Bosch VTI-4085-V521 User Manual
AN bullet 4000 IR
960H Day/Night IR Bullet Camera
2 en | Table of Contents 960H Day/Night IR Bullet Camera
Table of Contents
1 Cautions
2 Important safety instruction
3 Features
4 Components
5 Camera parts
6 Installation
6.1 Mounting position
6.2 Monitor connection
6.3 Camera adjustment
7 OSD menu structure
8 Specication
8.1 Dimensions
Bosch Security Systems User Manual 2012.11
960H Day/Night IR Bullet Camera Cautions | en 3
1 Cautions
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions;
1. This device may not cause harmful interference.
2. This device must accept any interference received,
including interference that may cause undesired operation.
Note!
This equipment has been tested and found to comply with the limits
for a Class A digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with
the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area
is likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.”
WARNING
This is a class A product. In a domestic environment this product may
cause radio interference in which case the user may be required to
take adequate measures.
CAUTION!
Any changes or modications in construction of this devies which are
not expressly approved by the party responsible for compliance could
void the user’s authority to operate the equipment.
CAUTION!
1. A regulated DC12V 500mA power supply is recommended for use with
this camera for the best picture and the most stable operation.
An unregulated power supply can cause damage to the camera.
When unregulated power supply is applied, product warranty will be
out of subject.
2. It is recommended that the camera is used with a monitor that has a
CCTV quality 75 video impedance level. If your monitor is switched to high
impedance then please adjust accordingly.
3. Do not attempt to disassemble the camera to gain access to the internal
components. Refer servicing to your dealer.
4. Never face the camera towards the sun or any bright or reective light,
which may cause smear on the picture and possible damage to the CCD.
5. Do not remove the serial sticker for the warranty service.
6. Do not expose the camera to rain or other types of liquid.
7. The apparatus must be connected to a mains socket-outlet with a
protective earthing connection.
Bosch Security Systems User Manual 2012.11
4 en | Cautions 960H Day/Night IR Bullet Camera
Correct Disposal of This Product
(Waste Electrical & Electronic Equipment)
(Applicable in the European Union and other European countries with
separate collection systems)
This marking shown on the product or its literature, indicate that
it should not be disposed with other household wastes at the end
of its working life. To prevent possible harm to the environment or
human health from uncontrolled waste disposal, please separate this
from other types of wastes and recycle it responsibly to promote the
sustainable reuse of material resources.
This product should not be mixed with other commercial wastes
purchased this product, or their local government ofce, for details of
where and how they can take item for environmentally safe recycling.
Business users should contact their supplier and check the terms and
conditions of the purchase contract.
Household users should contact either the retailer where they for
disposal.
CAUTION
RISK OF ELECTRIC SHOCK DO NOT OPEN
CAUTION:
TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER(OR BACK). NO USER. SERVICING
TO QUALIFED SERVICE PERSONNEL.
This symbol is intended to alert the user to the presence of
uninsulated “dangerous voltage” within the product’s enclosure
that may be of sufcient mangnitude to constitute a risk of
electric shock to persons.
This symbol is intended to alert the user to the presence of
important operating and maintenance(servicing) instruction in
the literature accompanying the appliance.
CAUTION!
These servicing instructions are for use by qualied service personnel
only. To reduce the risk of electric shock do not perform any servicing
other than that contained in the operating instructions unless you are
qualied to do so.
Use Class 2 Power Supply Only
Bosch Security Systems User Manual 2012.11
960H Day/Night IR Bullet Camera Important safety instructions | en 5
2 Important safety instructions
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accordance with
the manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat
registers, stoves, or other apparatus (including ampliers) that
produce heat.
9. Do not defeat the safety purpose of the polarized or groundingtype plug. A polarized plug has two blades with one wider than
the other. A grounding type plug has two blades and a third
grounding prong. The wide blade or the third prong are provided
for your safety. If the provided plug does not t into your outlet,
consult an electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched
particularly at plugs, convenience receptacles, and the point
where they exit from the apparatus.
11. Only use attachments/accessories specied by the manufacturer.
12. Use only with the cart, stand, tripod, bracket, or table specied
by the manufacturer, or sold with the apparatus. When a cart is
used, use caution when moving the cart/apparatus combination
to avoid injury from tip-over.
13. Unplug this apparatus during lightning storms or when unused for
long periods of time.
14. Refer all servicing to qualied service personnel. Servicing is
required when the apparatus has been damaged in any way, such
as power-supply cord or plug is damaged, liquid has been spilled
or objects have fallen into the apparatus, the apparatus has been
exposed to rain or moisture, does not operate normally, or has
been dropped.
Bosch Security Systems User Manual 2012.11
6 en | Features/Components 960H Day/Night IR Bullet Camera
3
Features
The camera has the following features:
•
Ultra high resolution, 960H (1/3") Sensor.
•
5-50mm lens with True Day/Night lter for optimum performance
in various lighting conditions.
•
720 TV Lines Horizontal Sensor Resolution.
•
Integrated IR LED's for discrete surveillance in dark environments.
•
Optimized IR beam pattern for a more even illumination throughout the
camera's eld of view.
•
Multi language On Screen Display (OSD) with joystick control.
•
True Wide Dynamic Range. (WDR)
•
3DNR
•
15 Privacy Zones.
•
Motion Detection.
•
External lens adjustment.
•
Cable managed bracket for secure and clean installation.
