Bosch ICP-SDI-9114 Specsheet

Intrusion Alarm Systems | ICP-SDI-9114 SDI Splitter

ICP-SDI-9114 SDI Splitter

www.boschsecurity.com

u Provides two independent, isolated SDI buses from

a single SDI connection to the control panel

u Can be used to meet the requirements for a UL864

compliant combination control panel

The ICP-SDI-9114 SDI Splitter allows the set up of two
independent, isolated SDI buses from a single SDI
connection on the control panel. When this accessory
is installed with a control panel and wired to create
separate SDI buses for fire and intrusion devices, the
system is a UL864 compliant combination control
panel.

Notice

The B9512G, B9512G-E, B8512G, and B8512G-E
control panels can be used as combination
systems per UL864, 9th edition requirements.
When using only the SDIx bus programmed for
legacy SDI communication, the ICP‑SDI‑9114 SDI
Splitter will be required.

Notice

The D9412GV4, D9412GV3, D9412GV2,
D7412GV4, D7412GV3, and D7412GV2 control
panels can be installed as a combination system
per UL864, 9th edition requirements when used
with the ICP‑SDI‑9114 SDI Splitter.

Notice

The D7212GV4, D7212GV3, D7212GV2, and
D7212G are not rated for Commercial Fire.

u Does not affect the operation of the control panel or

the associated SDI devices

u Additional power can be supplied by an external

power supply

Functions

Connections

The SDI splitter has three sets of four‑position SDI
terminals: PANEL, FIRE, and BURG. The PANEL
terminals are used for the SDI connection to the
control panel. The terminals labeled FIRE and BURG
are handled equally, and either terminal can be
assigned to any collection of devices that require two
separate buses. The SDI splitter does not affect the
operation of the control panel or the associated SDI
devices.

LEDs

The SDI splitter has three green LEDs (labeled PANEL
ACTIVE, FIRE ACTIVE, and BURG ACTIVE) that monitor
bus activity.

Power

The SDI splitter operates on power from the control
panel, but the DC current is limited to 550 mA for each
bus (FIRE and BURG), or enough power for two D1255
keypads; two D1255RB, D1256RB, or D1257RB
keypads; two D1260 keypads, or one D1265 keypad.
An external power supply, connected with a common
ground, is required to provide power for devices that
exceed the 550 mA limit.
A total of up to 32 SDI devices can connect to the
output buses. A fault to the power or data connections
of one bus does not affect the other bus.

2 | ICP-SDI-9114 SDI Splitter

Certifications and approvals

Region Certification

USA UL UOXX: Control Unit Accessories, System

(UL864, 9th edition)

CSFM 7167-1615:0243 7167 -- CONTROL

UNIT (HOUSEHOLD)

CSFM 7165-1615:0242 7165 -- FIRE ALARM

CONTROL UNIT (COMMERCIAL)

CSFM 7165-1615:0238 7165 -- FIRE ALARM

CONTROL UNIT (COMMERCIAL)

CSFM 7165-1615:0119 7165 -- FIRE ALARM

CONTROL UNIT (COMMERCIAL)

CSFM 7167-1615:0239 7167 -- CONTROL

UNIT (HOUSEHOLD)

FDNY-

6174

CoA

Installation/configuration notes

Compatible Control Panels

• B9512G/B9512G-E

• B8512G/B8512G-E

• D9412GV4/D7412GV4/D7212GV4

• D9412GV3/D7412GV3/D7212GV3

• D9412GV2/D7412GV2/D7212GV2

1

The D7212GV4, D7212GV3, and D7212GV2 are not

1

1

1

listed for commercial fire applications.

• D9124 Fire Alarm Control Panel

Mounting Considerations

Parts included

Quant. Component

1 SDI splitter

1 Hardware pack

1 Literature pack

Technical specifications

Environmental Considerations

Relative Humidity: 93% maximum, non‑condensing

Temperature (operating): 0°C to +50°C (+32°F to +122°F)

Mechanical Properties

Dimensions (H x W x D): 127 mm x 74 mm x 25.4 mm

(5 in. x 2.9 in. x 1 in.)

Weight: 0.13 kg (4.6 oz)

Outputs

Current (BURG bus): 550 mA maximum from control panel

Current (FIRE bus): 550 mA maximum from control panel

Power Requirements

Current: 30 mA maximum

Voltage (supply): 12.0 VDC nominal

Notice

UL requires that the SDI splitter be mounted in
the same enclosure with the control panel, or in a
separate enclosure in the same room within 20 ft
(6.0 m) of the control panel and connected by
conduit.

Wiring Considerations

Wiring from the control panel to SDI splitter should be

0.8 mm (22 AWG) to 2.0 mm (12 AWG) wire with a
maximum wire length of 6.0 m (20 ft). The maximum
impedance of the wire from the control panel to the
SDI splitter must not exceed 1 Ω.
The maximum total wiring length for any single bus is
3048 m (10,000 ft). To determine the maximum
impedance, maximum wire length and appropriate
wire gauge for wiring from the SDI splitter to the SDI
devices, refer to the specifications for each SDI
device.

Trademarks

All hardware and software product names used in this
document are likely to be registered trademarks and
must be treated accordingly.

Ordering information

ICP-SDI-9114 SDI Splitter

Provides the ability to set up two independent SDI
buses from a single SDI connection on the control
panel.

Order number ICP-SDI-9114