Bompani BOCA080-E User Manual [it]

A. Programme selector

B. Programme sequence indicator

C. “Variable spin” button

D. “Start/Pause” button

E. “Reset” button

F. “Door open” indication

PROGRAMME CHART

This washing machine is equipped with

automatic safety functions which detect and diagnose faults at an early stage and react appropriately: G. “Service” indication H. “Water tap closed” indication I. “Clean pump” indication

Do not use liquid detergent for main wash if you

have activated prewash option.

For improved garment care, spin speed is restricted

to 400 rpm in this programme.

Selectable for programmes Cotton 60 and 40°C only.

Max.

Programme

Cotton

40 - 60 - 95 °C

Synthetics

30 - 40 - 60 °C

Delicates

30 - 40 °C

Daily load

40 °C

Quick wash 15´

30 °C

Wool

Cold - 40 °C

Handwash

30 - 40 °C

Rinse & Spin – 5.0 Same as the last rinse and the final spin in the “Cotton” programme. – –

Spin – 5.0 In this programme spinning is intensive. Same as the spin cycle in the “Cotton” programme. – – – – – –

40 - 60 - 95°C

30 - 40 - 60°C

30 - 40°C

40°C

30°C

- 40°C

30 - 40°C

Care

Labels

Load

5.0

3.0

1.5 Curtains and delicate clothing, dresses, skirts, shirts and blouses.

3.0 Slightly to normally soiled textiles made of cotton and/or synthetics. – Yes

3.0

1.0

1.0 Textiles made of linen, silk, wool and viscose marked as “handwashable”. – Yes

- for temperature selection, respect the manufacturer's recommendations on the care label

Normally to heavily soiled bed linen, table linen and underwear, towels, shirts etc. made of cotton and linen.

For washing heavily soiled laundry, the “Prewash” option can be selected.

Normally soiled blouses, shirts, overalls etc. made of polyester (Diolen, Trevira), polyamide (Perlon, Nylon).

Refreshed briefly worn outer clothing made of cotton, artificial fibers and blends with cotton.

Use lowest recommended detergent amount.

Only woollens with a felt-free finish, labelled with the woolmark and identified as machine washable.

Type of wash / Notes

Detergents and Additives Special options Max. Pre-

wash

Main

Wash

Yes

– Yes

Softener Rinse

hold

i i i i

i i i i i

i i i

i i

Pre-

wash

– –

Rapid Variable

–

spin

Spin

Speed

rpm

max.

400

max.

Gentle Spin – 1.0 In this programme spinning is gentle. Same as the spin cycle in the “Wool” programme. – – – – – –

Drain – – Drain only - no spinning. Alternative method of terminating programme after “Rinse Hold”. – – – – – – – –

N.B. This machine is controlled by sensors. Please avoid excessive detergent dosing.

i: optional / Yes : dosing required

5019 612 10243

max.

CONSUMPTION DATA

Programme

Temperature

(°C)

Load

(kg)

Water

(l)

Energy

without “Rapid”

(kWh)

Approx. Programme Duration (hrs : min)

without “Rapid” with “Rapid”

Cotton 95 5.0 50* 1.70 2:05 – Cotton** 60 5.0 47 0.89 2:45 2:10 Cotton** 60 2.5 32 0.68 2:10 ***

Cotton 40 5.0 47 0.65 2:00 1:45 Cotton** 40 2.5 32 0.52 1:45 ***

Synthetics 60 3.0 50* 0.90 2:05 1:14 Synthetics 40 3.0 40 0.50 1:50 0:59

Delicates 40 1.5 50 0.55 0:45 –

Daily load 40 3.0 40 0.45 1:00 –

Quick wash 15´ 30 3.0 30 0.15 0:15 –

Wool 40 1.0 55 0.55 0:45 –

Handwash 40 1.0 40 0.40 0:35 –

Consumption values were measured in normalized conditions in compliance with standard IEC/EN 60 456. Consumption data in the home may vary with respect to the values in the table in relation to the water supply pressure and temperature, the load and the type of wash.Water and energy consumption refer to the default setting of the programmes; selecting special options or modifying spin speed or temperature will change the consumption data. The programme duration may differ from the values indicated above as it depends on the operation conditions applicable at that time (see also “Troubleshooting Guide” in your Instructions for Use). * To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump drains the water out. ** Reference Programmes for Energy Label. *** Automatic adaption of programme duration after detection of wash load.