•
Vandal resistant (IK08)
•
Outdoor rated (IP66)
4 Components
Qty Description
VTI-4085-V5x1(C)
1
camera with integrated
mounting bracket
Video Output
1
Test Cable
Screws
4
(PH/1(SUS) 5x30)
Wrench
1
(M6 hex)
1 Guide Pattern
User Manual
1
(this booklet)
Bosch Security Systems User Manual 2012.11
960H Day/Night IR Bullet Camera Camera parts | en 7
5 Camera parts
➋ ➏
➊
➐ ➑ ➓➒
1
Sunshield Fixing Bolt
2
Sunshield
3
Housing Front
4
Housing Body
5
Housing Back
6
Mounting Bracket
7
Photo cell
8
Lens Knob
9
LED
10
Lens
CAUTION!
To prevent humidity problems:
1. The external lens control must be fastened rmly after
adjustments have been made.
2. The protection cap for OSD control and service cable
connector must be rmly fastened after use.
Bosch Security Systems User Manual 2012.11
➍➌ ➎
OSD joystick
Service cable connector
8 en | Installation 960H Day/Night IR Bullet Camera
6 Installation
6.1 Mounting position
To prevent injury, this apparatus must be securely attached to
the oor/wall in accordance with the installation instructions.
The image sensors in modern cameras are highly sensitive and require special
NOTICE!
care for proper performance and extended lifetime. Follow the guidelines for
optimum results with your camera:
– Do not expose to direct sunlight or bright spotlights in operating and
nonoperating conditions.
– Avoid bright lights in the eld of view of the camera. Bright lights cause
a “smearing” effect, which is visible as white lines above and below the
highlight. Prolonged exposure to bright lights may cause bleaching of the
sensor's color lters. This will be visible as colored spots in the picture
and is irreversible.
WARNING!
WARNING!
CAUTION!
The mounting surface, mounting screws/plugs, and junction box must be
stable and capable of supporting a maximum load of 10kg (22 pounds).
Mounting to an improper surface or using improper mounting material can
cause camera malfunction and is a potential safety hazard.
Make sure that appropriate mounting screws and anchors are used for the
surface to which the camera is mounted. The supplied universal mounting
screws can be used with most plastic anchors, please conrm compatibility
before mounting the camera.
To prevent humidity problems, the camera must be installed in dry conditions,
and the cable leads should be sealed after they are connected.
360°
90°
* 1st Axis
* 2nd Axis
360°
* 3rd Axis
Bosch Security Systems User Manual 2012.11
960H Day/Night IR Bullet Camera Installation | en 9
6 Installation
6.2 Monitor connection
Camera
Terminal block
Screw
Terminal
Terminal block connector
"+","-" Indication
DUAL
(DC12V/AC24V)
Female
BNC connector
Ground contact
Signal contact
2.6x3.2
(0.1x0.12)
10.16
(0.4)
5.08(0.2)
15.4(0.6)
18.2(0.71)
mm
(in.)
DUAL(DC12V/AC24V)
Regulated Power Supply
TV Monitor
Video In
*Sold separately
6.3 Camera adjustment
CAUTION!
Bosch Security Systems User Manual 2012.11
To prevent humidity problems, the camera must be installed in
dry conditions. The lens knobs (located on the bottom of the camera)
and protection cap (located on the rear of the camera) provide protection
against water ingress when fully tightened. Therefore never remove or keep
them loosened after installation. Doing so could cause water ingress and/or
condensation on the inside of the camera window.
1.
Open the protection cap on the rear of the camera
(only needed to access service monitor connection and OSD control)
2.
Connect service monitor (optional)
3.
Loosen the zoom and focus knob
4.
Adjust zoom and focus
5.
Fasten the zoom and focus knob tightly
6.
Adjust OSD settings (refer to OSD section)
7.
Disconnect service monitor cable (optional)
8.
Check rubber seal is in place on the protection cap. Close and rmly tighten
the protection cap on the rear of the camera.
10 en | OSD menu structure 960H Day/Night IR Bullet Camera
7 OSD menu structure
MAIN MENU 1st Sub 2nd Sub 3rd Sub 4th Sub
HIGH LUMINANCE
AUTO
LOW LUMINANCE
MANUAL
AT W
PUSH
USER1
USER2
MANUAL
PUSH LOCK
RETURN
MODE
SHUTTER
AGC
RETURN
SPEED 000 ~ 255
DELAY CNT 000 ~ 255
ATW FRAME x0.50, x1.00, x1.50, x2.00
ENVIRONMENT INDOOR, OUTDOOR
RETURN
B-GAIN 000 ~ 255
R-GAIN 000 ~ 255
RETURN
B-GAIN 000 ~ 255
R-GAIN 000 ~ 255
RETURN
LEVEL 000 ~ 128
RETURN
EXPOSURE
MAIN MENU 1st Sub 2nd Sub 3rd Sub 4th Sub
WHITE BAL
FLICKERLESS OFF,ON
BRIGHTNESS 000 ~ 255
MODE
AGC MAX 6, 12, 18, 24, 30, 36
DSS MAX
BRIGHTNESS
SHUTTER,
SLOW
1/50(PAL),
1/120(PAL)
1/60(NTSC),
1/100(NTSC)
1/250,1/500,
1/1000,1/2000
1/4000,1/10000,
1/100000
6, 12, 18, 24,
30, 36, 42, 44.
8
OFF, AGC, SLOW,
AGC->SLOW,
AGC->SLOW->AGC
2, 48, 16, 32,
64, 128, 256
x0.25, x0.50,
x0.75, x1.00
Bosch Security Systems User Manual 2012.11
Loading...