Bosch SRS56L02GB, SRS56L08GB User Manual

en

5600 053 299 G Summary of instructions for dishwasher

Brief and handy: everything your dishwasher needs...

Before using for the first time, read the installation and operating instructions!

Fill with special salt

Fill with rinse aid

Fill with detergent

Select programme

Switch on appliance

Press On/Off switch, running time of the chosen programme appears

Switch off the appliance Everything O.K...

When the display shows 0 (end of programme), press On/Off switch

Set the water softening system *

Read off the setting ...

Find out the water hardness at your water utility company and enter

*only before using the dishwasher for the first time or if the water hardness changes

Descaling (not required for set value 0 !)...

Lift off the cover.

Everything is sparkling clean ...

Press mark 1, lift up lid 2.

							Quickly sorted ...
							and then set
A			B		C		± Hold down programme button B and switch on the main
							switch, then release the buttons. The display of button B
		Reset					and the number 4 set by the factory flash.

±Each time button B is depressed, the setting increases by one; if 7 has been reached, the display jumps back to 0.

±Switch off the main switch. The selected setting has been stored in the appliance.

Only before using				Then pour max.	Close the
the appliance for				1.5 kg of salt	cover. Wash
the first time, pour				(never deter-	immediately.
approx. 1 litre of				gent!) through
water into the salt				the funnel.
opening.

Refill whenever level indicator is light!

Pour in	Close the
rinse aid.	lid. CLICK!

Very dirty dishes, a lot of detergent ...

If required, open the lid (press the pin).

Quick, economical or intensive ...

Warning,

combination products are not suitable for all programmes, follow manufacturer's instructions.

Pour in	Push the lid
detergent.	shut, press.
	PLOP!

Programme overview

This overview lists the max. possible number of programmes. The programmes supplied with your appliance are indicated on the fascia.

The programme data are values measured in the laboratory in compliance with Standard EN 50242. Deviations is practice are possible.

		Intensive		Auto		Eco		Gentle		Quick		Prerinse
		70		55 /65		50		40		35
Duration in minutes		109	95±145		155		75		30		20
Electricity consumption in kWh		1,35	0,95±1,30		0,80		0,65		0,50		0,10
Water consumption in litres		20	11±18		13		14		10		4
with Aquasensor		17	±		±		11		±		±

Additional programmes **	Increased flexibility ...
Time selection		Upper basket cleaning
...switches on as soon as		...Only the crockery in the
you press the time		upper basket is cleaned

h.

selection button: Alters the programme start in hourly steps

** on some models

	Maintenance and care		For perfect rinsing results ...			Cleaning the waste-water pump *
	Strainers ...	Rotate filter	rinse under	Insert ...	Screw in filter system	* With some models
						± Ladle out water and remove filters
	Check, if	cylinder, remove	flowing water ...		NOTE MARK!
	required, clean	filter system ...				± Unscrew cover (Torx T20)
						± Check area of fan impeller for foreign objects
						± Screw in cover and insert filters
	Spray arms ...	Pull lower arm	Unscrew upper	Clean spray nozzles	Insert lower arm ...
	Remove	upwards ...	arm ...	under flowing water
	blockages/deposits			(perhaps with
				toothpick) ...
					Screw in upper arm
	Eliminating minor faults yourself ...		... Self±help pays!

	Fault	Possible Cause	Remedy
	Residual water in the device	Waste-water pump blocked	Clean waste-water pump (see above).
		Programme not yet ended	Close and switch on appliance or
			terminate programme (see Terminating
			the programme).
	Device does not work/stops	Supply fitting not open	Open supply fitting.
		Supply hose kinked	Lay supply hose without kinks.
		Supply fitting jammed or calcified	1. Unscrew water connection.
			2. Clean filter in the water connection.
			3. Flow rate must be min. 9 l/min when
			the water inlet is open.
			If the flow rate is less, replace the
			supply fitting.
	Plastic parts / parts of	Too little cleaning product	Follow manufacturer's specifications
		Discoloration caused by food colourings	(detergent).
	dishes discoloured
			Discoloration is quite safe; fades after
		(tomato sauce)
			subsequent rinse cycles.
	Cutlery rusty	Cutlery not rust-proof	Use dishwasher-proof cutlery.
		Hard knife blades are more susceptible
		Extraneous rust	Never wash rusting parts in the
			appliance.

Fault	Possible Cause	Remedy
Dishes not clean	Utensils are situated too close to each	Spread out the utensils, avoid contact
Sand or grainy residues	other or on top of each other	between the utensils.
		Follow manufacturer's specifications
on dishes	Too little cleaning product
		(detergent).
	Unsuitable programme selected	Select more intensive programme.
	Spray nozzles blocked	Clean spray arms (see above).
	Filters dirty, not installed securely	Clean the strainers (see above).
	Spray arms blocked	Arrange the utensils so that the spray
		arms can rotate freely.
Stains and streaks	Rinse aid dosage too high / too low	Streaks: Reduce dosage.

Milky residues on dishes (can be removed)

Milky film, glasses cloudy / dull (cannot be removed)

Water softening system incorrectly set; no special salt

Glasses not dishwasher-proof.

Water or limescale stains: Increase dosage.

Set water softening system correctly.

Refill with special salt.

Use dishwasher-proof glasses.

Use glass-friendly cleaning products.

Further advice can be found in the instruction manual

Stopping the programme ...

Press and hold the two

reset buttons simultaneously for approximately 3 seconds while the programme is running (RESET)

		Loading the dishwasher correctly ...
	º0º appears	Arrange dishwasher-proof utensils (having removed any ash, wax, grease, ink, sticky labels; remove,
	Switch off the appliance.	large remnants of jam, dairy products and food) according to the operating instructions and check that
	The programme will stop	the spray arms can rotate freely.
	after 1 minute