Bosch GSS 230 User Manual

Robert Bosch Power Tools GmbH

1 609 92A 4C2

70538 Stuttgart
GERMANY

www.bosch-pt.com

1 609 92A 4C2 (2019.01) O / 35

GSS 230 Professional

en Original instructions
zh 正本使用说明书
zh 原始使用說明書
ko 사용 설명서 원본
th หนังสือคู่มือการใช้งานฉบับ

ต้นแบบ

id Petunjuk-Petunjuk untuk Penggun-

aan Orisinal

vi Bản gốc hướng dẫn sử dụng

2 |

English . . .. .. .. .. .. . .. .. .. .. .. .. .. .. .. .. .. . .. .. .. .. .. . .. .. Page 5

中文 . .. .. .. .. .. . .. .. .. .. .. . .. .. .. .. .. . .. .. .. .. .. . .. .. .. .. .. 页 11

繁體中文. .. .. .. .. .. . .. .. .. .. .. . .. .. .. .. .. . .. .. .. .. .. . .. .. . 頁 14

한국어 .. .. .. .. .. .. .. .. .. . .. .. .. .. .. . .. .. .. .. .. . .. .. .. 페이지 17

ไทย. .. .. .. .. .. .. .. .. . .. .. .. .. .. . .. .. .. .. .. . .. .. .. .. .. . .. . หน้า 21

Bahasa Indonesia. .. .. .. .. .. .. .. . .. .. .. .. .. . .. .. .. .. .. Halaman 25

Tiếng Việt . .. .. .. .. .. .. .. .. .. .. . .. .. .. .. .. . .. .. .. .. .. .. .. Trang 29

1 609 92A 4C2 | (14.01.2019) Bosch Power Tools

GSS 230

(1)

(2)

(3)

(4)

(5)

(6)

(7)

(8)

(9)

| 3

Bosch Power Tools 1 609 92A 4C2 | (14.01.2019)

4 |

4

3

5

1

2

A B

C D

(6)

(7) (8)

(6)

(3)

(4)

(5)(10)

1 609 92A 4C2 | (14.01.2019) Bosch Power Tools

English

Safety instructions

General Power Tool Safety Warnings

WARNING

tions provided with this power tool. Failure to follow all in-

structions listed below may result in electric shock, fire and/
or serious injury.

Save all warnings and instructions for future reference.

The term "power tool" in the warnings refers to your mains­operated (corded) power tool or battery-operated (cord­less) power tool.

Work area safety

u Keep work area clean and well lit. Cluttered or dark

areas invite accidents.

u Do not operate power tools in explosive atmospheres,

such as in the presence of flammable liquids, gases or
dust. Power tools create sparks which may ignite the dust

or fumes.

u Keep children and bystanders away while operating a

power tool. Distractions can cause you to lose control.

Electrical safety

u Power tool plugs must match the outlet. Never modify

the plug in any way. Do not use any adapter plugs with
earthed (grounded) power tools. Unmodified plugs and

matching outlets will reduce risk of electric shock.

u Avoid body contact with earthed or grounded sur-

faces, such as pipes, radiators, ranges and refrigerat­ors. There is an increased risk of electric shock if your

body is earthed or grounded.

u Do not expose power tools to rain or wet conditions.

Water entering a power tool will increase the risk of elec­tric shock.

u Do not abuse the cord. Never use the cord for carry-

ing, pulling or unplugging the power tool. Keep cord
away from heat, oil, sharp edges or moving parts.

Damaged or entangled cords increase the risk of electric
shock.

u When operating a power tool outdoors, use an exten-

sion cord suitable for outdoor use. Use of a cord suit­able for outdoor use reduces the risk of electric shock.

u If operating a power tool in a damp location is un-

avoidable, use a residual current device (RCD) protec­ted supply. Use of an RCD reduces the risk of electric

shock.

Personal safety

u Stay alert, watch what you are doing and use common

sense when operating a power tool. Do not use a
power tool while you are tired or under the influence
of drugs, alcohol or medication. A moment of inatten-

Read all safety warnings, instruc­tions, illustrations and specifica-

English | 5

tion while operating power tools may result in serious per­sonal injury.

u Use personal protective equipment. Always wear eye

protection. Protective equipment such as a dust mask,
non-skid safety shoes, hard hat or hearing protection
used for appropriate conditions will reduce personal in­juries.

u Prevent unintentional starting. Ensure the switch is in

the off-position before connecting to power source
and/or battery pack, picking up or carrying the tool.

