Bogen WBS810T725, WBS8T725BRV Data Sheet
Features
Wall Baffle Wooden
Speaker Assemblies
Models
WBS8T725 & variations,
WBS810T725
• 4-watt capacity
• 6 power taps available (4, 2, 1, 1/2, 1/4, 1/8 watts)
• Works with both 70V and 25V amplifier outputs
• Simulated walnut finish
• Pre-assembled for faster installation
• 8" cone speaker for excellent audio quality
• 6 oz. or 10 oz. magnet weights
• Recessed volume control available (V models only)
• Screw terminals available (BR models only)
• Easy wall-mount installation
• Mounting hardware included
Specifications subject to change without notice.
© 2008 Bogen Communications, Inc.
54-7777-09A 0808
WBS8T725
Description
Bogen Wall Baffle Speakers consist of 8" cone speakers (S86 or S810) pre-assembled into a simulated walnut-finished wooden enclosure with a black grille cloth on front.These wall baffles are handsomely styled
and ruggedly built with 3/8" particle board reinforced at the corners. Designed for wall mounting, the face
is angled downward 13.5 degrees. Available options include recessed volume control and terminal strip.
Technical
Specifications
Model
Pow er Ta ps
(in Watts)
Frequency Response
Sensitivity (4 ft./1W)
Magnet Weight
No Volume Control
Recessed Volume
Control (V)
Screw Terminals (BR)
Shipping Weight
(4/Carton)
Dimensions
WBS8T725
4, 2, 1, 1/2, 1/4, 1/8
@25V & 70V
50 Hz-
12 kHz
95
dBspl
6 oz.
●
18 lb. /
carton
9-1/2" W x
9-1/2" H x
5-1/4" D
(3-1/4" D
@ bottom)
WBS8T725V
●
WBS8T725BR
● ●
WBS8T725BRV
● ●
19 lb. /
carton
WBS810T725
70 Hz-
15 kHz
96
dBspl
10 oz.
●
20 lb. /
carton
50 Spring Street, Ramsey, NJ 07446, U.S.A.
Tel: 201-934-8500; FAX: 201-934-9832; www.bogen.com
WBS8T725 The surface-mounting loudspeaker
assembly shall be a Bogen model WBS8T725
(or WBS8T725V, WBS8T725BR, or
WBS8T725BRV), or equivalent, 8" cone-type
loudspeaker having a frequency response of at least
50 Hz to 12 kHz. Axial sensitivity shall be 95 dB,
measured at 1-watt/4 feet. The loudspeaker shall
have a 6 oz. ceramic magnet and a 3/4" voice coil. A
transformer, capable of matching an 8-ohm loudspeaker to a 25-volt or 70-volt line, and providing
power taps of 4, 2, 1, 1/2, 1/4, and 1/8 watts shall be
included. The transformer primary and secondary
leads shall be stripped, tinned, and shall be at least 6"
in length.
The loudspeaker shall be assembled in a wall baffle
for surface mounting, angled 13.5 degrees for downward sound dispersion. The baffle shall be constructed of 3/8” particle board, glued and covered in
simulated walnut vinyl. Glue blocks shall be used to
reinforce all side corner joints. The speaker opening
shall be covered with a black grille cloth. Overall
dimensions shall be 9-1/2" W x 9-1/2" H x 5-1/4" D
(top) x 3-1/4" D (bottom).
(For WBS8T725V add) The assembly shall include
a control for adjusting the volume of the loudspeaker.
(For WBS8T725BR add) A terminal strip shall
be included for connection of the audio line.
Terminals shall be labeled for 4, 2, 1, 1/2, 1/4, and
1/8-watt power connection.
(For WBS8T725BRV add) A terminal strip shall
be included for connection of the audio line.
Terminals shall be labeled for 4, 2, 1, 1/2, 1/4, and 1/8-
watt power connection. A control shall also be included for adjusting the volume of the loudspeaker.
WBS810T725 The surface mounting loudspeaker
shall be a Bogen model WBS810T725, or equivalent, 8" cone-type loudspeaker having a frequency
response of at least 70 Hz to 15 kHz. Axial sensitivity shall be 96 dB, measured at 1-watt/4-feet. The
loudspeaker shall have a 10 oz. ceramic magnet and
a 1" voice coil. A transformer, capable of matching
an 8-ohm loudspeaker to a 25-volt or 70-volt line,
and providing power taps of 4, 2, 1, 1/2, 1/4, and 1/8
watts shall be included. The transformer primary
and secondary leads shall be stripped, tinned, and
shall be at least 6" in length.
The loudspeaker shall be assembled in a wall baffle
for surface mounting, angled 13.5 degrees for downward sound dispersion. The baffle shall be constructed of 3/8" particle board, glued and covered in
simulated walnut vinyl. Glue blocks shall be used to
reinforce all side corner joints. The speaker opening
shall be covered with a black grille cloth. Overall
dimensions shall be 9-1/2" W x 9-1/2" H x 5-1/4" D
(top) x 3-1/4" D (bottom).
Architect
and Engineer
Specifications
Line
Drawings
Rear View
Side View
WBS8T725BR
Loading...