BOSCH GV3 User Manual
GV3 Series Control Panels
EN
Owner's Manual
Supplement
GV3 Series Control Panels | Owner's Manual Supplement
System Requirements
Minimum system requirements for Classification in
accordance with ANSI/SIA CP-01-2000:
• UL Listed and Classified control unit Model D9412GV3,
D7412GV3, or D7212GV3
• UL Listed and Classified keypad Model D1256, D1257,
D1260, D1255, D1255R, or D1255 RW
• UL Listed Local Bell
The minimum firmware requirements for SIA CP-01 compliance
are:
Control Panel Firmware Version
D9412GV3 8.00 or later
D7412GV3 8.00 or later
D7212GV3 8.00 or later
2 Bosch Security Systems, Inc. | 2/10 | F01U143082-01
GV3 Series Control Panels | Owner's Manual Supplement
Contents
1.0 Introduction........................................................................5
2.0 General Commands............................................................5
2.1 Two-Man Rule ............................................................................ 5
2.1.1 Description.................................................................................. 5
2.1.2 Using the Two-Man Rule............................................................ 5
2.2 Early Ambush ............................................................................. 6
2.2.1 Description.................................................................................. 6
2.2.2 Using Early Ambush ................................................................... 6
2.3 Easy Exit Control ........................................................................ 7
2.3.1 Description.................................................................................. 7
2.3.2 Using Easy Exit Control.............................................................. 7
2.4 Passcode Follows Scope ...........................................................8
2.4.1 Description.................................................................................. 8
2.4.2 Using Passcode Follows Scope ................................................. 8
2.5 Passcode-Controlled Menu ........................................................ 9
2.5.1 Description.................................................................................. 9
2.5.2 Using Passcode Controlled Menus ............................................ 9
2.6 Walk Tests................................................................................ 10
2.6.1 Description................................................................................ 10
2.6.2 Using Walk Test ....................................................................... 10
2.7 Door Activated Custom Function.............................................. 12
2.7.1 Description................................................................................ 12
2.7.2 Using Door Activated Custom Functions: ................................ 12
2.8 Access Level Control................................................................ 13
2.8.1 Description................................................................................ 13
2.8.2 Using ACCESS LEVEL CTL? .................................................. 13
2.9 Door Control ............................................................................. 14
2.9.1 Description................................................................................ 14
2.9.2 Using Door Control? ........................................................... 14
2.9.3 Cycle Door?.......................................................................... 15
2.9.4 Unlock Door?........................................................................ 17
2.9.5 Secure Door?........................................................................ 17
Bosch Security Systems, Inc. | 2/10 | F01U143082-01 3
GV3 Series Control Panels | Owner's Manual Supplement
2.10 Delete User [COMMAND 53].................................................... 19
2.10.1 Description................................................................................19
2.10.2 Using DEL USER ?..................................................................19
2.11 Add/Change User - [COMMAND 56]........................................20
2.11.1 Description................................................................................20
2.11.2 Using Add User ?..................................................................20
3.0 SIA CP-01 Compliance Information.................................23
3.1 System Requirements ..............................................................23
3.2 False Alarm Reduction Features .............................................. 23
3.3 User-Caused False Alarms, Arming the System......................24
3.3.1 Exit Time Defaults..................................................................... 24
3.3.2 Exit Tone................................................................................... 24
3.3.3 Exit Time Restart ......................................................................24
3.3.4 Exit Error ...................................................................................24
3.3.5 Master Arm − No Exit Feature (Unvacated Premises) .............25
3.3.6 Recent Closing .........................................................................25
3.4 User-Caused False Alarms, Disarming the System ................. 25
3.4.1 Entry Time Defaults ..................................................................25
3.4.2 Passcode Disarms System (Area)............................................ 25
3.5 Arming and Disarming with Keyswitches..................................26
3.6 Alarm Transmission Sequence – Alarm Abort .........................26
3.6.2 Abort Window ...........................................................................26
3.6.3 Passcode Acknowledges Alarm ...............................................26
3.6.4 Alarms Acknowledged within the Abort Window ......................27
3.6.5 At the End of the Alarm Abort Window ..................................... 27
3.7 Cancel Report and Cancel Window..........................................27
3.8 Duress Alarm ............................................................................ 27
Tables
Table 1: Walk Test Menu Access.....................................................10
Table 2: Hardware States of Points .................................................11
Table 3: Key to Symbols ..................................................................16
Table 4: System Requirements........................................................23
4 Bosch Security Systems, Inc. | 2/10 | F01U143082-01
GV3 Series Control Panels | Owner's Manual Supplement
1.0 Introduction
This document supplements the Security System Owner’s Manual
(P/N: 71-06633-000) with the features for the GV3 Series. The
instructions for the commands listed in this document replace
those commands in the Security System Owner’s Manual. Refer to
the Owner’s Manual for the operation of your new security system
and its other basic features.
Place this supplement inside the Security System Owner’s
Manual.
2.0 General Commands
2.1 Two-Man Rule
2.1.1 Description
The Two-Man Rule adds an extra step to the disarming process by
requiring two unique passcodes to disarm an area from the same
keypad.
I have this feature.
I do not have this feature.
2.1.2 Using the Two-Man Rule
1. Ensure that the keypad shows idle armed text or Disarm Now.
2. Enter a valid passcode with the authority to Passcode Disarm
by pressing the [passcode digits] followed by the [ENTER] key
(D1260) or [ENT] key (D1255).
