Bosch SHV570, SHE990 User Manual

YOUR LIFE. OUR INSPIRATION.

Dishwasher Installation instructions
instructions d'instaHation du _ave-vaisseIRe

Instrucciones de insta_aci6n para _avavajiHas

Use and Care Manua_ _ocated on reverse side
Tourner _e guide pour _eeinstructions d'utiHsation et d'entretien

Vo_tee e_ manua_ para encontrar _as instrucciones de uso y cuidado

9000063716 (8504)

Tabmeof Contents / Important hstructions

important Safety instructions

To avoid possible injury or property damage,

OBSERVE ALL WARNINGS AND CAUTIONS.

These instructions are intended for use by
qualified installers onty.

The dishwasher must be installed by a qualified
serqce technician.

o in addition to these instructions, the dishwasher

shah be installed to meet aHeUectrbaUand

pUumbingcodes and ordinances (both nationaUand
bcaU).

Read these installation instructions completely
and follow them carefully. They will save you time
and effort and help to ensure safety and optimum

If the dishwasher is installed in a Jocation that

experiences freezing temperatures (e.g., in a

holiday home), you must drain aH the water

from the dishwasher's interior. Water system

ruptures that occur as a result of freezing are
not covered by warranty.

IMPORTANT

* The dishwasherdrain hose must be installed

with a portion of it at least 20" (508mm) off the
cabinet floor; otherwise the dishwasher may not
drain properly.

* This dishwasher is intended for residential use

only, and should not be used in commercial food
service establishments.

o NEW INSTALLATION - If the dishwasher is a

new installation, most of the work must be done
before the dishwasher is moved into place.

* REPLACEMENT - If the dishwasher is replacing

another dishwasher, check the existing
dishwasher connections for compatibility with
the new dishwasher, and replace parts as
necessary.

* This appliance has been found to be in

compliance with CAN/CSA-C22.2 No. 167/UL

749. It is the responsibility of the owner and the
installer to determine if additional requirements
and standards apply in specific installations.

Inspect the Dishwasher
After unpacking the dishwasher and prior to
installation, thoroughly inspect the dishwasher for
possible freight or cosmetic damage. Report any
damage immediately. Cosmetic defects must be
reported within 5 days of installation.
NOTE: Do not discard any bags or items that come
with the original package until after the entire
installation has been completed,

TOOLS NEEDED

Tools and Materials Needed

Hammer

Tape Measu re

Wire Cutter

Hob Saw Adjustabb Wrench

Sbt Screwdriver

Wire Stripper

PhHHpsScrewdriver

MATERIALS NEEDED

(Additional materiab may be required to comply with bcal codes,)

DrHI _- Z i

%20 Screwdriver

Level

Ebctrbal Supply CaNe - Minimum #14 AWG, 2 conductor, 1 ground, insulated copper

conductors rated 75°C or higher,

_> Hot Water Supply Line - Minimum 3/8" O,D, copper tubing or metal braided dishwasher

......"_*s{_: .......supply line,

5 @}s Shut-off valve and fittings appropriate for hot water supply line (copper tubing/

compression fitting, or braided hose),

90° elbow with 3/8" N,P,T, male threads on one leg, and sized to fit your water supply

<c_...........;._",_> line (copper tubing/compression fitting, or braided hose) on the other leg,

:_;: Teflon tape or other pipe thread compound to seal plumbing connections,

UL listed conduit connector or strain relief,

2

Materials Supplied

MATERIALS SUPPUED

Accessory Parts Supplied
Accessory parts for your dishwasher come in one or more pUasticbags that are outlined bebw.

NOTE: Make sure you save aHthe bags until you have compbted your installation.
NOTE: Always use the suppibd or recommended hardware.

f Manual Set Bag

A ManuaUSet Bag is provided with each dishwasher and

includes:

A Use & Care instructions and installation

instructions (both manuab may be included

,nasingb"flip-styb'book

B Quick Reference Guide (sebct modeb)
C ExtraTaH item SpdnHer

D SHUand SHV installation Template (SHI and SHV _

models only)

E White Cotton Insulation Strip (SHY66C, SHX99A,

SH E66C, SH E99C, SHX57C and SHV57C models

f" Dishwasher Installation Kit

A Dishwasher Installation Kit is provided with each
dishwasher and includes:

F Toe Panel Screws (2 black machine screws)

Note: These screws are included, but not used on

models with the Toe Panel Installation Kit.

G Counter Top Mounting Brackets (2 '%"shaped metal

brackets)
H Mounting Bracket Screws (2 silver wood screws)
1 Rubber Drain Hose Adaptor (1 Mack rubber tube)

J Hose Clamps ( 1 silver spring clamp to use to

attach the rubber adaptor to the Drain Hose and 1

gold screw clamp to attach the rubber adaptor to

@--

; r

K Wire Nuts (3 for electrical connection)
L Electrical Junction Box Screws (2 silver

M Leg Leveler Locking Screws (2 gold coarse

!h sad screws!

f SHI/SHV Door Panel Installation Kit

A Door Panel Installation Kit is provided with select
dishwashers that use a custom wood door panel and

includes:

N Plastic Caps (2)
0 Spring Tension Screws (2 larger silver machine

screws used to adjust the door springs to accom-

modate doors of different weights)
P Door Mounting Brackets (2 gold metal brackets

and 2 white plastic brackets used to mount the

custom door)
Q Door Mounting Bracket Screws (8 silver wood

screws)

R Door Mounting Screws (2 long silver screws used

f Toe Panel Installation Kit

A Toe Panel Installation Kit is provided on models

SHY66C, SHX99A, SHE66C, SHE99C, SHX57C, and
SHV57C. These models have a special noise reducing

