Bosch RFMS.ZBMS Installation Manual
en Installation Guide
fr Guide de l’installateur
RADION
Multi-Sensor ZB
RFMS-ZBMS
© 2017 Bosch Security Systems, Inc.
F.01U.330.367 | 00b | 2017.02
Bosch Security Systems, Inc.
130 Perinton Parkway
Fairport, NY 14450
USA
www.boschsecurity.com
Bosch Sicherheitssysteme GmbH
Robert-Bosch-Ring 5
85630 Grasbrunn
Germany
Copyright
This document is the intellectual property of Bosch Security Systems, Inc. and is protected by copyright. All rights reserved.
Trademarks
All hardware and software product names used in this document are likely to be registered trademarks and must be treated
accordingly.
Bosch Security Systems, Inc. product manufacturing dates
Use the serial number located on the product label and refer to the Bosch Security Systems, Inc. website at
http://www.boschsecurity.com/datecodes/.
FCC
This device complies with part 15 of the FCC
Rules. Operation is subject to the following two
conditions:
(1) This device may not cause harmful interference,
and (2) this device must accept any interference
received, including interference that may cause
undesired operation.
This equipment has been tested and found to
comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection
against harmful interference in a residential
installation. This equipment generates, uses
and can radiate radio frequency energy and, if
not installed and used in accordance with the
instructions, may cause harmful interference
to radio communications. However, there is no
guarantee that interference will not occur in a
particular installation.
If this equipment does cause harmful interference
to radio or television reception, which can be
determined by turning the equipment off and
on, the user is encouraged to try to correct the
interference by one or more of the following
measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment
and receiver.
– Connect the equipment into an outlet on a
circuit different from that to which the receiver is
connected.
– Consult the dealer or an experienced radio/TV
technician for help.
IC
Under Industry Canada regulations, this radio
transmitter may only operate using an antenna of a
type and maximum (or lesser) gain approved for the
transmitter by Industry Canada.
To reduce potential radio interference to other
users, the antenna type and its gain should be so
chosen that the equivalent isotropically radiated
power (e.i.r.p.) is not more than that necessary for
successful communication.
Le présent appareil est conforme aux CNR
d’Industrie Canada applicables aux appareils radio
exempts de licence. L’exploitation est autorisée
aux deux conditions suivantes : (1) l’appareil ne
doit pas produire de brouillage, et (2) l’utilisateur
de l’appareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage est
susceptible d’en compromettre le fonctionnement.
Conformément à la réglementation d’Industrie
Canada, le présent émetteur radio peut fonctionner
avec une antenne d’un type et d’un gain maximal
(ou inférieur) approuvé pour l’émetteur par
Industrie Canada.
Dans le but de réduire les risques de brouillage
radioélectrique à l’intention des autres utilisateurs,
il faut choisir le type d’antenne et son gain de sorte
que la puissance isotrope rayonnée équivalente
(p.i.r.e.) ne dépasse pas l’intensité nécessaire à
l’établissement d’une communication satisfaisante.
9 | Certifications
Agency Certification
Control No.3170792
Conforms to ANSI/UL Std. 634
ULC/ORD-C634-86
FCC FCC ID: T3X-012
IC IC ID: 1249A-012
This ZigBee® Certified product works in global 2.4 GHz networks supporting
ZigBee HA 1.2.1. ZigBee® Certified is a registered trademark of the ZigBee
Alliance.
ZigBee Cert No.xxx
Frequency (operating) 2.4 GHz
Max Power transmitted 20 dBm
Battery replacement
(1 per detector)
3 VDC
≥ 750mAh
Energizer CR2 Lithium
Duracell Ultra CR2 Lithium
Panasonic CR2 Lithium
Sanyo CR2 Lithium
Battery life
≥ 5 years with 16 open/close alarm events per day (door window
detector),
≥ 6 years (water detector), TBD (tilt detector)
Dimensions (detector) 1.8 in. x 0.92 in. x 0.79 in.
(46.0 mm x 23.5 mm x 20.3 mm)
Dimensions (magnet) 1.8 in. x 0.32 in. x 0.79 in.
