Bosch HBN445AUC, HBN442AUC, HBN462AUC, HBN465AUC, HBN466AUC Installation Instructions Manual
...
BOSCH
INSTALLATION INSTRUCTION MANUAL
for
Bosch Electric Built-in
Single & Double Oven Models HBN 44../45../46..
MANUEL D'INSTALLATION
four 61ectrique Bosch encastr6,
simple et double
Models HBN 44../45../46..
Ed. 01-02
BOSCH
INSTALLATION INSTRUCTION MANUAL
for
Bosch Electric Built-in
Single & Double Oven Models HBN 44../45../46..
BEFORE YOU BEGIN, READ THESE INSTRUCTIONS COMPLETELY AND CAREFULLY
IMPORTANT: Save these instructions for the local electrical inspector's use
INSTALLER: Please leave this manual with owner for future reference.
OWNER: Please keep this manual for future reference
Table of Contents
INTRODUCTION .............................................................................................................................
TOOLS YOU WILL NEED ........................................................................................................
POWER REQUIREMENTS .......................................................................................................
CHOOSING OVEN LOCATION ...............................................................................................
STEPS FOR INSTALLATION ..................................................................................................
TECHNICAL DATA .........................................................................................................................
SINGLE OVEN ............................................................................................................................
DOUBLE OVEN ..........................................................................................................................
UNDERCOUNTER INSTALLATION ..........................................................................................
SINGLE OVEN ............................................................................................................................
WALL INSTALLATION .................................................................................................................
SINGLE OVEN ............................................................................................................................
DOUBLE OVEN ..........................................................................................................................
ELECTRICAL SUPPLY ..................................................................................................................
WIRING REQUIREMENTS ......................................................................................................
CONNECTING TO 208 VOLT CIRCUIT ...............................................................................
ELECTRICAL CONNECTIONS ...................................................................................................
3-WIRE BRANCH CIRCUIT .....................................................................................................
4-WIRE BRANCH CIRCUIT .....................................................................................................
FINAL CHECKLIST ........................................................................................................................
3
3
3
3
3
4
4
4
5
5
6
6
7
8
8
9
10
10
10
11
INTRODUCTION
Please read these instructions COMPLETELY
AND CAREFULLY. They will save you time and
effort and help to ensure optimum oven perform-
ance. Be sure to observe all WARNINGS.
These installation instructions are intended for
use by a qualified installer. In addition to these in-
structions the oven shall be installed:
• In the United States, in accordance with the Na-
tional Electric Code/State and Municipal codes
and/or local codes.
• In Canada, in accordance with Canadian Elec-
tric Code C22.1-1atest edition/Provincial and
Municipal codes and/or local codes.
These shall be carefully followed at all times.
Note: If installing your oven in Canada please
check to make sure that you have a model
with the UL Canadian listing mark, as
shown below:
The UL Canadian listing mark consists of the cir-
cled UL symbol preceded by the letter "C", as
shown. This should appear on the oven's rating
plate along with the UL United States listing
mark, which is the circled UL symbol above but
not preceded by the letter "C".
TOOLS YOU WILL NEED
The following tools are needed to install your new
oven:
• Tape measure and straightedge or ruler
• Pencil
• Phillips screwdriver
• Level
• Wire cutters and wire stripper
• 1" hole saw
• Hand or saber saw.
POWER REQUIREMENTS
The oven must be supplied with the proper volt-
age and frequency. The oven is manut:actured to
be connected to a three wire or four wire, single
phase, 240 volt, 60 Hz AC electrical supply on a
separate circuit fused on both sides of the line. If
a 208 volt circuit must be used, wiring inside the
oven must be modified. See Connection to a 208
Volt Circuit, in this manual. A circuit breaker or
time-delay fuse sized not to exceed the circuit rat-
ing of the appliance specified on the rating plate
located on the frame behind the door of the oven
is recommended.
The oven must be supplied with copper wires
ONLY.
It is recommended that you have the electrical
wiring and hook-up of your oven performed by a
qualified electrician. After installation is com-
plete have the electrician show you where the
main disconnect is and which of the circuit break-
ers/fuses are for the oven.
CHOOSING OVEN LOCATION
Carefully select the location where the oven will
be placed. The oven should be located for conven-
ient use in the kitchen, but away from strong
drafts. Strong drafts may be caused by open doors
or windows, or by heating and/or air conditioning
vents or fans. Make sure that electrical power can
be provided to the location selected.