Carrying power tools with your finger on the switch or en­ergising power tools that have the switch on invites acci­dents.

u Remove any adjusting key or wrench before turning

the power tool on. A wrench or a key left attached to a
rotating part of the power tool may result in personal in­jury.

u Do not overreach. Keep proper footing and balance at

all times. This enables better control of the power tool in
unexpected situations.

u Dress properly. Do not wear loose clothing or jew-

ellery. Keep your hair and clothing away from moving
parts. Loose clothes, jewellery or long hair can be caught

in moving parts.

u If devices are provided for the connection of dust ex-

traction and collection facilities, ensure these are con­nected and properly used. Use of dust collection can re-

duce dust-related hazards.

u Do not let familiarity gained from frequent use of tools

allow you to become complacent and ignore tool
safety principles. A careless action can cause severe in-

jury within a fraction of a second.

Power tool use and care

u Do not force the power tool. Use the correct power

tool for your application. The correct power tool will do
the job better and safer at the rate for which it was de­signed.

u Do not use the power tool if the switch does not turn it

on and off. Any power tool that cannot be controlled
with the switch is dangerous and must be repaired.

u Disconnect the plug from the power source and/or re-

move the battery pack, if detachable, from the power
tool before making any adjustments, changing ac­cessories, or storing power tools. Such preventive

safety measures reduce the risk of starting the power tool
accidentally.

u Store idle power tools out of the reach of children and

do not allow persons unfamiliar with the power tool or
these instructions to operate the power tool. Power

tools are dangerous in the hands of untrained users.

u Maintain power tools and accessories. Check for mis-

alignment or binding of moving parts, breakage of
parts and any other condition that may affect the
power tool’s operation. If damaged, have the power
tool repaired before use. Many accidents are caused by

poorly maintained power tools.

Bosch Power Tools 1 609 92A 4C2 | (14.01.2019)

6 | English

u Keep cutting tools sharp and clean. Properly main-

tained cutting tools with sharp cutting edges are less
likely to bind and are easier to control.

u Use the power tool, accessories and tool bits etc. in

accordance with these instructions, taking into ac­count the working conditions and the work to be per­formed. Use of the power tool for operations different

from those intended could result in a hazardous situation.

u Keep handles and grasping surfaces dry, clean and

free from oil and grease. Slippery handles and grasping
surfaces do not allow for safe handling and control of the
tool in unexpected situations.

Service

u Have your power tool serviced by a qualified repair

person using only identical replacement parts. This
will ensure that the safety of the power tool is maintained.

Safety Warnings for Sander

u Only use the power tool for dry sanding. Water entering

a power tool will increase the risk of electric shock.

u Warning: Danger of fire! Avoid overheating the work-

piece and the sander. Always empty the dust collector
before taking a break from work. Sanding dust in the

dust bag, microfilter, paper bag (or in the filter bag or va­cuum cleaner filter) can spontaneously combust under
certain conditions, for example if flying sparks are cre­ated when sanding metals. This risk is increased if the
sanding dust is mixed with paint or polyurethane residue
or with other chemical substances and if the workpiece is
hot as a result of prolonged work.

u Clean the air vents on your power tool regularly. The

motor’s fan will draw the dust inside the housing and ex­cessive accumulation of powdered metal may cause elec­trical hazards.

u Secure the workpiece. A workpiece clamped with

clamping devices or in a vice is held more secure than by
hand.

u Always wait until the power tool has come to a com-

plete stop before placing it down.

Products sold in GB only:

Your product is fitted with an BS 1363/A approved electric
plug with internal fuse (ASTA approved to BS 1362).

If the plug is not suitable for your socket outlets, it should be
cut off and an appropriate plug fitted in its place by an au­thorised customer service agent. The replacement plug
should have the same fuse rating as the original plug.

The severed plug must be disposed of to avoid a possible
shock hazard and should never be inserted into a mains
socket elsewhere.

