在保固范围内。

2.建议应将此摄像机，与拥有CCTV品质75视频阻抗等级的监视器一起使用。
当监视器切换为高阻抗时，请相应调整。

3.请勿尝试拆解摄像机以接近内部组件。保修请洽询您的经销商。

4.请勿将摄像机直接朝向日光或任何强光或反射光线，以免图像模糊且可能致
使CCD(电荷耦合组件)受损。

5.请勿拆除保固服务的序号标签。

6.请勿让摄像机曝露在雨水或其它类型的液体中。

7.此装置必需连接到具有保护接地的主电源插座。

博世安防系统 使用手册 2012.11

18 简体中文版|注意事项 室外日/夜子弹型摄像机

正确弃置本产品
(废弃电器与电子设备)

(适用于欧盟及其它拥有分类回收制度的欧洲国家)

产品或其文件上显示此记号时，表示当其使用寿命结束时，不应以其它
家庭废弃物方式处理。
为避免由于未受控制的废弃物处理方式，对环境或人类健康产生可能的
伤害，请与其它类型废弃物分开并回收，让材料资源可持续再利用。
本产品不可与其它商业垃圾混合，有关环保回收项目的地点与方法的详
细信息，请向购买处所或您当地的政府办事处洽询。
企业用户应与其供货商联系，并确认其购买合同条款与条件。
家庭用户应向零售商洽询其处置方式。

注 意

触电危险请勿开启

注意: 为了降低触电风险，用户请勿拆除外盖(或背盖)。请交由合格的

服务人员进行保修。

为了降低触电风险，用户请勿拆除外盖(或背盖)。请交由合格的
服务人员进行保修。

此符号是在提醒使用者，随附于装置的文件中，有重要的操作与
保养(服务)指南。

注意!

这些保修指南，仅供合格的服务人员使用。为了降低触电风险，除非您
具备资格，否则请勿执行任何操作指南所述以外的保修。
仅能采用等级2的电源供应

博世安防系统 使用手册 2012.11

室外日/夜子弹型摄像机 重要安全指示|简体中文版 19

2 重要安全指示

1. 详读这些指示。

2. 保存这些指示。

3. 注意所有警告事项。

4. 遵照所有指示。

5. 切勿在靠近水的地方使用本装置。

6. 只能以干布进行清洁。

7. 请勿妨碍所有通风口。依据制造商指南进行安装。

8. 请勿安装在像是散热器、通风温度调节设备、火炉或其它会产生热

量设备(含放大器)的任何热源附近。

9. 请勿破坏有安全作用的极化或接地型插头。极化插头有两个金属
片，其中一片比另一片为宽。接地型插头则有两个插片和第三支用
来接地的插脚。宽的金属片或第三支插脚，都是为了您的安全。若
所提供的插头不适用于您的插座时，请洽询合格电工更换老式插
座。

10. 保护电源线免被踩踏或挤压，特别是靠近插头、便捷插座及离开该
装置的地方。

11. 仅能采用制造商所指定的附件或配件。

12. 仅能采用制造商所指定或随设备出售的推车、支架、三脚架、托架

或桌子。使用推车时，移动推车/设备的组合时要特别小心，以免
翻倒受伤。

13. 闪电暴风雨或是长期未使用，请将装置插头拔除。

14. 所有保修应交由合格的服务人员来进行。当设备已因任何方式损坏

时，都需要维修(如电源线或插头损坏、 液体溅入或有异物掉入设
备中、设备曾曝露于雨中或潮湿环境中、操作不正常或曾被摔落
等)。

博世安防系统 使用手册 2012.11

20 简体中文版|特性/组件 室外日/夜子弹型摄像机

3 特性

此摄像机有以下特性

•

超高分辨率，960H(1/3”)感应器。

•

拥有真实日/夜滤镜，可提供各种照明条件下最佳性能的8-12mm镜头。

•

720电视线的水平感应器分辨率。

•

附摇杆控制的多国语言屏幕显示(OSD)。

•

2DNR。

•

4个隐私区域。

•

动域检测。

•

ATR(自适应色阶再现/数字WDR)

•

电缆管理托架，以利安全与整齐的装设。

•

防破坏。(IK08)

•

室外级。(IP66)

4 组件

数量 说明

VTN-4075-V3x1(C)

1

含整合式装配托架的摄像机

视频输出

1

测试缆线

螺丝

3

(PH/1(SUS) 5x30)

扳手

1

(M6六角)

1 导引样式板

使用手册

1

(本手册)

博世安防系统 使用手册 2012.11

室外日/夜子弹型摄像机 摄像机零件|简体中文版 21

5 摄像机零件

OSD摇杆

1

遮阳罩固定螺栓

2

遮阳罩

3

装配托架

4

外罩本体

5

外罩前端

6

光敏电阻

7

镜头

➋ ➌

➊

➍➎➏ ➐

近

远

望远

宽

橡胶密封垫

保修缆线接头

博世安防系统 使用手册 2012.11

22 简体中文版|安装 室外日/夜子弹型摄像机

6 安装

6.1 装配位置

为避免伤害，请依据安装指南，将装置紧密固定在地板/墙壁上。

这个新型摄像机里的图像感应器十分敏感，为确保其性能并延长寿命，必需特别注意。

注记!