3. The keypad shows a request for the SECOND CODE:
4. Enter a second valid passcode with the authority to Passcode
Disarm by pressing the [passcode digits] followed by the
[ENTER] or [ENT] key. The second passcode must be different
from the first passcode.
The area is disarmed and ready for entry.
Bosch Security Systems, Inc. | 2/10 | F01U143082-01 5
GV3 Series Control Panels | Owner's Manual Supplement
2.2 Early Ambush
2.2.1 Description
Early Ambush adds an extra step to the disarming process by
requiring the entry of an additional passcode to confirm that the
area is secure. The second passcode can be same as the first or
different, depending upon the configuration. The first entry
disarms the area and the second entry stops an automatic timer
from sending a duress event.
2.2.2 Using Early Ambush
1. Ensure that the keypad shows idle armed text or Disarm Now.
2. Enter a valid passcode with the authority to Passcode Disarm
3. Ensure that the keypad shows idle disarmed text.
4. You can now search the area; however, you must enter the
5. Enter a second valid passcode with the authority to Passcode
6. The keypad shows CODE 2 VALIDATED to confirm that the
The area is disarmed and ready for entry.
I have this feature.
I do not have this feature.
by pressing the [passcode digits] followed by the [ENTER] key
(D1260) or [ENT] key (D1255).
second passcode before the preset Early Ambush Time
expires.
Disarm by pressing the [passcode digits] followed by the
[ENTER] or [ENT]key.
second passcode is accepted and the Early Ambush Window is
canceled.
6 Bosch Security Systems, Inc. | 2/10 | F01U143082-01
GV3 Series Control Panels | Owner's Manual Supplement
2.3 Easy Exit Control
2.3.1 Description
The GV2 Series control panels change from one armed state to
another armed state without disarming. The Easy Exit Control
feature decreases the number of keystrokes and simplifies system
operation. This feature is available by default and is always on.
2.3.2 Using Easy Exit Control
Switching armed states from Master to Perimeter:
1. Ensure that the keypad shows idle master armed text.
2. Press the [COMMAND] key. The keypad shows SYSTEM
COMMAND.
3. Press [3] to Perimeter Arm.
4. The keypad display shows the Exit Delay countdown.
5. Enter or exit from the premises.
Switching armed states from Perimeter to Master:
1. Ensure that the keypad shows idle perimeter armed text.
2. Press the [COMMAND] key. The keypad shows SYSTEM
COMMAND.
3. Press [1] to Master Arm.
4. The keypad shows the Exit Delay countdown.
5. Enter or exit from the premises.
Bosch Security Systems, Inc. | 2/10 | F01U143082-01 7
GV3 Series Control Panels | Owner's Manual Supplement
2.4 Passcode Follows Scope
2.4.1 Description
The Passcode Follows Scope feature is an optional arming and
disarming restriction that can be enabled on keypads with access
to multiple areas. When this feature is set to No, the keypad
restricts Passcode Arming and Passcode Disarming to the home
area of the keypad. When set to Yes, this feature allows users to
arm or disarm all the areas to which they and the keypad have
access. This feature causes no restrictions to the keypad scope as
it pertains to any command or arming method other than
Passcode Arming or Passcode Disarming.
2.4.2 Using Passcode Follows Scope
Arming from a keypad with Panel Wide scope and Passcode
Follows Scope enabled:
1. Ensure that the keypad shows idle disarmed text.
2. Ensure that you have a valid passcode with the authority to
3. Enter your passcode by pressing the [passcode digits]
4. The keypad shows ARMING: 12345678 to indicate which areas
5. The keypad shows the exit delay countdown.
6. Exit from the premises.
Arming from a keypad with Panel Wide scope and Passcode
Follows Scope disabled (default):
1. Ensure that the keypad shows idle disarmed text.
2. Ensure that you have a valid passcode with the authority to
3. Enter your passcode by pressing the [passcode digits]
4. The keypad shows the exit delay countdown.
5. Exit from the premises.
I have this feature.
I do not have this feature.
Passcode Arm in all areas.
followed by the [ENTER] key (D1260) or [ENT] key (D1255).
are ready to enter exit delay and arm.
Passcode Arm in all areas.
followed by the [ENTER] key (D1260) or [ENT] key (D1255).
8 Bosch Security Systems, Inc. | 2/10 | F01U143082-01
GV3 Series Control Panels | Owner's Manual Supplement
2.5 Passcode-Controlled Menu
2.5.1 Description
When enabled, the system prompts users to enter a passcode
before viewing the keypad menu. The system shows the user the
menu options allowed according to their authority level, thereby
providing users only pertinent commands and functions.
2.5.2 Using Passcode Controlled Menus
On a D1255 Keypad with the Passcode Controlled Menu enabled:
1. Press the [ESC] key. The keypad shows ENTER PASSCODE.
2. Enter your passcode by pressing the [passcode digits]
On a D1260 Keypad with the Passcode Controlled Menu enabled:
1. Press the [Menu>] soft key in the lower right corner. The
2. Enter your passcode by pressing the [passcode digits]
The first and second menu items for which you have authority
appear.
I have this feature.
I do not have this feature.
followed by the [ENT] key. The first menu item for which you
have authority appears.
keypad responds with Enter passcode: then press [ENTER]
display.
followed by the [ENTER] key.
Bosch Security Systems, Inc. | 2/10 | F01U143082-01 9
Loading...