Product Description and Specifications

Read all the safety and general instructions.

Failure to observe the safety and general in­structions may result in electric shock, fire
and/or serious injury.

Please observe the illustrations at the beginning of this oper­ating manual.

Intended Use

The power tool is intended for dry sanding of wood, plastic,
metal, filler and varnished surfaces.

Product features

The numbering of the product features refers to the diagram
of the power tool on the graphics page.

On/off switch

(1)

Lock-on button for on/off switch

(2)

Rear clamping bracket

(3)

Unlocking lever for rear clamping bracket

(4)

Sanding plate

(5)

Sanding sheet

(6)

Release button for front clamping bracket

(7)

Front clamping bracket

(8)

Handle (insulated gripping surface)

(9)

Screws for sanding plate

(10)

A)

Accessories shown or described are not included with the
product as standard. You can find the complete selection of
accessories in our accessories range.

A)

Technical data

Orbital sander GSS 230 GSS 230

Article number

Rated power input W 160 190
No-load speed min
No-load orbital stroke rate min

-1

-1

Orbit diameter mm 2.0 2.0
Sanding sheet dimensions
Clamping tension mm 93 x 230 93 x 230
Sanding plate dimensions mm 92 x 182 92 x 182
Weight according to EPTA-Procedure 01:2014 kg 1.7 1.7

1 609 92A 4C2 | (14.01.2019) Bosch Power Tools

3 601 K70 0B. 3 601 K70 0..

12,000 12,000
24,000 24,000

English | 7

Orbital sander GSS 230 GSS 230

Protection class

The specifications apply to a rated voltage [U] of 230 V. These specifications may vary at different voltages and in country-specific models.

/ II / II

Assembly

u Pull the plug out of the socket before carrying out any

work on the power tool.

Dust/Chip Extraction

Dust from materials such as lead-containing coatings, some
wood types, minerals and metal can be harmful to one’s
health. Touching or breathing-in the dust can cause allergic
reactions and/or lead to respiratory infections of the user or
bystanders.

Certain dust, such as oak or beech dust, is considered carci­nogenic, especially in connection with wood-treatment ad­ditives (chromate, wood preservative). Materials containing
asbestos may only be worked by specialists.

– Provide for good ventilation of the working place.
– It is recommended to wear a P2 filter-class respirator.
Observe the relevant regulations in your country for the ma-

terials to be worked.

u Avoid dust accumulation at the workplace. Dust can

easily ignite.

Changing the sanding sheet

Remove dirt and dust from the sanding plate (5), e.g. with a
brush, before attaching a new sanding sheet.

Sanding sheets without hook-and-loop backing (see figures A–C)

❶

Press and hold down the release button (7).

❷

Guide the sanding sheet (6) underneath the open front
clamping bracket (8) to the stop and let go of the release
button (7) again. Make sure that the sanding sheet is
clamped in the centre.

❸

Press and hold the unlocking lever (4).

❹

Position the sanding sheet (6) so that it fits tightly
around the sanding plate. Guide the other end of the
sanding sheet (6) underneath the open rear clamping
bracket (3).

❺ Hold on to the sanding sheet so that it is tensioned, then

let go of the unlocking lever (4) again to lock in the sand­ing sheet.

To remove the sanding sheet (6), press the unlocking lever
(4) and pull the sanding sheet out of the rear bracket. Press
the release button (7) and completely remove the sanding
sheet.

Selecting a sanding sheet

Different sanding sheets are available, depending on the ma­terial you are working with and the required surface removal
rate:

Grit

40–240

For processing all wood and wood-based ma­terials

For pre-sanding, e.g. of rough and un­even beams and boards

For surface sanding and levelling of
slight irregularities

For finish-sanding and fine sanding of
hardwoods

For processing paint and lacquer layers or
primers such as fillers and bodyfillers

For sanding down paint Coarse 40, 60
For sanding undercoats Medium 80, 100,

For final sanding of primers prior to
painting

Coarse 40, 60

Medium 80, 100,

120

Fine 180, 240

40–320

120

Fine 180, 240,

320

Changing the sanding plate (see figure D)

If necessary, the sanding plate (5) can be replaced.
Unscrew the four screws (10) completely and remove the

sanding plate (5). Fit the new sanding plate (5) and
retighten the screws.

