Bosch VBN-4075-C21, VBC-4075-C21 Installation

Bosch

DINION 4000 - Quick Install

1/2

24 VAC or 12 VDC class 2 power supply

5 mm

(0.2 in)

AWG16 to 22 stranded or AWG16 to 26 solid wire

VIDEO

ARM

12 VD

1 2 3

5 6

230 VAC power

VIDEO

LARM

2 3 4

Video BNC 75 Ohm

VIDEO

ARM

12 VD

1 2 3

5 6

Back focus

(VBN version only)

Alarm in

not used

Relay out contact 2

Alarm in ground

not used

Relay out contact 1

Bosch

Unlock

Bos

1Safety

1.1 Safety precautions

DANGER!

High risk: This symbol indicates an imminently hazardous situation such as "Dangerous Voltage" inside the product. If not avoided, this will result in an electrical shock, serious bodily injury, or death.

WARNING!

Medium risk: Indicates a potentially hazardous situation. If not avoided, this could result in minor or moderate bodily injury.

CAUTION!

Low risk: Indicates a potentially hazardous situation. If not avoided, this could result in property damage or risk of damage to the unit.

CAUTION!

The Low Voltage power supply unit must comply with EN60950 / UL60065. The power supply must be a SELV-LPS unit or a SELV - Class 2 unit (Safety Extra Low Voltage - Limited Power Source).

CAUTION!

Installation should only be performed by qualiﬁed service personnel in accordance with the National Electrical Code NEC800 (CEC Section 60) or applicable local codes.

1.2 Important safety instructions

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions

5. Do not use this apparatus near water.

6. Clean only with a dry cloth.

7. Install in accordance with the manufacturer's instructions.

8. Do not install unit near any heat sources such as radiators, heat registers, stoves, or other apparatus (including ampliﬁers) that produce heat.

9. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

10. Only use attachments/accessories speciﬁed by the manufacturer.

11. Unplug this apparatus during lightning storms or when unused for long periods of time.

12. Refer all servicing to service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

1.3 FCC & ICES compliance

FCC & ICES Information

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: – reorient or relocate the receiving antenna; – increase the separation between the equipment and

receiver;

– connect the equipment into an outlet on a circuit different

from that to which the receiver is connected;

– consult the dealer or an experienced radio/TV technician

for help.

Intentional or unintentional modiﬁcations, not expressly approved by the party responsible for compliance, shall not be made. Any such modiﬁcations could void the user's authority to operate the equipment. If necessary, the user should consult the dealer or an experienced radio/television technician for corrective action.

Focal length

1.4 Bosch notices

Disposal - Your Bosch product was developed and

manufactured with high-quality material and components that can be recycled and reused. This symbol means that electronic and electrical appliances, which have reached the end of their working life, must be collected and disposed of separately from household waste material. Separate collecting systems are usually in place for disused electronic and electrical products. Please dispose of these units at an environmentally compatible recycling facility, per European

Directive 2002/96/EC

Optical elements

Optical elements are sensitive and should be protected at all times. Do not allow objects to come into contact with glass surfaces and do not touch optical elements with your ﬁngers.

Trademarks

All hardware and software product names used in this document are likely to be registered trademarks and must be treated accordingly.

Note

Bosch Security Systems accepts no liability for damage resulting directly or indirectly from faults, incompleteness or discrepancies between the user guide and the product described.

More information

For more information please contact the nearest Bosch Security Systems location or visit www.boschsecurity.com

Focus

AM18-Q0643

Analog Camera Menus Setup menu | en 1

1Setup menu

Press the center button of the control pad to access the SETUP menu.

Set

– Press the up or down buttons to move the cursor through the menus.

– Press the right or left buttons to change values.

– When the symbol is shown, press the center button to select an

item or open a submenu.

Navigation items at the bottom of the screen

– To move to the continuation of a menu, select NEXT. – To return to the previous menu, select BACK or RETURN. – To save changes, select SAVE ALL. – To close the SETUP menu, select EXIT.

Analog Camera Menus Setup menu | en 2

1.1 Main menu

LENS Iris setting

SHUTTER/AGC Auto and manual exposure control

WHITE BAL White balance setting

BACKLIGHT Backlight compensation setting

PICT ADJUST Image adjustment setting

DYN Dynamic range setting

MOTION DET Video motion detection setting

PRIVACY Privacy masking setting

DAY/NIGHT Day/Night setting

DNR Digital noise reduction

CAMERA ID Camera identification

SYNC Synchronization mode setting

LANGUAGE Language setting

CAMERA RESET Restores all factory default values

SAVE ALL Saves all settings

1.1.1 Lens menu

LENS MANUAL

AUTO TYPE DC

MODE OPEN, CLOSE, AUTO

SPEED 0 - 255

RETURN

Analog Camera Menus Setup menu | en 3

1.1.2 Shutter/AGC (Automatic Gain Control) menu

SHUTTER/AGC AUTO HIGH LUMINANCE

MODE SHUT+AUTO IRIS, AUTO

IRIS

BRIGHTNESS 0 - 255

RETURN

LOW LUMINANCE

MODE AGC, OFF

BRIGHTNESS x0.25, x0.5, x0.75, x1.0

RETURN

MANUAL MODE SHUT+AGC

SHUTTER 1/60, 1/120, 1/250, 1/500,

1/1000, /2000, 1/4000, 1/ 10000 (NTSC) 1/50, 1/100, 1/250, 1/500, 1/1000, 1/2000, 1/4000, 1/ 10000 (PAL)

