Page 1
AN trafc 4000 IR
960H IR License Plate Bullet Camera
en User Manual
Page 2
2 en | Table of Contents 960H IR License Plate Bullet Camera
Table of Contents
1 Cautions
2 Important safety instruction
3 Features
4 Components
5 Camera parts
6 Installation
6.1 Mounting position
6.2 Monitor connection
7 Installation guideline
7.1 Camera height
7.2 Camera angles
7.3 Capture zone
7.4 Lane width
7.5 Speed
8 Camera conguration
9 OSD menu structure
10 Specication
10.1 Dimensions
Bosch Security Systems User Manual 2012.11
Page 3
960H IR License Plate Bullet Camera Cautions | en 3
1 CAUTIONS
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions;
1. This device may not cause harmful interference.
2. This device must accept any interference received,
including interference that may cause undesired operation.
Note!
This equipment has been tested and found to comply with the limits
for a Class A digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with
the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area
is likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.”
WARNING
This is a class A product. In a domestic environment this product may
cause radio interference in which case the user may be required to
take adequate measures.
CAUTION!
Any changes or modications in construction of this devies which are
not expressly approved by the party responsible for compliance could
void the user’s authority to operate the equipment.
CAUTION!
1. A regulated DC12V 500mA power supply is recommended for use with
this camera for the best picture and the most stable operation.
An unregulated power supply can cause damage to the camera.
When unregulated power supply is applied, product warranty will be
out of subject.
2. It is recommended that the camera is used with a monitor that has a
CCTV quality 75 video impedance level. If your monitor is switched to high
impedance then please adjust accordingly.
3. Do not attempt to disassemble the camera to gain access to the internal
components. Refer servicing to your dealer.
4. Never face the camera towards the sun or any bright or reective light,
which may cause smear on the picture and possible damage to the CCD.
5. Do not remove the serial sticker for the warranty service.
6. Do not expose the camera to rain or other types of liquid.
7. The apparatus must be connected to a mains socket-outlet with a
protective earthing connection.
Bosch Security Systems User Manual 2012.11
Page 4
4 en | Cautions 960H IR License Plate Bullet Camera
Correct Disposal of This Product
(Waste Electrical & Electronic Equipment)
(Applicable in the European Union and other European countries with
separate collection systems)
This marking shown on the product or its literature, indicate that
it should not be disposed with other household wastes at the end
of its working life. To prevent possible harm to the environment or
human health from uncontrolled waste disposal, please separate this
from other types of wastes and recycle it responsibly to promote the
sustainable reuse of material resources.
This product should not be mixed with other commercial wastes
purchased this product, or their local government ofce, for details of
where and how they can take item for environmentally safe recycling.
Business users should contact their supplier and check the terms and
conditions of the purchase contract.
Household users should contact either the retailer where they for
disposal.
CAUTION
RISK OF ELECTRIC SHOCK DO NOT OPEN
CAUTION:
TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER(OR BACK). NO USER. SERVICING
TO QUALIFED SERVICE PERSONNEL.
This symbol is intended to alert the user to the presence of
uninsulated “dangerous voltage” within the product’s enclosure
that may be of sufcient mangnitude to constitute a risk of
electric shock to persons.
This symbol is intended to alert the user to the presence of
important operating and maintenance(servicing) instruction in
the literature accompanying the appliance.
CAUTION!
These servicing instructions are for use by qualied service personnel
only. To reduce the risk of electric shock do not perform any servicing
other than that contained in the operating instructions unless you are
qualied to do so.
Use Class 2 Power Supply Only
Bosch Security Systems User Manual 2012.11
Page 5
960H IR License Plate Bullet Camera Important safety instructions | en 5
2 Important safety instructions
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accordance with
the manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat
registers, stoves, or other apparatus (including ampliers) that
produce heat.
9. Do not defeat the safety purpose of the polarized or groundingtype plug. A polarized plug has two blades with one wider than
the other. A grounding type plug has two blades and a third
grounding prong. The wide blade or the third prong are provided
for your safety. If the provided plug does not t into your outlet,
consult an electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched
particularly at plugs, convenience receptacles, and the point
where they exit from the apparatus.
11. Only use attachments/accessories specied by the manufacturer.
12. Use only with the cart, stand, tripod, bracket, or table specied
by the manufacturer, or sold with the apparatus. When a cart is
used, use caution when moving the cart/apparatus combination
to avoid injury from tip-over.