Operation

Starting Operation

u Pay attention to the mains voltage. The voltage of the

power source must match the voltage specified on the
rating plate of the power tool. Power tools marked
with 230V can also be operated with 220V.

u Products that are only sold in AUS and NZ: Use a resid-

ual current device (RCD) with a nominal residual current
of 30 mA or less.

Switching on/off

u Make sure that you are able to press the On/Off switch

without releasing the handle.

To switch on the power tool, press and hold the on/off
switch (1).

To lock the on/off switch (1) press and hold it while also
pushing the lock-on button (2).

Bosch Power Tools 1 609 92A 4C2 | (14.01.2019)

8 | English

To switch off the power tool, release the on/off switch (1).
If the on/off switch (1) is locked, press the switch first and
then release it.

Practical advice

u Pull the plug out of the socket before carrying out any

work on the power tool.

u Always wait until the power tool has come to a com-

plete stop before placing it down.

The material removal rate when sanding is primarily determ­ined by the choice of sanding sheet.

Only immaculate sanding sheets achieve good sanding per­formance and make the power tool last longer.

Be sure to apply consistent contact pressure in order to in­crease the lifetime of the sanding sheets.

Excessively increasing the contact pressure will not lead to
increased sanding performance, rather it will cause more
severe wear of the power tool and of the sanding sheet.

Do not use a sanding sheet for other materials after it has
been used to work on metal.

Use only original Bosch-sanding accessories.

Maintenance and Servicing

Maintenance and Cleaning

u Pull the plug out of the socket before carrying out any

work on the power tool.

u To ensure safe and efficient operation, always keep

the power tool and the ventilation slots clean.

In order to avoid safety hazards, if the power supply cord
needs to be replaced, this must be done by Bosch or by an
after-sales service centre that is authorised to repair Bosch
power tools.

After-sales Service and Advice on Using Products

Our after-sales service can answer questions concerning
product maintenance and repair, as well as spare parts. You
can find exploded drawings and information on spare parts
at: www.bosch-pt.com
The Bosch product use advice team will be happy to help you
with any questions about our products and their accessor­ies.
www.powertool-portal.de, the internet portal for trades­people and DIY enthusiasts.

In all correspondence and spare parts orders, please always
include the 10‑digit article number given on the type plate of
the product.

Cambodia

Robert Bosch (Cambodia) Co., Ltd
Unit 8BC, GT Tower, 08th Floor, Street 169,
Czechoslovakia Blvd, Sangkat Veal Vong
Khan 7 Makara, Phnom Penh
VAT TIN: 100 169 511
Tel.: [phone]

Tel.: [phone]
www.bosch.com.kh

People’s Republic of China
China Mainland

Bosch Power Tool (China) Co. Ltd.
Bosch Service Center
567, Bin Kang Road
Bin Kang District
Hangzhou, Zhejiang Province
China 310052
Tel.: [phone] / 5588
Fax: [phone] x 5566# / 5588#
E-mail: [e-mail]
www.bosch-pt.com.cn

HK and Macau Special Administrative Regions

Robert Bosch Co. Ltd.
21st Floor, 625 King’s Road
North Point, Hong Kong
Customer Service Hotline: [phone]
Fax: [phone]
E-mail: [e-mail]
www.bosch-pt.com.hk

India

Bosch Service Center
69, Habibullah Road, (next to PSBB School), T. Nagar
Chennai–600077
Phone: [phone]

Bosch Service Center Rishyamook
85A, Panchkuin Road
New Delhi–110001
Phone: [phone]

Bosch Service Center 79,
Crystal Bldg., Dr. Annie Besant Road, Worli
Mumbai–400018
Phone: [phone] /
[phone] / [phone]

Indonesia

PT Robert Bosch
Palma Tower 10th Floor
Jalan RA Kartini II-S Kaveling 6
Pondok Pinang, Kebayoran Lama
Jakarta Selatan 12310
Tel.: [phone]
www.bosch-pt.co.id

Malaysia

Robert Bosch Sdn. Bhd.(220975-V) PT/SMY
No. 8A, Jalan 13/6
46200 Petaling Jaya
Selangor
Tel.: [phone]
Toll-Free: 1800 880188
Fax: [phone]
E-mail: [e-mail]
www.bosch-pt.com.my

