Bosch HGZIT301, HDZIT301 Installation Manual

INSTALLATION MANUAL

For Island Trim Kits

Models/
Modèles/
Modelos:

MANUEL D’INSTALLATION

Pour Nécessaires de Garniture d'Îlot

MANUAL DE INSTALACIÓN

para kits de molduras para islas

HGZIT301
HDZIT301

Safety Definitions

9 WARNING:

If the information in this manual is not followed exactly, a
fire or explosion may result causing property dama ge ,
personal injury or death.

-- Do not store or use combustible materials,
gasoline or other flammable vapors and liquids
in the vicinity of this or any other appliance.

-- WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switch.

• Do not use any phone in your building.

• Immediately call your gas supplier from a

neighbor’s phone. Follow the gas supplier’s
instructions.

• If you cannot reach your gas supplier, call

the fire department.

-- Installation and service must be perf ormed by a
qualified installer, authorized service agency or
the gas supplier.

WARNING

9

This indicates that death or serious injuries may
occur as a result of non-observance of this warning.

CAUTION

9

This indicates that minor or moderate injuries may
occur as a result of non-observance of this warning.

NOTICE: This indicates that damage to the appliance or
property may occur as a result of non-compliance with this
advisory.

Note: This alerts you to important information and/or tips.

9001040675 Rev B English 1

9 IMPORTANT SAFETY INSTRUCTIONS

READ AND SAVE THESE INSTRUCTIONS

9 WARNING

• If the information in this manual is not followed
exactly, property damage or personal injury may
result.

• Read the instructions completely before
attempting one of these procedures.

• Installation of Island Trim requires access to the
mounting screws on the back and sides of the
range. If electrical or gas connections prevent
access to the screws, contact a qualified
technician before proceeding.

9 WARNING

• DO NOT block or obstruct the flow of air through
the ventilation openings. The oven vents are
located at the back of the range. The vents need
to be unobstructed and open to provide
necessary airflow for proper oven performance.

• DO NOT touch the oven vent area while the
range is on and for several minutes after the
range is off. Some parts of the vents and
surrounding area become hot enough to cause
burns. Allow range sufficient time to cool before
touching or cleaning vent areas.

• DO NOT position plastic or other heat sensitive
items on or near the oven vents. These items
could melt or ignite.

Appliance Handling Safety

9 WARNING

TIP OVER HAZARD!

A child or adult can tip the
range over and be killed.
Verify that the anti-tip
bracket is securely installed.
Ensure the anti-tip bracket
is engaged whenever the
range is moved to a new
location.

Do not operate the range without the anti-tip bracket
in place. Failure to follow the instructions in this
manual can result in death or serious burns to
children and adults.

Check for proper installation and use of the anti-tip
bracket. Carefully tip the range forward pulling from
the back to ensure that the anti-tip bracket engages
the range leg and prevents tip-over. Range should
not move more than 1” (25 mm).

NOTICE

Proper Handling Technique

To avoid risk of damage to the range oven door, do
not lift, push, or pull the range by holding the door
handle. Take care not to touch the oven heating
element (dual fuel range) also located at the top of
the oven cavity, just behind the ridged area.

9 CAUTION

• The range is heavy and requires at least two
persons or proper equipment to move.

• Hidden surfaces may have sharp edges. Use
gloves and caution when reaching behind or
under appliance.

Do not move the range using the oven door handle. You
may wish to remove the oven door for easier handling. See
the Installation Manual for your range for more information.

Turn power OFF at the service pan el. Lock service panel to
prevent power from being turned ON acc ide n tally.

Refer to range data plate for more information. See the
Installation Manual for your range for the data plate
location.

9001040675 Rev B English 2

Note: It is recommended to wear gloves and long
sleeves to protect hands and forearms from
abrasion and potential scratches during the sliding
process. It is also recommended to take off watches
and jewelry and to wear work shoes during
installation for foot protection.

Island Trim Installation

Island Trim Installation
Recommendations

The Island Trim is intended for slide-in range inst allations in
a kitchen island or peninsula, not for installations against a
wall.

To help prevent inadvertant cont act with a hot Island T rim, it
is suggested that a minimum 6” (152.4 mm) clearance be
maintained between the rear and sid es of the slide-in range
cut out and the outside of the island. Figure 1: Minimum
recommended range cut out clearance. See the Slide-In
Range Installation Manual for other clearance information.

• Read the Tip Over Wa rning in the Safety section of this
manual. Be aware of this when the range has been
pulled out of the anti-tip bracket for this installation.