AGC 6, 12, 18, 24, 30, 36, 42,

44.8

RETURN

Analog Camera Menus Setup menu | en 4

1.1.3 White balance menu

WHITE BAL ATW SPEED 0 - 255

DELAY CNT 0 - 255

ATW FRAME x0.5, x1.0, x1.5, x2.0

ENVIRONMENT INDOOR, OUTDOOR

RETURN

PUSH

USER1 B-GAIN 0 - 255

R-GAIN 0 - 255

RETURN

USER2 B-GAIN 0 - 255

R-GAIN 0 - 255

RETURN

ANTI CR

MANUAL LEVEL 0 - 255

RETURN

PUSH LOCK

– ATW (Auto Tracking White balance) and PUSH (Full pull-in: 1,800 K to

10,500 K) continuously analyze color temperature.

– Use ANTI CR (Anti Color Rolling) when certain types of fluorescent light

cause the picture to periodically change color.

– Use PUSH LOCK with a reference white object filling the screen.

Analog Camera Menus Setup menu | en 5

1.1.4 Backlight menu

BACKLIGHT OFF

BLC

HLC

– Use BLC (Back Light Compensation) to see a dark object in front of a

bright background.

– Use HLC (High Light Compensation) to darken highlights and avoid

image wash-out (for example, car headlights).

1.1.5 Picture adjust menu

PICT ADJUST MIRROR ON, OFF

BRIGHTNESS 0 - 255

CONTRAST 0 - 255

SHARPNESS 0 - 255

HUE 0 - 255

GAIN 0- 255

RETURN

1.1.6 Dynamic range setting menu

DYN OFF

ON LUMINANCE LOW, MID, HIGH

CONTRAST LOW, MIDLOW, MID,

MIDHIGH, HIGH

RETURN

– Use DYN (Dynamic range setting) to improve dynamic range by highlight

compression and contrast enhancement.

Analog Camera Menus Setup menu | en 6

1.1.7 Motion detection menu

MOTION DET OFF

ON DETECT SENSE 0 - 127

BLOCK DISP OFF, ON, ENABLE

MONITOR AREA OFF, ON

AREA SEL 1 - 4

TOP 0 - 244 (NTSC), 288 (PAL)

BOTTOM 0 - 244 (NTSC), 288 (PAL)

LEFT 0 - 474 (NTSC), 468 (PAL)

RIGHT 0 - 474 (NTSC), 468 (PAL)

RETURN

– The ENABLE function sets the regions/blocks where motion detection

does not work.

– To exit the BLOCK DISP ENABLE function, press straight down on the

set button for a longer time.

1.1.8 Privacy masking menu

PRIVACY OFF

ON AREA SEL 1 - 8

TOP 0 - 244 (NTSC), 288 (PAL)

BOTTOM 0 - 244 (NTSC), 288 (PAL)

LEFT 0 - 474 (NTSC), 468 (PAL)

RIGHT 0 - 474 (NTSC), 468 (PAL)

COLOR 1 - 8

TRANSP 0.00, 0.50, 0.75, 1.00

MOSAIC OFF, ON

RETURN

Analog Camera Menus Setup menu | en 7

Area selection for motion or privacy masks

Select area 1, 2, 3 or 4 (8).

– Top: extend or reduce upper limit of the detection area.

– Bottom: extend or reduce bottom limit of the detection area.

– Left: extend or reduce left limit of the detection area.

– Right: extend or reduce right limit of the detection area.

TOP

LEFT RIGHT

BOTTOM

reduce extend

RIGHT

1.1.9 Day/night menu

DAY/NIGHT AUTO BURST OFF, ON

DELAY CNT 0 - 255

DAY->NIGHT 0 - 255

NIGHT->DAY 0 - 255

RETURN

COLOR

B/W BURST OFF, ON

EXT OFF, EXT1, EXT2

RETURN

– When EXT is on the IR cut-off filter is switched by an external input.

– With EXT1 the camera switches to night mode when alarm-in is high;

with EXT2 the camera switches to night mode when alarm-in is low.

– The output relay closes when the camera switches to NIGHT mode.

Analog Camera Menus Setup menu | en 8

1.1.10 Digital noise reduction menu

DNR DNR MODE OFF, Y, C, Y/C

Y LEVEL 0 - 15

C LEVEL 0 - 15

RETURN

1.1.11 Camera identification menu

CAMERA ID OFF

RETURN

When ON is selected, a virtual keyboard appears on the screen. Use the control pad to move to the character you want and select it. Repeat this to enter the camera ID you desire. You can enter up to 52 characters.

1.1.12

LANGUAGE ENGLISH, JAPANESE, GERMAN, FRENCH, RUSSIAN,

Language menu

PORTUGUESE, SPANISH, SIMPLIFIED CHINESE

– Only 4 areas are available if MONITOR AREA of motion detection is on.