13. Unplug this apparatus during lightning storms or when unused for
long periods of time.
14. Refer all servicing to qualied service personnel. Servicing is
required when the apparatus has been damaged in any way, such
as power-supply cord or plug is damaged, liquid has been spilled
or objects have fallen into the apparatus, the apparatus has been
exposed to rain or moisture, does not operate normally, or has
been dropped.
Bosch Security Systems User Manual 2012.11
Page 6
6 en | Features/Components 960H IR License Plate Bullet Camera
3
Features
The camera has the following features:
•
1/3" 960H SONY EXview HAD CCD ll
•
720 TV Lines Horizontal Sensor Resolution.
•
Adjustable high power IR beam in combination with special light lter
technology for reliable license plate capturing in all lighting and weather
conditions.
•
5~50mm varifocal lens providing variable capture range of 4.8 to 27
meters. (16 to 91 feet)
•
Multi language On Screen Display (OSD) with joystick control.
•
Plate capture up to 120 km/h (75 mph)External lens adjustment.
•
Cable managed bracket for secure and clean installation.
•
Vandal resistant (IK08)
•
Outdoor rated (IP66)
This product works only in countries where license plates have a reective
NOTICE!
coating. License plates without a reective coating will not be visible.
Capture range, speed and quality depends on the character font and size
used on the license plate. Performance may be degraded by license plates
with a poor coating/printing or dirt. Vibration or shaking of the camera will
also degrade the performance, especially with a long capture distance. Make
sure the camera is mounted with suitable mounting materials on a stable
surface, and shorten the capture distance where possible.
4 Components
Qty Description Qty Description
1
1
4
VLR-4075-V5x1
camera with
integrated
mounting bracket
Video Output
Test Cable
Screws
(PH/1(SUS)
5x30)
Wrench
1
(M6 hex)
1 Guide Pattern
User Manual
1
(this booklet)
Bosch Security Systems User Manual 2012.11
Page 7
960H IR License Plate Bullet Camera Camera parts | en 7
5 Camera parts
➐ ➒➑
1
Sunshield Fixing Bolt
2
Sunshield
3
Housing Front
4
Housing Body
5
Housing Back
check rubber seal is in place on the protection cap, close and
➋ ➏
➊
➍➌ ➎
6
Mounting Bracket
7
Lens Knob
8
LED
9
Lens
After using the OSD joystick or Service cable connector,
rmly tighten it to prevent water ingress.
OSD joystick
Service cable connector
After lens adjustment, fasten the zoom and focus knob tightly
Bosch Security Systems User Manual 2012.11
to prevent water ingress.
Page 8
8 en | Installation 960H IR License Plate Bullet Camera
6 Installation
6.1 Monitor connection
To prevent injury, this apparatus must be securely attached to
the oor/wall in accordance with the installation instructions.
The image sensors in modern cameras are highly sensitive and require special
NOTICE!
care for proper performance and extended lifetime. Follow the guidelines for
optimum results with your camera:
– Do not expose to direct sunlight or bright spotlights in operating and
nonoperating conditions.
– Avoid bright lights in the eld of view of the camera. Bright lights cause
a “smearing” effect, which is visible as white lines above and below the
highlight. Prolonged exposure to bright lights may cause bleaching of the
sensor's color lters. This will be visible as colored spots in the picture
and is irreversible.
WARNING!
WARNING!
CAUTION!
The mounting surface, mounting screws/plugs, and junction box must be
stable and capable of supporting a maximum load of 10kg (22 pounds).
Mounting to an improper surface or using improper mounting material can
cause camera malfunction and is a potential safety hazard.
Make sure that appropriate mounting screws and anchors are used for the
surface to which the camera is mounted. The supplied universal mounting
screws can be used with most plastic anchors, please conrm compatibility
before mounting the camera.
To prevent humidity problems, the camera must be installed in dry conditions,
and the cable leads should be sealed after they are connected.
360°
90°
* 1st Axis
* 2nd Axis
360°
* 3rd Axis
Bosch Security Systems User Manual 2012.11
Page 9
960H IR License Plate Bullet Camera Installation | en 9
6 Installation
6.2 Monitor connection
Female
BNC connector
Ground contact
Camera
Signal contact
Terminal block
Screw
Terminal
Terminal block connector
"+","-" Indication
DUAL
(DC12V/AC24V)
2.6x3.2
(0.1x0.12)
10.16
(0.4)
5.08(0.2)
15.4(0.6)
18.2(0.71)
mm
(in.)