(46.0 mm x 8.3 mm x 20.3 mm)
Temperature (operating) -4°F to +122°F
(-20°C to +50°C)
Storage temperature 14°F to +131°F
(-10°C to +55°C)
Relative humidity 5% to 93% at +32°C (+90°F)
Magnet gap break
distance
≥ 1.3 in. (33 mm) mounted to metal, vinyl, or wood
8 | Specifications
PRELIMINARY
Bosch Security Systems, Inc. | 2
The detector requires 1 batter y to
operate, which is pre-installed in the
detector.
1. Pull the tab from the back of the
detector to activate the battery. The
detector powers up, and the green
LED lights. The detector enters
pairing mode when the green LED
begins flashing 3 times every 5
seconds. Continue with Section 4.2,
Pairing process.
2. If you are installing a:
• Door Window Detector, continue
with Section 4.2, Pairing process.
• Water or Tilt Detector, continue with
Section 4.1, Configuring the detector
type.
Figure 4.1: Water Detector orientation
NOTICE!
Configure the detector type,
within the allotted time
before beginning pairing with
a home control system or
security control panel.
Changing the detector type to Water
Detector:
1. Move the magnet at least 1 ft (30.5
cm) away from the detector.
2. Push and hold the tamper switch, and
reinsert the battery. When the green
LED turns on, release the tamper
switch before the LED turns off (within
4 seconds).
By default, the detector type is a surfacemount detector for monitoring door or
window position (open or closed). You
can change the detector to operate as a
Water Detector or a Tilt Detector.
3. Place the detector horizontally on the
floor as shown in Figure 4.1.
4. Tap the detector 3 times within 30
seconds of powering the detector. The
green LED flashes 2 times to indicate
Water Detector.
5. Place the detector on the horizontal
surface of the area to monitor for water.
Refer to Figure 4.1.
Figure 4.2: Tilt Detector orientation
Test the proper operation of the Tilt
Detector:
1. Go to Section 4.2 and perform the
pairing process.
2. When finished pairing, move the
surface with the mounted detector to
a horizontal position. The green LED
turns on to indicate a tilted or open
position.
3. The green LED turns off after the test
is complete.
4.1.3 | Test Tilt Detector
Changing the detector type to Tilt
Detector:
1. Move the magnet at least 1 ft (305 mm)
away from the detector.
2. Push and hold the tamper switch, and
reinsert the battery. When the green
LED turns on, release the tamper
switch before the LED turns off (within
4 seconds).
3. Orient the detector vertically with the
alignment marker facing left.
4. Tap the detector 3 times within 30
seconds of powering the detector. The
green LED flashes 3 times to indicate
Tilt Detector.
5. Mount the detector on the top section
of the moving surface with the
alignment mark facing left. Refer to
Figure 4.2.
4.1.2 | Tilt Detector
4.1.1 | Water Detector
4.1 |
Configuring the
detector type
4 |
Installation
NOTICE!
The Water Detector may be
damaged if submerged in water.
For installation and mounting
considerations, use a smart phone and
scan the following QR code:
Placeholder for QRC:
installation video
Figure 3.1: Door/window installation locations
–Suitable flat sur faces for installation include wood, metal, vinyl, glass, and painted surfaces.
–Installation on metal sur faces can affect the RF propagation pattern of the radio transceiver.
–Verify proper clearance with the latch of the window or door and the detector. Failure to do
so might make it difficult to access and open the detector for maintenance.
–Moving the home automation or security system may improve RF performance. In some
instances, installing another device, such as a repeater, might be required.
3 | I
nstallation considerations
The product box contains:
–2 detectors with installed batteries
–2 magnets
–2 mounting brackets
–2 tape strips for mounting brackets
–Installation instructions
2 |
Product contents
The RADION Multi-Sensor ZB is a surfacemount wireless detector for monitoring
door or window position (open or closed),
and impact. The ZigBee® compatible radio
allows connection to a security or home
automation system. The detector also
monitors temperature, and includes a
tamper cover. You can optionally configure
the multi-detector for use as a Water
Detector or Tilt Detector.
1 | Overview
PRELIMINARY
Loading...