Toe Panel with the following mounting hardware:

S Toe Panel Screws (2 black screws used to attach

£_5559

@@ @,@

B

T Black Plastic Base Access Panel Screws (2 long

silver screws used to attach the Black plastic

Base AccessPans!!o!he d!shwasher: _J

3

23-9/I 6"

I_(598mm)

I"

EncBosure Preparation

ElectricaJ Shock Hazard

To avoid eJectricaJ shock, make sure the water
supply and electrical suppJy are shut off before

installation or service.

clearance

between

dishwasher
Check --I

door and wall

(89z}mrn)

mIR_mum

v I

23-5/8" - 24-1/4" (600-616

Figure 1

Figure 2

rY_f]q

Countertop

i\
i \

\

I

\

ENCLOSURE PREPARATmON

NOTE: This dishwasher is designed to be enclosed on the
top and both sides by standard residentiaU kitchen
cabinetry.

Select a location as close to the sink as possible for
easy access to water supply and drain lines.
For proper dishwasher operation and appearance, ensure
that the enclosure is square and has the dimensions
shown in Figure !.
if the dishwasher is to be installed in a corner, make sure
that there is adequate clearance to open the door. See
Figure 2,

ElectricaJ Shock/Fire Hazard

To avoid eJectric shock or fire, do not allow the
eJectricaJ and water supply Jines to touch.

Separate channeJs are provided under the
dishwasher (see page 10).

If the enclosure requires openings for the electrical supply
cable, hot water supply line, and dishwasher drain hose,
place them within the dimensions shown by the shaded
area of Figure 3 to avoid interference with the dishwasher
frame or other components. Make the openings for the
electrical supply cable and hot water supply line 1"
(25.4mm) diameter. Make the opening for the dishwasher
drain hose 1-1/4" (32mm) diameter. If the openings are
made through wood, sand them smooth. If the openings
are made through metal, make them large enough to
accommodate grommets or other protective sheaths with
inside diameters of 1" (25.4mm) for the electrical supply
cable and the hot water supply line, and 1-1/4" (32mm) for

the dishwasher drain hose.

Figure 3

4

30 _E

(762mm)

21 EE

(533mm)

Figure 4

Dishwasher E_ectrica_ Rating

Velts Amperes Watts

Electrical Shock Hazard

To avoid electdcaJ shock, do not work on an
energized circuit. Doing so could resuJt in serious
injury or death. Onty qualified electricians should
perform electrical work. Do not attempt any work
on the dishwasher etectric suppty circuit until you

are certain the circuit is
de-energized.

Fire Hazard

To avoid a fire hazard, make sure electrical work
is properly installed. OnJy qualified electricians
shouJd perform eJectrical work.

120 60 15 1,450

(max)

3" A,, 1

( 75mm ° lOOmm1.

3/8"- 1/2" _ .<

( 8mm- 13mm) I

Figure 5

Electrica! Supply
The customer has the responsibility of ensuring that the
dishwasher electrical installation is in compliance with all

national and local electrical codes and ordinances. The
dishwasher is designed for an electrical supply of 120V,

60 Hz, AC, connected to a dishwasher-dedicated,
properly grounded electrical circuit with a fuse or breaker
rated for 15 amps. Electrical supply conductors shall be a
minimum #14 AWG copper wire rated at 75°C or higher.

Regardless of where the electrical supply cable enters the
enclosure, position the cable 21" (533mm) from the
enclosure's left side, as shown in Figure 4. Extend the
cable 30" (762mm) from the enclosure's back, as shown
in Figure 4.

Remove 3" =4" (75mm =lOOmm) of the cable's outer
casing, as shown in Figure 5, then remove 3/8" - 1/2"
(9 - 13mm) of insulation from each wire, as shown in
Figure 5.

i355mm)

Hot Water

Supply

Line

Plumbing Preparation

PLUMBING PREPARATmON

Scald Hazard

To avoid being scaJded, do not perform any work
on a charged hot water tine. Serious injury could
result. Only qualified plumbers should perform
pJumbing work. Do not attempt any work on the
dishwasher hot water supply pJumbing until you
are certain the hot water supply is shut off.

Figure 6

Temperatures required for so(dedng and sweating
wil( damage the dishwasher's base and water inJet
va(ve. If plumbing lines are to be eo)dered or
sweated, keep the heat source at Jeast 6 inches
(152.4 ram) away from the dishwasher's base and

water in(et vaJve.

Hot Water Supply
The hot water heater should be set to deliver

approximately 120° F (49° C) water to the dishwasher,
Water that is too hot can cause some detergents to lose
effectiveness, Lower water temperatures will increase run
times, The hot water supply pressure must be between
15 - 145 psi (1 - 10 bars),

Hot Water Supply Plumbing
Install an easily accessible shut-off valve (not supplied) in
the hot water supply line, as shown in Figure 6, All solder

connections must be made before the water line is
connected to the dishwasher's water inlet valve, Water

may abe be supplied to the dishwasher by using a
stainless steel braided hose approved for dishwasher use,
Check with your local plumbing supply sources for the
proper hose and 90° elbow fitting,

NOTE: Regardless of where the hot water supply line
enters the enclosure, position the line 14" (355mm) from
the enclosure's left side, as shown in Figure 6,

NOTE: Decide whether braided hose or copper tubing wiii
be used for the hot water supply plumbing, and purchase
the correct type of hot water supply shut-off valve, 90°
elbow, and necessary fittings for the hot water supply

6