Bosch MIC-WMB-WD, MIC-WMB-BD, MIC-SPR-BD, MIC-SCA-WD, MIC-SCA-BD Specsheet

Video | MIC Mounting Brackets and Other Accessories

MIC Mounting Brackets and Other
Accessories

www.boschsecurity.com

u Full range of mounting brackets and other

accessories.

Bosch Security Systems offers a range of mounting
brackets and accessory products for the MIC family of
cameras. The mounting brackets (for corner, wall, and
pole mounting) are available in the standard colors of
the MIC family. (Note: Not all colors of mounting
brackets are available for all models of MIC cameras.)
The accessories have been designed to work
seamlessly with MIC cameras to extend their
functionality for your application. This datasheet
provides an overview of the available MIC accessories.
The following accessories have their own datasheets:

• MIC illuminators (for MIC IP camera models)

• MIC Alarm/Washer Interface (MIC-ALM-WAS-24)

• High PoE Midspan models

• VG4-A-PSU series

• VIDEOJET connect 7000 (VJC-7000-90)

The Serial Protocol Software License (MVS-FCOM­PRCL), an e-license key for serial protocol for MIC IP
cameras, is also available.

u Designed to integrate seamlessly with the MIC

family.

u Provides a best-fit solution for virtually any

application.

u Easy to use and install.

u Accessories extend functionality.

System overview

Mounting Accessories

Deep Conduit Adapter

The MIC Deep Conduit Adapter (DCA) is designed to
allow a weatherproof conduit or cable gland to be
fitted to protect the signal cables. The DCA provides a
convenient mounting point for a MIC IP camera.
The hinge feature allows installers to “hang” the
camera temporarily but securely during installation for
easier connection of cables/wiring before final bolts
are installed.
The DCA has two M25 holes, one in the base and one
in the side.
An O-ring seals the camera-to-mount interface to an
ingress rating of IP68.
Supplied hardware includes:

• Four (4) M8 x 20 stainless steel hex bolts

• Four (4) M8 stainless steel plain washers

• One (1) O-ring, 80 mm x 3 mm

• One (1) end cap/blanking plug, M25 x 1.5, with O-ring

Certain models (MIC-DCA-HxA) also include:

• One (1) conduit adapter (male M25 to female 3/4"
NPT)

564 mm
(23.4 in.)

120 mm
(4.7 in.)

| MIC Mounting Brackets and Other Accessories

2

Wall Mount Bracket

The MIC Wall Mount Bracket (MIC-WMB) allows
mounting on building walls. It also coordinates with a
MIC Pole Mount Bracket (MIC-PMB) and a MIC
Shallow Conduit Adapter (MIC-SCA) to allow mounting
a MIC camera on a lamp post, scaffolding, or other
non-standard mounting post. The MIC-WMB has a
deep bowl to accommodate the signal cable
connections.
An O-ring seals the camera-to-mount interface to an
ingress rating of IP68.

Supplied hardware includes:

• Four (4) M8 x 30 stainless steel cap head bolts

• Six (6) M6 x 20 stainless steel countersunk head
bolts

• Two (2) high-torque stainless steel worm drive clips
(banding straps), 1 m long

• Two (2) pole mount blocks

• One (1) mounting plate

Corner Mount Bracket

The MIC Corner Mount Bracket (MIC-CMB)
coordinates with a MIC-SCA and a MIC-WMB to allow
mounting a MIC camera on the corner of a building.

Supplied hardware includes:

• Four (4) M8 x 20 stainless steel hex bolts

• Four (4) M8 stainless steel plain washers

• One (1) O-ring, 80 mm x 3 mm

Pole Mount Bracket

The MIC Pole Mount Bracket (MIC-PMB) coordinates
with a MIC-SCA and a MIC-WMB to allow mounting a
MIC camera on a lamp post, scaffolding, or other non­standard mounting post. The MIC-PMB accommodates
a wide range of diameters.