DUAL(DC12V/AC24V)
Regulated Power Supply
TV Monitor
Video In
*Sold separately
6.3 Camera adjustment
CAUTION!
Bosch Security Systems User Manual 2012.11
To prevent humidity problems, the camera must be installed in
dry conditions. The lens knobs (located on the bottom of the camera)
and protection cap (located on the rear of the camera) provide protection
against water ingress when fully tightened. Therefore never remove or keep
them loosened after installation. Doing so could cause water ingress and/or
condensation on the inside of the camera window
1.
Open the protection cap on the rear of the camera (only needed to access
service monitor connection and OSD control)
2.
Connect service monitor (optional)
3.
Loosen the zoom and focus knob
4.
Adjust zoom and focus
5.
Fasten the zoom and focus knob tightly
6.
Adjust OSD settings (refer to Camera Conguration section)
7.
Disconnect service monitor cable (optional)
8.
Check rubber seal is in place on the protection cap. Close and rmly tighten
the protection cap on the rear of the camera.
Page 10
960H IR License Plate Bullet Camera Installation guideline | en 10
7 Installation guideline
7.1
Camera height
• The camera has a 5~50mm varifocal lens providing variable capture
range of 4.8 to 27 meters (16 to 91 feet)
• The camera height (the height where the camera is mounted) must
be considered when determining capture distance.
Below table illustrates how the camera height inuences the capture distance
(camera height and horizontal distance are examples).
Camera height (m/ft) Horizontal Distance (m/ft) Capture Distance (m/ft)
1 / 3.3 4 / 13.1 4.1 / 13.5
1.5 / 4.9 4 / 13.1 4.3 / 14.1
2 / 6.6 4 / 13.1 4.5 / 14.8
2.5 / 8.2 4 / 13.1 4.7 / 15.4
3 / 9.8 4 / 13.1 5 / 16.4
7.2
Camera angles
• It is advised to mount the camera at a horizontal and vertical angle of less than
30 degrees. A greater angle will distort the characters of the license plate and will
reduce the capture performance. If the mounting position is xed, the capture angle
can be reduced by increasing the capture distance.
H-angle less than 30˚V-angle less than 30˚
Bosch Security Systems User Manual 2012.11
Page 11
11 en | Installation guideline 960H IR License Plate Bullet Camera
7 Installation guideline
Below table illustrates how the camera height inuences the capture distance
(camera height and horizontal distance are examples).
Camera height (m/ft) Horizontal Distance (m/ft) V-angle (º)
1 / 3.3 4 / 13.1 14
1.5 / 4.9 4 / 13.1 21
2 / 6.6 4 / 13.1 27
2.5 / 8.2 4 / 13.1 32 (exceeds the advised
3 / 9.8 4 / 13.1 37(exceeds the advised
7.3
Capture zone
- Wide angle provides shorter capture distance and increased capture angle,
but could result in the better image quality and stability.
- Tele angle provides longer capture distance and reduced capture angle,
but could result in reduced image quality and stability.
- While a license plate can still be read by human eye, license plate
capture software might not be able to recognize it.
mounting angle)
mounting angle)
WIDE SETTING -66.5 @ f=5mm
TELE SETTING -7.4 @ f=50mm
WIDE END -66.5 @ f=5mm
5M 10M 15M 20M 25M 30M
License plate readable by
o
TELE END -7.4 @ f=50mm
license plate
capture software
License plate readable
by human eye
o
What will be the plate look like on screen?
(All scenes taken with high-beam)
Position "A" with WIDE SETTING
Position "B" with TELE SETTING
Position "B" with WIDE SETTING
Position "C" with TELE SETTING
Bosch Security Systems User Manual 2012.11
Page 12
960H IR License Plate Bullet Camera Installation guideline | en 12
7.4
Lane width
• Narrow lanes = less variation in plate location.
• Wider lanes = more variation in plate location.
• Lens should cover entire width of the lane.
• Ensure horizontal eld of view is wide enough.
7.5
Speed
• Camera can capture moving vehicles up to 120 km/h (75 mph).
• Keep camera as low as possible.
• Minimize horizontal angle.
• Zoom in the lens as close as possible.
Up to 75 mph
Bosch Security Systems User Manual 2012.11
Page 13
13 en | OSD menu structure 960H IR License Plate Bullet Camera
8 Camera conguration
After the camera is properly installed, the focus and zoom should be adjusted,
and OSD menu should be congured to optimize the camera's performance. To
enter the OSD menu, press the OSD joystick located on the rear of the camera.
