Bosch NET8666UC/01, NET8666SUC/01, NET8066UC/01, NET8066SUC/01, NEM5666UC/01 Installation Guide

...

Cooktop

Installation Instructions

NEM5066UC, NEM5666UC, NET8066SUC, NET8666SUC, NET8066UC, NET8666UC, NETPO66SUC, NETP666SUC

I I ,,'_

" BOSCH

i: _ ,lij

• :_¢J

Invented for life

....j

,,,,,

iiiiiiiiiiiiiiiiiii...............................

i! i _ Iii II

2', .........................

P,"J',"'¢:..... , :,,,, '_j,,,,_p?,

11111111111111.......

,................. i ,"f,_

Table of Contents

Safety Definitions .......................................................... 2

IMPORTANT SAFETY INSTRUCTIONS ........................ 3

State of California Proposition 65 Warnings ................... 3

Appliance Handling Safety ................................................. 3

Safety Codes and Standards ............................................. 3

Electric Safety ....................................................................... 3

Related Equipment Safety .................................................. 3

Before You Begin ........................................................... 4

Tools and Parts Needed ..................................................... 4

Parts Included ....................................................................... 4

Cabinet Requirements ......................................................... 4

Countertop Requirements .................................................. 4

Safety Definitions

• , WARNING This indicates that death or serious injuries may

occur as a result of non-observance of this warning.

Prepare Installation Space ........................................... 5

Cutout dimensions for 30" cooktops ............................... 5

Cutout dimensions for 36" cooktops ............................... 5

Installation Procedure .................................................. 6

Secure cooktop to countertop ........................................... 6

Electrical Installation .................................................... 7

Electrical Requirements ...................................................... 7

Connect Electrical Supply .................................................. 7

Check the Installation .......................................................... 7

Technical Service .......................................................... 8

• , CAUTION This indicates that minor or moderate injuries may

occur as a result of non-observance of this warning.

NOTICE: This indicates that damage to the appliance or property may occur as a result of non-compliance with this advisory.

Note: This alerts you to important information and/or tips.

IMPORTANT SAFETY INSTRUCTIONS

READ AND SAVE THESE INSTRUCTIONS

IMPORTANT - SAVE THESE INSTRUCTIONS FOR THE LOCAL ELECTRICAL INSPECTOR'S USE.

LEAVE THESE INSTRUCTIONS WITH THE APPLIANCE AFTER INSTALLATION IS COMPLETE.

WARNING

If the information in this manual is not followed exactly, fire or shock may result causing property damage or

personal injury.

WARNING

Do not repair, replace or remove any part of the appliance unless specifically recommended in the manuals. Improper installation, service or maintenance can cause injury or property damage. Refer to this manual for guidance. All other servicing should be done by a qualified technician.

State of California Proposition 65 Warnings

WARNING

This product contains chemicals known to the State of

California to cause cancer, birth defects or other reproductive harm.

Appliance Handling Safety

Hidden surfaces may have sharp edges. Use caution when reaching behind or under appliance.

Safety Codes and Standards

This appliance complies with the latest version of one or

more of the following standards: o UL 858- Household Electric Ranges o CAN/CSA-E335-1/3E-94 - Safety of Household and

Similar Electrical Appliances - General

o CAN/CSA-E60335-2-6-01 - Safety of Household and

Similar Electric Appliances - and particular requirements for stationary cooking ranges, hobs, ovens and similar appliances.

It is the responsibility of the owner and the installer to

determine if additional requirements and/or standards apply to specific installations.

Electric Safety

WARNING

Before you plug in an electrical cord or turn on power

supply, make sure all controls are in the OFF position.

If required by the National Electrical Code (or Canadian Electrical Code), this appliance must be installed on a

separate branch circuit. The circuit breaker should have a contact separation of

at least 3 mm on all poles.

Be sure your appliance is properly installed and grounded by a qualified technician. Installation, electrical connections and grounding must comply with all applicable codes.

Before installing, turn power OFF at the service panel.

Lock service panel to prevent power from being turned ON accidentally.

Installer - show the owner the location of the circuit

breaker or fuse. Mark it for easy reference.

Related Equipment Safety

The appliance is only guaranteed safe to use if installed

by a specialist in accordance with these installation

instructions. The installer is liable for any damage

resulting from incorrect installation.

Remove all tape and packaging before using the appliance. Destroy the packaging after unpacking the appliance. Never allow children to play with packaging

material.

Never modify or alter the construction of the appliance. To eliminate the risk of burns or fire by reaching over

heated surface units, cabinet storage space located above the surface units should be avoided. If cabinet

storage is to be provided, the risk can be reduced by

installing a hood that projects horizontally a minimum of

5 inches (127 mm) beyond the bottom of the cabinet. Verify that cabinets above the cooktop are a maximum of

13" (330 mm) deep.

Do not install refrigerators, dishwasher, non-fan-assisted ovens or washing machines which fit underneath the

cooktop.

Note: We strongly recommend the installation of a ventilation system with this appliance.