Supplied hardware includes:

• Four (4) M8 x 25 stainless steel hex bolts

• Four (4) M8 stainless steel plain washers

• Four (4) M8 stainless steel nuts

Spreader Plate

The MIC Spreader Plate (MIC-SPR) is used to spread
the weight of a MIC camera and its supporting
brackets so that the camera can be mounted securely
to a flat masonry surface.

ø 9 mm
(23.4 in.)

190 mm square

(7.5 in.)

12.7 mm
(0.5 in.)

| MIC Mounting Brackets and Other Accessories

3

Supplied hardware includes:

• Four (4) M8 x 30 stainless steel cap head bolts

• Four (4) M8 stainless steel plain washers

• Four (4) M8 stainless steel nuts

Shallow Conduit Adapter

The MIC Shallow Conduit Adapter (MIC-SCA) is used
as required with other mounting brackets. The MIC­SCA has a single M25 side entry conduit fitting hole.
There is not sufficient room inside to allow the camera
to be mounted to it directly. (Use a MIC-DCA-Hx or a
MIC-DCA instead.)
An O-ring seals the camera-to-mount interface to an
ingress rating of IP68.

Sunshield Kits

Sunshield Kits are available for various MIC cameras.
Each kit is designed to provide additional protection
for the camera from direct solar radiation, particularly
in sunny climates, by reflecting solar exposure, and by
creating an insulating gap between the environment
and the surface of the camera.

Sunshield Kit for MIC IP fusion 9000i cameras

The Sunshield Kit for MIC IP fusion 9000i cameras
(MIC-9K-SNSHLD-W) includes two (2) white, molded
shells that attach to the tilt head of the camera.

Supplied hardware includes:

• Four (4) M8 x 20 stainless steel hex bolts

• Four (4) M8 stainless steel plain washers

• One (1) O-ring, 80 mm x 3 mm

• One (1) end cap/blanking plug, M25 x 1.5, with O-ring

Other Hardware Accessories

M25 to 3/4"NPT Thread Adapter (MIC­M25XNPT34)

The conduit adapter (male M25 to female 3/4" NPT)
(MIC-M25XNPT34) allows attachment of ¾” NPT
conduit that is popular in the North American region to
MIC-DCA-Hx, MIC-DCA, and MIC-SCA mounts that have
M25x1.5 threaded holes. This adapter is included with
the following DCA models: MIC-DCA-HBA, MIC-DCA­HWA, and MIC-DCA-HGA. The adapter is manufactured
from 316 stainless steel and includes a silicone O-ring
that seals the adapter to the conduit adapter to an
ingress rating of IP68.

Supplied hardware includes:

• Four (4) M4 x 8 stainless steel socket head Torx
screws

• Four (4) M4 stainless steel flat washers

Sunshield for MIC IP ultra 7100i and MIC IP
starlight 7100i

The one-piece sunshield (MIC-7100I-SNSHLD-W)
attaches to the head of MIC IP ultra 7100i and MIC IP
starlight 7100i cameras.
The sunshield has a section that installers can cut out,
before installation, to make space to install a MIC
illuminator.

Supplied hardware includes:

• Two (2) M4 x 8 Torx screws, of stainless steel, with
socket heads

MIC-SPR-BD,

-WD, -MG

MIC-SCA-BD,

-WD, -MG
MIC-WMB-BD,

-WD, -MG

MIC-WMB-BD,

-WD, -MG

MIC-SCA-BD,

-WD, -MG

MIC-PMB

MIC-CMB-BD,

-WD, -MG

MIC-SCA-BD,

-WD, -MG
MIC-WMB-BD,

-WD, -MG

MIC-DCA-HB,

-HW, -HG

MIC-7130,
MIC-7230

4 | MIC Mounting Brackets and Other Accessories

Washer Kit

The MIC washer kit (MIC-WKT-IR) connects a washer
pump and water reservoir tank to a MIC camera.
Supplied hardware includes:

• One (1) washer jet nozzle

• Two (2) mounting brackets for the washer jet nozzle

Certifications and approvals

Region Regulatory compliance/quality marks

Europe CE - MIC-9K-IP67-5PK

Installation/configuration notes

Typical Mounting Arrangement, Wall mount

Typical Mounting Arrangement, Corner mount

Typical Corner mount configuration

Not shown: Mounting hardware.