PREPARATION OF THE WASH CYCLE

1. Load the machine, close the drum doors and check that they are properly locked.

2. Add detergent and additives into the dispenser to no more than the “MAX” level mark, as follows:

• Programme with pre and main wash

• Main wash programme without prewash

• Fabric softeners and conditioners

• Stain remover agents

• Anti-scale agents (if necessary)

3. Close the lid.

4. Turn the programme selector to the desired programme and temperature. The lamp next to the “Start/Pause” button flashes. The indication lamp of the predefined spin speed lights up.

SELECT THE DESIRED OPTION(S)

Selecting or deselecting an option can be done at any time during the programme. The option will be applied as long as the corresponding programme phase has not been executed yet.

“Rinse hold” button

• The laundry remains in the last rinse water without progressing to the final spin cycle to avoid creasing and prevent colours from changing.

• This option is particularly recommended for the “Synthetics”, “Daily load” and “Delicates”

• If you select “Rinse Hold”, do not leave items to soak for too long.

• As soon as the appliance stops in the rinse hold, the “Rinse hold” lamp of the sequence indicator lights up and the lamp next to the “Start/Pause” button flashes.

Terminate the “Rinse hold” option:

• Press the “Start/Pause” button; the programme will terminate automatically with the final spin cycle for the present wash programme.

• If you do not wish to spin the clothes, turn the programme selector knob to the “Drain” programme and press the “Start/Pause” button.

“Prewash” button

• Only for heavily soiled loads (for example sand, granular dirt). Increases the cycle time by approximately 20 min.

“Rapid” button

• Enables quicker washing by shortening the programme duration.

• Recommendable for small loads or only lightly soiled laundry.

“Variable spin” button

• Every programme has a predefined spin speed.

• Press the button to set another spin speed.

• If spin speed “0” is selected, the final spinning is cancelled but intermediate spin peaks remain during the rinse. The water is drained out only.

programmes.

• It is useful if you want to postpone spinning to a later time, or if you want to drain out only.

PROGRAMME START

Open the tap and press the “Start/Pause” button. The indication lamp next to the “Start/Pause” button lights up. The programme sequence indicator shows the current programme phase, running from left to right through Wash, Rinse, Spin/Drain. When the programme phrase is finised, the corresponding indication goes out.

• Note: If there is a power interruption or if the appliance is disconnected during the cycle, the programme will run again from the point where it was interrupted.

“DOOR OPEN” INDICATION

Before starting and after end of a programme, the lamp lights to show the the lid can be opened. As long as a wash programme is running, the lid remains locked and must on no account be forced open. In case you have an urgent need to open it during a running programme, refer to “Cancel (Reset) a running programme before the end”.

FAILURE INDICATIONS

In case of any failures or irregularities, consult the “Troubleshooting Guide” in your Instructions for Use.

“Service”

Lighting up of the “Service” indication can be caused by a fault in an electrical component. Refer to the “Troubleshooting Guide” in your “Instructions for Use”; if the fault persists, contact our After Sales Service.

“Water tap closed”

The appliance has no or insufficient water supply. Open the water tap: if the indications still lights up, refer to the “Troubleshooting Guide” in the Instructions for Use.

“Clean pump”

Waste water is not pumped out. Check whether the drain hose is kinked or the filter must be cleaned: in the latter case refer to the Instructions for Use (“Removing the Filter”).

PROGRAMME END

• All the lights of the programme sequence indicator

are off, and the “Door open” indication lights up.

1. Turn the programme selector to the “Off/O” position.

2. Close the water tap.

3. Open lid and drum and unload the machine.

4. Leave the lid open for some time to allow the interior of the machine to dry.

CHANGE PROGRAMME AND/OR OPTIONS AFTER PROGRAMME START

1. Press the “Start/Pause” button to pause the programme. The light flashes.

2. Select the new programme, any options and another spin speed if you want.

3. Press the “Start/Pause” button again. The new programme continues at the same position where the previous programme was interrupted. Do not add detergent for this programme.

CANCEL (RESET) A RUNNING PROGRAMME BEFORE THE END

The “Reset” button cancels a programme before the end. Press the “Reset” button for at least 3 seconds. Any existing water is drained out before the door can be opened.

5019 612 10243

+ 2 hidden pages