请遵照指南，让您的摄像机获得最佳效果：
–不论操作或非操作状态下，都不要将它曝露在日光或聚光灯直射处。
–避免摄像机视野中有强光。强光将造成“拖影”，会在强光上方与下方形成白色线。
长期暴露在明亮的光线中，可能导致感应器彩色滤光片白化的情形。
这样会在图片中形成彩色斑点，且无法消除。

装配面、装配螺丝/插头及接线盒等均需稳固，且最高能支撑4公斤(8.82磅)的负荷。

警告!

装配在不适当的表面，或使用了不当的装配材料时，可能造成摄像机故障，且也潜在
安全危险。

确认装设摄像机表面采用适当的装配螺丝与膨胀管。随附的通用安装螺丝可供大多数

注意!

塑料膨胀管使用，请在安装摄像机前确认其兼容性。

为避免潮湿问题，摄像机应安装在干燥环境下，当完成连接后，应将电缆导线密封。

警告!

360°

* 第1个转轴

360°

* 第3个转轴

博世安防系统 使用手册 2012.11

90°

* 第2个转轴

室外日/夜子弹型摄像机 安装|简体中文版 23

6 安装

6.2 连接监视器

BNC母接头

端子台

螺丝端子

2.6x3.2



(0.1x0.12)

6.3 摄像机调整

注意!

1.

2.

3.

4.

5.

6.

7.

接地接点

信号接点

端子台连接器

摄像机

(DC12V/AC24V)

双电压

"+","-" 指示

10.16
(0.4)

5.08(0.2)

为避免潮湿问题，摄像机需安装在干燥环境下。绝对不可以在潮湿状况下
将前端外罩拆除，否则可能导致摄像机窗口内部凝结水气。

拆除前端外罩。
连接保修监视器(选购)。
调整缩放与对焦。
固定缩放与对焦控制杆。
调整屏幕显示的设定(请参照屏幕显示乙节)。
卸除保修屏幕缆线(选购)。
装回前端外罩。需特别注意(1)检查橡胶密封垫是否装妥，及(2)紧密锁紧前端外罩，
确保水气不会进入。

15.4(0.6)

18.2(0.71)

mm

双稳压(DC12V/AC24V)

(in.)

电源供应

电视监视器

Video In

*分开销售

V X

前端外罩充分锁紧。
(前端外罩与外罩本体之间无间隙)
可确保防止水气进入。

博世安防系统 使用手册 2012.11

前端外罩未充分锁紧。
(前端外罩与外罩本体之间有间隙)
有水气进入风险。

24 简体中文版|屏幕显示选单结构 室外日/夜子弹型摄像机

7 屏幕显示选单结构

主选单 第1层子选单 第2层子选单 第3层子选单 第4层子选单

镜头

快门 / 自动
增益控制

*快门+光圈：快门与机械光圈都会依据亮度自动调整。
*自动光圈(预设)：快门会维持在手动所选择的位置，且只使用光圈来调整亮度。

主选单 第1层子选单 第2层子选单 第3层子选单 第4层子选单

白平衡

逆光补偿 关、逆光补偿、高亮度补偿

手动

自动

自动

手动

自动跟踪白平
衡

推进推进

用户1

用户2

抑制色滚

手动

推进锁定

控制 DC
模式 自动、关闭、开放
速度 (000 ~ 255)
返回

高辉度

低辉度

返回
模式 快门+自动增益

快门

自动增益 6, 12, 18, 24, 30, 36, 42, 44.8
返回

速度 (000 ~ 255)
延迟控制 (000 ~ 255)
自动跟踪白平衡
框
环境设置 室内、室外
返回

B增益 (000 ~ 255)
R增益 (000 ~ 255)
返回
B增益 (000 ~ 255)
R增益 (000 ~ 255)
返回

等级

返回

模式

亮度 (000 ~ 255)

模式

亮度

1/50(PAL),1/120(PAL)
1/60(NTSC),1/100(NTSC)
1/250,1/500,1/1000,1/2000
1/4000,1/10000

x0.50,x1.00,x1.50,x2.00

NTSC:(30 ~ 115)
PAL:(28 ~ 134)

快门、自动光圈、
快门+自动光圈

自动增益控制、关
闭

x0.25, x0.50,
x0.75, x1.00

博世安防系统 使用手册 2012.11

室外日/夜子弹型摄像机 屏幕显示选单结构|简体中文版 25

7 屏幕显示选单结构

主选单 第1层子选单 第2层子选单 第3层子选单 第4层子选单

图像调整

自适应色阶
再现

* ATR (自适应色阶再现)
此功能提供了色调补偿，以提高存在同一个画面低亮度与高亮度等区域的主体
对比度。

主选单 第1层子选单 第2层子选单 第3层子选单 第4层子选单

动域检测

下一页
退出
全部储存

镜像 关、开
亮度 (000 ~ 255)
对比度 (000 ~ 255)
锐度 (000 ~ 255)
色调 (000 ~ 255)
增益 (000 ~ 255)
返回