STEPS FOR INSTALLATION
The following pages provide the necessary infor-
mation for proper installation of the oven ar-
ranged as tk_llows:
• Technical Data
• Installation Cutout Dimensions, Required
Clearances and Mounting instructions tk_r:
> Undercounter Installation, Single Oven
>Wall Installation, Single Oven
>Wall Installation, Double Oven
• Electrical Supply and Wiring Requirements
• Modifications required if Connecting to 208
Volt Circuit.
• Electrical Connections for 3-wire or 4-wire
Branch Circuit.
• Final Checklist.
TECHNICAL DATA
SINGLE OVEN
For cutout dimensions see following sections titled:
Preparing Location
Single Oven
Models
HBL 442A UC
HBL 445A UC
HBL 446A UC
Electrical Ratings
and Maximum Connected Load
Volts Hertz Amperes
@240V/208V
240/208 60 13.5/13.6
240/208 60 13.5/13.6
240/208 60 13.5/13.6
Watts
@240V/208V
3,250/2,820
3,250/2,820
3,250/2,820
Convection
Oven
Yes
Yes
Yes
DOUBLE OVEN
For cutout dimensions see following sections titled:
Preparing Location
Double Oven
Models
HBN 452A UC
HBN 455A UC
HBN 456A UC
HBN 462A UC
HBN 465A UC
HBN 466A UC
Electrical Ratings
and Maximum Connected Load
Volts Hertz Amperes
_I!240V/208V
240/208 60 26/26
240/208 60 26/26
240/208 60 26/26
240/208 60 26/26
240/208 60 26/26
240/208 60 26/26
Watts
?I!240V/208V
6,250/5,400
6,250/5,400
6,250/5,400
6,250/5,400
6,250/5,400
6,250/5,400
Convection
Oven
(top/bottom)
Yes/No
Yes/No
Yes/No
Yes/Yes
Yes/Yes
Yes/Yes
J
J
UNDERCOUNTER INSTALLATION, SINGLE
¥
co
I
i
2:
I
_ I
I
I
w
I
Oven electrical supply:
Locate junction box in
adjacent cabinet or below
bottom support surface.
25-3/8" opening width
Bottom support surface must
be solid level and able to
support at least of 150 Ibs,
toe space area
26-5/8' width of oven door frame
!/4' min. distance
between oven door
frame and adjacent
doors or drawer fronts.
Note: Decorative inserts must
maintain minimum spacing as shown.
Secure oven to cabinet using the screws
provided. Screws should be inserted through the
mounting holes in the positions indicated in the
frame (open door to see frame and mounting
holes), Do not overtighten screws,
Note: Decorative inserts must
maintain minimum spacing as shown.
Refer to and follow Notes and Warning listed under Wall Installation, Single Oven (facing page)
WALL INSTALLATION, SINGLE OVEN
c
_.- Electrical
o=¢ supply
junction box
25-3/8" opening width
Note: l. Do not slide oven across floor. Dam-
age to floor covering or floor could re-
sult.
2. The oven support surt:ace must be a
minimum 3/4" thick plywood plat-
form, solid, level and flush with the
bottom of the cabinet cutout.
3. Use extreme caution when moving or
installing the oven. It is very heavy.
4. Be very careful when moving or in-
stalling the oven to avoid damage to
the oven frame or damage to the cabi-
nets.
5. Be sure to level oven. An oven that is
not level may provide poor or incon-
sistent baking results.
6. Be careful when placing oven. DO
NOT pinch the conduit between the
oven back or wall and the inner cabi-
net wall or floor.
Securely t:asten oven to cabinet using the
screws provided. Failure to do so could result
in oven moving or tipping during use and
causing damage to the oven or cabinets or per-
sonal injury.
WALL INSTALLATION, DOUBLE OVEN
i
Secure oven to cabinet usingthe screws
provided. Screws should be inserted
through the mounting holes in the
positions indicated in the frame (open
door to see frame and mounting holes).
Do not overtighten screws,
Note: 1. Do not slide oven across floor. Dam-
age to floor covering or floor could re-
sult.
2. The oven support surt:ace must be a
minimum 3/4" thick plywood plat-
form, solid, level and flush with the
bottom of the cabinet cutout.
3. Use extreme caution when moving or
installing the oven. It is very heavy.
4. Be very careful when moving or in-
stalling the oven to avoid damage to
the oven frame or damage to the cabi-
nets.
5. Be sure to level oven. An oven that is
not level may provide poor or incon-
sistent baking results.
6. Be careful when placing oven. DO
NOT pinch the conduit between the
oven back or wall and the inner cabi-
net wall or floor.
Securely fasten oven to cabinet using the
screws provided. Failure to do so could result
in oven moving or tipping during use and
causing damage to the oven or cabinets or per-
sonal iniury.
Loading...