Bosch Power Tools 11263EVS User Manual

IMPORTANT: IMPORTANT : IMPORTANTE:

Read Before Using Lire avant usage Leer antes de usar

Operating/Safety Instructions
Consignes de fonctionnement/sécurité

Instrucciones de funcionamiento y seguridad

11263EVS

Call Toll Free

for Consumer Information

& Service Locations

Pour renseignement des

consommateurs et centres

de service, appelez au

numéro gratuit :

Llame gratis para
obtener información
para el consumidor y

ubicaciones de servicio

1-877-BOSCH99 (1-877-267-2499) www.boschtools.com

General Safety Rules

WARNING

!

all of the warnings listed below refers to your mains-operated (corded) power tool or battery­operated (cordless) power tool.

Read all instructions. Failure to follow all instructions listed below may
result in electric shock, fire and/or serious injury.

The term “power tool” in

SAVE THESE INSTRUCTIONS

Work area safety

Keep work area clean and well lit.

Cluttered or dark areas invite accidents.

Do not operate power tools in explosive
atmospheres, such as in the presence of
flammable liquids, gases or dust.

tools create sparks which may ignite the dust
or fumes.

Keep children and bystanders away while
operating a power tool.

cause you to lose control.

Distractions can

Power

Electrical safety

Power tool plugs must match the outlet.
Never modify the plug in any way. Do not
use any adapter plugs with earthed
(grounded) power tools.

and matching outlets will reduce risk of
electric shock.

Avoid body contact with earthed or
grounded surfaces such as pipes,
radiators, ranges and refrigerators.

is an increased risk of electric shock if your
body is earthed or grounded.

Do not expose power tools to rain or wet
conditions.

increase the risk of electric shock.

Do not abuse the cord. Never use the cord
for carrying, pulling or unplugging the
power tool. Keep cord away from heat, oil,
sharp edges or moving parts.

entangled cords increase the risk of electric
shock.

When operating a power tool outdoors,
use an extension cord suitable for
outdoor use.

outdoor use reduces the risk of electric
shock.

Do not use AC only rated tools with a DC
power supply.

work, the electrical components of the AC
rated tool are likely to fail and create a
hazard to the operator.

Water entering a power tool will

Use of a cord suitable for

While the tool may appear to

Unmodified plugs

There

Damaged or

If operating the power tool in damp
locations is unavoidable a Ground Fault
Circuit Interrupter (GFCI) must be used to
supply the power to your tool.

personal protection devices like electrician’s
rubber gloves and footwear will further
enhance your personal safety.

GFCI and

Personal safety

Stay alert, watch what you are doing and
use common sense when operating a
power tool. Do not use a power tool while
you are tired or under the influence of
drugs, alcohol or medication.

inattention while operating power tools may
result in serious personal injury.

Use safety equipment. Always wear eye
protection.

mask, non-skid safety shoes, hard hat, or
hearing protection used for appropriate
conditions will reduce personal injuries.

Avoid accidental starting. Ensure the
switch is in the off-position before
plugging in.

finger on the switch or plugging in power
tools that have the switch on invites
accidents.

Remove any adjusting key or wrench
before turning the power tool on.

or a key left attached to a rotating part of the
power tool may result in personal injury.

Do not overreach. Keep proper footing
and balance at all times.

better control of the power tool in unexpected
situations.

Dress properly. Do not wear loose
clothing or jewelry. Keep your hair,
clothing and gloves away from moving
parts.

be caught in moving parts.

If devices are provided for the connection
of dust extraction and collection facilities,
ensure these are connected and properly
used.

related hazards.

Safety equipment such as dust

Carrying power tools with your

Loose clothes, jewelry or long hair can

Use of these devices can reduce dust-

A moment of

A wrench

This enables

2-

-

Keep handles dry, clean and free from oil
and grease.

control the power tool.

Slippery hands cannot safely

Power tool use and care

Do not force the power tool. Use the
correct power tool for your application.

The correct power tool will do the job better
and safer at the rate for which it was
designed.

Do not use the power tool if the switch
does not turn it on and off.

that cannot be controlled with the switch is
dangerous and must be repaired.

Disconnect the plug from the power
source and/or the battery pack from the
power tool before making any
adjustments, changing accessories, or
storing power tools.

measures reduce the risk of starting the
power tool accidentally.

Store idle power tools out of the reach of
children and do not allow persons
unfamiliar with the power tool or these
instructions to operate the power tool.

Power tools are dangerous in the hands of
untrained users.

Maintain power tools. Check for
misalignment or binding of moving parts,
breakage of parts and any other condition
that may affect the power tools operation.
If damaged, have the power tool repaired
before use.

poorly maintained power tools.

Keep cutting tools sharp and clean.

Properly maintained cutting tools with sharp

Many accidents are caused by

Any power tool

Such preventive safety

cutting edges are less likely to bind and are
easier to control.

Use the power tool, accessories and tool
bits etc., in accordance with these
instructions and in the manner intended
for the particular type of power tool,
taking into account the working
conditions and the work to be performed.

Use of the power tool for operations different
from those intended could result in a
hazardous situation.

Use clamps or other practical way to
secure and support the workpiece to a
stable platform.

or against your body is unstable and may
lead to loss of control.

Empty dust container frequently,
especially when sanding wood with
polyurethane, varnish, shellac or similarly
coated surface.

dust may self ignite and cause fire.

Holding the work by hand

Fine particles of sanding

Service

Have your power tool serviced by a
qualified repair person using only identical
replacement parts.

safety of the power tool is maintained.

Develop a periodic maintenance schedule
for your tool. When cleaning a tool be
careful not to disassemble any portion of
the tool since internal wires may be
misplaced or pinched or safety guard
return springs may be improperly
mounted.

gasoline, carbon tetrachloride, ammonia, etc.
may damage plastic parts.

Certain cleaning agents such as

This will ensure that the

SAVE THESE INSTRUCTIONS

Rotary Hammer Safety Rules

Hold tools by insulated gripping surfaces
when performing an operation where the
cutting tool may contact hidden wiring or it
own cord.

exposed metal parts of the tool "live" and
shock the operator.

into existing walls or other blind areas where
electrical wiring may exist. If this situation is
unavoidable, disconnect all fuses or circuit
breakers feeding this worksite.

Contact with a "live" wire will make

Do not drill, fasten or break

Wear ear protectors when using the tool for
extended periods.

high intensity noise can cause hearing loss.

Use a metal detector to determine if there
are gas or water pipes hidden in the work
area or call the local utility company for
assistance before beginning the operation.

Striking or cutting into a gas line will result in
explosion. Water entering an electrical device
may cause electrocution.

-

3

-

Prolonged exposure to