Pakistan

Robert Bosch Middle East FZE – Pakistan Liaison Office
2nd Floor Plaza # 10, CCA Block, DHA Phase 5

1 609 92A 4C2 | (14.01.2019) Bosch Power Tools

English | 9

Lahore, 54810
Phone: [phone]
E-mail: [e-mail]

Philippines

Robert Bosch, Inc.
28th Floor Fort Legend Towers,
3rd Avenue corner 31st Street,
Fort Bonifacio, Global City,
1634 Taguig City
Tel.: [phone]
Fax: [phone]
www.bosch-pt.com.ph

Singapore

Powerwell Service Centre Ptd Ltd
Bosch Authorised Service Centre (Power Tools)
4012 Ang Mo Kio Ave 10, #01-02 TECHplace
Singapore 569628
Tel.: [phone]
Fax: [phone]
E-mail: [e-mail]
www.powerwellsc.com
www.bosch-pt.com.sg

Thailand

Robert Bosch Ltd.
Liberty Square Building
No. 287, 11 Floor
Silom Road, Bangrak
Bangkok 10500
Tel.: [phone]
Fax: [phone]
Robert Bosch Ltd., P. O. Box 2054
Bangkok 10501
www.bosch.co.th

Bosch Service – Training Centre
La Salle Tower Ground Floor Unit No.2
10/11 La Salle Moo 16
Srinakharin Road
Bangkaew, Bang Plee
Samutprakarn 10540
Tel.: [phone]
Fax: [phone]

Vietnam

Branch of Bosch Vietnam Co., Ltd in HCMC
14th floor, Deutsches Haus, 33 Le Duan
Ben Nghe Ward, District 1, Ho Chi Minh City
Tel.: [phone]
Fax: [phone]
Hotline: [phone]
E-mail: [e-mail]
www.bosch-pt.com.vn

Armenia, Azerbaijan, Georgia, Kyrgyzstan, Mongolia,
Tajikistan, Turkmenistan, Uzbekistan

TOO "Robert Bosch" Power Tools, After Sales Service
Rayimbek Ave., 169/1
050050, Almaty, Kazakhstan
Service e-mail: [e-mail]
Official website: www.bosch.com, www.bosch-pt.com

Bahrain

Hatem Al Juffali Technical Equipment Establishment.
Kingdom of Bahrain, Setra Highway, Al Aker Area
Phone: [phone]
Fax: [phone]
E-mail: [e-mail]

Egypt
Unimar

20 Markaz kadmat
El tagmoa EL Aoul – New Cairo
Phone: [phone]
Phone: [phone]
Fax: [phone]
E-mail: [e-mail]

Iran

Robert Bosch Iran
3rd Floor, No 3, Maadiran Building
Aftab St., Khodami St., Vanak Sq.
Tehran 1994834571
Phone: [phone]

Iraq

Sahba Technology Group
Al Muthana airport road
Baghdad
Phone: [phone]
Phone Dubai: [phone]
E-mail: [e-mail]

Jordan

Roots Arabia – Jordan
Nasser Bin Jameel street, Building 37 Al Rabiah
11194 Amman
Phone: [phone]
E-mail: [e-mail]

Kuwait

Al Qurain Automotive Trading Company
Shuwaikh Industrial Area, Block 1, Plot 16, Street 3rd
P.O. Box 164 – Safat 13002
Phone: [phone]
Fax: [phone]
E-mail: [e-mail]

Lebanon
Tehini Hana & Co. S.A.R.L.