Typical Mounting Arrangement, hinged DCA

Typical Wall mount configuration

Not shown: Mounting hardware.

Typical Mounting Arrangement, Pole mount

Typical Pole mount configuration

Not shown: Mounting hardware.

Typical hinged DCA mount configuration

Technical specifications

MIC Hinged DCA

Dimensions
(H x W)

Weight 2.5 kg (5.5 lb)

Material solid aluminum with painted polyester finish as below

MIC-DCA-HB Black (RAL 9005), sand finish

MIC-DCA-HW White (RAL 9010), sand finish

MIC-DCA-HG Grey (RAL 9006), sand finish

120 x 131.6 mm
(4.7 x 5.18 in.)

(Available in specific regions only.)

MIC-DCA-HBA Black (RAL 9005), sand finish

5 | MIC Mounting Brackets and Other Accessories

MIC-DCA-

HWA

MIC-DCA-HGA Grey (RAL 9006), sand finish

MIC Wall Mount Bracket

Dimensions
(W x H x D)

Weight 1.95 kg (4.5 lb)

Material solid aluminum with painted polyester finish as below:

MIC-WMB-BD Black (RAL 9005), sand finish

MIC-WMB-WD White (RAL 9010) , sand finish

MIC-WMB-MG Grey (RAL 7001), sand finish

MIC Pole Mount Bracket (MIC-PMB)

Dimensions
(W x H x D)

Weight 1.7 kg (3.75 lb)

Material Mounting bracket, mounting blocks: Aluminum

Finish color Clear anodized

340 x 124 x 120 mm
(13 x 5 x 4.7 in.)

127 x 160 x 9.5 mm (25.375 with pole mount blocks
fitted)
(5 x 6 x 0.4 in.)

Banding straps: Stainless steel

White (RAL 9010), sand finish

(Available in specific regions only.)

(Available in specific regions only.)

MIC Shallow Conduit Adapter

Dimensions
(H x D)

Weight 0.78 kg (1.7 lb)

Material solid aluminum with painted polyester finish as below:

MIC-SCA-BD Black (RAL 9005), sand finish

MIC-SCA-WD White (RAL 9010), sand finish

MIC-SCA-MG Grey (RAL 7001), sand finish

Sunshield for MIC IP fusion 9000i thermal cameras (MIC-9K-SNSHLD­W)

Dimensions
(W x H x D)

Weight 0.40 kg (14 oz)

40 x 120 mm
(1.6 x 4.7 in.)

(Available in specific regions only.)

150 x 232 x 110 mm (5.9 x 9.1 x 4.3 in.)

Sunshield for MIC IP ultra 7100i and MIC IP
starlight 7100i

Dimensions (L x W x H) 210 mm x 191 mm x 139 mm

(8.3 in. x 7.5 in. x 5.5 in.)

Weight 0.194 kg (0.4 lb)

Construction Material Plastic

Color White

MIC Corner Mount Bracket

Dimensions
(W x H x D)

Weight 2.9 kg (6.5 lb)

Material solid aluminum with painted polyester finish as below:

MIC-CMB-BD Black (RAL 9005), sand finish

MIC-CMB-WD White (RAL 9010), sand finish

MIC-CMB-MG Grey (RAL 7001), sand finish

MIC Spreader Plate

Dimensions
(W x H x D)

Weight 1.24 kg (2.7 lb)

Material solid aluminum with painted polyester finish as below:

MIC-SPR-BD Black (RAL 9005), sand finish

MIC-SPR-WD White (RAL 9010), sand finish

MIC-SPR-MG Grey (RAL 7001), sand finish

564 x 120 x 394 mm
(23 x 4.7 x 15.5 in.)

(Available in specific regions only.)

190 x 190 x 12.7 mm
(7.5 x 7.5 x 0.5 in.)

