Bosch LTC 9312-00 User Manual

Instruction Manual

EN Indoor Dome

Housings

LTC 9312/00

EN|2

Bosch Security Systems | 28 July 2004

LTC 9312 | Instruction Manual | Important Safeguards

Important Safeguards

1. Read, Follow, and Retain Instructions - All safety
and operating instructions should be read and
followed before operating the unit. Retain instructions
for future reference.

2. Heed Warnings - Adhere to all warnings on the unit
and in the operating instructions.

3. Electrical Connections - Only a qualified electrician
should make electrical connections.

4. Cable Runs - All cable runs must be within
permissible distances.

5. Mounting - This unit must be properly and securely
mounted to a supporting structure capable of
sustaining the weight of the unit. Accordingly:
a. The installation should be made by a qualified

installer, in compliance with local codes.

b.Exercise care in selecting suitable hardware to

install the unit, taking into account both the
composition of the mounting surface and the
weight of the unit. Periodically examine the unit
and the supporting structure to ensure that the
integrity of the installation is intact.

Failure to comply with these stipulations may result in
separation from the support structure. This may cause
damages or injury to anyone or anything struck by the
falling unit.

6. Attachments - Attachments not recommended by
the product manufacturer should not be used, as they
may cause hazards.

EN|3

Bosch Security Systems | 28 July 2004

LTC 9312 Series | Instruction Manual | Unpacking

1UNPACKING

This mechanical equipment should be unpacked and
handled carefully.
Check for the following items:
Qty. Item
1LTC 9312/00
1 Clear dome
2 Support channels
1 Black opaque liner
1FM2 camera bracket assembly
1 Black dust cover

If an item appears to have been damaged in shipment,
replace it properly in its carton and notify the shipper.
If any items are missing, notify your Bosch Security
Systems Inc. Sales Representative or Customer Service.

The shipping carton is the safest container in which the
unit may be transported. Save it for possible future use.

2SERVICE

If the unit ever needs repair service, the customer
should contact the nearest Bosch Security Systems, Inc.
Service Center for return authorization and shipping
instructions.

Service Centers

USA

Phone: [phone] or 717-735-6638

fax: [phone] or 717-735-6639

CCTV Spare Parts

Phone: [phone] or 408-956-3853 or 3854

fax: [phone]

e-mail: [e-mail]

Canada

Phone: [phone]

Europe, Middle East & Asia Pacific Region

Phone: [phone]
For additional information, see
www

.boschsecuritysystems.com.

3INSTALLATIO N

1. Remove the contents from the box.

2. Remove the ceiling tile in the desired location.

3. Place the acrylic dome in the chosen location;
the dome will rest on the ceiling grid. (Be sure
the grid is adequately supported.)

4. Using a utility knife or scissors, carefully cut a
hole in the black opaque liner, for the camera
to view through.
NOTE: Smaller cutouts allow more discreet
viewing.

5. Place the black opaque liner into the acrylic
dome and rotate it to the desired viewing
position.

6. Align the long slots of two FM2 camera
bracket arms.

7. Using a carriage bolt, 5/16in. washer, 1/4in.
washer, lockwasher, and hex nut, attach the
bracket arms together loosely. See FIGURE 1.

8. Slide the smaller channel through the slot on
the larger support channel. See FIGURE 2.
Use the 1/4 x 20 bolt supplied to connect the
FM2 to the support channels (via the center
hole in the two channels). BE CAREFUL
WHEN HANDLING THE SUPPORT
CHANNELS; EDGES MAY BE SHARP.

9. Securing tabs are provided to hold the bracket
between the liner. Bend the corresponding tab
with a screwdriver.

10.Connect the camera to the FM2 bracket, and
place the assembly in the dome so the edges
of the bracket rest on the flange of the dome.

11. Tighten all connections and complete wiring
the camera.

12.A tex-wipe is provided to clean the dome.

13. Place the black dust cover over the top of the
dome, so the dust cover is sitting on the
supporting channels.

USE ONLY WITH A CLASS 2 POWER
SUPPLY.

For added flexibility, the camera can be mounted on
either the short or the long side of the bracket arm.

EN|4

LTC 9312 Series | Instruction Manual | Parts List

PARTS LIST

FIGURE 1

FIGURE 2

FIGURE 3

Part No. Qty. Description

1 90-BTCA01 2 1/4-20 x 3/4in. Zinc Carriage
2 30-VL696 1 4 in 1 Camera Bracket
3 92-WSSL01 2 1/4 Split Lockwasher 18-8 SS
491-NTHH02 2 1/4-20 Hex Nut 18-8 SS
5 30-VL732 1 0-1 Multiple Camera Bracket
6 92-WSFL05 1 5/16 Flat Washer SS
7 92-WSFL01 1 1/4 SAE Flat Washer 18-8 SS
8 90-BTHH11 2 1/4-20 x 1/2 Hex Head Zinc
9 96-RSORNG 1 -009 O-ring

© 2004 Bosch Security Systems GmbH

3935 890 15212 04-31 | Updated July 28, 2004 | Data subject to change without notice.

Bosch Security Systems, Inc.
850 Greenfield Road
Lancaster, PA 17601 USA
Tel: [phone]
Fax: [phone]
www.boschsecuritysystems.com

Bosch Security Systems B.V.
P.O. Box 80002
5600 JB Eindhoven
The Netherlands
Tele [phone]

Bosch Security Systems Pte Ltd.
38C Jalan Pemimpin
Singapore 577180
Republic of Singapore
Tel: [phone]