P.O. Box 90-449
Jdeideh
Dora-Beirut
Phone: [phone]
E-mail: [e-mail]

Libya
El Naser for Workshop Tools

Swanee Road, Alfalah Area
Tripoli
Phone: [phone]

Oman
Malatan Trading & Contracting LLC

P.O. Box 131
Ruwi, 112 Sultanate of Oman

Bosch Power Tools 1 609 92A 4C2 | (14.01.2019)

10 | English

Phone: [phone]
E-mail: [e-mail]

Qatar

International Construction Solutions W L L
P. O. Box 51,
Doha Phone: [phone]
Fax: [phone]
E-mail: [e-mail]

Saudi Arabia

Juffali Technical Equipment Co. (JTECO)
Kilo 14, Madinah Road, Al Bawadi District
Jeddah 21431
Phone: [phone] Ext. 1528
Fax: [phone]
E-mail: [e-mail]

Syria

Dallal Establishment for Power Tools
P.O. Box 1030
Aleppo
Phone: [phone]
E-mail: [e-mail]

United Arab Emirates

Central Motors & Equipment LLC, P.O. Box 1984
Al-Wahda Street – Old Sana Building
Sharjah
Phone: [phone]
Fax: [phone]
E-mail: [e-mail]

Yemen

Abualrejal Trading Corporation
Sana’a Zubiery St. Front to new Parliament Building
Phone: [phone]
Fax: [phone]
E-mail: [e-mail]

Ethiopia

Forever plc
Kebele 2,754, BP 4806,
Addis Ababa
Phone: [phone]
E-mail: [e-mail]

Ghana

C.WOERMANN LTD.
Nsawam Road/Avenor Junction, P.O. Box 1779
Accra Phone: [phone]

Kenya

Robert Bosch East Africa Ltd
Mpaka Road P.O. Box 856
00606 Nairobi

Nigeria

Robert Bosch Nigeria Ltd.
52–54 Isaac John Street P.O. Box
GRA Ikeja – Lagos

Republic of South Africa
Customer service

Hotline: [phone]

Gauteng – BSC Service Centre
35 Roper Street, New Centre
Johannesburg
Tel.: [phone]
Fax: [phone]
E-mail: [e-mail]

KZN – BSC Service Centre
Unit E, Almar Centre
143 Crompton Street
Pinetown
Tel.: [phone]
Fax: [phone]
E-mail: [e-mail]

Western Cape – BSC Service Centre
Democracy Way, Prosperity Park
Milnerton
Tel.: [phone]
Fax: [phone]
E-mail: [e-mail]

Bosch Headquarters
Midrand, Gauteng
Tel.: [phone]
Fax: [phone]
E-mail: [e-mail]

Tanzania

Diesel & Autoelectric Service Ltd.
117 Nyerere Rd., P.O. Box 70839
Vingunguti 12109, Dar Es Salaam
Phone: [phone]

Australia, New Zealand and Pacific Islands

Robert Bosch Australia Pty. Ltd.
Power Tools
Locked Bag 66
Clayton South VIC 3169
Customer Contact Center
Inside Australia:
Phone: [phone]
Fax: [phone]

Inside New Zealand:
Phone: [phone]
Fax: [phone]

Outside AU and NZ:
Phone: [phone]
www.bosch-pt.com.au
www.bosch-pt.co.nz

Disposal

The power tool, accessories and packaging should be re­cycled in an environmentally friendly manner.

Do not dispose of power tools along with
household waste.