Step1: The rst time the camera is turned on, the camera is in installation mode. In this mode,
the camera will display the complete monochrome picture (not only the license plate).
This will help to correctly aim and focus the camera on the target object. If the camera
is not in installation mode, change MODE from LICENSE-PLATE to INSTALLATION in the
OSD menu.
Step2: Adjust the zoom and focus (and camera position if needed) to the target object.
Step3: Change the camera mode from INSTALLATION to LICENSE-PLATE in the OSD menu. In
this mode, the camera will only display reective objects such as the license plate.
Step4: Adjust the SHUTTER value (= shutter speed) in order to prevent over- or underexposure
of the license plate. In applications with short capture distance, the IR intensity may be
reduced by lowering the LED level in the OSD menu to further prevent overexposure.
Note that if the camera is installed outdoors, the license plate image may be slightly
different during daytime and nighttime. This effect will increase when lowering the LED
level, or when using a long capture distance.
Step5: If required, the image may be inverted by turning on NEGATIVE in the OSD menu.
In negative mode, light areas in the image will appear dark and vice versa. In some
applications this may improve the readability of the license plate.
Step6: Exit the OSD menu.
9 OSD menu structure
MAIN MENU 1st Sub
MODE
SHUTTER
NEGATIVE
LED LEVEL 0~10
LANGUAGE English, Russian, Spanish, German, French, Portuguese
EXIT
* SHUTTER:
INSTALLATION
LICENSE-PLATE
---- (INSTALL MODE)
1/250, 1/500,
1/1000~1/10000 (adjusted 1/500sec measure)
1/30K,1/50K,1/70K,
1/90K, 1/100K
OFF
ON
adjusted when LICENSE-PLATE MODE is performed.
Bosch Security Systems User Manual 2012.11
Page 14
14 en | Specication 960H IR License Plate Bullet Camera
10 Specication
Model
Image Device
Scanning System
Scanning Frequency
H. Sensor Res.
Actual H. Res.
Total Pixels
Effective Pixels
S/N Ratio
Min. Illumination
Sync. System
Gamma
Video Output
Lens
Lens focal length
Aperture
Lens adjustment
Electronic Shutter
Function
Language
OSD
OSD Control
IR LED 850 nm, up to 28 m
IP Rating
Operating Temperature
Storage Temperature
Power Consumption
Cable
Management Bracket
Video interface
Weight
Housing material Casted/machined Aluminium
Paint color White RAL9003
Vandal resistant Yes (IK08)
Outdoor rated Yes (IP66)
Bosch Security Systems User Manual 2012.11
VLR-4075-V521(NTSC) VLR-4075-V511(PAL)
1/3" 960H SONY EXview HAD CCD ll
2 : 1 Interlace
15.734 KHz(H),59.94 Hz(V) 15.625 KHz(H), 50 Hz(V)
720TVL
620TVL
1028(H) x 508(V) 1028(H) x 596(V)
976(H) x 494(V) 976(H) x 582(V)
More than 50dB (AGC Off)
0 Lux (IR LED On)
Internal
r = 0.45
1.0 Vp-p Composite (75Ω)
Varifocal Auto IRIS & DC Lens Built-in
5~50mm
F1.4~360
External
1/250 ~ 1/100,000
Installation Mode, License Plate Mode, Shutter speed
Changeable, Focus Adjust Mode, Negative Image
English, Russian, Spanish,
German, French, Portuguese
Built-in
External
IP66 (Water resistant)
-30 ºC to +50 ºC (-22 ºF to +122 ºF)
-20˚C to +60˚C (-4˚F to +140˚F)
Dual : DC12V(±10%), Max. 600 mA /
AC24V(±10%), Max. 7.7 W
Yes
1 standard BNC connector for analog output
Approx. 1.9kg(including bracket)
Page 15
960H IR License Plate Bullet Camera Dimensions | en 15
10-1 Dimensions
Ø95(3.74)
173(6.85)
150(5.9)
160(6.29)
Ø110(4.33)
Bosch Security Systems User Manual 2012.11
Approx. 310(12.2)
4-Ø6.0(0.23)
mm
(in.)
Page 16
Bosch Security Systems
www.boschsecurity.com
(c) Bosch Security Systems, 2013
Loading...