(Available in specific regions only.)

6 | MIC Mounting Brackets and Other Accessories

Ordering information

MIC-DCA-HB Deep conduit mount, M25 holes, black

DCA mount for MIC7000 and MIC IP fusion 9000i
cameras. Aluminum. Two M25 holes for conduit/cable
glands.
Black (RAL 9005) color.

Order number MIC-DCA-HB

MIC-DCA-HW Deep conduit mount, two M25 holes,
white

DCA mount for MIC7000 and MIC IP fusion 9000i
cameras. Aluminum. Two M25 holes for conduit/cable
glands.
White (RAL 9010) color.

Order number MIC-DCA-HW

MIC-DCA-HG Deep conduit mount, two M25 holes,
grey

DCA mount for MIC7000 and MIC IP fusion 9000i
cameras. Aluminum. Two M25 holes for conduit/cable
glands.
Grey (RAL 7001) color. Available in specific regions
only.

Order number MIC-DCA-HG

MIC-DCA-HBA Deep conduit mount, M25 holes, black

DCA mount for MIC7000 and MIC IP fusion 9000i
cameras. Aluminum. Two M25 holes for conduit/cable
glands. Includes an conduit adapter (male M25 to
female 3/4" NPT). Available in specific regions only.
Black (RAL 9005) color.

Order number MIC-DCA-HBA

MIC-DCA-HWA Deep conduit mount, M25 holes,white

DCA mount for MIC7000 and MIC IP fusion 9000i
cameras. Aluminum. Two M25 holes for conduit/cable
glands. Includes an conduit adapter (male M25 to
female 3/4" NPT). Available in specific regions only.
White (RAL 9010) color.

Order number MIC-DCA-HWA

MIC-DCA-HGA Deep conduit mount, M25 holes,grey

DCA mount for MIC7000 and MIC IP fusion 9000i
cameras. Aluminum. Two M25 holes for conduit/cable
glands. Includes an conduit adapter (male M25 to
female 3/4" NPT). Available in specific regions only.
Grey (RAL 7001) color.

Order number MIC-DCA-HGA

MIC-WMB-BD Wall mount bracket , black

Wall mount bracket, black sand finish (RAL9005)

Order number MIC-WMB-BD

MIC-WMB-WD Wall mount bracket, white

Wall mount bracket, white sand finish (RAL9010)

Order number MIC-WMB-WD

MIC-WMB-GD Wall mount bracket , grey sand

Wall mount bracket, Grey (RAL 9006), sand finish, for
MIC-612xxxxG36x series cameras

Order number MIC-WMB-GD

MIC-WMB-MG Wall mount for rugged PTZ camera,
grey

Wall Mount Bracket.
Grey (RAL 7001). Available in specific regions only.
Sand finish.

Order number MIC-WMB-MG

MIC-PMB Pole mount bracket

Pole mount bracket (includes 2 x 455 mm stainless
steel banding straps for pole diameters 75 to 145 mm)

Order number MIC-PMB

MIC-CMB-BD Corner mount bracket, black

Corner mount bracket, black sand finish (RAL9005)

Order number MIC-CMB-BD

MIC-CMB-WD Corner mount bracket, white

Corner mount bracket, white sand finish (RAL9010)

Order number MIC-CMB-WD

MIC-CMB-MG Corner mount bracket, grey sand

Corner mount bracket.
Grey (RAL 7001). Available in specific regions only.
Sand finish.

Order number MIC-CMB-MG

MIC-SPR-BD Wall mount spreader plate, black sand

Aluminum spreader plate suitable for brickwork
surface mounting, black sand finish (RAL9005)

Order number MIC-SPR-BD

MIC-SPR-WD Wall mount spreader plate, white sand

Aluminum spreader plate suitable for brickwork
surface mounting, white sand finish (RAL9010)

Order number MIC-SPR-WD

MIC-SPR-GD Wall mount spreader plate, grey sand

Aluminum spreader plate suitable for brickwork
surface mounting, grey sand finish (RAL 9006), for
MIC-612xxxxG36x series cameras

Order number MIC-SPR-GD

MIC-SPR-MG Wall mount spreader plate, grey sand

Aluminum spreader plate suitable for brickwork
surface mounting.
Grey (RAL 7001). Available in specific regions only.
Sand finish.