Procedure

1. Confirm that the range surfaces and cookto p grates are
cool enough to be comfortably touched.

2. Slide the range out enough to access the re ar louver
cover mounting screws. Read the Proper Handling
Technique Notice in the Safety Section of this manual.

3. Remove the four screws holding the rear louver cover.
Save these screws to reattach the louver cover. See
Figure 2: Rear louver cover screw locations.

Figure 1: Minimum recommended range cut out clearance

Procedure for a Gas Slide-In
Range (HGI8054, HGIP054
ranges only)

Tools Needed

• Torx T20 screwdriver

•gloves

Preparation

IMPORTANT!

Can the range slide out enough to give access to the rear
and side screws of the rear louver cover and rear vent trim?
See Figure 2: Rear louver cover screw locations and Figure
3: Trim screw locations (louver cover removed).

• If the range can slide out, continue to the Procedure.

• If the range cannot slide out, contact a qualified service
person to disconnect the gas or electrical connections
that prevent the range from being pulled out before
continuing to the Procedure.

Figure 2: Rear louver cover screw locations

4. Lift the louver cover out of the slots holding it in place.
Note the slot locations for later. See Figure 3: Trim
screw locations (louver cover removed).

5. Remove the cooktop grates.

6. Remove the screws holding the trim (five screws on the
back and one screw on each end). Save two of these
screws for installation of Island Trim. See Figure 3:
Trim screw locations (louver cover removed).

Figure 3: Trim screw locations (louver cover removed)

7. Rotate the trim forward and lift it off.

9001040675 Rev B English 3

8. Install five stand-off screws (included in the Island T rim
kit) in the back of the range, in the same locations as
the original 5 rear trim screws. See .Figure 3: Trim
screw locations (louver cover removed)

Figure 4: Stand-off Screws

9. Place the rear louver cover into its slots and secure
with the four original screws.

10. Place the Island Trim in position A (Figure 5: Island
Trim placement 1) and move it to position B (towards
the rear of the range) as shown to engage the
alignment device 1 (the appearance of the device may
not be exactly as shown).

11. Rotate the Island Trim into position where the Island
Trim side mounting hole 2 is visible through hole 3 on
both sides of the range(see Figure 6: Island Trim
placement 2.

Figure 6: Island Trim placement 2

12. Secure the Island Trim with one screw through hole 3
at each end (see “Island Trim placement 2” on page 4
and “Island Trim Installed” on page 4).

13. Replace the cooktop grates back into their normal
positions.

Figure 7: Island Trim Installed

14. If necessary, have a qualified service person reattach
electrical or gas connections.

15. Slide the range back into position, being sure to
engage the anti-tip bracket. See the Tip Over Hazard
Warning earlier in this instruction and also in the Slide­In Range Installation Manual.

Figure 5: Island Trim placement 1

English 4 9001040675 Rev B

Procedure for a Dual Fuel
Slide-In Range (HDI8054,
HDIP054 ranges only)

Tools Needed

• Torx T20 screwdriver

•gloves

Preparation

IMPORTANT!

Can the range slide out enough to have access to the rear
and side trim screws? See Figure 1: Trim Screws, Dual
Fuel Range.

• If the range can slide out, go to the Procedure.

• If the range cannot out, contact a qualified service
person to disconnect the gas or electrical connections
that prevent the range from being pulled out before
continuing to the Procedure.

• Read the Tip Over W arning in the Safety sectio n of this
manual. Be aware of this hazard when the range has
been pulled out for this installation.

Figure 2: Island Trim placement

7. Secure the Island Trim with one screw at each end and
five screws in the back. See Figure 1: Trim Screws,
Dual Fuel Range.

8. Replace the cooktop grates back into their normal
positions,

Procedure

1. Confirm that the range surfaces and cooktop grates are
cool enough to be comfortably touched.

2. Slide the range out enough to access the trim mounting
screws (see Figure 1: Trim Screws, Dual Fuel Range).

Figure 1: Trim Screws, Dual Fuel Range

3. Remove the cooktop grates.

4. Remove the screws holding the trim (five screws on the
back and one screw on each end). Save the screws for
installing the Island Trim (see Figure 1: Trim Screws,
Dual Fuel Range).

5. Lift the trim up to remove.

6. Lower the Island Trim into place, aligning the Island
Trim hole 1 with the hole at 2 on both sides of the
range. See Figure 2: Island Trim placement.

Figure 3: New Island Trim Installed

9. If necessary, have a qualified service person reattach
electrical or gas connections.

10. Slide the range back into position, being sure to
engage the anti-tip bracket. See the Tip Over Hazard
Warning earlier in this instruction and also in the Slide­In Range Installation Manual.

9001040675 Rev B English 5

English 6 9001040675 Rev B