关

开

开

关

辉度 低、中、高

对比度

返回

检测灵敏度 (000 ~ 127)

块状显示 关、开、开启(控制器)

监视区域 开、关

区域选择

返回

低、中等偏低、中、
中等偏高、高

1/4, 2/4, 3/4, 4/4

上

下

左

右

NTSC:000 ~ 244
PAL:000 ~ 288

NTSC:000 ~ 244
PAL:000 ~ 288

NTSC:000 ~ 474
PAL:000 ~ 468

NTSC:000 ~ 474
PAL:000 ~ 468

博世安防系统 使用手册 2012.11

26 简体中文版|屏幕显示选单结构 室外日/夜子弹型摄像机

7 屏幕显示选单结构

主选单 第1层子选单 第2层子选单 第3层子选单 第4层子选单

区域选择

隐私区域屏
蔽

日/夜模式

减噪

摄像机标示
码

语言 英语、日本语、德语、法语、俄语、葡萄牙语、西班牙语、中文

摄像机复位
上一页
退出

全部储存

开

彩色 1 ~ 8
透明度 0.00,0.50, 0.75, 1.00
马赛克 关、开

关

自动

彩色

黑白

外部1
外部2

减噪模式
Y等级 (000 ~ 015)

C等级 (000 ~ 015)
返回

关

ON

返回

脉冲 关、开
延迟控制 0 ~ 255
日->夜 0 ~ 255
夜->日 0 ~ 255
返回

脉冲 关、开
返回

关, Y, C,
Y/C

编辑模式
返回

* 重要注记：

- 在退出屏幕显示选单前，需先储存所有在摄像机设定上所做的变更。
否则所有变更都会无效。

- 将屏幕显示中之镜头选项从手动改为自动，可以自动将快门/自动增益控制设
定，从自动光圈变为快门+自动光圈(默认值为自动)。

1/4, 2/4, 3/4, 4/4

上

下

左

右

NTSC:(000 ~ 244)
PAL:(000 ~ 288)

NTSC:(000 ~ 244)
PAL:(000 ~ 288)

NTSC:(000 ~ 474)
PAL:(000 ~ 468)

NTSC:(000 ~ 474)
PAL:(000 ~ 468)

博世安防系统 使用手册 2012.11

室外日/夜子弹型摄像机 规格|简体中文版 27

8 规格

型式
图像装置
扫瞄系统
扫瞄频率
感应器水平分辨率
实际水平分辨率
总像素
有效像素
信杂(S/N)比
最低照度
同步系统
伽玛值
视频输出

镜头
镜头焦距
光圈
镜头调整
电子快门
逆光补偿
白平衡

2DNR
自适应色阶再现
功能

动域检测
隐私区域屏蔽
语言
日与夜
屏幕显示
屏幕显示控制
IP防护等级
操作温度
储存温度

电力消耗

缆线管理托架

视频接口
重量

外壳材料 铸造 / 机械加工铝质
油漆颜色 摄像机 / 托架：黑色RAL9017

防破坏 是(IK08)
室外等级 是(IP66)

VTN-4075-V321(NTSC) VTN-4075-V311(PAL)
超高分辨率，960H (1/3")感应器
2 : 1交错

15.734 KHz(H),59.94 Hz(V) 15.625 KHz(H), 50 Hz(V)
720TVL
650TVL
1020(水平) x 508(垂直) 1020(水平) x 596(垂直)
976(水平) x 494(垂直) 976(水平) x 582(垂直)
大于50dB(自动增益关闭)
彩色(0.05 Lux)、黑白(0.02Lux)
内部

r = 0.45

1.0 Vp-p 复合(75Ω)
变焦自动光圈与内建式DN镜头

2.8-12 mm
F1.4~360
内部
1/60秒 1/50秒
关闭 / 逆光补偿 / 高亮度补偿

自动跟踪白平衡 / 推进 / 用户1 / 用户2 /
抑制色滚 / 手动 / 推进锁定
开/关(等级可调整)

开/关(等级可调整)
镜像/亮度/对比度/锐度/色调/增益

4个区域
4个区域
英语、日本语、德语、法语、俄语、葡萄牙语、西班牙语、中文
真实日 / 夜转换，ICR
内建
内部
IP66(防水)

-30℃至+50℃(-22℉至+122℉)

-20℃至+60℃(-4℉至+140℉)
双重：直流12V(±10%)，最高190mA /

交流24V(±10%)，最高2.9W
支持

1个供模拟输出使用的标准BNC接头
约960g(含托架)

遮阳罩：银灰色RAL9006

博世安防系统 使用手册 2012.11

28 简体中文版|尺寸 室外日/夜子弹型摄像机

8-1 尺寸

Ø70(2.75)

148(5.82)

60(2.36)

120(4.72)

约. 257(10.1)

(两个)

126(4.96)

Ø80(3.14)

3-Ø6.0(0.23)

博世安防系统 使用手册 2012.11

MEMO

博世安防系统 使用手册 2012.11

MEMO

博世安防系统 使用手册 2012.11

Bosch Security Systems

www.boschsecurity.com

(c) Bosch Security Systems, 2013