Bosch VTC-206 User guide

VTC-206 Series - Operation Manual

Installation

MOUNTING POSITION

In wet or moist applications, seal camera connections to ensure protection against water ingress

CONNECTION	Never face the camera towards bright (sun)light
	Not supplied
	MONITOR

		Video IN(75 Ohm)
	BNC Female
	12 VDC	12 VDC Power Supply Class2
Dimensions
		Ф40(1.57)
		1/4"-20 UNC
	78.8(3.10)	28.6(1.13)
	75.8(2.98)
		3-Ф3.2(0.13)
<![if ! IE]> <![endif]>23(0.91)	<![if ! IE]> <![endif]>50(1.97)	<![if ! IE]> <![endif]>24.8(0.98)
		mm(in)

Technical Specifications

Video

CCD Camera	1/3-inch Super HAD CCD II
Effective pixels (HxV)	976 x 582 (PAL) / 976 x 494 (NTSC)
Color Resolution	600 TVL (min.)
Electronics shutter	1/50 to 1/120,000 s (PAL) 1/60 to 1/120,000 s (NTSC)
Output Signal	1 VPP composite video, 75 ohm
Output connection	BNC connector
S/N Ratio	Greater than 50 dB
Gamma	0.45
Minimum Illumination	0.1 lx at F2.0 / 30IRE
Lens	3.6 mm fi xed

Mechanical

Housing	Compact, water resistant
Construction	Robust aluminum
Weight	68 g (2.4 oz) approximately

Electrical

Power	12 VDC, 83 mA max.
Power Supply	Not included

Environmental

Operational Temp.	-10 °C to +50	°C (+14 °F to +122 °F)
Storage Temp.	-20 °C to +60	°C (-4 °F to +140 °F)
Environment	IP67 certifi ed

Caution

These servicing instructions are for use by qualified service personnel only. To reduce the risk of electric shock do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so.

In USA and Canada, Use Class 2 Power Supply Only.

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions;

1.This device may not cause harmful interference.

2.This device must accept any interference received, including interference that may cause undesired operation.

Note

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.”

WARNING

This is a class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.

Caution

Any changes or modifications in construction of this device which are not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

CAUTION

1.A regulated DC12V 300mA power supply is recommended for use with this camera for the best picture and the most stable operation.

An unregulated power supply can cause damage to the camera. When unregulated power supply is applied, product warranty will be void.

2.The camera signal must be terminated with 75 Ohm. If your monitor is switched to high impedance then please adjust accordingly.

3.Do not attempt to disassemble the camera to gain access to the internal components. Refer servicing to your dealer.

4.Never face the camera towards the sun or any bright or reflective light, which may cause smear on the picture and possible damage to the CCD.

5.Do not remove the product label with serial number, removing the label will void the product warranty.

Correct Disposal of This Product

(Waste Electrical & Electronic Equipment)

(Applicable in the European Union and other European countries with separate collection systems)

This marking shown on the product or its literature, indicate that it should not be disposed with other household wastes at the end of its working life. To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate this from other types of wastes and recycle it responsibly to promote the sustainable reuse of material resources.

This product should not be mixed with other commercial wastes purchased this product, or their local government office, for details of where and how they can take item for environmentally safe recycling. Business users should contact their supplier and check the terms and conditions of the purchase contract. Household users should contact either the retailer where they for disposal.

CAUTION

RISK OF ELECTRIC SHOCK DO NOT OPEN

CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER(OR BACK). NO USABLE PARTS ARE

INSIDE. LEAVE SERVICING TO QUALIFED SERVICE PERSONNEL.

This symbol is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient mangnitude to constitute a risk of electric shock to persons.

This symbol is intended to alert the user to the presence of important operating and maintenance(servicing) instruction in the literature accompanying the appliance.

Important safety instructions

1)Read these instructions.

2)Keep these instructions.

3)Heed all warnings.

4)Follow all instructions.

5)Clean only with dry cloth.

6)Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

7)Do not install near any heat sources such as radiators, heat registers,stoves, or other apparatus (including amplifiers) that produce heat.

8)Do not defeat the safety purpose of the polarized or

groundingtype plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

9) Protect the power cord from being walked on or pinched

particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

10)Only use attachments/accessories specified by the manufacturer.

11)Use only with the cart, stand, tripod, bracket, or table specified by

the manufacturer, or sold with the apparatus. When a cart is used,

use caution when moving the cart/apparatus combination to avoid injury from tip-over.

12) Unplug this apparatus during lightning storms or when unused for long periods of time.

13) Refer all servicing to qualified service personnel. Servicing is

required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.