Before You Begin

Tools and Parts Needed

o Phillips Head Screwdriver o Pencil

o Drill with 1/2'(6 mm) bit o Jigsaw o Tape Measure

Note: Additional materials may be necessary for installation in solid surface countertops. Contact the countertop manufacturer.

Parts Included

Cabinet Requirements

The distance from the top of the cooktop to the bottom of

cabinets above must be a minimung of A=30 '' (762 mm)

min. This distance can be reduced to A=24 '' (610 mm)

when the bottom of the wood or metal cabinet is

protected by not less than 1/2'(6.35 mm) flame-retardant

millboard covered with not less than no. 28 gauge sheet

metal, 0.015" (0.4 mm) stainless steel, 0.024" (0.6 mm)

aluminum or 0.020" (0.5 mm) copper.

Verify that the cabinets above the cooktop are a

maximum of B=I 3" (330 mm) deep.

Countertop Requirements

• , WARNING To reduce the risk of ignition of surrounding

combustible materials, install at least 2" (51 mm)

from both sidewalls and the rear wall.

The countertop must be level and horizontal. The stability of the countertop must be maintained after the cut-out

has been made. Solid surface countertops often require special

installations. For example, heat-reflective tape and rounded corners may be necessary. Contact the countertop manufacturer for instructions specific to your countertop.

::, _: __;_;_: _ ;; ;__: _..........................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................

Prepare Installation Space

Create the cut-out in the countertop according to the installation diagram. The angle of the cut surface to the countertop must be 90 °.

The lateral cut-out edges must be flat in order to ensure that the retaining springs are well-positioned on the appliance. With multi-layered countertops, secure strips laterally in the cut-out if necessary.

After creating cut-out, remove shavings. Seal cut surfaces in a heat- and water-resistant manner.

Observe minimum distance between device underside and furniture parts of 3/s" (10 mm).

Cutout dimensions for 30" cooktops

Models: NEM5066UC, NET8066SUC, NET8066UC, NETP066SUC

I I

min. 30" (762 mm)

min. 2" min. 2"

Cutout dimensions for 36" cooktops

Models: NEM5666UC, NET8666SUC, NET8666UC, NETP666SUC

I I

min. 30" (762 mm)

min. 2" ,l min. 2"

(6mm) ---_

min. 2" (51 mm)

min. 2 1/4" (57mm)

(6mm) --_

min. 2" (51ram)

min. 2 1/4" (57mm)

(5(_5'-' 50__83/! ;8347/8"

Installation Procedure

CAUTION

Sharp edges. Use protective gloves when installing the cooktop.

Secure cooktop to countertop

The cooktop should be secured to the countertop using the clamps provided.

1. Prior to inserting cooktop into cutout, attach clamps to the corresponding slots.

Models: NEM5066UC, NET8066SUC, NET8066UC

3. Insert clamping screws into the bracket and secure

cooktop to countertop. Use a wood block to protect fragile countertop materials.

Models: NEM5066UC, NET8066SUC, NET8066UC

Models: NEM5666UC, NET8666SUC, NET8666UC, NETP666SUC, NETP066SUC

2. Place cooktop into cutout.

Electrical Installation

Electrical Requirements

You can find the identification plate with the electrical specifications on the underside of the appliance. The junctionbox must be located within 3 feet of the cooktop connection. It should be easily accessible for service

purposes.

4" (100 mm) + Fitting/Conduit 0.9" (23 mm)

12" (300mm)Approximate

"J"box

Conduit approx. 3 feet (~900mm)

Power supply

Model 240 V AC, 60 Hz 208 V AC, 60 Hz

system: circuit system: circuit breaker breaker

NETP666SUC 40 Amp 40 Amp NETP066SUC 40 Amp 40 Amp

NET8666UC 40 Amp 40 Amp NET8066UC 40 Amp 30 Amp

NET8666SUC 40 Amp 40 Amp NET8066SUC 40 Amp 30 Amp

NEM5666UC 40 Amp 40 Amp NEM5066UC 30 Amp 30 Amp

Connect Electrical Supply

• , WARNING Before installing, turn off at the service panel. Lock

service panel to prevent power from being turned on accidentally.

The electrical power supply system should be a 1-phase, 3-wire system with ground connection. Install suitable junction box (not furnished). An appropriately-sized, UL- listed conduit connector must be used to correctly attach the conduit to the junction box.

The branch-circuit breakers ampacity, the wire sizes and the connections must be conform to the requirements of

the National Electrical Code or Canadian Electrical Code and all local codes and ordinances.

Attach flexible conduit to the junction box.

• , WARNING

To reduce the risk of electric shock and fire, do not

use a flexible power supply cord.

Connect the cooktop lead wires to the junction box supply wires in proper phase:

black (L1) to black red (L2) to red

blank copper wire to ground

Check the Installation

• , CAUTION Before you plug in an electrical cord or turn on

power supply, make sure all controls are in the OFF position.

Remove everything from the cooktop surface including

stickers. Clean cooktop surface with cooktop cleaning creme.

Switch on the circuit breaker. Verify that elements function properly.

+ 16 hidden pages