Bosch SpotBot-BLE ShockWatch User Manual

®

TM

PRODUCT MANUAL

®

TM

PRODUCT MANUAL

CONTENTS

1. Introduction and Intended Use 4

1.1. Intended Use 4

2. Technical Specications 5

2.1. Measured Parameters 5

2.2. Device Specication 5

2.3. Operating Conditions 5

2.4. Resolutions 5

2.5. Accuracies 6

3. Mounting the SpotBot BLE 7

3.1. Mounting with Screws 7

3.2. Mounting with Adhesive Tape 7

4. Operation 8

4.1. Installing the App 8

4.2. Connecting to the SpotBot BLE 8

4.3. Conguring the SpotBot BLE 9

4.4. Settings 11

4.5. Reading and Transferring Data 13

4.6. Blinking Patterns 15

5. Maintenance 16

5.1. Changing the Battery 16

6. About these Operating Instructions 18

6.1. Meanings of the used signal words 18

6.2. Meanings of INFO and TIP 18

7. Safety and Environment 19

7.1. Radio Frequency Radiation Exposure and Further Information 19

7.2. Disposal 19

2

®

TM

PRODUCT MANUAL

CONTENTS

8. Regulatory Notices 20

8.1. Recycling 20

8.2. EU Declaration of Conformity 20

8.3. Federal Communications Commission (FCC) Notice 20

8.4. ISED Canada (IC) Notice 21

8.5. IMDA Singapore Notice 21

8.6 Japanese Radio Law ( ) Notice 21

8.7. China Notice 21

8.8 Australia Notice 21

8.9. Malaysia Notice 21

8.10. Philippines Notice 21

8.11. Thailand Notice 21

8.12. Bluetooth® 22

8.13. Other Certications 22

8.14. Export Restrictions 22

3

®

TM

PRODUCT MANUAL

1. Introduction and Intended Use

By being attached to the shipment and measuring and recording relevant parameters like
temperature, humidity, tilt and shock, the SpotBot BLE makes the delivery process of goods
visible and traceable. These measurements are then documented and visualized through a mobile
application. Since the limits of each parameter can be individually congured, any violation of these
limits is traceable and clearly assignable to the stations throughout the entire transport process.

1.1. Intended Use

The SpotBot BLE is designed according to the information provided in the data sheet. Any use or
operation which requires specic requirements and standards which aren’t explicitly mentioned in the
data sheet must be validated and tested on customer’s own risk.

1 Surface: place your shipment code here (see INFO below).
2 Button (see chapter 6 Operation)
3 LED (green/red) (see Blinking Patterns on page 17)
4 Mounting holes (4x) (see Mounting the SpotBot BLE on page 9)
5 Battery (see Changing the Battery on page 18)
6 Mounting plate (see Mounting the SpotBot BLE on page 9)

INFO

Consider that the humidity sensor should not be covered by labels or stickers.
Otherwise the humidity measurement doesn’t work.

FIGURE 1 I Overview SpotBot BLE

4

®

TM

PRODUCT MANUAL

2. Technical Specications

2.1. Measured Parameters

Temperature • Humidity • Tilt • Shock

2.2. Device Specication

TABLE 1 I DEVICE SPECIFICATIONS

Attribute Value

Dimension (W x H x D): 91mm x 102mm x 25mm

Weight: 100g

Power Supply: CR 123A Lithium Battery

Battery Lifetime: 2 Years (10min measuring cycle, +25°C)

Enclosure Protection Class: IP 54

Electrical Protection Class: III

Measuring Cycle (selectable): 1 min to 4 hours

Memory Capacity:

Communication: Bluetooth 4.0 (Low Energy)

Bluetooth Frequency Band: 2.402 to 2.480 GHz

Transmission Power: 5 dBm

Recommended Storage Temperature: 0°C to +40°C

2 Years (15 min. measuring cycle, see Logging Interval
on page 13)

2.3. Operating Conditions

TABLE 2 I OPERATING CONDITIONS

Attribute Range

Operating Temperature Range: -25°C to +80°C

Humidity Range: 0% rH to 100% rH (non-condensing)

Shock/Acceleration Range: ±8.0 g per axis; ±13.8g three-dimensional

2.4. Resolutions

TABLE 3 I CONFIGURABLE RESOLUTIONS

Attribute Resolution

Temperature: 0.5°C

Humidity: 1% rH

Tilt: 0° to 150° (30° steps)

Shock: 0.1g

5

®

TM

2.5. Accuracies

TABLE 4 I ACCURACIES

Attribute Value

Temperature 0.5°C

Humidity: ±5 % rH / ±10 % rH

Acceleration/Shock: ±10%

PRODUCT MANUAL

max

6

®

TM

PRODUCT MANUAL

3. Mounting the SpotBot BLE

The SpotBot BLE comes with an integrated mounting plate at the bottom side. The mounting plate
provides four mounting holes for screw fastening purposes.

1 Screwdriver

2 Screw

FIGURE 2 I Mounting the SpotBot BLE Using Screws

In general, the SpotBot BLE can be mounted in any position as required. The fastening, depending on
the specic requirements, can be carried out with screws or with double-sided adhesive tape.

In the case shock will be measured, a direct and non-absorbing connection between the SpotBot BLE
and the monitored good is required. For achieving this we recommend using either screws or a ber
reinforced adhesive tape.

3 Mounting holes

3.1. Mounting with Screws

Recommended screws:

M5 or M4 (recommended with washer) raised cheese head / pan head / round head screws.

Recommended tightening torque: 1 Nm

3.2. Mounting with Adhesive Tape

Tape Specications: Double-sided ber-reinforced adhesive tape (tested with Tesa 56172-00003)

7