1 609 92A 4C2 | (14.01.2019) Bosch Power Tools

中文

安全规章

电动工具通用安全警告

警告！

导致电击、着火和／或严重伤 害。

保存所有警告和说明书以备查阅。

在所有下列的警告中术语" 电动工具" 指市电驱动
（有线）电动工具或电池驱动（无线）电动工具。

工作场地的安全

u 保持工作场地清洁和明亮。 混乱和黑暗的场地会

引 发事故。

u 不要在易爆环境，如有易燃液体、气体或粉尘的

环 境下操作电动工具。 电动工具产生的火花会点
燃粉 尘或气体。

u 让儿童和旁观者离开后操作电动工具。 注意力不

集 中会使操作者失去对工具的控制。

电气安全

u 电动工具插头必须与插座相配。绝不能以任何方

式 改装插头。需接地的电动工具不能使用任何转
换插 头。 未经改装的插头和相配的插座将减少电

击危 险。

u 避免人体接触接地表面，如管道、散热片和冰

箱。 如果你身体接地会增加电击危险。

u 不得将电动工具暴露在雨中或潮湿环境中。 水进

入 电动工具将增加电击危险。

u 不得滥用电线。绝不能用电线搬运、拉动电动工

具 或拔出其插头。使电线远离热源、油、锐边或
运动 部件。 受损或缠绕的软线会增加电击危险。

u 当在户外使用电动工具时，使用适合户外使用的

外 接软线。 适合户外使用的软线将减少电击危
险。

u 如果在潮湿环境下操作电动工具是不可避免的，

应 使用剩余电流动作保护器（RCD）。 使用
RCD 可减 小电击危险。

人身安全

u 保持警觉，当操作电动工具时关注所从事的操作

并 保持清醒。当你感到疲倦，或在有药物、酒精
或治 疗反应时，不要操作电动工具。在操作电动

工具时 瞬间的疏忽会导致严重人身伤害。

u 使用个人防护装置。始终佩戴护目镜。 安全装

置， 诸如适当条件下使用防尘面具、防滑安全
鞋、安全 帽、听力防护等装置能减少人身伤害。

u 防止意外起动。确保开关在连接电源和/ 或电池

盒、拿起或搬运工具时处于关断位置。 手指放在
已 接通电源的开关上或开关处于接通时插入插头
可能 会导致危险。

u 在电动工具接通之前，拿掉所有调节钥匙或扳

手。 遗留在电动工具旋转零件上的扳手或钥匙会
导致人 身伤害。

警告！ 阅读所有警告和所有说
明! 不遵照以下警 告和说明会

中文 | 11

u 手不要伸展得太长。时刻注意立足点和身体平

衡。 这样在意外情况下能很好地控制电动工具。

u 着装适当。不要穿宽松衣服或佩戴饰品。让衣

服、 手套和头发远离运动部件。 宽松衣服、佩饰
或长发 可能会卷入运动部件中。

u 如果提供了与排屑、集尘设备连接用的装置，要

确 保他们连接完好且使用得当。 使用这些装置可
减少 尘屑引起的危险。

u 即使由于经常使用电动工具而对此非常熟悉，也

不要就认为可以高枕无忧而忽略工具的安全规
定。粗心大意的行为可能在瞬间就造成严重的伤

害。

电动工具使用和注意事项电动工具使用和注意事项

u 不要滥用电动工具，根据用途使用适当的电动工

具。 选用适当设计的电动工具会使你工作更有
效、 更安全。

u 如果开关不能接通或关断工具电源，则不能使用

该 电动工具。 如果开关不能接通或关断工具电
源，则不能使用该 电动工具。

u 在进行任何调节、更换附件或贮存电动工具之

前， 必须从电源上拔掉插头和/ 或使电池盒与工
具脱 开。 这种防护性措施将减少工具意外起动的

危险。

u 将闲置不用的电动工具贮存在儿童所及范围之

外， 并且不要让不熟悉电动工具或对这些说明不
了解的 人操作电动工具。 电动工具在未经培训的

用户手中 是危险的。

u 保养电动工具。检查运动件是否调整到位或卡

住， 检查零件破损情况和影响电动工具运行的其
他状 况。如有损坏，电动工具应在使用前修理
好。 许多 事故由维护不良的电动工具引发。

u 保持切削刀具锋利和清洁。 保养良好的有锋利切

削 刃的刀具不易卡住而且容易控制。

u 按照使用说明书，考虑作业条件和进行的作业来

使 用电动工具、附件和工具的刀头等。 将电动工
具用 于那些与其用途不符的操作可能会导致危
险。

u 保持手柄和握持表面干燥、清洁、无油污。 在突

发情况下，滑溜的手柄和握持表面无法确保安全
地握持和控制工具。

维修

u 将电动工具用 于那些与其用途不符的操作可能会

导致危险。. 这样将确保所维修的电动工具的安全
性。

针对研磨机的安全规章

u 本电动工具仅可用于干法研磨。水进入电动工具

将增加电击危险。

u 注意火灾危险！应避免磨料和研磨机过热。每次

工作休息前都要清空集尘腔。集尘袋、微过滤
器、纸袋（或者吸尘器的过滤袋或过滤器）内的
磨削粉尘可能会在不良条件下（例如研磨金属时
火花飞溅）被点燃。如果磨削粉尘与油漆或聚氨
酯残余物或者其他化学原料混合，且磨料在长时
间作业后产生高温时，会产生极大危险。

Bosch Power Tools 1 609 92A 4C2 | (14.01.2019)