Order number MIC-SPR-MG

MIC-SCA-BD Shallow conduit adapter, black sand

Shallow conduit adapter for a MIC-WMB, a MIC-PMB,
or a MIC-SPR, black sand finish (RAL9005)

Order number MIC-SCA-BD

MIC-SCA-WD Shallow conduit adapter, white sand

Shallow conduit adapter for a MIC-WMB, a MIC-PMB,
or a MIC-SPR mount, white sand finish (RAL9010)

Order number MIC-SCA-WD

7 | MIC Mounting Brackets and Other Accessories

Represented by:

Europe, Middle East, Africa: Germany: North America: Asia-Pacific:

Bosch Security Systems B.V.
P.O. Box 80002
5600 JB Eindhoven, The Netherlands
Phone: + 31 40 2577 284
[e-mail]
emea.boschsecurity.com

Bosch Sicherheitssysteme GmbH
Robert-Bosch-Ring 5
85630 Grasbrunn
Germany
www.boschsecurity.com

Bosch Security Systems, Inc.
130 Perinton Parkway
Fairport, New York, 14450, USA
Phone: [phone]
Fax: [phone]
[e-mail]
www.boschsecurity.us

Robert Bosch (SEA) Pte Ltd, Security Systems
11 Bishan Street 21
Singapore 573943
Phone: [phone]
Fax: [phone]
[e-mail]
www.boschsecurity.asia

© Bosch Security Systems 2019 | Data subject to change without notice
2279980683 | en, V16, 06. Sep 2019

MIC-SCA-GD Shallow conduit adapter, grey sand

Shallow conduit adapter for a MIC-WMB, a MIC-PMB,
or a MIC-SPR, grey sand finish (RAL 9006), for
MIC-612xxxxD36x series

Order number MIC-SCA-GD

MIC-SCA-MG Conduit adapter, shallow, grey sand

Shallow conduit adapter for a MIC-WMB, a MIC-PMB,
or a MIC-SPR.
Grey (RAL 7001). Available in specific regions only.
Sand finish.

Order number MIC-SCA-MG

MIC-M25XNPT34 Adapter, M25 to 3/4"NPT, stainless
steel

Stainless Steel M25 to ¾” NPT thread adapter

Order number MIC-M25XNPT34

MIC-67SUNSHLD Sunshield for MIC7000 series, white

Three-part molded sunshield for MIC7000 cameras – 1
bottom shell, 2 top shells (1 for around the optional
illuminator accessory). White.

Order number MIC-67SUNSHLD

MIC-9K-SNSHLD-W Sunshield thermal PTZ camera,
white

Sunshield kit for MIC IP fusion 9000i cameras, white
color. Recommended for use with white color MIC IP
fusion 9000i cameras installed in locations with high
sun load.

Order number MIC-9K-SNSHLD-W

MIC-BP3 Biphase converter, for power supply

Biphase converter for IR power supplies or non-IR
power supplies without a free expansion slot available

Order number MIC-BP3

MIC-BP4 Biphase converter, for power supply

Biphase converter for non-IR versions of MIC series
power supply units

Order number MIC-BP4

MIC-ALM 8 input alarm card for MIC400 non IR PSU

8 Input alarm and washer pump drive card for PSU
(Not for IR PSU). Requires washer pump, purchase
separately.

Order number MIC-ALM

MIC-WKT Washer kit, MIC non IR

Washer kit for non-infrared MIC camera models.

Order number MIC-WKT

MIC-WKT-IR Washer kit, MIC IR

Washer kit for analog infrared MIC camera models as
well as for MIC IP starlight 7000i and MIC IP fusion
9000i camera models.

Order number MIC-WKT-IR